Zebra Technologies AP716101 Wireless Access Point User Manual AP 7161 Access Point Installation Guide

Zebra Technologies Corporation Wireless Access Point AP 7161 Access Point Installation Guide

Contents

User Manual

AP 7161 ACCESS POINT INSTALLATION GUIDE
2 AP 7161 Access Point Installation Guide
AP 7161 Access Point Installation Guide 3 Motorola Solutions reserves the right to make changes to any product to improve reliability, function, or design. Motorola Solutions does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Motorola Solutions products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Motorola Solutions products. Service Information If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact Motorola Solutions Support at: http://motorolasolutions.com/support.
4 AP 7161 Access Point Installation Guide Introduction.................................................................................................................................................................................... 5 Document Conventions.................................................................................................................................................................. 6 AP 7161 Hardware.......................................................................................................................................................................... 7 AP 7161 Antenna Assessories................................................................................................................................................. 7 AP 7161 2.4 GHz Antennas ............................................................................................................................................... 7 AP 7161 4.9 GHz and 5 GHz Antennas ............................................................................................................................... 8 AP 7161 Multi Band Antennas .......................................................................................................................................... 8 Outdoor PoE Hardware and Mounting Accessories................................................................................................................. 9 AP 7161 Mounting Accessories............................................................................................................................................... 9 AP 7161 Weatherized Ethernet Accessory............................................................................................................................... 9 Package Contents......................................................................................................................................................................... 10 Hardware Installation Guidelines................................................................................................................................................. 11 Precautions................................................................................................................................................................................... 11 Warnings...................................................................................................................................................................................... 12 Access Point Placement............................................................................................................................................................... 13 AP 7161 Hardware Overview........................................................................................................................................................ 14 AP 7161 Ports and Connections.................................................................................................................................................... 14 AP 7161 Antenna Connectors................................................................................................................................................ 14 AP 7161 Console, GE1/POE and GE2 Ports............................................................................................................................. 16 AP 7161 Grounding Screw..................................................................................................................................................... 17 AP 7161 Factory Reset Hardware Button............................................................................................................................... 18 LED Indicators............................................................................................................................................................................... 18 Two Radio LEDs..................................................................................................................................................................... 19 Three Radio LEDs................................................................................................................................................................... 20 AP 7161 Hardware Mounting and Installation............................................................................................................................. 21 Mounting Bracket Kit............................................................................................................................................................. 21 Extension Arm Kit................................................................................................................................................................... 22 Pole Mounted Installations.................................................................................................................................................... 24 Vertical Pole Mount............................................................................................................................................................... 25 Wall Mounted Installations................................................................................................................................................... 28 AP 7161 Power Options Using Power over Ethernet.................................................................................................................... 31 Basic AP 7161 Configuration........................................................................................................................................................ 32 Antenna Type Configuration...................................................................................................................................................32 Automatic Channel Select Override....................................................................................................................................... 32 Specifications............................................................................................................................................................................... 33 Basic Troubleshooting.................................................................................................................................................................. 36 Regulatory Compliance................................................................................................................................................................ 37 Motorola Solutions Support Center.............................................................................................................................................. 49 AP 7161 Series RoHS Compliance................................................................................................................................................ 50
AP 7161 Access Point Installation Guide 5 Introduction Perfect for extending network coverage to outside areas, the AP 7161 brings the latest 802.11n 3x3 Multiple Input Multiple Output (MIMO) tri-radio design together with rugged outdoor performance. True perimeter security is provided using either a dedicated dual band sensor or software mode for both 2.4GHz and 5GHz bands to deliver 24x7 rogue detection and termination. The AP 7161 is optimized with Motorola Solutions WiNG 5 intelligence, extending QoS, security, and mobility services to the access point to support better capacity and performance. The AP 7161 is ideal for industrial, enterprise campus, video surveillance, public safety, and smartgrid utility deployments to extend to the outdoors. Deployments can be managed using the Motorola Solutions WiNG 5 architecture. The WiNG 5 architecture is a solution designed for 802.11n networking. It leverages the best aspects of independent and dependent architectures to create a smart network that meets the connectivity, quality, and security needs of each user and their applications based on the availability of network resources, including wired networks. WiNG 5 is a Third Generation WLAN solution which incorporates the best of both the first generation Autonomous Access Point WLAN and the second generation Centralized Controller Based WLAN. The control plane is now distributed between the access points and the controllers. The network administrator has the flexibility of directing the data plane either being forwarded directly from the access points, or via the controllers. By distributing intelligence and control between the wireless controllers and APs, the WiNG 5 network can route directly via the best path, as determined by factors including the user, the location, the application, and the available wireless and wired resources. Once adopted by a Motorola Solutions RFS4000, RFS6000, or RFS7000 series controller, the AP 7161 is managed as an Adaptive AP running the WiNG 5 network management protocol. WiNG 5 networks extend the current differentiation that Adaptive APs offered to the next level by now having the services and security available at every point in the network. The traffic flow is optimized to prevent wired congestion, as well as wireless congestion. Traffic flows dynamically, based on user and application, and finds alternate routes to work around any possible network choke points. Mixed-media application optimization is the hallmark of WiNG 5 networks. Extending the indoor network to the outdoors increases the need to guard against unwanted intruders and attackers, and monitor network performance and availability. In addition to industry standard security for clients and radio backhaul, the AP 7161 provides true perimeter security using either a dedicated dual band sensor or software mode in the 2.4GHz and 5Ghz bands. Concurrent around-the-clock dual band Network Assurance sensing and wireless traffic is provided together with spectrum analysis, eliminating the need for separate devices. An access point can function as a Wireless Intrusion Protection System (WIPS) sensor and upload sensor mode operation information to a dedicated WIPS server. WIPS protects your wireless network, mobile devices, and traffic from attacks and unauthorized access. WIPS provides tools for standards compliance and around-the-clock 802.11a/b/g wireless network security in a distributed environment. WIPS allows administrators to identify and accurately locate attacks, rogue devices, and network vulnerabilities in real time and permits both a wired and wireless lockdown of wireless device connections upon acknowledgement of a threat.
6 AP 7161 Access Point Installation Guide Capacity in video surveillance solutions is critical to the performance of many networks designed to monitor and provide safety. To assist with the deployment of video surveillance networks where the camera application resides, the AP 7161 offers band unlocked radio flexibility. The user can choose between 2.4Ghz, 5Ghz and 4.9Ghz bands for the radio type. The AP 7161 supports 3x3 MIMO technology, reaching a maximum data rate of 300 Mbps to maintain high performance and better quality of transmission. The AP 7161 is designed to optimize network availability through preemptive intelligence which dynamically senses weak or failing signals, securely moves mobile users to alternate APs, and boosts signal power to automatically fill RF holes and ensure uninterrupted mobile user access. The AP 7161 band unlocked radios allow flexibility and deployment options for the public safety market. The powerful radio increases coverage, performance, and obstruction penetration for outdoor use. Receiver sensitivity is increased proportionally so users have an increased ability to maintain high performance access for mobility and client devices in the network. For the latest version of this guide go to: http://supportcentral.motorola.com. Document Conventions The following graphical alerts are used in this document to indicate notable situations: NOTE Tips, hints, or special requirements that you should take note of. CAUTION Care is required. Disregarding a caution can result in data loss or equipment malfunction. WARNING! Indicates a condition or procedure that could result in personal injury or equipment damage.
AP 7161 Access Point Installation Guide 7 AP 7161 Hardware There are currently four AP 7161 access point models: Model Part Number Description AP-7161-66040-US AP 7161 OUTDOOR DUAL RADIO 802.11N US AP-7161-66040-WR AP 7161 OUTDOOR DUAL RADIO 802.11N INTL AP-7161-66S40-US AP 7161 OUTDOOR DUAL RADIO 802.11N AP WITH SENSOR US AP-7161-66S40-WR AP 7161 OUTDOOR DUAL RADIO 802.11N WITH SENSOR INTL AP 7161 Antenna Accessories The AP 7161 antenna suite includes the following optional antenna accessories. The antennas do not ship wth the AP 7161 models listed in the table above and must be ordered separately. AP 7161 2.4 GHZ Antennas Part Number Band Gain Height (inches) Antenna Description ML-2499-HPA8-01 2.4 8 19.5 Outdoor rated Type: dipole Gain: 8dBi@2.4GHz Connector: N-male ML-2499-HPA4-01 2.4 4 9.0 Outdoor rated Type: dipole Gain: 4dBi@2.4GHz Connector: N-male RAN4054A 2.4 8 21 Outdoor rated Type: dipole Gain: 8dBi@2.4GHz Connector: N-male
8 AP 7161 Access Point Installation Guide AP 7161 4.9 GHz and 5 GHz Antennas Part Number Band Gain Height (inches) Description ML-5299-HPA10-01 4.9-5.8 10 19.5 Indoor and Outdoor rated Type: dipole Gain: 10dBi@4.9GHz Connector: N-male ML-5299-HPA5-01 5.2-5.8 5 6.75 Indoor and Outdoor rated Type: dipole Gain: 5dBi@5.0GHz Connector: N-male ML-5299-FHPA6-01 4.9-5.8 8 11 Outdoor rated Type: dipole Gain: 8dBi@4.9-5.8GHz Connector: N-male AP 7161 Multi Band Antenna Part Number Band Gain Height (inches) Description ML-2452-HPAG5A8-01 2.4-5.8 4.5/7.5 11 Outdoor rated Type: dipole Gain: 4.5dBi@2.4GHz, 7.5dBi@5GHz, 5.5dBi@4.9GHz Connector: N-male MT-465019/NVD 4.9-5.8 19 Outdoor only rated Type: panel ML-2452-PNL9M3-036 2.4-5.8 8/10.7 Indoor and Outdoor rated Type: panel ML-2452-VMM3M3-036 2.4-5.8 6 peak Outdoor rated Type: vmm PDM24516-MT1 2.4-5.8 8.3/10.1 Indoor and Outdoor rated Type: patch
AP 7161 Access Point Installation Guide 9 Outdoor PoE Hardware and Mounting Accessories The AP 7161 is a Power over Ethernet (PoE) device. When deployed, the use of an outdoor rated PoE power supply and mounting bracket may be required. The recommended Motorola Solutions PoE accessories are listed in the following table. For more information, see AP 7161 Power Options Using Power over Ethernet (PoE) on page 31. Part Number Description AP-PSBIAS-7161-US Outdoor IP66 802.3AT gigabit Ethernet power injector, 100-240 VAC US AP-PSBIAS-7161-WW Outdoor IP66 802.3AT gigabit Ethernet power injector, 100-240 VAC International KT-153143-01 Outdoor PoE mounting kit AP 7161 Mounting Accessories The AP 7161 has a flexible three piece mounting kit, together with an optional standoff extension arm for pole mounting. For more information, see AP 7161 Hardware Mounting and Installation on page 21. Part Number Description KT-147407-01 AP 7161 mounting hardware kit KT-150173-01 AP 7161 12 inch extension arm for mounting kit AP 7161 Weatherized Ethernet Accessory One RJ45 weatherized connector plug is included with each AP 7161 access point. If additional plugs are required, they can be ordered using the part number listed in the following table: Part Number Description KT-153676-01 AP 7161 RJ45 weatherized Ethernet plug
10 AP 7161 Access Point Installation Guide Package Contents Carefully remove all protective packing material from around the AP 7161 access point and save the container for later storage and shipping. Refer to AP 7161 Hardware on page 7 when verifying that all AP 7161 hardware has been received. Record the serial numbers on the shipping cartons and AP 7161 access points for warranty claims and reference during software download procedures. Each AP 7161 model number (see AP 7161 Hardware on page 7) includes the following parts: • AP 7161 access point • Weatherproof RJ45 plug kit • AP 7161 Access Point Installation Guide (this document) The following items are not included with the AP 7161 access point models but can be ordered from Motorola Solutions: • Antenna(s) • Mounting brackets/kits • PoE power supply and accessories • RFS controllers (if required) The following items are not provided by Motorola Solutions and can be sourced from local hardware suppliers, partners, or distributors: • Lightning protection unit • Cat5E cable to connect power source • Band clamps, lag bolts, or U-bolts • Grounding wire When opening the shipping cartons, inspect the equipment for damaged or missing parts (see AP 7161 Hardware on page 7). If you find any damaged or missing equipment, contact your distributor, partner, or Motorola Solutions Support immediately. For items that are not provided by Motorola Solutions, contact your local hardware suppliers.
AP 7161 Access Point Installation Guide 11 Hardware Installation Guidelines CAUTION All device wiring must comply with the National Electric Code (NEC) or regulations and procedures defined by the regulatory bodies of the country or region where the devices are being deployed. All local building and structure codes must be observed. WARNING! Strictly observe the following safety precautions and warnings when installing an AP 7161 access point. Precautions Before installing an AP 7161 model access point, verify the following grounding and lightning protection notes: • The installation professional should be familiar with all grounding requirements and regional codes and ensure that the access point and mounting asset are properly grounded. The grounding cable for an AP 7161 must be at a minimum a #10 gauge wire cross section. The cable can be attached to the unit using one of the following methods: • Loosen the grounding screw, insert the grounding cable into the hole below it, and tighten the screw. • Loosen the grounding screw, wind the grounding cable around it, and tighten the screw. • Attach a ring lug to the grounding cable and secure it to the unit using the grounding screw. • To properly attach the grounding cable to the access point, refer to AP 7161 Grounding Screw on page 17. • For Ethernet and lightning protection, it is recommended that a commercially available off-the-shelf Lightning Protection Unit (LPU) be used on all shielded CAT5E Ethernet connections. The LPU should be rated for outdoor use. • For the best possible protection, each access point requires an LPU be installed adjacent to the access point. If there is a LAN connection to an indoor network, a second LPU is required at the cable entry point to the building. CAUTION Lightning damage is not covered under the conditions of a standard Motorola Solutions product warranty. When installed correctly, Lightning Protection Units (LPUs) provide the best protection from the harmful effects of lightning. Observe all regional and national codes that apply for lightning protection. • Verify that the deployment environment has a continuous temperature range compatible with the operating temperature range of the device.
12 AP 7161 Access Point Installation Guide Warnings • Read all installation instructions and site survey reports, and verify correct equipment installation before connecting the access point to its power source. • Remove jewelry and watches before installing this equipment. • Verify that the unit is grounded before connecting it to the power source. • Verify that any device connected to this unit is properly wired and grounded. • Connect all power cords to a properly wired and grounded electrical circuit. Verify that the electrical circuits have appropriate overload protection. • Attach only approved power cords to the device. • Verify that the power connector and socket are accessible at all times during the operation of the equipment. • Do not hold any component containing a radio such that it is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting. • Do not work with power circuits in dimly lit spaces. • Do not install this equipment or work with its power circuits during thunderstorms or other weather conditions that could cause a power surge. • Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment operation specifications. • Avoid contact with overhead power lines. • Take precautions to avoid injury from falling tools and equipment. Crews should wear hard hats in and around the installation work site. • Be aware of vehicular traffic in and around the installation work site. • Do not operate a portable transmitter near unshielded blasting caps or in an environment where explosives are present unless the transmitter is especially certified for such use. • Refer to your site survey and network analysis reports to determine specific requirements for each deployment. • Assign installation responsibility to the appropriate personnel. • Identify and document where all installed components are located. • Identify and prepare Ethernet and console port connections. • Verify that cable lengths are within the maximum allowable distances for optimal signal transmission. CAUTION The maximum length allowed for PoE cables is 100 meters.
AP 7161 Access Point Installation Guide 13 Access Point Placement Observe the following recommended guidelines to help ensure a successful network deployment: • Identify all pieces of the mounting bracket and mounting extension arm hardware and ancillary hardware (see AP 7161 Hardware on page 7). • Mount the device with the black gore vent down. • Mounting height for network devices should not exceed 30 to 35 feet. Mounting height should vary to accommodate the topography of the deployment area, foliage, and other obstructions. • When mounting an access point, keep the antennas away from any metal obstructions. Utilize the extension arm (KT-150173-01) if neccesary. • Line of Sight (LoS) guidelines should be given special consideration whenever devices will not be installed in a straight line, such as deploying devices on alternating sides of a roadway.
14 AP 7161 Access Point Installation Guide AP 7161 Hardware Overview AP 7161 models can be purchased in a two or three radio configuration (see AP 7161 Hardware on page 7). Each model has two band unlocked radios that can operate across the 2.4GHz, 4.9GHz, and 5GHz bands, subject to country regulatory approval and outdoor/band use. An AP 7161 must be installed by trained professionals familiar with RF planning and regulatory limits defined by the regulatory bodies of the country where the devices are being deployed. All common precautions for grounding and Electrostatic Discharge (ESD) protection should be observed during deployment and installation. AP 7161 access points must be installed such that no harmful interference results from device operation. AP 7161 Ports and Connections The AP 7161 access point has the following port designations: • Antenna ports R1-A, B and C, R2-A, B and C, and R3-A and B • Console port • GE1/POE - LAN port • GE2 - WAN port The following sections describe the ports and connections for the AP 7161. AP 7161 Antenna Connectors AP 7161 two radio models (AP-7161-66040-US and AP-7161-66040-WR) are configured with six N type connectors to support two active WLAN data radios. When mounting antennas to ports R1-A, R1-B, and R1-C, ensure that you have selected the appropriate band for the configured radio that uses ports R1-A, R1-B, and R1-C. In this instance, R1 ports relate to the software configured radio 1 settings.
AP 7161 Access Point Installation Guide 15 When mounting antennas to connectors marked R2-A, R2-B and R2-C, these antenna ports relate to the software settings of radio 2. Care must be taken to provide the correct antenna for the operating band of each port. AP 7161 three radio models (AP-7161-66S40-US and AP-7161-66S40-WR) are configured with eight N type connectors to support two active WLAN data radios and a dedicated sensor radio as the third. As with two radio models, the rules for ports R1-A, R1-B and R1-C and R2-A, R2-B and R2-C apply. R3-A and R3-B are the ports reserved for the sensor radio, and an appropriate multi band antenna should be mounted to the unit for sensor operation. NOTE The sensor radio does not function as a WLAN data radio. WARNING! Antenna ports where no antenna is mounted must be properly terminated using an approved IP67 terminator.
16 AP 7161 Access Point Installation Guide AP 7161 Console, GE1/POE and GE2 Ports The AP 7161 has Ethernet ports for external console, GE1/POE, and GE2 connections.To gain access to the ports you will need to remove the protective caps. The Ethernet cable from the PoE device (if used) connects to the GE1/POE port on the unit.
AP 7161 Access Point Installation Guide 17 The GE2 port on the unit can be used if a second data connection for an external device (e.g. surveillance camera) is required. Ensure the GE2 WAN port has been configured to permit an attached external device during the configuration process. When making connections using these ports, a properly rated RJ45 connector is required. One weatherproof RJ45 plug kit is provided with each access point. When connecting cables to the AP 7161 Ethernet ports, follow the instructions in the connector packaging and tighten the connectors to create a weatherproof seal. Shielded cables are required. AP 7161 Grounding Screw The grounding screw is located to the right of the GE1/POE port and above the GND symbol. WARNING! The grounding cable for an AP 7161 must be at a minimum a #10 gauge wire cross section. The grounding cable can be attached to the unit using one of three recommended methods. Using an 8mm socket and driver: • Loosen the grounding screw and insert the grounding cable into the hole below it. Tighten the grounding screw to 30 inch pounds (lbf-in). • Loosen the grounding screw and wind the grounding cable around the screw. Tighten the grounding screw to 30 inch pounds (lbf-in). • Attach a ring lug to the grounding cable and remove the grounding screw to attach the ring lug to the access point. Secure it to the unit by reinserting the grounding screw. Tighten the grounding screw to 30 inch pounds (lbf-in).
18 AP 7161 Access Point Installation Guide AP 7161 Factory Reset Hardware Button An AP 7161 can be physically reset using the factory reset hardware button. The button is located inside the reset port on the bottom of the unit. NOTE This option is not supported by all AP 7161 software releases. Refer to the release notes for the appropriate software. The reset button is only enabled for a ten second interval as the unit boots up. It can be accessed by removing the cover screw using a ratchet driver and a #2 Phillips head adapter. Push the button to reset the access point. Confirm that the reset cycle was completed and replace the cover screw. To perform an external hardware reset and restore the access point default settings: 1. Using a #2 phillips screwdriver, remove the cover screw from the external reset port. 2. Gently press and hold the reset button. 3. If any of LEDs 2 through 6 are active, it indicates that the unit has booted successfully and the operational software is running. LED Indicators The AP 7161 access point has six LEDs on the top of the access point housing. The access point utilizes two different colored lights below each LED. Only one light displays within an LED at any given time. Every light within each LED is exercised during startup to allow the user to see if an LED is not functioning. The LEDs turn on and off while rotating in a circular pattern. Since two LEDs feed each light pipe, the pattern is from left to right (LEDs 1 through 6), then right to left (LEDs 6 through 1).
AP 7161 Access Point Installation Guide 19 The top housing LEDs have the following display patterns and functionality: Two Radio LEDs A two radio model access point (P/N AP-7161-66040-US and AP-7161-66040-WR) has the following unique LED behavior: LED 1 (Sensor) LED 2 (2.4 GHz) LED 3 (5 GHz) LED 4 (GE2/WAN) LED 5 (GE1/LAN) LED 6 (System) Not Used Blinking Emerald indicates 802.11b/g/n activity. Solid Emerald indicates a radio is present but not configured. Blinking Amber indicates 802.11a/n activity. Solid Amber indicates a radio is present but not configured. LED Off indicates the port is not connected. Blinking Green indicates normal operation. Rapidly blinking Yellow indicates a port error. LED Off indicates the port is not connected. Blinking Green indicates normal operation. Rapidly blinking Yellow indicates a port error. Solid Red indicates diagnostic mode. Blinking Red at 1 second interval indicates POST failure. Solid White following diagnostic mode indicates booting. Blinking Red and White at 1 second interval indicates “no adoption”. Solid White indicates normal operation. WARNING! If LED 6 remains blinking Red for longer than 10 minutes, cycle the power to the unit. If the condition persists, contact the Motorola Solutions support center.
20 AP 7161 Access Point Installation Guide Three Radio LEDs A three radio model access point with sensor (P/N AP-7161-66S40-US and AP-7161-66S40-WR) has the following unique LED behavior: LED 1 (Sensor) Blinking Emerald and Amber at 2 second interval indicates a radio is present but not connected to a server. Solid Amber indicates a radio is present and connected to a server. LED 2 (2.4 GHz) Blinking Emerald indicates 802.11b/g/n activity. Solid Emerald indicates a radio is present but not configured. LED 3 (5 GHz) Blinking Amber indicates 802.11a/n activity. Solid Amber indicates a radio is present but not configured. LED 4 (GE2/WAN) LED Off indicates the port is not connected. Blinking Green indicates normal operation. Rapidly blinking Yellow indicates a port error. LED 5 (GE1/LAN) LED Off indicates the port is not connected. Blinking Green indicates normal operation. Rapidly blinking Yellow indicates a port error. LED 6 (System) Solid Red indicates diagnostic mode. Blinking Red at 1 second interval indicates POST failure. Solid White following diagnostic mode indicates booting. Blinking Red and White at 1 second interval indicates “no adoption”. Solid White indicates normal operation.
AP 7161 Access Point Installation Guide 21 AP 7161 Hardware Mounting and Installation It is recommended to use the AP 7161 mounting bracket kit (KT-147407-01) for most deployments. When a standoff distance is required for a pole mounted or wall mounted installation, use the extension arm kit (KT-150173-01). The following sections detail the installation procedure for deploying an AP 7161 access point: Mounting Bracket Kit The AP 7161 mounting bracket kit (KT-147407-01) includes the Access Point Bracket (left), Angle Adapter Bracket (center), and Pole Mount Bracket (right) sections: The Access Point Bracket and the Angle Adapter Bracket can be adjusted to rotate (plus or minus 15 degrees) and tilt (up to 45 degrees) during installation to orient the unit for optimal positioning. The following ancillary hardware to assemble the mounting bracket sections is included in the kit: Description Quantity M6 serrated hex flanged screws 8 1/2 inch hex head nut 2 1/2 inch x 3/4 inch hex head bolt 2
22 AP 7161 Access Point Installation Guide A torque wrench or ratchet with a 10mm adapter, or an adjustable wrench can be used to assemble the mounting brackets. A finished assembly of the mounting bracket kit is shown below. Assembly during deployment may differ to achieve the required angle and rotation for optimal positioning. Extension Arm Kit When mounting an AP 7161 on poles more than 3 inches in diameter, use the extension arm kit (KT-150173-01) to provide a minimum standoff distance of twelve inches to avoid interference with the antennas.
AP 7161 Access Point Installation Guide 23 The extension arm kit can also be used in combination with the any of the brackets from the mounting bracket kit: The following ancillary hardware to attach the extension arm to the mounting bracket kit sections is included in the extension arm kit: Description Quantity 1/2 inch hex head nut 2 1/2 inch x 3/4 inch hex head bolt 2
24 AP 7161 Access Point Installation Guide Pole Mounted Installations The mounting hardware kit and extension arm can be used in various combinations to properly install the AP 7161 on a pole. For poles of up to 3 inches in diameter, attach the pole mount bracket of the mounting hardware kit at the desired position on the pole using band clamps up to 3/4 inch width, or a 1/2 inch x 4 inch wide U-bolt and nuts. For poles greater than 3 inches in diameter, attach the pole mount bracket using band clamps. CAUTION Always mount the AP 7161 with the black gore vent facing down. NOTE The U-bolt and band clamps are not included in the mounting bracket kit. NOTE Use of the extension arm is recommended for installations on poles greater than 3 inches in diameter.
AP 7161 Access Point Installation Guide 25 Vertical Pole Mount Use the following procedures for vertical pole mount installations. Use of the extension arm is recommended when mounting the access point to poles greater than 3 inches is diameter. For poles up to 3 inches in diameter when using a U-bolt: 1. Thread the two inner nuts onto the U-bolt. Place the U-bolt at the desired mounting location. 2. Place the pole mount bracket section on the U bolt. Adjust the inner nuts until the pole mount bracket section is against the pole and the U-bolt can be secured tightly to the pole. 3. Place the angle adapter bracket section on the U-bolt with the open slot connections on the bottom and align it with the pole mount section. 4. Put the two outer nuts on the U-bolt to attach the angle adapter bracket section to the pole mount bracket section. 5. Tighten all nuts to 300 inch pounds (lbf-in). 6. Position the access point bracket section so that the bottom of the section with the straight (not bevel cut) side is oriented toward the bottom side of the AP with the gore vent. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach (but don’t tighten) the access point bracket section to the AP 7161 with the with four M6 hex flange screws. 7. Insert two M6 hex flange screws into the bottom holes on the sides of the access point bracket section. 8. With the access point positioned so that the gore vent is facing down, insert the two M6 hex flange screws in the bottom holes on the sides of the access point bracket section into the open slot connections on the bottom of the angle adapter bracket section. 9. Rotate the access point bracket section upward and align the top holes on the sides with the top holes on the angle adapter bracket section. Insert two M6 hex flange screws into the top holes on the angle adapter bracket section. 10.Use a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, to finish attaching the access point bracket section to the angle adapter bracket section with the M6 hex flange screws in the open slot
26 AP 7161 Access Point Installation Guide connections and the top holes on the angle adapter bracket section. Do not tighten the screws until all rotation and tilt adjustments are complete. 11.To adjust the position of the access point, rotate the access point bracket section (plus or minus 15 degrees) and tilt the angle adapter bracket section (up to 45 degrees). 12.Tighten all hex flange screws to 60 inch pounds (lbf-in). For mounting with band clamps: 1. Attach the pole mount bracket section at the desired mounting location using band clamps. 2. With the angle adapter bracket section positioned so that the open connector slots are on the bottom, attach the angle adapter bracket section to the pole mount bracket section using two 1/2 inch bolts and nuts. Tighten the nuts to 300 inch pounds (lbf-in). 3. Position the access point bracket section so that the bottom of the section with the straight (not bevel cut) sides is oriented toward the bottom side of the AP with the gore vent. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach (but don’t tighten) the access point bracket section to the AP 7161 with the with four M6 hex flange screws.
AP 7161 Access Point Installation Guide 27 4. Insert two M6 hex flange screws into the bottom holes on the sides of the access point bracket section. 5. With the access point positioned so that the gore vent is facing down, insert the two M6 hex flange screws in the bottom holes on the sides of the access point bracket section into the open slot connections on the bottom of the angle adapter bracket section. 6. Rotate the access point bracket section upward and align the top holes on the sides with the top holes on the angle adapter bracket section. Insert two M6 hex flange screws into the top holes on the angle adapter bracket section. 7. Use a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, to finish attaching the access point bracket section to the angle adapter bracket section with the M6 hex flange screws in the open slot connections and the top holes on the angle adapter bracket section. Do not tighten the screws until all rotation and tilt adjustments are complete. 8. To adjust the position of the access point, rotate the access point bracket section (plus or minus 15 degrees) and tilt the angle adapter bracket section (up to 45 degrees). 9. Tighten all hex flange screws to 60 inch pounds (lbf-in). To use the extension arm with the mounting hardware kit: 1. Attach the pole mount section at the desired mounting location using a U-bolt or band clamps. 2. Complete the steps for assembling and positioning the mounting bracket sections for poles less than or greater than 3 inches outlined above. 3. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach the extension arm to the access point bracket section with four M6 hex flange screws. Tighten the hex flange screws to 60 inch pounds (lbf-in). 4. With the access point positioned so that the gore vent is facing down, attach the extension arm to the access point with four M6 hex flange screws. Tighten the hex flange screws to 60 inch pounds (lbf-in).
28 AP 7161 Access Point Installation Guide Examples for using the extension arm alone, or with the mounting bracket kit for a pole mount installation are shown below: Wall Mounted Installations For wall mounted installations, use only the access point bracket and angle adjust bracket sections. CAUTION Always mount the AP 7161 with the black gore vent facing down. NOTE The U-bolt and band clamps are not included in the mounting bracket kit. NOTE The lag bolts are not included in the mounting bracket kit. 1. With the open slot connections facing down, attach the angle adjust bracket section at the desired mounting location using four #10/32 lag bolts.
AP 7161 Access Point Installation Guide 29 2. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach (but don’t tighten) the access point bracket section to the AP 7161 with four M6 hex flange screws and insert two M6 hex flange screws into the bottom holes on the sides of the access point bracket section. 3. With the access point positioned so that the gore vent is facing down, insert the two M6 hex flange screws in the bottom holes on the sides of the access point bracket section into the open slot connections on the bottom of the angle adapter bracket section. 4. Rotate the access point bracket section upward and align the top holes on the sides with the top holes on the angle adapter bracket section. Insert two M6 hex flange screws into the top holes on the angle adapter bracket section. 5. Use a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, to finish attaching the angle adapter bracket section to the access point bracket section with the four M6 hex flange screws in the open slot connections and the top holes on the angle adapter bracket section. Do not tighten the screws until all rotation and tilt adjustments are complete 6. To adjust the position of the access point, rotate the access point bracket section (plus or minus 15 degrees) and tilt the angle adapter bracket section (up to 45 degrees). 7. Tighten all hex flange screws to 60 inch pounds (lbf-in).
30 AP 7161 Access Point Installation Guide To use only the extension arm: 1. Using four #10/32 lag bolts, attach the extension arm at the desired mounting location. 2. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach the mounting extension arm to the access point with four M6 hex flange screws. Tighten the hex flange screws to 60 inch pounds (lbf-in). To use the extension arm with the mounting hardware kit: 1. With the open slot connections facing down, attach the angle adjust bracket section at the desired mounting location using four #10/32 lag bolts. 2. Complete the steps for assembling and positioning the angle adapter bracket and access point bracket sections outlined above. 3. With the access point positioned so that the gore vent is facing down, attach the extension arm to the access point bracket section of the assembled mounting bracket already in position using four M6 hex flange screws. Tighten the hex flange screws to 60 inch pounds (lbf-in). 4. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach the extension arm to the access point with four M6 hex flange screws. Tighten the hex flange screws to 60 inch pounds (lbf-in).
AP 7161 Access Point Installation Guide 31 AP 7161 Power Options Using Power over Ethernet (PoE) Power over Ethernet (PoE) is the power source for an AP 7161 access point. For optimal performance, an AP 7161 can be powered by the following Motorola Solutions injectors and RFS controllers that support 802.AT PoE. For installations requiring an outdoor PoE injector, the following Motorola Solutions options are recommended: • AP-PSBIAS-7161-US • AP-PSBIAS-7161-WW The AP-PSBIAS-7161 is a 1-Port 802.3at PoE Gigabit Ethernet injector. The injector is IP66 rated for outdoor deployments when used with the weatherproof kit supplied. There are two power cord options for the AP-PSBIAS-7161 models. The AP-PSBIAS-7161-US comes equipped with a cable with a standard three prong power plug. This plug can be removed by the installer if required when connecting to an AC source. The AP-PSBIAS-7161-WW comes equipped with a cable with open leads. Mounting kits are not supplied (see Outdoor PoE Hardware and Mounting Accessories on page 9 for mounting kit part numbers). NOTE Product installation and mounting instructions are provided with the outdoor power injector. Refer to the AP-PSBIAS-7161 Install Guide. If located within 100 meters of the controller and a PoE port is available, the AP 7161 access point can also be connected directly to one of the following Motorola Solutions controllers: • RFS4000 • RFS6000 • RFS7000 • NX9000 A standard CAT5E cable can be used to provide the connection to the AP 7161. The GE1/POE port on the AP 7161 is where the standard CAT5E cable will connect to the access point and use of the weatherproof RJ45 plug kit that comes with the unit will maintain a weatherproof seal for outdoor installation at the ethernet port. If a CAT5E cable is used to connect the access point to an RFS controller through a building egress, a suitable lightning protection system should be considered. A professional installer should be consulted to identify an appropriate system. CAUTION When using controllers, the total power limits for the AP 7161 must be considered. The two radio configuration draws less power than a three radio configuration. If sufficient power is not available, the AP 7161 software will disable the third radio and throttle back performance on all radio and Ethernet interfaces.
32 AP 7161 Access Point Installation Guide Basic AP 7161 Configuration For information on how use a Motorola Solutions RFS Series controller to manage an AP 7161 access point, refer to the Motorola Solutions WiNG 5 Access Point System Reference Guide at http://supportcentral.motorola.com. NOTE Only a trained installation professional should configure the AP 7161. For FCC and ETSI requirements, set the 2.4GHz radio gain to 8 dBi and set the 5GHz radio gain to 10 dBi. The configuration steps below apply to radio1, radio2 and, optionally, radio3. Access Point Location Configuration Select outdoor or indoor placement of the transmitting antennas ap71xx-XXXXXX (config-device-xx-xx-xx-xx-xx-xx-if-radio1)#placement outdoor Note all indoor-only bands are disabled by the software OR ap71xx-XXXXXX (config-device-xx-xx-xx-xx-xx-xx-if-radio1)#placement indoor Note all outdoor-only bands are disabled by the software Antenna Configuration For the AP 7161 to operate properly, the antenna type and antenna gain must be configured. Select antenna type with following command: ap71xx-XXXXXX (config-device-xx-xx-xx-xx-xx-xx-if-radio1)#service antenna-type ap7161-dipole Select antenna gain with following command: ap71xx-XXXXXX (config-device-xx-xx-xx-xx-xx-xx-if-radio1)# antenna-gain <units in dBi> These changes can also be made in the device profile configuration file. Radio Channel and Power Configuration ap71xx-XXXXXX (config-device-xx-xx-xx-xx-xx-xx-if-radio2)#channel <number> ap71xx-XXXXXX (config-device-xx-xx-xx-xx-xx-xx-if-radio2)#power <units in dBm> Only channels and power settings available in your regulatory domain and configuration will be allowed. Automatic Channel Select Override Under certain conditions (e.g. the presence of a 40 MHz channel intolerant client or a legacy device on the extension channel), a radio which has been configured for 40 MHz channel operation may automatically select the 20 MHz channel. To override or restore automatic channel selection, use the following commands: ap71xx-XXXXXX (config-device-xx-xx-xx-xx-xx-xx-if-radio1)#service ignore-ch-width-mgmt ap71xx-XXXXXX (config-device-xx-xx-xx-xx-xx-xx-if-radio1)#no service ignore-ch-width-mgmt This change can also be made in the device profile configuration file.
AP 7161 Access Point Installation Guide 33 Specifications Hardware Specifications Operating Voltage 36-57 VDC Operating Current Not to exceed 750 mA@48 VDC Power In (PoE) PoE support inbound power - 802.3AT on GE1/POE port Ethernet Ports 2 Gigabit Ethernet ports Dimensions (unit) mounted 28.1cm W x 21.8cx H x 9.4cm D (11.1" W x 8.6" H x 3.7" D) Weight (Unit) 6.4 lbs / 2.9 Kg Mounting Adaptable mounting kit for pole and wall deployments with optional extension arm accessory LED 6 top mounted weatherized LEDs with multifunction read Uplink 2 Gigabit Ethernet Ports (GE1/POE, GE2) autosensing Antenna Connectors Outdoor rated N-Type connectors Console Port Outdoor rated RJ45 console port Hardware Reset External hardware reset button Multi Band Security Sensor Outdoor 24x7 Wireless Intrusion Prevention System (IPS)/Assurance Sensor (SKU AP-7161-66S40-US, AP-7161-66S40-WR)
34 AP 7161 Access Point Installation Guide Environmental Specifications Operating Temperature -40 to +70 degrees celsius Storage Temperature -40 to +85 degrees celsius Operating Humidity 5-95 percent Operating Altitude 8,000 feet Storage Altitude 30,000 feet Electrostatic Discharge EN61000-4-2. Air +/-15kV, Contact +/-8kV Enclosure Outdoor IP67 rated, corrosion resistant enclosure ASTM B117 salt, fog, and rust resistance Wind Ratings 150 mph * (unit bracket measurement) Operational Shock IEC60721-3-4, Class 4M3, MIL STD 810F Operational Vibration IEC60721-3-4, Class 4M3 Radio Specifications Network Standards IEEE 802.11 a/b/g/n, 802.11e, 802.11i, WPA2, WMM, and WMM-UAPSD Supported Data Rates 802.11b/g:1, 2, 5.5, 11, 6, 9, 12, 18, 24, 36, 48 and 54 Mbps 802.11a: 6, 9, 12, 18, 24, 36, 48 and 54 Mbps 802.11n: MCS 0-15 up to 300 Mbps 802.11n Support 3x3 MIMO with 2 spatial streams 20MHz and 40MHz channels supported 300Mbps data rates per radio Packet aggregation (AMSDU,AMPDU) Reduced interframe spacing 802.11 b/g/n Operating frequency 2.4 - 2.483 GHz Maximum EIRP 32 dBm* 802.11 a/n Operating frequency 4.940 GHz - 4.990 GHz and 5.25 GHz - 5.35 GHz and 5.470 GHz - 5.825 GHz Maximum EIRP 34 dBm* *Maximum EIRP may vary based on local standards for the area of deployment.
AP 7161 Access Point Installation Guide 35 Networking and Software Specifications Security Stateful Firewall, IP filtering, NAT, 802.1X, 802.11i WPA2, WPA 24x7 Dual band sensor capabilities * (subject to software license keys and sensor radio SKU) Advanced forensics Connectivity troubleshooting Wireless Intrusion Prevention LiveRF Quality of Service (QoS) WMM, WMM-UAPSD, 802.1p, Diffserv and TOS Routing Layer 3 routing, 802.1q/p, DynDNS, DHCP server/client, BOOTP Client, PPPoE and LLDP Approvals Radio* FCC Title 47, part 15, part 90; EN 301 489-17 EN 301 893, v1.5.1 DFS;EN 300 328 Industry Canada; China SRRC Australia/New Zealand Safety* UL 60950-1, -22; CSA C22.2 No.60950-1-07, -22 CB-IEC 60950 -1, 22; EN 60950-1:2006+ A11:2009 RoHS/WEEE/CMM; CE * For more country specific regulatory information, please contact Motorola Solutions or your authorized partner. Warranty • One (1) year on AP 7161 hardware (accessories not included) • (30) day on accessories • (90) day on software
36 AP 7161 Access Point Installation Guide Basic Troubleshooting Basic troubleshooting recommendations for the AP 7161 access point are listed in the following table: Indication Response LEDs are not lit No power to device: • Verify 802.3at compatible source is connected via PoE • Verify AC source to PoE injector • Unit was configured with LEDs disabled No Ethernet connectivity to this unit No Ethernet connectivity to this unit No wireless connectivity to this unit No wireless connectivity to this unit
AP 7161 Access Point Installation Guide 37 Regulatory Compliance This device is approved under the Symbol Technologies, Inc. brand. Symbol Technologies, Inc. is a wholly owned subsidiary of Motorola Solutions, Inc. (collectively “Motorola”). All Motorola Solutions devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Any changes or modifications to Motorola Solutions equipment, not expressly approved by Motorola Solutions, could void the user's authority to operate the equipment. Local language translations are available at the following website: http://supportcentral.motorola.com Motorola Solutions devices are professionally installed, the Radio Frequency Output Power will not exceed the maximum allowable limit for the country of operation. Antennas: Use only the supplied or an approved replacement antennas. Unauthorized antennas, modifications, or attachments could cause damage and may violate regulations. FCC Approval Statement Federal Communications Commission Office of Engineering and Technology Laboratory Division Interim Plans to Approve UNII Devices Operating in the 5470 - 5725 MHz Band with Radar Detection and DFS Capabilities The FCC, NTIA, FAA and industry are working to resolve interference to Terminal Doppler Weather Radar (TDWR) systems used near airports that has occurred from some outdoor wireless systems operating in the 5470 MHz – 5725 MHz band. These wireless devices are subject to Section 15.407 of our rules and when operating as a master device they are required to implement radar detection and DFS functions. We are continuing our work to develop long-term equipment authorization test procedures that will ensure that the devices comply with our rules that include protecting the TDWR operations. In the interim, the Commission will now allow certification of wireless master devices with radar detection function and with DFS capability, if they meet the following conditions: 1. Devices will not transmit on channels which overlap the 5600 – 5650 MHz band.1 2. Devices intended for outdoor use will be further restricted, as follows: • Devices must be professionally installed when operating in the 5470 – 5725 MHz band.2 • Grantees must provide owners, operators and all such installers with specific instructions in their user’s manual on requirements to avoid interference to TDWRs and information that meets the following instructions: • Any installation of either a master or a client device within 35 km of a TDWR location shall be separated by at least 30 MHz (center-to-center) from the TDWR operating frequency 3, 4, and 5.
38 AP 7161 Access Point Installation Guide 1 The devices subject to the requirements in this KDB can select the initial channel for operation to avoid TDWRs and apply the Uniform Channel Spreading requirements (see FCC 06-96 in ET Docket 03-122 released June 30, 2006) on the remaining available frequency band of operation. All the other test procedures including the test radar patterns remain the same at the present time. A revision to the measurement procedure with modification to the Uniform Channel Spreading requirement and other changes will be released in the future. The Commission will also address the issue of any field upgrade option at that time. 2 The grantee must identify the specific expertise and the training required by the installers for installing these types of devices. 3 In some instances it is possible that a device may be within 35 km of multiple TDWRs. In this case the device must ensure that it avoids operation within 30 MHz for each of the TDWRs. This requirement applies even if the master is outside the 35 km radius but communicates with outdoor clients which may be within the 35 km radius of the TDWRs. 4 The requirement for ensuring 30 MHz frequency separation is based on the best information available to date. If interference is not eliminated, a distance limitation based on line-of-sight from TDWR will need to be used. In addition, devices with bandwidths greater than 20 MHz may require greater frequency separation. • Procedures for the installers and the operators on how to register the devices in the industry-sponsored database with the appropriate information regarding the location and operation of the device and installer information is included.6 • Devices must meet all of the other requirements specified in Section 15.407, and it is prohibited to include configuration controls (e.g. country code settings or other options to modify DFS functions) to change the frequency of operations to any frequency other than those specified on the grant of certification for US operation.7 • All applications for equipment authorization must clearly show compliance with all of the technical requirements under worst case parameters, under user or operator control, based on frame rates, listen/talk ratios and user data transfer conditions. All the devices subject to the DFS requirements must be submitted to the Commission’s Laboratory Division for pre-grant testing and equipment authorization.8 The applicant must ensure that all equipment authorization applications subject to this interim procedure include appropriate attestations that the device has no option to change the DFS parameters and that transmissions are disabled at least in the 5600 – 5650 MHz band. The application must include the user’s manual with the appropriate installation and operations requirements for the installers and operators. We are continuing to evaluate additional measures that may need to be taken to further ensure against interference caused by 5 GHz outdoor wireless systems located near airports. While manufacturers have an obligation to ensure that their equipment complies with FCC rules, and must take steps to ensure their devices are unlikely to cause harmful interference, Section 15.5 of the Commission’s rules also places an obligation on users of devices to avoid causing interference and to correct any interference that may occur.
AP 7161 Access Point Installation Guide 39 We encourage the manufacturers to include information for the users, including the operators and installers, to ensure that they understand that it is incumbent on them to cooperate with manufacturers to implement any changes necessary to facilitate compliance. 5 Devices may be optionally designed not to transmit on channels which overlap 5570 – 5680 MHz instead of requiring installers to perform site-by-site adjustments. In that case it is still required that the devices should be installed professionally and the procedures for registering the device in the industry database should be included in the Users Manual. 6 A voluntary WISPA sponsored database has been developed that allows operators and installers to register the location information of the UNII devices operating outdoors in the 5470 – 5725 MHz band within 35 km of any TDWR location (see http://www.spectrumbridge.com/udia/home.aspx). This database may be used by government agencies in order to expedite resolution of any interference to TDWRs. 7 For example, device software must not have any country code options or software configuration settings which allow an end user to modify the DFS operation or impact the performance of DFS. See KDB 594280. 8 The TCBs are not permitted to approve transmitters with radar detection capabilities. See KDB 628591. 9 The manufacturers may consider taking steps providing clear instructions to operators and installers of devices as to the need to comply with rules for use of the band, guidance on registration of devices and any other processes that are designed to avoid interference. They may use methods that include, but are not limited to, instructions in manuals, notification on product web pages and service bulletins issued for products in the field. TDWR Location Information STATE CITY LONGITUDE LATITUDE FREQUENCY TERRAIN ELEVATION (MSL) [ft] ANTENNA HEIGHT ABOVE TERRAIN [ft] GA ATLANTA W 084 15 44 N 33 38 48 5615 MHz 962 113 IL MCCOOK W 087 51 31 N 41 47 50 5615 MHz 646 97 IL CRESTWOOD W 087 43 47 N 41 39 05 645 MHz 663 113 IN INDIANAPOLIS W 086 26 08 N 39 38 14 5605 MHz 751 97 KS WICHITA W 097 26 48 N 37 30 26 5603 MHz 1270 80 KY COVINGTON W 084 34 48 N 38 53 53 5610 MHz 942 97
40 AP 7161 Access Point Installation Guide STATE CITY LONGITUDE LATITUDE FREQUENCY TERRAIN ELEVATION (MSL) [ft] ANTENNA HEIGHT ABOVE TERRAIN [ft] KY LOUISVILLE W 085 36 38 N 38 02 45 5646 MHz 617 113 LA NEW ORLEANS W 090 24 11 N 30 01 18 5645 MHz 2 97 MA BOSTON W 070 56 01 N 42 09 30 5610 MHz 151 113 MD BRANDYWINE W 076 50 42 N 38 41 43 5635 MHz 233 113 MD BENFIELD W 076 37 48 N 39 05 23 5645 MHz 184 113 MD CLINTON W 076 57 43 N 38 45 32 5615 MHz 249 97 MI DETROIT W 083 30 54 N 42 06 40 5615 MHz 656 113 MN MINNEAPOLIS W 092 55 58 N 44 52 17 5610 MHz 1040 80 MO KANSAS CITY W 094 44 31 N 39 29 55 5605 MHz 1040 64 MO SAINT LOUIS W 090 29 21 N 38 48 20 5610 MHz 551 97 MS DESOTO COUNTY W 089 59 33 N 34 53 45 5610 MHz 371 113 NC CHARLOTTE W 080 53 06 N 35 20 14 5608 MHz 757 113 NC RALEIGH DURHAM W 078 41 50 N 36 00 07 5647 MHz 400 113 NJ WOODBRIDGE W 074 16 13 N 40 35 37 5620 MHz 19 113 NJ PENNSAUKEN W 075 04 12 N 39 56 57 5610 MHz 39 113 NV LAS VEGAS W 115 00 26 N 36 08 37 5645 MHz 1995 64 NY FLOYD BENNETT FIELD W 073 52 49 N 40 35 20 5647 MHz 8 97 OH DAYTON W 084 07 23 N 40 01 19 5640 MHz 922 97 OH CLEVELAND W 082 00 28 N 41 17 23 5645 MHz 817 113 OH COLUMBUS W 082 42 55 N 40 00 20 5605 MHz 1037 113 OK AERO. CTR TDWR #1 W 097 37 31 N 35 24 19 5610 MHz 1285 80
AP 7161 Access Point Installation Guide 41 STATE CITY LONGITUDE LATITUDE FREQUENCY TERRAIN ELEVATION (MSL) [ft] ANTENNA HEIGHT ABOVE TERRAIN [ft] OK AERO. CTR TDWR #2 W 097 37 43 N 35 23 34 5620 MHz 1293 97 OK TULSA W 095 49 34 N 36 04 14 5605 MHz 712 113 OK OKLAHOMA CITY W 097 30 36 N 35 16 34 5603 MHz 1195 64 PA HANOVER W 080 29 10 N 40 30 05 5615 MHz 1266 113 PR SAN JUAN W 066 10 46 N 18 28 26 5610 MHz 59 113 TN NASHVILLE W 086 39 42 N 35 58 47 5605 MHz 722 97 TX HOUSTON INTERCONTL W 095 34 01 N 30 03 54 5605 MHz 154 97 TX PEARLAND W 095 14 30 N 29 30 59 5645 MHz 36 80 TX DALLAS LOVE FIELD TX LEWISDALE DFW W 096 58 06 N 32 55 33 5608 MHz 541 80 W 096 55 05 N 33 03 53 5640 MHz 554 31 UT SALT LAKE CITY W 111 55 47 N 40 58 02 5610 MHz 4219 80 VA LEESBURG W 077 31 46 N 39 05 02 5605 MHz 361 113 WI MILWAUKEE W 088 02 47 N 42 49 10 5603 MHz 820 97113 Wireless Country Approvals Regulatory markings are applied to the device signifying the radio(s) are approved for use in the following countries: United States, Canada, Australia, and Europe. Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at: http://www.motorola.com/doc. Note 1: For 2.4 GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Operation of the device without regulatory approval is illegal.
42 AP 7161 Access Point Installation Guide Health and Safety Recommendations The Federal Communications Commission (FCC) with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. Motorola Solutions products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper operation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits. Warnings for the Use of Wireless Devices Please observe all warning notices with regard to the usage of wireless devices. Potentially Hazardous Atmospheres You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders). Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely affected. RF Exposure Guidelines Safety Information The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. Reduce RF Exposure - Use Properly Only operate the device in accordance with the instructions supplied. Remote and Standalone Antenna Configurations To comply with FCC RF exposure requirements, antennas that are mounted externally at remote locations or operating near users at stand-alone desktop of similar configurations must operate with a minimum separation distance of 28 cm from all persons. Power Supply Use only a power-over Ethernet 802.3at compliant solution. The required power rating is 25.5 Watts. Wireless Devices - Countries Country Selection Select only the country in which you are using the device. Any other selection will make the operation of this device illegal.
AP 7161 Access Point Installation Guide 43 Operation in the US The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is limited by firmware. The FCC requires that the FCC ID label be placed on the outside of the device. If the device is placed in a protective enclosure that requires tools to access, a permanent label with FCC ID must be placed on the exterior of the protective enclosure Radio Frequency Interference Requirements - FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Radio Transmitters (Part 15) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radio Frequency Interference Requirements - Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Devices using the 5.470 – 5.725 GHz band shall not be capable of transmitting in the 5.60-5.65 GHz band in Canada, make sure that Canada is the country selected during setup to ensure compliance. Radio Transmitters This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication.
44 AP 7161 Access Point Installation Guide This device has been designed to operate with the antennas listed in this guide, and having a maximum gain of 8 dBi (2.4 GHz) and 10 dBi (5 GHz) for radios one and two. Antennas not included in this list, or having a gain greater than 8 dBi (2.4 GHz) and 10 dBi (5 GHz) for radios one and two, are prohibited for use with this device. This device has been designed to operate with the antennas listed in this guide, and having a maximum gain of 4.5 dBi (2.4 GHz) and 7.5 dBi (5 GHz) for radio three. Antennas not included in this list, or having a gain greater than 4.5 dBi (2.4 GHz) and 7.5 dBi (5 GHz) for radio three, are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Label Marking: The Term "IC:" before the radio certification signifies that Industry Canada technical specifications were met. This device has been designed to operate with the antennas listed in the Enterprise Wireless LAN Antenna Specification Guide. Refer to the guide at http://supportcentral.motorola.com. CE Marking and European Economic Area (EEA) The use of 2.4 GHz RLAN’s, for use through the EEA, have the following restrictions: • Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz • France outside usage, the equipment is restricted to 2.400-2.45 GHz frequency range. • Italy requires a user license for outside usage Statement of Compliance Motorola Solutions hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from http://www.motorola.com/doc. Other Countries Australia Use of 5 GHz RLAN’s in Australia is restricted in the following band: 5.50 – 5.65 GHz. Brazil Regulatory Declarations for AP 7161 - BRAZIL Note: The certification mark applied to the AP 7161 is for Restrict Radiation Equipment. This equipment operates on a secondary basis and does not have the right for protection against harmful interference from other users including same equipment types. Also this equipment must not cause interference to systems operating on a primary basis. For more information consult the website www.anatel.gov.br
AP 7161 Access Point Installation Guide 45 Declarações Regulamentares para AP 7161 - Brasil Nota: A marca de certificação se aplica ao Transceptor, modelo AP 7161. Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Para maiores informações sobre ANATEL consulte o site: www.anatel.gov.br Chile Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a radiaciones electromagnéticas. This device complies with the Resolution Not 403 of 2008, of the Undersecretary of telecommunications, relating to electromagnetic radiation. Mexico Restrict Frequency Range to: 2.450 – 2.4835 GHz. Taiwan NOTICE! According to: Administrative Regulations on Low Power Radio Waves Radiated Devices Article 12 Without permission granted by the DGT, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low power radio-frequency devices. Article 14 The low power radio-frequency devices shall not influence aircraft security and interfere with legal communications; If found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications are operated in compliance with the Telecommunications Act. The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices.
46 AP 7161 Access Point Installation Guide Wireless device operates in the frequency band of 5.25-5.35 GHz, limited for indoor use only. 在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用
AP 7161 Ace ess Point I nsta II ation Guide 47 1[ Waste Electrical and Electronic WEEE English: For EU Customers: All products at the end or their tile must be returned to Motorola for recycling. For information on how to return product,please go to: http://www.symbol.com/erwironmental_compliance. Bulgallsh:3a Kll"C>rrH OT EC: CnoA pa• Ha nonc3""" MM >K«OOT BCOIY K" npoAYKT" Tp•6ua Aa ce BPbiJiaT Ha Motorola 3a pe[IHKilMpaHe. 3a l1Hr:j)OpMa[ll1OTHOCHO BPbiJiaHeTO Ha npOAYKTI1, MOnSOT>1AeTe Ha aApec:http://www.symbot.com/weeetink. tei1fna: Pro zakazniky z EU:Vsechny produkty je nutne po skoncenf jejich zivotnosti vralit spotecnosti Motorola k recyktaci. tnformace o zpusobu vraceni produktu najdete na webove strance: http://www.symbot.com/cnvironmcntat_compit anco. Danek: Tit kunder iEU: A tte produkter skat relurnereslit Motorolalit recirkutering, nar de er udtjent. L<es optysningerne om returnering at produkter p\;:hltp:/!www.symbot.com/ environmental_compliance. Deulldl; Fur Kundeninnerhalb der EU: Aile Produkte mussen am Ende i hrer Lebensdauer zum Recycling an Motorola zuri)ckgcsandt worden. Informationen zur Rilcksendung von Produkten inden Sie unter http://www.symbot.com/environmental_compliance. Eeatl: EL klientidclc:koik tooted tulcb ncndc cluca loppcdes tagastada taaskasutamise eesmargil Motorolai'le. Lisainformatsioonisaamiseks toote tagastamise kohta klilastage palun aadressi: hl tp://www.syrnbol.com/environrnental_cornpliance. Espallol: l"ara clientes en Ia Union Europea: todos los productos deben\n entregarse a Motorola at final de su ciclo de vida para que sean reciclados. Si desea mas informacion sobre como dovolvcr un producto,visito:htlp://www.symbol.com/cnvironmcntat_compliance. EM, rK6!rl<l mAurr.<; OTI]V E. E.: 0Aa TU npo'i6VTO, OTO rtAo<; Tl]<; 61irpKtiU<;W <; TOU<;, nptml vo tTTIOTPt<POVTOI OTI]V Motorola VIO OVOKUK Moq. r,a TTtPIOOCIT£Pt<; nl\qpO<POPit<; oxcnKat rqv cmorpo<Ptv6<; npoi'6VTo<;,cmoKt<P9dTt rq o1cuauvol] http://www.symbol.com/environmental_compliance mo C.u:roiKruo. Fl811981s : Clients de !'Union Europeenne : Tous les produi s en fin de cycle de vie doivent etre retournes il Motorola pour recyclage. I"our cle plus ampies informations sur le retour de produits,consultez : http:/r\w..w.symbol.com/environmental_oompliance. Italiano:per i clienti deii'UE: tutli i prodolli che sono giunti at termine del rispettivo ciclo di vita devono essere restituiti a Motorola al fine di consentirne il riciclaggio. Per informazioni sulle modalila di rest!uzione,vlsilare il seguente silo Web: http://www.symbol.com/ environmental_compliance. Latvletu: ES klientiem: visi produktipee to kalposanas miiza beigamir janogiida atpakal Motorola otrreizejaiparstd;idei. Lai iegutu informaciju par produktu nogadiiilanu Motorola, lliclzu, skat et: http://www.symbol.com/environmental_compliance.
48 AP 7161 Ace ess Point I nsta II ation Guide Lletuvt t= ES vartotojams: visigaminiai, pasibaigusill eksploatacijos laikui, turi bOti grzinti utilizuoti i kompanij<t Motorola". Daugiau infom acijos,kaip grq:Zinti gamin,i rasite: htlp://www.symbol.com/cnvlronmonlal_compliance. Magyar: Az EU-ban vasar16knak: Minden tonkremenlterm<lket a Motorola vallalathoz kcll eljuttatni (rjrahasznositas celjab61. A termek visszajuttatasanak m6djaval kapcsolatos tudnival6kertlatogasson el a hllp://www.syrnbol.com/environmental_cornpliance weboldalra. Mall: Gi1al klijenti11-UE: il-prodotti kollha li jkunu waslu fl-alinar tal-najja ta'1-uzu taglihom, iridu jigu rritornati gnand Motorola ghar-riciklagg. Ghal aktar taghrif dwar kif ghandek tirritorna 1-prodoll, jekk jogT1gbok :Zur:hllp://www.symbol.cornlcnvironmcnlal_cornpliancc. Nedeflanda: Voor klanten in de EU:aile producten dienen aan het eincle van hun levensduur naar Motorola te worden teruggezonden voor recycling. Raadpleeg htlp://www.symbol.com/ environmental_compliance voor meer informatie over het l erugzenden van producten. Polski:Klienci z obszaru UniiEuropejskiej:Produkty wycofane z eksploatacjinalei:y zwr6cic do finny Motorola w c·elu ich utylizacji. Infonnacje na ternat zwrotu produkt6w znajdujq sina stronic internctowcj http://www.symbol.com/cnvironrncntal_compliancc. pPara clientes da UE: todos OS produtos no fim de vida devem ser devolvidos a Motorola para reciclagern. Para obter inforrnao;6es sobre como devolver o produto,visite: htlp://www.syrnbol.com/cnvironmental_complianco. RomAnesc: Pentru clienidin UE: Toate produsele,la staritul duratei lor de func\ionare, trebuie rcturnatc Ia Motorola pcntru rcciclare. Pcntruinforma ii despre rcturnarea produsului, accesa\i: hNp:/!Y.ww.symbol.corn/weeelink. Slovensld:Za kupce v EU: vsi izdelki se morajo po poteku Zivljenjske dobe vrnitipodjetju Motorola za reciklazo. Zainforrnacije o vraciluizdelka obiscite: http://WY.w.syrnbol.com/ environmental_compliance. SlclveOOtna: Pre zakaznfkov z krajin EU: Vsctky vyrobky musia byl' po uplynutf doby ich zivotnosti vratene spolocnostiMotorola na recyklaciu.Blizsie infonnacie o vrateni vyrobkov nirjdete na: http://Y,ww.symbol.G'Orn/environmental_compliance. Suomi: Asiakknat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierratettavnksi Motorola-yhtioon,kun tuotetta ei enaa kayteta. Lisatietoja tuotteen palauttarnisesta on osoiNeessa http://www.symbol.com/environmental_compliance. Svenska: For kunder inom EU: Alia produkter som uppn<\tt sin livslangd m;\ste returnems till Motorola for atervinning. Information om hur du returnerar produkten finns pa http://www.symbol.com/environmcntal_compliancc.
AP 7161 Access Point Installation Guide 49 Motorola Solutions Support Center If you have a problem with your equipment, contact Motorola Solutions Support for your region. Support and issue resolution is provided for products under warranty or that are covered by an Motorola Solutions Support agreement. Contact information and web self-service is available by visiting http://motorolasolutions.com/support. When contacting Motorola Solutions support, please provide the following information: • Serial number of the unit • Model number or product name • Software type and version number Motorola Solutions responds to calls by e-mail, telephone, or fax within the time limits set forth in support agreements. If you purchased your product from a Motorola Solutions business partner, contact that business partner for support. Customer Support Web Sites The Motorola Solutions Support Central Web site, located at http://supportcentral.motorola.com/ provides information and online assistance including developer tools, software downloads, product manuals and online repair requests. Manuals http://supportcentral.motorola.com General Information Obtain additional information by contacting Motorola Solutions at: Telephone (North America): 1-800-722-6234 Telephone (International): +1-631-738-5200 Website: http://www.motorolasolutions.com
50 AP 7161 Access Point Installation Guide AP 7161 Series RoHS Compliance 部件名称 (Parts) 有毒有害物质或元素 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr6+) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 金属部件 (Metal Parts) X O O O O O 电路模块 (Circuit Modules) X O O O O O 电缆及电缆组件 (Cables and Cable Assemblies) X O O O O O 塑料和聚合物部件 (Plastic and Polymeric Parts) O O O O O O 光学和光学组件 (Optics and Optical Components) O O O O O O 电池 (Batteries) O O O O O O O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。 对销售之日的所售产品，本表表示，公司供应链的电子信息产品可能包含这些物质。注意：在所售产品中可能会 也可能不会含有所有所列的部件。 This table was created to comply with China RoHS requirements for the Motorola Solutions AP 7161 model access point.
AP 7161 Access Point Installation Guide 51
Motorola Solutions, Inc. 1301 E. Algonquin Rd. Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2012 Motorola Solutions, Inc. All Rights Reserved. 72-165267-01 Revision A-4 November 2012

Navigation menu