Yanfeng Visteon Automotive Electronics BTM01 2.4GHz Bluetooth Module User Manual BTM01

Yanfeng Visteon Automotive Electronics Co.,Ltd 2.4GHz Bluetooth Module BTM01

BTM01 User Manual

BTM01 User ManualFeatures Fully qualified Bluetooth® v2.1 + EDRspecification Piconet and scatternet support Minimum external components UART to 4Mbaud SDIO (Bluetooth Type A)/CSPI interface Integrated CSR AuriStream® low-power codec forwide-band voice qualityGeneral DescriptionBTM01 is a single-chip radio and baseband Module for Bluetooth 2.4GHz systemsincluding EDR to 3Mbps.It is based on CSR BlueCore6-ROM QFN Automotive chip. Itprovides a fully compliant Bluetooth v2.1 + EDR specification system for data and voicecommunications.BTM01includes AuriStream, which offers significant power reduction over the CVSD-based system when used at both ends of the link.Applications AutomotiveThe device incorporates auto-calibration and BIST routines to simplify development, typeapproval and production test. All hardware and device firmware is fully compliant withthe Bluetooth v2.1 + EDR specification.Electrical parametersVCC=3.3+/-0.3VOperation temperature:-30 to 75 degree
Device Pinout1BT_RST2PCM_OUT3 PCM_SYNC4 BT_RX5BT_TX63.3V7GND8BT_RTS9 BT_CTS10 PCM_CLK11 PCM_IN12 GND
EC DECLARATION OF CONFORMITYWe Yanfeng Visteon Automotive Electronics Co.,Ltd. declared that followingdesignated product:Product Name: Bluetooth Module of R0-13Model No: BTM01Complies with the essential protection requirements of the Radio andTelecommunication Terminal Equipment Directive (EC Directive 1999/5/EC) and theElectromagnetic Compatibility Directive(2004/108/EC).This declaration applies to all specimens manufactured identical to the samplessubmitted for testing/evaluation. Assessment of compliance of the product with therequirements relating to the Radio and Telecommunication Terminal EquipmentDirective (EC Directive 1999/5/EC) and the Electromagnetic CompatibilityDirective(2004/108/EC) was performed by British Approvals Board forTelecommunications (BABT) (Notified Body No.0168), based on the following standards:Safety:EN 60950-1:2006+ A1:2010+A11:2009+A12:2011IEC 60950-1:2005+A1:2009EN 62479:2010Radio:ETSI EN 300 328 v1.7.1EMC:ETSI EN 301 489-1 v1.9.2ETSI EN 301 489-17 v2.2.1
NOTE: This equipment has been tested and found to comply with the limits for aClassB digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interferencein a residential installation.This equipment generate, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occurin a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the followingmeasures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.—Consult the dealer or an experienced radio/TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that maycause undesired operation.Caution: the user that changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority to operate the equipment.Caution: the user that changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority to operate the equipment.

Navigation menu