ZTE ZXR10W800A Wireless Access Point User Manual Professional Installation Manual
ZTE Corporation Wireless Access Point Professional Installation Manual
ZTE >
Contents
- 1. Usera Manal
- 2. Professional Installation Manual
- 3. Users Manual
Professional Installation Manual
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual ZTE CORPORATION](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-1.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual Manual Version 20040306-R1.0 Product Version V2.0 BOM ×××××××× Copyright © 2003 ZTE Corporation All rights reserved. No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any means without the prior written permission of ZTE Corporation. ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China Website: http://www.zte.com.cn Post code: 518057 Customer Support Center: (+86755) 26770800 800-830-1118 Fax: (+86755) 26770801 E-mail: 800@zte.com.cn * * * * S.N.: DDDDDDDDD](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-2.png)
![FAX: +86-755-26770160 Suggestions and Feedback To improve the quality of ZTE product documentation and offer better services to our customers, we hope you can give us your suggestions and comments on our documentation and fax this form to 0086-755-26770160; or mail to “ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China”. Our postcode is 518057. Document Name ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point User’s Manual Product version V2.0 Document version 20040306-R1.0 Equipment installation time Your information Name Company Postcode Company address Telephone E-mail Good Fair Average Poor Bad Overall Instructiveness Index Correctness Completeness Structure Illustration Your evaluation of this documentation Readability Overall Instructiveness Index Correctness Completeness Structure Illustration Your suggestion on the improvement of this documentation Readability Your other suggestions on ZTE product documentation](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-3.png)
![Preface About This Manual This manual, ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point — User’s Manual, is applicable to W800A wireless access point (W800A for short) of the ZXR10 WAS (V2.0) IP wireless access system. The ZXR10 WAS IP wireless access system is the IP wireless access system developed by ZTE. It consists of a series of wireless access network products, such as wireless network card, wireless access point (AP) and DSL 2-in-1 wireless router. Serving as the operation guide to W800A, this manual introduces the function features, installation, operation, using and maintenance of W800A. This manual consists of 7 chapters and 2 appendixes. Chapter 1, Safety Precautions, introduces the safety precautions of this product and safety symbols used in this manual. Chapter 2, Installation and Debugging, deals with the installation and debugging methods of W800A. Chapter 3, Command Line Configuration, covers the command line configurations of W800A. Appendix B, Making of Ethernet cables, details the power supply mode of W800A Ethernet and making of Ethernet cables. Conventions Four striking symbols are used throughout this manual to emphasize important and critical information during operation: Attention, Caution, Warning and Danger: alerting you to pay attention to something.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-5.png)
![Statement: The actual product may differ from what is described in this manual due to frequent update of ZTE products and fast development of technologies. Please contact the local ZTE office for the latest updating information of the product. Warning This instruction manual only apply to W800A with the following antennas: TQJ-5800BKF40-W, TQJ-5800C-5, TQJ-5800BKF8, R0322-025](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-6.png)
![-i-Contents 1 Safety Precautions...................................................................................................................1-1 1.1 Safety Precautions .............................................................................................................1-1 1.2 Symbol Description ...........................................................................................................1-2 2 Installation and Debugging.......................................................................................................2-1 2.1 Installation Preparations .....................................................................................................2-1 2.1.1 Installation Preparation Flow.......................................................................................2-1 2.1.2 Tool, Instrument and Document...................................................................................2-3 2.1.3 Installation Environment Inspection.............................................................................2-4 2.1.4 Unpacking Inspection.................................................................................................2-4 2.2 Installation........................................................................................................................2-4 2.3 Power-on and Power-off.....................................................................................................2-6 2.4 Debugging........................................................................................................................2-6 3 Command Line Configuration..................................................................................................3-1 3.1 Overview..........................................................................................................................3-1 3.2 User Mode........................................................................................................................3-4 3.2.1 Entering the Privileged Mode......................................................................................3-4 3.2.2 Exiting the Telnet Configuration..................................................................................3-4 3.3 Privileged Mode................................................................................................................3-5 3.3.1 Network Connectivity Check......................................................................................3-5 3.3.2 Saving the Configuration Data to FLASH.....................................................................3-5 3.3.3 Restoring the Default Configuration.............................................................................3-5 3.3.4 Resetting the Software................................................................................................3-6 3.3.5 Entering the Configure Mode......................................................................................3-6](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-7.png)
![-ii-3.3.6 Exiting the Privileged Mode.......................................................................................3-6 3.3.7 Exiting the Telnet Configuration .................................................................................3-6 3.4 Configure Mode................................................................................................................3-6 3.4.1 Bridge Configuration.................................................................................................3-7 3.4.2 Clearing the Information............................................................................................3-7 3.4.3 Configuring the Configuration Server ..........................................................................3-8 3.4.4 DHCP Server Configuration .......................................................................................3-8 3.4.5 DISCOVER Configuration....................................................................................... 3-10 3.4.6 802.1X Parameter Configuration................................................................................3-11 3.4.7 Password Configuration in the Privileged Mode.......................................................... 3-14 3.4.8 Erasing the Filtration Rules ...................................................................................... 3-14 3.4.9 Exiting the Configure Mode ..................................................................................... 3-14 3.4.10 IAPP Load Balance Configuration ........................................................................... 3-15 3.4.11 Entering the Interface Configuration Mode ............................................................... 3-16 3.4.12 IP Network Parameter Configuration ....................................................................... 3-17 3.4.13 Kicking Users....................................................................................................... 3-18 3.4.14 Two-Layer Separation Configuration ....................................................................... 3-18 3.4.15 Log Printing Message Configuration........................................................................ 3-19 3.4.16 MAC Filtration Configuration................................................................................. 3-20 3.4.17 MAC Address Authentication Configuration ............................................................. 3-21 3.4.18 Manager Configuration .......................................................................................... 3-21 3.4.19 QoS Configuration ................................................................................................ 3-22 3.4.20 RADIUS Server Configuration................................................................................ 3-22 3.4.21 SNMP Module Configuration.................................................................................. 3-24 3.4.22 SSH Parameter Configuration ................................................................................. 3-28 3.4.23 Spanning Tree Parameter Configuration ................................................................... 3-29](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-8.png)
![-iii-3.4.24 TELNET Configuration ..........................................................................................3-32 3.4.25 Uploading/Downloading TFTP Files ........................................................................3-32 3.4.26 VLAN Configuration..............................................................................................3-33 3.4.27 Web Configuration.................................................................................................3-34 3.4.28 Nation Zone Configuration......................................................................................3-34 3.4.29 Showing Parameter Configuration............................................................................3-35 3.5 Ethernet Interface Configuration Mode...............................................................................3-41 3.5.1 Exiting the Ethernet Interface Configuration Mode ......................................................3-42 3.5.2 Ethernet Interface MAC Filtration Configuration .........................................................3-42 3.6 Wireless Interface Configuration Mode ..............................................................................3-42 3.6.1 802.11-Related Parameter Configuration of the Wireless Interface.................................3-42 3.6.2 ESSID Hiding Configuration.....................................................................................3-45 3.6.3 Exiting the Wireless Interface Configuration Mode ......................................................3-46 3.6.4 Enabling the Link Integrity Detection Function ...........................................................3-46 3.6.5 Wireless Interface MAC Filtration Configuration.........................................................3-46 3.6.6 Multi-ESSID Configuration ......................................................................................3-46 3.6.7 Security Parameter Configuration ..............................................................................3-47 3.6.8 Transmission Power Configuration ............................................................................3-49 3.6.9 Working Mode Configuration....................................................................................3-49 A.1 Making of Ethernet Cables....................................................................................................1 A.1.1 Making of Straight Through Ethernet Cables (RJ45).........................................................1 A.1.2 Making of Straight Through Power Supply Ethernet Cables (C-RJ45-001)..........................1 A.1.3 Making of Crossover Ethernet Cables (RJ45J).................................................................2 A.1.4 Ethernet Cable Label....................................................................................................3](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-9.png)
![-i-A List of Figures Fig. 2.1-1 Sub-Channel Distribution........................................................................................2-1 Fig. 2.1-2 Channel Distribution Principle of Adjacent APs.........................................................2-2 Fig. 2.2-1 installation instruction ............................................................................................2-5 Fig. 2.2-2 Soldered Connectors...............................................................................................2-6 Fig. 3.-1 Serial Port Configuration ..........................................................................................3-3 Fig. 3.1-2 Telnet to W800A....................................................................................................3-3 Fig. A.1-1 Label of the Straight Through Ethernet Cable...............................................................3 Fig. A.1-2 Label of the Straight Through Power Supply Ethernet Cable ..........................................3 Fig. A.1-3 Label of the Crossover Ethernet cable .........................................................................4](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-11.png)
![-i-A list of Tables Table 1.2-1 Safety Symbols and Descriptions ...........................................................................1-3 Table 2.1-1 IDs and Frequencies of Channels ...........................................................................2-2 Table 3.6-1 W800A Working Channels..................................................................................3-45 Table A.1-1 Connections of Straight Through Ethernet Cables (RJ45)............................................1 Table A.1-2 Connections of Straight Through Power Supply Ethernet Cables (C-RJ45-001)..............2 Table A.1-3 Connections of Crossover Ethernet Cables (RJ45J).....................................................2](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-13.png)
![1-1 1 Safety Precautions This chapter introduces the safety precautions of this product and safety symbols used in this manual. 1.1 Safety Precautions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference,and(2) this device must accept any interference received, including interference that may cause undesired operation. To assure continued compliance, (example – use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This equipment is with high temperature and voltage, so only the professional](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-15.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 1-2personnel who had passed the training can install, operate and maintain it. ZTE assumes no responsibility for consequences resulting from violation of general specifications for safety operations or of safety rules for design, production and use of equipment. 1.2 Symbol Description See Table 1.2-1 for the safety symbols used in this manual, which serves to remind the readers of the safety precautions to be taken when the equipment is installed, operated and maintained.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-16.png)
![Chapter 1 Safety Precautions 1-3Table 1.2-1 Safety Symbols and Descriptions Safety Symbols Meaning Call for notice Call for antistatic measures Warn against electric shock Caution against scald Warn against laser Caution against microwave Four types of safety levels are available: danger, warning, caution and note. To the right of a safety symbol is the text description of its safety level. Under the symbol is the detailed description about its contents. See the following formats. Danger: Any failure to take the reminder seriously may lead to important accidents, such as casualties or damage to the equipment. Cautions: Any failure to take the reminder seriously may lead to important or severe injury accidents, or damage to the equipment. Caution: Any failure to take the reminder seriously may lead to severe injury accidents or damage to the equipment.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-17.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 1-4 Note: Any failure to take the reminder seriously may lead to injury accidents or damage to the equipment. & Remark, reminder, tip… The remarks, prompt and tips in addition to safety statements.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-18.png)
![2-1 2 Installation and Debugging This chapter details the methods and procedure of installation and debugging of the W800A for your reference. 2.1 Installation Preparations 2.1.1 Installation Preparation Flow Before installing the W800A, the engineering personnel should confirm that such work as solution design, project survey and W800A basic configurations have been completed. Brief introductions to the preparations required for installation are as follows. 2.1.1.1 Channel Planning According to 802.11b wireless LAN international standard and the standard of state radio management committee, the working frequency band of a wireless device in the wireless LAN is 2400 MHz ~ 2483.5 MHz, and the working frequency bandwidth is 83.5 MHz, divided into 14 sub-channels with 22 MHz as the bandwidth for each one. The sub-channel distribution is shown in Fig. 2.1-1. 1 6 112 7 12345 109814132.417 2.427 2.437 2.447 2.4572.412 2.422 2.432 2.442 2.452 2.462 2.472 2.4842.467 Fig. 2.1-1 Sub-Channel Distribution Viewed from the above diagram, up to 13 channels are available. The IDs and central frequencies of these 13 channels are described in Table 2.1-1.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-19.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 2-2Table 2.1-1 IDs and Frequencies of Channels Channel ID Central Frequency Low End/High End Frequency of the Channel 1 2412MHz 2401/2423MHz 2 2417MHz 2411/2433MHz 3 2422MHz 2416/2438MHz 4 2427MHz 2421/2443MHz 5 2432MHz 2426/2448MHz 6 2437MHz 2431/2453MHz 7 2442MHz 2431/2453MHz 8 2447MHz 2436/2458MHz 9 2452MHz 2441/2463MHz 10 2457MHz 2446/2468MHz 11 2462MHz 2451/2473MHz 12 2467MHz 2456/2478MHz 13 2472MHz 2461/2483MHz When multiple channels work at the same time, the central frequency intervals between two channels should not be less than 25 MHz to avoid mutual interference. As shown in Fig. 2.1-1, in a cell, direct spread spectrum technology can support simultaneous work of up to 3 un-overlapped channels. In the wireless LAN planning, to realize efficient coverage of APs and avoid mutual interference between channels, the cellular coverage principle of BTS is adopted in the channel distribution. 3 un-overlapped channels (for example, channels 1, 6 and 11) can be used in the same area at the same time, as shown in Fig. 2.1-1. APchannel 6APchannel 6APchannel 6APchannel 1APchannel 11APchannel 11APchannel 11 Fig. 2.1-2 Channel Distribution Principle of Adjacent APs](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-20.png)
![Chapter 4 Installation and Debugging 2-3When using APs, for the adjacent APs, we will select their working channels (channels 1, 6 and 11 are usually used) according to the principle shown in Fig. 2.1-1, to guarantee the normal work of the wireless LAN. The channel distribution principle of 802.11g standard is the same as that of 802.11b. 802.11a standard channels feature anti-interference performance, so no special configuration is required. In the actual networking, you only need make sure that the channels between adjacent APs are different. 2.1.1.2 Configuration before Installation Before the installation, power on W800As in turn and check whether they can work normally. In the normal case, the Power indicator and ACT indicator on the W800A panel should be always on, and the RUN indicator should flash slowly (about once per second). If the indicator is not in the normal status, you can log on to the W800A in the hyper terminal mode and check whether the version is loaded normally. If necessary, you can reload the version (refer to Section 7.3 Version Loading and Upgrade for detailed procedure). When you make sure that the W800A works normally, it is required to implement basic configurations for it. The configuration contents are as follows: 1. Configuring the W800A IP addresses, that is, management addresses. At least one management address should be configured for each W800A, for the management configuration of W800A. 2. Configuring the wireless working mode of the W800A wireless interface and the SSID (Service ID), using channel and rate of the corresponding wireless interface. The detailed configuration methods will be introduced in the subsequent sections. 2.1.2 Tool, Instrument and Document = One wireless network card. = One PC for configuration management = ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point — User’s Manual](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-21.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 2-42.1.3 Installation Environment Inspection The W800A can only be used indoors. To guarantee the normal work and longer useful life of the equipment, the indoor temperature range should be -5 °C ~ 45 °C, you should maintain good ventilation and dry air indoors, and the relative humidity range is 5% ~ 95%. 2.1.4 Unpacking Inspection Generally, the following equipment and accessories are contained in the package of this product. W800A 1 Power adapter 1 Console configuration cable 1 Delivery attached document CD 1 & Note: Please refer to the packing list in the package. If there is any missing part, please contact ZTE Cooperation. 2.2 Installation W800A shell is made in plastic with certain mechanical intensity, and can satisfy the using requirement. The material is fire-resistant and satisfies the environment protection requirement. The ground bolt can be installed on the interface board of the shell, for grounding. The W800A can be used not only on the desktop or ceiling but also on the wall, so it is easily to be used. The W800A installation process is described in detail as follows: 1. Place the W800A to the proper position according to the engineering planning, for example, evenly place it on the desktop, ceiling or wall. 2. Determine the angle of the antenna. 3. Connect the power cable to the power socket on the W800A backplane. 4. Connect the Ethernet cable to the Ethernet interface on the W800A backplane.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-22.png)
![Chapter 4 Installation and Debugging 2-5 Fig. 2.22-1 installation instruction When the W800A is installed on the ceiling, for the ceiling in plaster or floor, the W800A antenna can be directly installed on the ceiling; for the ceiling in metal, if the antenna is directly installed on the ceiling, the antenna signal will be shielded and W800A can not work normally, so you should lead the antenna to the place under the ceiling, through correct antenna feeder. If the W800A is hanged on the wall, reliable fixing method is necessary. If the W800A is placed on the desktop, reliable fixing method is required to ensure the safety of the equipment. Warning 5. Once the RF antenna connector is screwed onto the W800A, the connectors must be rendered "permanent" and non-disconnectable in accordance with FCC rules. This can be accomplished either by; a) Soldering the connectors together, (see Fig. 2.22-2) or,](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-23.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 2-6 Fig. 2.22-2 Soldered Connectors b) Gluing together by using permanent, fast-setting epoxy glue and surround the entire periphery of the connector junction so it is not possible to disconnect. Follow the directions provided on the glue package for cleaning and mixing the two-part glue together. 2.3 Power-on and Power-off The following two power methods are used for the W800A system. 1. Use the in-house power adapter of the W800A. 2. Use PoE. The terminal PoE module is embedded in the W800A. When PoE power supply is adopted, a standard straight-through cable is used to connect the PoE interface of the PoE source end device W112P or W105P. For the detailed description, refer to Appendix B. To power on the W800A, connect the power adapter or Ethernet cable for powering the Ethernet for the W800A. After being powered on, the W800A will start automatically, without any operation by users. To power off the W800A, directly disconnect the W800A power adapter or the cable for powering Ethernet. 2.4 Debugging After W800A is powered on and started, it is required to implement service debugging. There are three purposes for debugging:](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-24.png)
![Chapter 4 Installation and Debugging 2-71. Ensure that the route between W800A and Internet/customer server is smooth. 2. Ensure that each client in the W800A coverage area can access Internet normally. 3. Ensure that in the whole engineering coverage area, the clients can be roaming switched between the cells containing APs.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-25.png)
![3-1 3 Command Line Configuration This chapter describes the operation methods and configuration commands of the W800A command line configuration. 3.1 Overview The W800A provides the Command Line Interface (CLI) for configuring the W800A data. The CLI configuration of the W800A has the following features: 1. You can not only implement local configuration through the hyper terminal software with the serial port, but also implement local or remote configuration in Telnet with the Ethernet interface and wireless network card. 2. The CLI provides five command modes: User, privileged, configure, Ethernet interface configuration and wireless interface configuration modes. One mode is the execution environment for a group of related commands, and one command can be executed only in the corresponding command mode. To obtain the valid commands in the current command mode, input “?” in the current mode. 3. Commands are of two types: information query and function. The information query commands serve to obtain some information to be queried. The function commands serve to change the function configuration of the W800A. The changed configuration is saved in the running configuration information library. To cancel the function configuration, execute the reverse command of the former command (that is, no + key word + former command) 4. CLI provides perfect help system: At any time, you can input “?” to obtain the related help information. 5. The command inputting provides the fuzzy match function: Once the information input by the user is enough for determining a command, no more information is required to be input. 6. CLI provides the command history function: You can select a historical command for executing through “?” or “?” of the keyboard.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-27.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-27. CLI provides two layers of password protection to reject illegal users. The first layer password authentication appears on the Telnet welcome interface, the safety authentication for accessing the user mode is required at this time. The default user name is “root” and default password is “public”. In the user mode, input the enable command and correct password to enter the privileged mode, the default password is “zte”. & Notes: When you implement the configuration in the serial port mode, you can enter the user mode from the hyper terminal interface directly, without any authentication. 8. CLI can automatically page the output commands on the terminal: “—More—” at the lower left corner of the command output window indicates more output commands. At this time, you can press CTRL to display the next page, press ENTER to output the next line and press other keys to exit. 9. W800A CLI provides the basic command line editing function. The short-cut keys for editing command lines are described as follows: Ctrl + U: Delete the whole command being input. Ctrl + A: Move the cursor to the first character of the command line. Ctrl + E: Move the cursor to the last character of the command line. Ctrl + X: Delete all the characters before the cursor. Ctrl + K: Delete all the characters after the cursor (containing the character at the cursor) Ctrl + C: Give up all the input contents. Enter the new line and the prompt character will appear. When the serial port mode is used for configuring the W800A, the serial port attribute configurations of the hyper terminal are shown in Fig. 3.-1.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-28.png)
![Chapter 5 Command Line Configuration 3-3 Fig. 3.-1 Serial Port Configuration When the Telnet mode is used for configuring the W800A, you just need input “telnet/W800A working IP address”, as shown in Fig. 3.1-2. By default, the W800A working IP address is 192.168.1.254 and the subnet mask is 55.255.255.0. Fig. 3.1-2 Telnet to W800A These five configuration modes of the W800A and all the available commands under each mode are described in detail as follows: The stipulation of command format are as](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-29.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-4follows: 1. abc refers to the command or keyword. 2. <abc> refers to the contents to be input by the user. 3. abc|def indicates that one of the two will be selected. 4. For the contents included in [ ], the user can choose to input or not input them.. 5. For the contents included in { }, the user must input them. 3.2 User Mode Entering mode: Telnet Exiting mode: exit Default prompt character: wlan> Note: After logging on to the W800A in Telnet, the common user can enter the user mode only once the user name and password authentications are passed. The default user name is “root” and default password is “public”. To avoid the case in which the illegal user tries with different passwords, the system will automatically disconnect from the Telnet of a user, after this user inputs wrong password for consecutive three times. 3.2.1 Entering the Privileged Mode Command mode: User mode Function: Input the correct password to enter the privileged mode. Command format: enable Note: After the user inputs the enable command and press ENTER, the system will prompt that password need be input. The default password of privileged mode is “zte”. 3.2.2 Exiting the Telnet Configuration Command mode: User mode. Function: Exiting the user mode and returning to the system. Command format: exit.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-30.png)
![Chapter 5 Command Line Configuration 3-53.3 Privileged Mode Entering mode: Input the enable command in the user mode and input correct password. Exiting mode: disable, entering the user mode; exit, exiting the privileged mode and returning to the system. Default prompt character: wlan # 3.3.1 Network Connectivity Check Command mode: Privileged mode Function: Checking the network connectivity. Command format: ping <A.B.C.D> [-n <echo-number>] [-w <timeout>] [-l <packet-size>] [-t] Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D> IP address Destination IP address -n None Setting the flag bit of ping packet quantity. <echo-number> 1~40 Quantity of ping packets. -w None Setting the flag bit of the maximum time-out interval. <timeout> 1~2 Maximum time-out interval (unit: second). -l None Setting the flag bit of the buffer area capacity . <packet-size> 0~1504 Buffer area capacity -t None Setting the consecutive ping packets (complete it by <Ctrl + C>) 3.3.2 Saving the Configuration Data to FLASH Command mode: Privileged mode. Function: Saving the configuration data to FLASH. Command format: write flash. 3.3.3 Restoring the Default Configuration Command mode: Privileged mode Function: Deleting the database, recovering the default configuration of the W800A](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-31.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-6and reset it. Command format: default enable 3.3.4 Resetting the Software Command mode: Privileged mode Function: Resetting the W800A. Command format: reboot 3.3.5 Entering the Configure Mode Command mode: Privileged mode Function: Entering the configure mode. Command format: configure terminal 3.3.6 Exiting the Privileged Mode Command mode: Privileged mode Function: Exiting the privileged mode and entering the user mode. Command format: disable 3.3.7 Exiting the Telnet Configuration Command mode: Privileged mode Function: Exiting Telnet and returning to the system. Command format: exit Note: This command can only be used in the CLI in the Telnet mode. If the user logs on in the hyper terminal mode through the serial port, this command is invalid. 3.4 Configure Mode Entering mode: Input the configure terminal command in the privileged mode. Exiting mode: exit, entering the privileged mode. Default prompt character: wlan (config) # Note: All the configuration commands can be executed in this mode (or its sub-modes).](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-32.png)
![Chapter 5 Command Line Configuration 3-73.4.1 Bridge Configuration 1. bridge aging-time Command mode: Configure mode Function: Configuring the aging time of the Bridge Forward Table (FDB) MAC address. Command format: bridge aging-time <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 10~1000000 The aging time of the FDB MAC address (unit: second), 300 by default. 2. bridge forward-table-size Command mode: Configure mode Function: Configuring the quantity of the FDB MAC addresses. Command format: bridge forward-table-size <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 220~1024 Quantity of the FDB MAC addresses, 1024 by default. 3.4.2 Clearing the Information Command mode: Configure mode Function: Clearing the alarm, log or debugging information. Command format: clear {alarm|logcmd|trace} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {alarm|logcmd| trace} Alarm, Logcmd, trace Clearing the alarm, logcmd or trace information.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-33.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-83.4.3 Configuring the Configuration Server Command mode: Configure mode Function: Configuring the parameters of configuration server: IP address, interception port number of the TCP and the interception port number of UDP. Command format: config-server {ipaddress <A.B.C.D> [tcp-port <value1> [udp-port <value2>] | udp-port <value2> [tcp-port <value1>]] | tcp-port <value1> [ipaddress <A.B.C.D> [udp-port <value2>] | udp-port <value2> [ipaddress <A.B.C.D>]] | udp-port <value2> [ipaddress <A.B.C.D> [tcp-port <value1>] | tcp-port <value1> [ipaddress <A.B.C.D>]]} Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D> IP address IP address of the configuration server <value1> 3000~65535 The interception port number of tcp, 3601 by default. <value2> 3000~65535 The interception port number of udp, 3600 by default. Note: One or multiple parameters can be configured randomly. The un-configured parameters will keep unchanged. 3.4.4 DHCP Server Configuration 1. dhcp server dns Command mode: Configure mode Function: Configuring the IP address parameters of the master and slave DNS servers of the DHCP server. Command format: dhcp server dns <A.B.C.D1> [<A.B.C.D2>] Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D1> IP address IP address of the master DNS server. <A.B.C.D2> IP address IP address of the slave DNS server (optional). 2. dhcp server gateway](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-34.png)
![Chapter 5 Command Line Configuration 3-9Command mode: Configure mode Function: Configuring the IP address parameters of the default gateway of the DHCP server. Command format: dhcp server gateway <A.B.C.D> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D> IP address IP address of the gateway. 3. dhcp server leasetime Command mode: Configure mode Function: Configuring the address lease time of the DHCP server. Command format: dhcp server leasetime <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 60~3600 The address lease time of the DHCP server, 6 by default. 4. dhcp server run Command mode: Configure mode Function: Starting, stopping or restarting the DHCP server. Command format: dhcp server run {start|stop|restart} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {start|stop|restart} Start, stop , restart start: Startup; Stop: Stopping; restart: Restarting. 5. dhcp server start-flag Command mode: Configure mode Function: Configuring the start flag of the DHCP server when the system is restarted. Command format: dhcp server start-flag {true|false}](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-35.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-10Parameter descriptions: Parameter Name Value Range Parameter Descriptions {true|false} True, false The start flag of the DHCP server. If it is “true”, the DHCP server will be started when the system is restarted. If it is “false”, the DHCP server will not be started when the system is restarted. 3.4.5 DISCOVER Configuration 1. discover device Command mode: Configure mode Function: Configuring the integrated management multicast address and port number of the equipment. Command format: discover device <A.B.C.D> [<value>] Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D> IP address with a range of 224.0.0.1 ~ 239.255.255.254. The integrated management multicast address of the equipment, 224.1.88.89 by default. <value> 0~65535 The interception port number of the integrated management multicast of the equipment, 2801 by default. 2. discover manager Command mode: Configure mode Function: Configuring the management multicast address and port number of the integrated management server. Command format: discover manager <A.B.C.D> [<value>] Parameter descriptions:](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-36.png)
![Chapter 5 Command Line Configuration 3-11Parameter Name Value Range Parameter Descriptions <A.B.C.D> IP address with a range of 224.0.0.1 ~ 239.255.255.254. The management multicast address of the integrated management server, 224.1.88.88 by default. <value> 0~65535 The management interception port number of the integrated management server, 2800 by default. 3.4.6 802.1X Parameter Configuration 1. dot1x enable Command mode: Configure mode Function: Enabling or disabling the 802.1x function. Command format: [no] dot1x enable 2. dot1x max-reauth Command mode: Configure mode Function: Configuring the maximum times of 802.1x re-authenticating. Command format: dot1x max-reauth <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 0~10 The maximum times of 802.1x re-authenticating, 5 by default. 3. dot1x max-request Command mode: Configure mode Function: Configuring the maximum times of 802.1x authentication request. Command format: dot1x max-request <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1~10 The maximum times of 802.1x authentication request, 2 by default. 4. dot1x md5-domain](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-37.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-12Command mode: Configure mode Function: Configuring the domain name in the EAP-MD5 authentication mode. Command format: dot1x md5-domain <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 32 characters The domain name in the EAP-MD5 authentication mode, USR by default. 5. dot1x nas-id Command mode: Configure mode Function: Configuring the 802.1x NAS-ID field information. Command format: dot1x nas-id <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 64 characters NAS-ID character string, W800A by default. 6. dot1x portenable Command mode: Configure mode Function: Enabling or disabling the 802.1x port control function. Command format: [no] dot1x portenable 7. dot1x quiet-period Command mode: Configure mode Function: Configuring the 802.1x quiet period. Command format: dot1x quiet-period <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1~255 The 802.1x quiet period (unit: second), 30 by default. 8. dot1x server-timeout](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-38.png)
![Chapter 5 Command Line Configuration 3-13Command mode: Configure mode Function: Configuring the time-out time of the 802.1x authentication server. Command format: dot1x server-timeout <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1~255 The authentication server time-out time (unit: second), 60 by default. 9. dot1x sim-domain Command mode: Configure mode Function: Configuring the domain name in the EAP-SIM authentication mode. Command format: dot1x sim-domain <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 32 characters The domain name in the EAP-SIM authentication mode, SIM by default. 10. dot1x supp-timeout Command mode: Configure mode Function: Configuring the time-out time of the 802.1x client. Command format: dot1x supp-timeout <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1~255 The time-out time of the 802.1x client (unit: second), 30 by default. 11. dot1x tx-period Command mode: Configure mode Function: Configuring the 802.1x sending period. Command format: dot1x tx-period <value> Parameter descriptions:](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-39.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-14Parameter Name Value Range Parameter Descriptions <value> 1~255 The 802.1x sending period (unit: second), 3 by default. 12. dot1x wpa-domain Command mode: Configure mode Function: Configuring the domain name in the WPA authentication mode. Command format: dot1x wpa-domain <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 32 characters WPA domain name, WPA by default. 3.4.7 Password Configuration in the Privileged Mode Command mode: Configure mode Function: Configuring the password for enabling the privileged mode. Command format: enable-password <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 30 characters The password for enabling the privileged mode, zte by default. 3.4.8 Erasing the Filtration Rules Command mode: Configure mode Function: Erasing the ACL rule according to the global regular numbers. Command format: erase mac-access-rule <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 0~1023 Numbers of the filtration rules. 3.4.9 Exiting the Configure Mode Command mode: Configure mode](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-40.png)
![Chapter 5 Command Line Configuration 3-15Function: Exiting the configure mode and entering the privileged mode. Command format: exit 3.4.10 IAPP Load Balance Configuration 1. iapp balance Command mode: Configure mode Function: Configuring the load balance mode and nominal capacity of the load balance group. Command format: iapp balance <vlaue1> {flow <value2>|user <value3> } Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value1> 1~65535 Load balance group ID <vlaue2> 1~65535 The lower limit of the flow implementing the load balance according to the data flow. <vlaue3> 1~30 The lower limit of the users implementing the load balance according to the user quantity. 2. iapp enable-flag Command mode: Configure mode Function: Configuring the enabling status of the load balance and the limitation of the maximum user quantity. Command format: iapp enable-flag {disable|balance|max-user} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {disable|balance| max-user} Disable, Balance, max-user disable: Disabling both of them. balance: Enabling the load balance. max-user: Enabling the limitation of maximum user quantity. & Note: Configurations iapp balance and iapp max-user can not be enabled at the same time.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-41.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-163. iapp max-user Command mode: Configure mode Function: Configuring the maximum user quantity (the quantity of the users can be accessed). Command format: iapp max-user <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1~150 The maximum quantity of the wireless users can be accessed by the system, 30 by default. 3.4.11 Entering the Interface Configuration Mode 1. interface ethernet Command mode: Configure mode Function: Entering the Ethernet interface configuration mode. The command is followed by the unit ID of the Ethernet interface. The equipment can hold multiple Ethernet interfaces. Command format: interface ethernet {0} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {0} 0 The unit ID of the Ethernet interface. The W800A only has one Ethernet interface, so this value is 0 fixedly. 2. interface wlan Command mode: Configure mode Function: Entering the Wireless interface configuration mode. The command is followed by the unit ID of the wireless interface. The equipment can hold multiple wireless interfaces. Command format: interface wlan {0|1} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {0|1} 0 or 1 The unit ID of the wireless interface. The W800A](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-42.png)
![Chapter 5 Command Line Configuration 3-17has two wireless interfaces, so this value is 0 or 1. 3.4.12 IP Network Parameter Configuration 1. ip address Command mode: Configure mode Function: Adding the IP address of the W800A management interface. Command format: [no] ip address <A.B.C.D1> <A.B.C.D2> [second] Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D1> IP address IP address of the host. <A.B.C.D2> Subnet mask Subnet mask of the host. second second The main address is without “second” and the standby address is with “second”. The main address quantity can only be one and the standby address quantity can be up to nine. 2. ip route Command mode: Configure mode Function: Configuring the default route address of the system. Command format: [no] ip route <A.B.C.D1> <A.B.C.D2> <A.B.C.D3> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D1> IP address IP address of the host. <A.B.C.D2> Subnet mask Subnet mask of the host. <A.B.C.D3> IP address IP address of the router of the next hop. 3. ip pool Command mode: Configure mode Function: Configuring the IP address pool of the system. Command format: [no] ip pool <index> <A.B.C.D1> <A.B.C.D2> <A.B.C.D3> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <index> 0~9 IP address pool group ID](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-43.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-18<A.B.C.D1> IP address Initial IP address of the host address pool. <A.B.C.D2> IP address End IP address of the host address pool. <A.B.C.D3> Subnet mask Subnet mask of the address pool address. 3.4.13 Kicking Users 1. kick all Command mode: Configure mode Function: Kicking all the users. Command format: kick all 2. kick station Command mode: Configure mode Function: Kicking the user with the specified MAC address. Command format: kick station <xx-xx-xx-xx-xx-xx> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <xx-xx-xx-xx-xx-xx> MAC address User MAC address 3.4.14 Two-Layer Separation Configuration 1. l2-separate enable Command mode: Configure mode Function: Enabling or disabling the two-layer separation function. Command format: [no] l2-separate enable 2. l2-separate gateway Command mode: Configure mode Function: Configuring the gateway MAC address . Command format: l2-separate gateway mac <xx-xx-xx-xx-xx-xx> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <xx-xx-xx-xx-xx-xx> MAC address Gateway MAC address](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-44.png)
![Chapter 5 Command Line Configuration 3-193. l2-separate mode Command mode: Configure mode Function: Configuring the two-layer separation working mode. Command format: l2-separate mode {simple_mode| gateway_mode } Parameter descriptions: Parameter Name Value Range Parameter Descriptions {simple_mode| gateway_mode } simple_mode, gateway_mode Selecting the simple mode or gateway mode for the two-layer separation. 3.4.15 Log Printing Message Configuration 1. logmsg all-enable Command mode: Configure mode Function: Enabling or disabling the log printing messages of all the modules. Command format: [no] logmsg all-enable 2. logmsg level Command mode: Configure mode Function: Configuring the levels of the log printing messages to be output. Command format: logmsg level {Lowest|Lower|Higher|Highest} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {Lowest|Lower| Higher|Highest} Lowest (Flood), Lower (Info), Higher (Error), Highest (Fatal) Level of the log printing messages to be output. Only the printing messages higher than this level can be output. 3. logmsg mod-enable Command mode: Configure mode Function: Determining the module containing the log printing messages. Command format: [no] logmsg mod-enable <module> Parameter descriptions:](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-45.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-20Parameter Name Value Range Parameter Descriptions <module> Specified module names: BSP, DATABASE, 80211, BRIDGE, IAPP, DHCP, IPPOOL, DOT1X, RADIUS, ACL, SVCMANAGE, TELNET, WEB, CONSOLE, SNMP, ALARM, R01, TFTP, DISCOVER, QOS The module containing the log printing messages. 4. logmsg telnet-log Command mode: Configure mode Function: Configuring the current Telnet window as the output window of the log printing messages Command format: [no] logmsg telnet-log 3.4.16 MAC Filtration Configuration Command mode: Configure mode Function: Adding or deleting a number accessing list. Command format: [no] mac-access-list <value> {deny|permit} {<xx-xx-xx-xx-xx-xx>|any} Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1~99 MAC filtration group ID {deny|permit} deny, permit deny: If the condition is satisfied, the MAC communication will be denied. permit: If the condition is satisfied, the MAC communication will be permitted.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-46.png)
![Chapter 5 Command Line Configuration 3-21Parameter Name Value Range Parameter Descriptions {<xx-xx-xx-xx-xx-xx> |any} MAC address or any The MAC address sending the MAC packet. Two methods can be used for specifying the source address: One is to use the format of 48-bit 6 hexadecimal hyphens, for example: 00-d0-d0-f1-c4-ef. The other is to use the keyword any as the abbreviation of the source 00-00-00-00-00-00. This keyword is not recommended. 3.4.17 MAC Address Authentication Configuration Command mode: Configure mode Function: Configuring the MAC address authentication function. Command format: [no] mac-authen {deny|permit} {<xx-xx-xx-xx-xx-xx>|any} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {deny|permit} Deny, permit deny: If the condition is satisfied, the MAC communication will be denied. permit: If the condition is satisfied, the MAC communication will be permitted. {<xx-xx-xx-xx-xx-xx> |any} MAC address or any The MAC address sending the MAC packet. Two methods can be used for specifying the source address: One is to use the format of 48-bit 6 hexadecimal hyphens, for example: 00-d0-d0-f1-c4-ef; The other is to use the keyword any as the abbreviation of the source 00-00-00-00-00-00, and this keyword is not recommended. 3.4.18 Manager Configuration Command mode: Configure mode Function: Adding or deleting the manager account. Command format: [no] manage-user <string1> <string2>](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-47.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-22Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string1> 1 ~ 32 characters User name <string2> 1 ~ 32 characters User password. 3.4.19 QoS Configuration 1. qos enable Command mode: Configure mode Function: Enabling or disabling QoS function. Command format: [no] qos enable 2. qos policy Command mode: Configure mode Function: Configuring QoS policy. Command format: qos policy {ESSID|802.1p} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {ESSID|802.1p} ESSID, 802.1p Indicating the priority policy which is the base of QoS, ESSID by default. 3.4.20 RADIUS Server Configuration 1. radius-server account Command mode: Configure mode Function: Adding or deleting the accounting server of an ISP. Command format: [no] radius-server account <string1> {master|slave} <A.B.C.D> <value> <string2> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string1> 1 ~ 32 characters ISP name, and only the created ISP can be input. {master|slave } Master, slave Master or slave flag of the accounting server. <A.B.C.D> IP address IP address of the accounting server <value> 0~65535 Port number of the accounting server](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-48.png)
![Chapter 5 Command Line Configuration 3-23Parameter Name Value Range Parameter Descriptions <string2> 1 ~ 255 characters Character string of the accounting shared secret key 2. radius-server authen Command mode: Configure mode Function: Adding or deleting the authentication server of an ISP. Command format: [no] radius-server authen <string1> {master|slave} <A.B.C.D> <value> <string2> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string1> 1 ~ 32 characters ISP name, and only the created ISP can be input. {master|slave } Master, slave Master/slave authentication server. The master authentication server can only be one. <A.B.C.D> IP address IP address of the authentication server <value> 0~65535 Port number of the authentication server <string2> 1 ~ 255 characters Character string of the authentication shared secret key 3. radius-server dns Command mode: Configure mode Function: Adding or deleting the DNS server of an ISP. Command format: [no] radius-server dns <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 32 characters ISP name, and only the created ISP can be input. 4. radius-server isp-name Command mode: Configure mode Function: Adding or deleting an ISP. Command format: [no] radius-server isp-name <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 32 characters ISP name.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-49.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-245. radius-server retry-times Command mode: Configure mode Function: Configuring the retrying times of the RADIUS authentication of an ISP. Command format: radius-server retry-times <string> <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 32 characters ISP name, and only the created ISP can be input. <value> 1~10 The retrying times of the RADIUS authentication, 3 by default. 6. radius-server timeout Command mode: Configure mode Function: Configuring the time-out time of the RADIUS authentication of an ISP. Command format: radius-server timeout <string> <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 32 characters ISP name, and only the created ISP can be input. <value> 1~65535 The time-out time of the RADIUS authentication (unit: second), 2 by default. 3.4.21 SNMP Module Configuration 1. snmp access-host Command mode: Configure mode Function: Adding or deleting the IP address of the host which can be accessed. Command format: [no] snmp access-host <A.B.C.D> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D> IP address The host IP address represented by dotted decimal (A.B.C.D) (at most 10).](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-50.png)
![Chapter 5 Command Line Configuration 3-252. snmp access-mode Command mode: Configure mode Function: Configuring the local agent can be accessed by all the hosts or the host in access-host. Command format: snmp access-mode {all|list} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {all|list} All, list all: All the users can access it. list: The users in access-host can access it. 3. snmp authtrap Command mode: Configure mode Function: Enabling or disabling the community string authentication. Command format: [no] snmp authtrap enable 4. snmp community Command mode: Configure mode Function: Configuring the SNMP access community string and its accessing authority. Command format: snmp community <string> {read-only| read-write} no snmp community <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 32 characters SNMP access community string name (at most 10). <string> is a character string with at most 32 characters. {read-only| read-write} read-only, read-write read-only: Read-only authority. read-write: Read-write authority. 5. snmp contact Command mode: Configure mode Function: Configuring the name and contact method of the equipment manager. Command format: snmp contact <End-Mark> <string>](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-51.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-26Parameter descriptions: Parameter Name Value Range Parameter Descriptions <End-Mark> Any character. Serving as the end mark of inputting character string. <string> 1 ~ 255 characters A management variable content in the MIB II system group, containing the name and contact method of the equipment manager. 6. snmp enable Command mode: Configure mode Function: Enabling or disabling the SNMP management function. Command format: [no] snmp enable 7. snmp location Command mode: Configure mode Function: Configuring the geographic location information of the managed equipment. Command format: snmp location <End-Mark> <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <End-Mark> Any character. Serving as the end mark of inputting character string. <string> 1 ~ 255 characters sysLocation, a management variable in the MIB system group, describing the geographic location of the managed equipment. 8. snmp nodecode Command mode: Configure mode Function: Configuring the NE code information of the managed equipment. Command format: snmp nodecode <value> Parameter descriptions:](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-52.png)
![Chapter 5 Command Line Configuration 3-27Parameter Name Value Range Parameter Descriptions <value> 0~241920000 A management variable in the MIB system group, describing the NE code of the managed equipment. 9. snmp nodecreatdate Command mode: Configure mode Function: Configuring the creation time information of the NE of the managed equipment. Command format: snmp nodecreatdate <hh:mm:ss> <month> <day> <year> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <hh:mm:ss> 0~241920000 hh (hour):mm (minute): ss (second) <month> 1~12 Month <day> 1~31 Date <year> 2002~2130 Year, 4 bits are needed. hh:mm:ss month day year is a management variable in the MIB system group, describing the creation time of the NE of the managed equipment. 10. snmp nodeid Command mode: Configure mode Function: Configuring the NE ID information of the managed equipment. Command format: snmp nodeid <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 0 ~ 31 characters A management variable in the MIB system group, describing the NE ID of the managed equipment. 11. snmp sysname Command mode: Configure mode Function: Configuring the name of the managed equipment. Command format: snmp sysname <End-Mark> <string> Parameter descriptions:](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-53.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-28Parameter Name Value Range Parameter Descriptions <End-Mark> Any character. Serving as the end mark of inputting character string. <string> 1 ~ 255 characters RFC1213, a management variable in the MIB system group, and it is the name of the managed equipment. 12. snmp trap enable Command mode: Configure mode Function: Enabling or disabling SNMP Agent to send trap. Command format: [no] snmp trap enable 13. snmp traphost Command mode: Configure mode Function: Adding a trap target host address and trap version number information. Command format: [no] snmp traphost <A.B.C.D> [version <value>] Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D> IP address trap target host address. <value> 1~2 trap version number. 3.4.22 SSH Parameter Configuration 1. ssh server enable Command mode: Configure mode Function: Enabling or disabling SSH function. Command format: [no] ssh server enable 2. ssh server only Command mode: Configure mode Function: Enabling or disabling SSH function, and disabling Telnet function. Command format: [no] ssh server only 3. ssh server generate-key rsa](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-54.png)
![Chapter 5 Command Line Configuration 3-29Command mode: Configure mode Function: Generating SSH server secret key. Command format: ssh server generate-key rsa 4. ssh server auth isp-name Command mode: Configure mode Function: Configuring SSH with the ISP name of the authentication server authenticated by radius. Command format: ssh server auth isp-name <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 64 characters SSH adopts the ISP name of the authentication server authenticated by radius. 5. ssh server auth mode Command mode: Configure mode Function: Configuring the SSH authentication mode. Command format: ssh server auth mode {radius|local} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {radius|local} Radius, local SSH authentication mode. 6. ssh server auth type Command mode: Configure mode Function: Configuring the SSH authentication type. Command format: ssh server auth type {chap|pap} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {chap|pap} Chap, pap SSH authentication type. 3.4.23 Spanning Tree Parameter Configuration 1. stp bridge forward-delay](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-55.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-30Command mode: Configure mode Function: Configuring the forwarding delay time of the spanning tree protocol bridge. Command format: stp bridge forward-delay <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 4~30 The forwarding delay time of the spanning tree protocol bridge (unit: second), 15 by default. 2. stp bridge hello-time Command mode: Configure mode Function: Configuring the hello time of the spanning tree protocol bridge. Command format: stp bridge hello-time <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1~10 The hello time of the spanning tree protocol bridge (unit: second), 2 by default. 3. stp bridge max-age Command mode: Configure mode Function: Configuring the maximum age of the spanning tree protocol bridge. Command format: stp bridge max-age <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 6~40 The maximum age of the spanning tree protocol bridge (unit: second), 20 by default. 4. stp bridge priority Command mode: Configure mode Function: Configuring the priority of the spanning tree protocol bridge. Command format: stp bridge priority <value> Parameter descriptions:](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-56.png)
![Chapter 5 Command Line Configuration 3-31Parameter Name Value Range Parameter Descriptions <value> 0~65535 The priority of the spanning tree protocol bridge, 32768 by default. 5. stp enable Command mode: Configure mode Function: Enabling or disabling the spanning tree protocol function. Command format: [no] stp enable 6. stp interface path-cost Command mode: Configure mode Function: Configuring the path cost of the spanning tree protocol interface. Command format: stp interface path-cost {eth0|wlan0|wlan1} <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions {eth0|wlan0|wlan1} eth0, wlan0, wlan1 Configured interface. <value> 1~65535 The path cost of the spanning tree protocol interface . 7. stp interface priority Command mode: Configure mode Function: Configuring the priority of the spanning tree protocol interface. Command format: stp interface priority {eth0|wlan0|wlan1} <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions {eth0|wlan0|wlan1} eth0, wlan0, wlan1 Configured interface. <value> 0~255 The priority of the spanning tree protocol interface, 128 by default. 8. stp interface state Command mode: Configure mode Function: Configuring the state of the spanning tree protocol interface. Command format: stp interface state {eth0|wlan0|wlan1} {enable|disable}](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-57.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-32Parameter descriptions: Parameter Name Value Range Parameter Descriptions {eth0|wlan0|wlan1} eth0, wlan0, wlan1 Configured interface. {enable|disable} Enable, disable The state of the spanning tree protocol interface, enable by default. 3.4.24 TELNET Configuration 1. telnet enable Command mode: Configure mode Function: Enabling or disabling Telnet function. Command format: [no] telnet enable 2. telnet idletime Command mode: Configure mode Function: Configuring the automatic exiting time when the Telnet window is idle. Command format: telnet idletime <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 300~3600 The automatic exiting time when the Telnet window is idle (unit: second), 300 by default. 3.4.25 Uploading/Downloading TFTP Files 1. tftp dir Command mode: Configure mode Function: Observing the spare space of the flash disk (unit: byte) Command format: tftp dir 2. tftp get: downloading files Command mode: Configure mode Function: With TFTP transmission protocol, downloading files from the TFTP server and save them to the flash disk](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-58.png)
![Chapter 5 Command Line Configuration 3-33Command format: tftp get <A.B.C.D> {runbin | zxipcmd.dat | database.dat} Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D> IP address The TFTP server IP address represented by dotted decimal. {runbin| zxipcmd.dat| database.dat} Runbin, zxipcmd.dat, database.dat The full file name (including the extension name) of the version file set to be transmitted on the TFTP server. 3. tftp pic Command mode: Configure mode Function: Downloading the picture file on the WEB configuration page from the TFTP server and save them to the flash disk. Command format: tftp pic <A.B.C.D> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <A.B.C.D> IP address The TFTP server IP address represented by dotted decimal. 4. tftp put: uploading files Command mode: Configure mode Function: With TFTP transmission protocol, uploading files from the flash disk to the TFTP server. Command format: tftp put <A.B.C.D> {runbin | zxipcmd.dat | database.dat} Parameter descriptions: Parameter Name Value Range Parameter Descriptions A.B.C.D IP address The TFTP server IP address represented by dotted decimal. {runbin| zxipcmd.dat| database.dat} Runbin, zxipcmd.dat, database.dat The full file name (including the extension name) of the file to be transmitted on the flash disk. 3.4.26 VLAN Configuration 1. vlan enable](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-59.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-34Command mode: Configure mode Function: Enabling or disabling VLAN function. Command format: [no] vlan enable 2. vlan manager-vlanid Command mode: Configure mode Function: Configuring the VLAN of the management interface. Command format: vlan manager-vlanid <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 0~4094 0: The management interface is without VLAN. 1 ~ 4094: The VLAN domain flag of the management interface. The default value is 0. 3.4.27 Web Configuration Command mode: Configure mode Function: Enabling or disabling web function. Command format: [no] web enable 3.4.28 Nation Zone Configuration Command mode: Configure mode Function: Configuring the nation and zone whether the equipment is located, for setting the corresponding channel and frequency band. Command format: zone {NA|CA|CN|TW|FR|GE|HK|KR|MX|GB|US}](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-60.png)
![Chapter 5 Command Line Configuration 3-35Parameter descriptions: Parameter Name Value Range Parameter Descriptions {NA|CA|CN|TW| FR|GE|HK|KR| MX|GB|US } NA CA CN TW FR GE HK KR MX GB US NA: Not been configured; CA: Canada; CN: China; TW: Taiwan; FR: France; GE: Germany; HK: Hongkong; KR: Korea; MX: Mexico; GB: Britain; US: USA; The default value is CN. 3.4.29 Showing Parameter Configuration 1. show alarm 1) show alarm all Command mode: Configure mode Function: Showing all the alarm information. Command format: show alarm all 2) show alarm bycode Command mode: Configure mode Function: Showing the alarm information according to the alarm codes. Command format: show alarm bycode <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1001~3999 Alarm codes. 3) show alarm bylevel Command mode: Configure mode Function: Showing the alarm information according to the alarm levels. Command format: show alarm bylevel <value>](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-61.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-36Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1~3 Alarm levels. 2. show bridge Command mode: Configure mode Function: Showing the bridge configuration parameter information. Command format: show bridge 3. show config-server Command mode: Configure mode Function: Showing the parameter information of the configuration server. Command format: show config-server 4. show dhcp server Command mode: Configure mode Function: Showing the parameter information of the DHCP server. Command format: show dhcp server 5. show discover Command mode: Configure mode Function: Showing the parameter information of the equipment discovering configuration. Command format: show discover 6. show dot1x-cfg Command mode: Configure mode Function: Showing 802.1x parameter information. Command format: show dot1x-cfg 7. show iapp Command mode: Configure mode Function: Showing the parameter information of the load balance configuration.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-62.png)
![Chapter 5 Command Line Configuration 3-37Command format: show iapp 8. show interface Command mode: Configure mode Function: Showing the parameter information of the interface configuration. Command format: show interface {ethernet|wlan} {0|1} 9. show ip 1) show ip address Command mode: Configure mode Function: Showing IP address information. Command format: show ip address 2) show ip pool = show ip pool config Command mode: Configure mode Function: Showing all the IP address pool information. Command format: show ip pool config = show ip pool used Command mode: Configure mode Function: Showing the used IP address information in the specified IP address pool. Command format: show ip pool used <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 0~9 Serial number of the IP address pool 3) show ip route Command mode: Configure mode Function: Showing the parameter information of the IP route configuration. Command format: show ip route](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-63.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-3810. show l2-separate Command mode: Configure mode Function: Showing the parameter information of the 2-layer separation configuration. Command format: show l2-separate 11. show logmsg Command mode: Configure mode Function: Showing all the configuration information and configuration historical commands of log printing. Command format: show logmsg {config|logcmd} 12. show mac-access-list Command mode: Configure mode Function: Showing the parameter information of mac-access-list filtration configuration. Command format: show mac-access-list <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1~99 MAC filtration group number. 13. show mac-authen Command mode: Configure mode Function: Showing the parameter information of mac-authen configuration. Command format: show mac-authen 14. show manage-mode Command mode: Configure mode Function: Showing the configuration information of the Telnet, snmp and web. Command format: show manage-mode 15. show manage-user](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-64.png)
![Chapter 5 Command Line Configuration 3-39Command mode: Configure mode Function: Showing the parameter information of manage-user configuration. Command format: show manage-user 16. show multi-essid Command mode: Configure mode Function: Showing the parameter information of multi-essid configuration. Command format: show multi-essid <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 0 or 1 Number of the wireless interface. 17. show qos Command mode: Configure mode Function: Showing the parameter information of qos configuration. Command format: show qos 18. show radius Command mode: Configure mode Function: Showing the parameter information of radius configuration. Command format: show radius 19. show snmp 1) show snmp access-host Command mode: Configure mode Function: Showing the parameter information of snmp access-host configuration. Command format: show snmp access-host 2) show snmp community Command mode: Configure mode Function: Showing the parameter information of snmp community](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-65.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-40configuration. Command format: show snmp community 3) show snmp nodeinfo Command mode: Configure mode Function: Showing the parameter information of snmp nodeinfo configuration. Command format: show snmp nodeinfo 4) show snmp sysinfo Command mode: Configure mode Function: Showing the parameter information of snmp sysInfo configuration. Command format: show snmp sysinfo 5) show snmp traphost Command mode: Configure mode Function: Showing the parameter information of snmp traphost configuration. Command format: show snmp traphost 20. show station-info Command mode: Configure mode Function: Showing the information of the client connected to W800A. Command format: show station-info 21. show ssh Command mode: Configure mode Function: Showing the parameter information of SSH configuration. Command format: show ssh 22. show stp 1) show stp bridge Command mode: Configure mode Function: Showing the parameter information of stp bridge configuration.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-66.png)
![Chapter 5 Command Line Configuration 3-41Command format: show stp bridge 2) show stp interface Command mode: Configure mode Function: Showing the parameter information of stp interface configuration. Command format: show stp interface 23. show telnet-idletime Command mode: Configure mode Function: Showing the parameter information of the automatic exiting time when the Telnet window is idle. Command format: show telnet-idletime 24. show trace Command mode: Configure mode Function: Showing the printing information of the client. Command format: show trace 25. show version Command mode: Configure mode Function: Showing the software version number information. Command format: show version 26. show vlan Command mode: Configure mode Function: Showing the vlan configuration information. Command format: show vlan 3.5 Ethernet Interface Configuration Mode Entering mode: Input the interface Ethernet 0 command in the configure mode. Exiting mode: exit, entering the configure mode. Default prompt character: wlan (config-eth) #](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-67.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-42Note: All the information of the corresponding interface can be configured in this mode. 3.5.1 Exiting the Ethernet Interface Configuration Mode Command mode: Ethernet interface configure mode Function: Exiting the Ethernet interface configuration mode and entering the configure mode. Command format: exit 3.5.2 Ethernet Interface MAC Filtration Configuration Command mode: Ethernet interface configure mode Function: Configuring the Ethernet interface MAC filtration. Command format: [no] macl-bind <value> {in} Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1~99 The article number of the MAC filtration bound to the interface. {in} in The in direction bound to the interface. 3.6 Wireless Interface Configuration Mode Entering mode: Input the interface wlan {0|1} command in the configure mode. Exiting mode: exit, entering the configure mode. Default prompt character: wlan (config-wlan) # Note: All the information of the corresponding interface can be configured in this mode. 3.6.1 802.11-Related Parameter Configuration of the Wireless Interface 1. 80211 authmode Command mode: Wireless interface configure mode Function: Configuring the wireless authentication mode of the AP. Command format: 80211 authmode {OpenSystem | ShareKey}](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-68.png)
![Chapter 5 Command Line Configuration 3-43Parameter descriptions: Parameter Name Value Range Parameter Descriptions {OpenSystem| ShareKey} OpenSystem, ShareKey The wireless authentication mode is configured as open system or shared secret key mode. 2. 80211 essid Command mode: Wireless interface configure mode Function: Configuring the wireless network ESSID. Command format: 80211 essid <string> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 31 characters Wireless network ESSID. By default, interface 0 is wireless0 and interface 1 is wireless1. 3. 80211 frg-threshold Command mode: Wireless interface configure mode Function: Configuring the fragment threshold. Command format: 80211 frg-threshold <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 256 ~ 2346 (even number) The fragment threshold, 2346 by default. 4. 80211 rts-threshold Command mode: Wireless interface configure mode Function: Configuring the RTS threshold. Command format: 80211 rts-threshold <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 0~2347 RTS threshold, 2347 by default. . 5. 80211 wirelessmode Command mode: Wireless interface configure mode](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-69.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-44Function: Configuring the wireless standard working mode of the wireless interface. Command format: 80211 wirelessmode {11a|11b|11g|help} [channel <num>] [rate <value>] Parameter descriptions: Parameter Name Value Range Parameter Descriptions {11a|11 b|11g|help} 11a, 11b, 11g, help 11a: Configuring 800A as the 802.11a working mode. 11b: Configuring 800A as the 802.11b working mode. 11g: Configuring 800A as the 802.11g working mode. help: Listing the configurable channels in the current working mode, according to the configured country code. <num> Configure the 800A working channel. Select the proper channel according to the country code. See Table 3.6-1 for the corresponding relationship of the nation code and selectable channel. <value> 11a: auto, 6Mbps, 9Mbps, 12Mbps, 18Mbps, 24Mbps, 36Mbps, 48Mbps, 54Mbps; 11b: auto, 1Mbps, 2Mbps, 5.5Mbps, 11Mbps; 11g: auto, 6Mbps, 9Mbps, 12Mbps, 18Mbps, 24Mbps, 36Mbps, 48Mbps, 54Mbps Configuring the 800A working rate.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-70.png)
![Chapter 5 Command Line Configuration 3-45Table 3.6-1 W800A Working Channels Abbreviations of Nations and Zones Full Names of Nations and Zones 11a Available Channel Numbers 11b Available Channel Numbers 11g Available Channel Numbers CN CHINA 0 (Auto), 149, 153, 157, 161, 165 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 CA CANADA 0 (Auto), 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 TW TAIWAN 0 (Auto), 56, 60, 64, 149, 153, 157, 161 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 FR FRANCE 0 (Auto), 36, 40, 44, 48, 52, 56, 60, 64 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 GE GERMANY 0 (Auto), 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 HK HONG KONG 0 (Auto), 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 KR KOREA REPULIC 0 (Auto), 149, 153, 157, 161 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 MX MEXICO 0 (Auto), 52, 56, 60, 64, 36, 40, 44, 48, 149, 153, 157, 161, 165 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 GB the UNITED KINGDOM 0 (Auto), 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 US the UNITED STATES 0 (Auto), 52, 56, 60, 64, 36, 40, 44, 48, 149, 153, 157, 161, 165 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 0 (Auto), 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 3.6.2 ESSID Hiding Configuration Command mode: Wireless interface configure mode Function: Enabling or disabling the ESSID. Command format: [no] essid-hide enable](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-71.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-463.6.3 Exiting the Wireless Interface Configuration Mode Command mode: Wireless interface configure mode Function: Exiting the wireless interface configuration mode and entering the configure mode. Command format: exit 3.6.4 Enabling the Link Integrity Detection Function Command mode: Wireless interface configure mode Function: Enabling or disabling the AP link integrity detection function. Command format: [no] link-integrity enable Note: AP link integrity detection function is: when AP Ethernet links are disconnected, AP will release all the created wireless users and close the wireless interface, denying the connection requests from other wireless terminals; when AP Ethernet links are restored normally, AP will open the wireless interface and receive the wireless user connections. If the AP placement position is difficult to be reached, please be cautious to use this function. 3.6.5 Wireless Interface MAC Filtration Configuration Command mode: Wireless interface configure mode Function: Configuring the wireless interface MAC filtration. Command format: [no] macl-bind <value> {in} Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 1~99 The article number of the MAC filtration bound by the interface. {in} in The in direction bound to the interface. 3.6.6 Multi-ESSID Configuration Command mode: Wireless interface configure mode Function: Configuring the VLAN ID, maximum user quantity and priority corresponding to the ESSID. Command format: multi-essid <string> [vlan-id <value1>] [max-user <value2>]](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-72.png)
![Chapter 5 Command Line Configuration 3-47[priority <value3>] Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 1 ~ 32 characters ESSID name. <value1> 1~4094 The VLAN ID corresponding to the ESSID. <value2> 1~30 The maximum user quantity corresponding to the ESSID. <value3> 0~7 The priority corresponding to the ESSID. 3.6.7 Security Parameter Configuration 1. security mode Command mode: Wireless interface configure mode Function: Configuring the security mode. Command format: security mode {none|wep64|wep128|wep152|wpa-eap-tls| wpa-psk} {Alphanumeric|Hexadecimal} {TKIP|AES} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {none|wep64| wep128|wep152| wpa-eap-tls| wpa-psk} none, wep64, wep128, wep152, wpa-eap-tls, wpa-psk none: No encryption wep64: Encryption of WEP 64-bit secret key mode. wep128: Encryption of WEP 128-bit secret key mode. wep152: Encryption of WEP 152-bit secret key mode. wpa-eap-tls: Encryption of wpa mode. wpa-psk: Encryption of wpa-psk mode. {Alphanumeric| Hexadecimal} Alphanumeric, Hexadecimal Alphanumeric: WEP secret key is in the character string format. Hexadecimal: WEP secret key is in the hexadecimal format. {TKIP|AES } TKIP, AES Configuring the WPA encryption mode. 2. security wep set-key Command mode: Wireless interface configure mode Function: Configuring the WEP encryption secret key. Command format: security wep set-key {key1|key2|key3|key4}](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-73.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-48<character/hex> Parameter descriptions: Parameter Name Value Range Parameter Descriptions {key1|key2| key3|key4} key1, key2, key3, key4 The article number of the secret key to be configured. <character/hex> wep64: 5 characters/10 hexadecimal numerals; wep128: 13 characters/26 hexadecimal numerals; wep152: 16 characters/32 hexadecimal numerals. If 64-bit encryption is configured, <string> can be 5 case-sensitive characters (Alphanumeric format) or 10 hexadecimal numerals (Hexadecimal format). If 128-bit encryption is configured, <string> can be 13 case-sensitive characters (Alphanumeric format) or 26 hexadecimal numerals (Hexadecimal format). If 152-bit encryption is configured, <string> can be 16 case-sensitive characters (Alphanumeric format) or 52 hexadecimal numerals (Hexadecimal format). 3. security wep use-key Command mode: Wireless interface configure mode Function: Configuring the WEP encryption secret key to be used. Command format: security wep use-key {key1|key2|key3|key4} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {key1|key2| key3|key4} key1, key2, key3, key4 The article number of the secret key to be used. 4. security wpa pre-shared-key Command mode: Wireless interface configure mode Function: Configuring the WPA mode to be used. Command format: security wpa pre-shared-key <string>](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-74.png)
![Chapter 5 Command Line Configuration 3-49Parameter descriptions: Parameter Name Value Range Parameter Descriptions <string> 8 ~ 36 characters Configuring the shared secret key of the WPA encryption. 5. security wpa rekey-interval Command mode: Wireless interface configure mode Function: Configuring the WPA mode to be used. Command format: security wpa rekey-interval <value> Parameter descriptions: Parameter Name Value Range Parameter Descriptions <value> 30~3600 Configuring the updating interval of the dynamic secret key (unit: second). 3.6.8 Transmission Power Configuration Command mode: Wireless interface configure mode Function: Configuring the transmission power of the equipment. Command format: tx-power {full|half|quarter|eighth|min} Parameter descriptions: Parameter Name Value Range Parameter Descriptions {full|half|quarter| eighth|min} full, half, quarter, eighth, min full: Maximum transmission power; half: Half transmission power; quarter: Quarter transmission power; eight: Eighth transmission power; min: Minimum transmission power; 3.6.9 Working Mode Configuration Command mode: Wireless interface configure mode Function: Configuring the working mode of the equipment. Command format: workmode {ap|repeater}](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-75.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 3-50Parameter descriptions: Parameter Name Value Range Parameter Descriptions {ap|repeater} ap, repeater The working mode of the equipment.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-76.png)
![1 A.1 Making of Ethernet Cables A.1.1 Making of Straight Through Ethernet Cables (RJ45) In IP wireless access system, the following network cables must adopt the straight through Ethernet cables: 1. The Ethernet cable between the Ethernet switch (end A) and W112P (end B). 2. When no Ethernet switch is used, AP will directly connect with the AC downlink port, at this time, the Ethernet cable between the AC (end A) and AP (end B) must be straight through Ethernet cable. 3. In the cases where no Ethernet switch is used, as when the system adopts the Ethernet power supply, the AC downlink port will directly connect with W112P, at this time, the Ethernet cable between the AC (end A) and W112P (end B) must be straight through Ethernet cable. The connections of the straight through Ethernet cables are shown in Table A.1-1. Table A.1-1 Connections of Straight Through Ethernet Cables (RJ45) End A Signal Name Conductor Color End B Signal Name Conductor Color 1 Data receiving Rx+ White/orange 1 Data transmitting Tx+ White/orange 2 Data receiving Rx- Orange 2 Data transmitting Tx- Orange 3 Data transmitting Tx+ White/green 3 Data receiving Rx+ White/green 4 MATCH1 Blue 4 MATCH1 Blue 5 MATCH2 White/blue 5 MATCH2 White/blue 6 Data transmitting Tx- Green 6 Data receiving Rx- Green 7 MATCH3 White/brown 7 MATCH3 White/brown 8 MATCH4 Brown 8 MATCH4 Brown A.1.2 Making of Straight Through Power Supply Ethernet Cables (C-RJ45-001) The Ethernet cable between the W112P (end A) and AP (end B) not only serves as the Ethernet data signal cable, but also provides -48V DC power for two twisted pairs 4&5 and 7&8 on the load balance, to power AP remotely. The connection method of this cable is the same as that of the straight through cable without power supply, and the connection table is shown in Table A.1-2.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-77.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 2Table A.1-2 Connections of Straight Through Power Supply Ethernet Cables (C-RJ45-001) End A Signal Name Conductor Color End B Signal Name Conductor Color 1 Data receiving Rx+ White/orange 1 Data transmitting Tx+ White/orange 2 Data receiving Rx- Orange 2 Data transmitting Tx- Orange 3 Data transmitting Tx+ White/green 3 Data receiving Rx+ White/green 4 GND Blue 4 GND Blue 5 GND White/blue 5 GND White/blue 6 Data transmitting Tx- Green 6 Data receiving Rx- Green 7 -48V White/brown 7 -48V White/brown 8 -48V Brown 8 -48V Brown & Note: These cables contain -48 V DC power supply. Do prevent any short circuits; otherwise, the signal will be interrupted and the equipment may not work normally, and even the equipment protection action will be activated. GND and -48 V each occupy one twisted pair. These twisted pairs should be separate, otherwise short circuit may occur. A.1.3 Making of Crossover Ethernet Cables (RJ45J) The connections of the crossover Ethernet cables are shown in Table A.1-3. Table A.1-3 Connections of Crossover Ethernet Cables (RJ45J) End A Signal Name Conductor Color End B Signal Name Conductor Color 1 Data receiving Rx+ White/orange 3 Data transmitting Tx+ White/green 2 Data receiving Rx- Orange 6 Data transmitting Tx- Green 3 Data transmitting Tx+ White/green 1 Data receiving Rx+ White/orange 4 MATCH1 Blue 4 MATCH1 Blue 5 MATCH2 White/blue 5 MATCH2 White/blue 6 Data transmitting Tx- Green 2 Data receiving Rx- Orange 7 MATCH3 White/brown 7 MATCH3 White/brown 8 MATCH4 Brown 8 MATCH4 Brown](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-78.png)
![Appendix A Making of Ethernet Cable 3& Note: The signals and connection methods mentioned here are designed according to the signal definitions of the ZTE AC equipment interface. If the AC in the actual engineering is not from ZTE, modify the cable making methods according to the actual conditions. A.1.4 Ethernet Cable Label After the Ethernet cable is crimped, paste labels on ends A and B of the network cable, indicating name and length of this cable. 1. Label of the straight through Ethernet cable The label of the straight through Ethernet cable (RJ45) is shown in Fig. A.1-1. Fig. A.1-1 Label of the Straight Through Ethernet Cable In the diagram, “**m” indicates the actual length of the cable. 2. Label of the straight through power supply Ethernet cable The label of the straight through power supply Ethernet cable (C-RJ45-001) is shown in Fig. A.1-2. Fig. A.1-2 Label of the Straight Through Power Supply Ethernet Cable In the diagram, “**m” indicates the actual length of the cable; “PoE Cable” indicates that this is the Ethernet power cable. 3. Label of the Crossover Ethernet Cable The label of the crossover Ethernet cable (RJ45J) is shown in Fig. A.1-3.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-79.png)
![ZXR10 WAS (V2.0) IP Wireless Access System W800A Wireless Access Point Professional Installation Instruction Manual 4RJ45J **m Fig. A.1-3 Label of the Crossover Ethernet cable In the diagram, “**m” indicates the actual length of the cable; “J” after “RJ45” indicates that this is the crossover Ethernet cable.](https://usermanual.wiki/ZTE/ZXR10W800A.Professional-Installation-Manual/User-Guide-455794-Page-80.png)