iTextAlert ITA1SENAA ITA-1 Sensor AA User Manual Quick Start Guide

iTextAlert LLC ITA-1 Sensor AA Quick Start Guide

Quick Start Guide

Quick Start GuideModel iTA-1 Rev. AiTextAlert, LLC111 East First StreetGeneseo, Illinois 61254Customer Service: 855-810-2992www.iTextAlert.comSetup WizardPower OnInstall included Li-ion battery into Hub. Connect the included AC power adapter to Hub.1ActivationLog into www.iTextAlert.com or call 855-810-2992 to activate the system. Once activation has been completed, follow the on-screen instructions.2Hub NameEnter a name or identifier for the Hub. This is the identifying name that you (and your designated contacts) will receive SMS (text) messages from on your cell phone. 5PasswordYou have the option to create a four-digit password that would allow only you to make changes to the system settings.3SensorsConnect sensors to the Hub via the provided USB cable and follow on-screen instructions to synchronize the sensors with the Hub.6Wi-FiConnecting to a Wi-Fi network provides a second method for the Hub to transmit alerts to your cell phone. If there is no Wi-Fi network or the network 4ContactsEnter the name(s) and cell phone number(s) of those persons that are to be notified of any alerts via SMS (text) messaging.7REF. DOC. QS-ITA1 REV A, 10/2011 FCC ID: Z3GITA1HUBbecomes disabled, the Hub will transmit alerts using the cellular telephone network. The Hub can only connect to one Wi-Fi network.Welcome, Thank you for purchasing the iTA-1 monitoring and alerting system. With this product, you have the ability to monitor up to 8 remote sensing devices using wireless technology and the convenience of your cell phone. The iTA-1 allows you to receive alerts from and to send commands to your Hub via SMS (text) messaging.To begin using your system, please register either logging into www.iTextAlert.com or calling 855-810-2992. Please note that the activation reminder will be present on your Hub until it has been registered. You will not receive SMS alerts to your cell phone until you have completed activation.For customer service or technical support, please call 855-810-2992 between the hours of 7:00 AM to 7:00 PM Central time zone, Monday through Friday or visit us at www.iTextAlert.com.ActivationPer FCC 15.21 changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Per FCC 15.19(a)(3) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Hard Key Functions•Press and hold hard for 5 seconds to place Hub in sleep mode.•Press and release the hard key to wake the Hub from sleep mode. (Note: Do not hold the hard key down.)If the system shuts down, use a paperclip to hit the Reset button on the back side of the Sensor. Push in carefully until the button clicks.Hub Hard KeyThe hard key is used to put the Hub in sleep mode, wake the Hub up from sleep mode, and reboot the system. The Hub will only power down when the battery pack is depleted.Installing The Sensor’s BatteryRemove screw from back battery cover.1Slide battery cover to access battery area.23Insert battery according to diagram.Hub & Sensor Item List1 - iTextAlert Hub with built-in power Sensor (control panel)2 - mounting screws1 - Rechargeable Li-ion battery (3.7V, 1150 mAh, 4.3 Wh)1 - AC power supply (Input: 110-120V, 50-60 Hz, 0.15A Output: 5V, 1A)1 - USB cable1 - USB plug (to protect the port)1 - wall mount or desk stand bracket2 - pieces of double-sided tapeQuick Start GuideItems included with the optional Sensor packages: 1 - wall mount bracket1 - USB plug (to protect the port)2 - mounting screws1 - AA or AAA battery2 - piece of double-sided tapeQuick Start GuideOpen/Close SensorTemperature SensorWet/Dry SensorStationary/Move SensorWall Mount Installation (Hub and Sensors)Use the mounting bracket as a template to mark pilot holes for the mounting screws.Pilot holes may not be necessary in some materials1Sensor wall mountiText Hub wall mountDrill 1/16” pilot holes. Install the mounting bracket using the included screws.2Fasten the Hub or Sensor to the bracket.The double-sided tape may be used to fasten the mounting bracket instead of securing with the screws.3Installing The Hub’s BatterySlide Hub cover to access battery area.1Pull battery tab from battery.2Plug in supplied AC power adapter to Hub.4Replace battery and cover on Hub.3Note: the Hub will not operate without the battery installed. Please install battery prior to operating the device.Note: please push on the power button to access the hard key.Note: Hub must have battery installed and AC adapter plugged in to opterate.
Please cut along the dotted lines for a quick reference sheet.Remote Configuration Commands:You can send a SMS command to the Hub. XY Command Sensor1Y - Disarm2Y - Arm3Y - Dismiss ex. Send “25” will Arm Sensor 5 (Kitchen)Sensor Screen Grid NumberReply CommandsSensor ListThe commands allow you to communicate with your Hub via SMS on your mobile device. 3 or MENU - Option Menu 4 or DISARM - Disarm System5 or ARM - Arm System6 - Reply to see Disarmed Sensor List 7 - Reply to see Armed Sensor List 8 or STATUS - Reply Sensor Disarmed/Armed Status9 or TEST - Send Test SMS to all contacts11 to 19 - Disarm individual Sensor21 to 29 - Arm individual Sensor31 to 39 - Dismiss individual SensorSMS NotificationsStationary/Move - alerts once the Sensor is physically moved.Open/Close - alerts once the Sensor disconnects/connects.Temperature - alerts once the Sensor has reached its threshold.Wet/Dry - alerts the Sensor has reached the wet/dry level based on its configuration.Power - alerts once the Hub has lost or regained power.Sensor TypesSMS signal strengthWi-Fi strengthHub battery levelSettings confirmationIncoming SMSOutgoing SMSEntire systemOther Graphics3 or OPTION4 or DISARM5 or ARM678 or STATUS9 or TESTOption MenuDisarm SystemArm SystemReply to see Disarmed Sensor List Reply to see Armed Sensor ListReply to see all Sensor Disarmed/Armed StatusSend Test SMS to all contacts11-Disarm 21-Arm 31-Dismiss12-Disarm 22-Arm 32-Dismiss13-Disarm 23-Arm 33-Dismiss14-Disarm 24-Arm 34-Dismiss15-Disarm 25-Arm 35-Dismiss16-Disarm 26-Arm 36-Dismiss17-Disarm 27-Arm 37-Dismiss18-Disarm 28-Arm 38-Dismiss19-Disarm 29-Arm 39-Dismiss1.3.2.4.5.6.7.8.9.Sensor StatusStatus IndicatorStatus IndicatorSensor TypeSensor LocationKitchenArmed With SystemThe Sensor will arm when selected on the Sensor Menu or when the system is armed.Always OnThe Sensor will remain armed even when the system is disarmed.Sensor ArmedSensor Disarmed Sensor AlertSensor ArmedBattery LowSensor DisarmedBattery LowSensor AlertBattery LowContactsLists the designated contacts (maximum of 5).Event LogChronologically lists the last 50 system events.SensorsLists the maximum of 9 sensors (Power is a default Sensor).Settings:Lists the settings for the Hub and Sensors.Sensor ConfigureLists all the sensors, their types, and their locations. From this screen, individual sensors can be edited or deleted.Note: After the initial setup, Sensor Settings can be edited without connecting the Sensor to Hub via the provided USB cable.Menu NavigationScreenpositionPress the right or left scroll buttons to access the different menus.Additional SensorsGo to Sensor Configuration screen and press [+ symbol] to add a Sensor (maximum of 8).12The connecting screen will appear; once the Hub recognizes the Sensor, the screen will advance to the specific Sensor Settings screen.Adjust the settings; then press the [√ symbol] to confirm the settings.Connect the Sensor to the Hub via the provided USB cable.34Note: When resetting the sensor, it is not required to connect the Sensor to the Hub via USB cable.

Navigation menu