Yaesu Musen 20461X50 Scanning Receiver User Manual FTDX3000 Operating Manual
Yaesu Musen Co., Ltd. Scanning Receiver FTDX3000 Operating Manual
UserManual.wiki
>
Yaesu Musen
>
20461X50 User Manual
>
Users Manual 4
Contents
1.
Users Manual 1
2.
Users Manual 2
3.
Users Manual 3
4.
Users Manual 4
5.
Users Manual 5
6.
Users Manual 6
7.
Users Manual 7
8.
Users Manual 8
9.
Users Manual 9
10.
Users Manual 10
11.
Users Manual 11
12.
Users Manual 12
13.
Users Manual 13
14.
Users Manual 14
Users Manual 4
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![Page 34 FT DX 3000 OperaTing ManualopeRAtioN oN 60-MeteR (5 MHz) bANd (u.s. ANd u.K. veRsioN oNly)The recently-released 60-meter band is covered, in the FT DX 3000, by xed memory channels. These channels are set to USB, and they appear between the “last” PMS channel (“P9U”) and the rst “regular” memory channel (Channel 1):1. Press the [V/M] button once to enter the “Memory” mode; the “MCH” icon will appear in the display and a memory channel number will appear on the display.Advice: If you can not enter the “Memory” mode, check to see if the transceiver is in VFO-B mode (the green [(VFO-B)RX] Indicator/Switch is illuminated). If so, press the [(VFO-A)RX] Indicator/Switch to return operation to VFO-A. Now, press the [V/M] button to enter the “Memory” mode.2. Press the [MCH] button located on the bottom right of the [CLAR/VFO-B] knob. The LED imbedded in the button will glow orange to signify that rotation of the [CLAR/VFO-B] knob will allow selection of the memory channel.3. Memory channels (“5M-01” through “5M-10”) are pre-programmed, at the factory, with the permitted frequencies in the 5 MHz band, and the USB mode is automatically selected on these channels.4. To exit from 60-meter operation and return to the VFO mode, just press the [V/M] button.Note:The frequencies and operating mode for 5 MHz band operation are xed, and may not be changed.Basic OperaTiOn:receiving On aMaTeur BanDs[CLAR/VFO-B] Knob[VFO-B(RX)] Button[MCH] Button[V/M] Button[VFO-A(RX)] ButtonMain Tuning Dial KnobcHANNel NuMbeR5M-015M-025M-035M-045M-055M-065M-075M-085M-095M-10FReQueNcy5.332000 MHz5.348000 MHz5.358500 MHz5.373000 MHz5.405000 MHz5.332000 MHz5.348000 MHz5.358500 MHz5.373000 MHz5.405000 MHzFCC ID: K6620461X50 / IC: 511B-20461X50](https://usermanual.wiki/Yaesu-Musen/20461X50.Users-Manual-4/User-Guide-1770289-Page-1.png)
![Page 35FT DX 3000 OperaTing ManualBasic OperaTiOn:receiving On aMaTeur BanDsclAR (clARiFieR) opeRAtioNThe [RX CLAR], [TX CLAR], [CLEAR] buttons and [CLAR/VFO-B] knob are used to offset the receive frequency, the transmit frequency, or both, from their settings on the VFO-A frequency. Four small numbers on the Multi-Display Window show the current Clarier offset. The Clarier controls on the FT DX 3000 are designed to allow you to preset an offset (up to ±9.999 kHz) without actually retuning, and then to activate it via the Clarier’s [RX CLAR] and [TX CLAR] buttons. This feature is ideal for following a drifting station, or for setting small frequency offsets sometimes utilized in DX “Split” work.Here is the technique for utilizing the Clarier:1. Press the [RX CLAR] button. In the Multi-Display Window, the “RX” notation will appear, and the programmed offset will be applied to the receive fre-quency.2. Rotation of the [CLAR/VFO-B] knob will allow you to modify your initial offset on the y. Offsets of up to ±9.99 kHz may be set using the Clarier.To cancel Clarier operation, press the [RX CLAR] but-ton. The “RX” notation will disappear from the display.Advice: Turning the Clarier off simply cancels the applica-tion of the programmed offset from the receive and/or the transmit frequencies. To clear the Clarifier offset, and reset it to “zero,” press the [CLEAR] but-ton. The programmed offset is displayed in the small multi-channel window of the frequency display. You may also activate the clarier on the VFO-B fre-quency. In this case, the offset frequency is set using the Main Tuning Dial knob, instead of the [CLAR/VFO-B] knob. The Clarier operation (including the offset frequen-cy) will be memorized independently on each VFO stack of VFO-A and VFO-B.[CLAR/VFO-B] Knob[RX CLAR] Button[TX CLAR] Button[CLEAR] ButtonTXCLARAlternately, You may apply the Clarifier offset to the transmit frequency, without changing the receive frequency (typically, for “split” DX pile-ups).[CLAR/VFO-B] Knob[p/q] ButtonTheTuningOffsetIndicatorprovidesagraphicalrepresentationoftheClarieroffset.In the factory default setting On CW, the Tuning Offset Indicator is used for CW Cen-ter Tuning, instead of Clarier Offset. If you wish to change this so that the Clarier Offset is also displayed on CW, use the following procedure: [Plus (+) Offset][Zero Offset][Minus (–) Offset][SELECT] button1. Press and hold in the [MENU] button for one second to enter the Menu mode.2. Rotate the [CLAR/VFO-B] knob or p/q button to select Menu item “011 DISPLAY BAR DIS-PLAY SELECT”.3. Press the [SELECT] button then rotate the [CLAR/VFO-B] knob or p/q button to select “CLAR (Clarifier)” (replacing the default “CW TUNE (CW TUNING)” selection).4. Press the [SELECT] button, then press the [MENU] button to save the new setting and exit to normal operation.Multi-Display Window[MENU] buttonFCC ID: K6620461X50 / IC: 511B-20461X50](https://usermanual.wiki/Yaesu-Musen/20461X50.Users-Manual-4/User-Guide-1770289-Page-2.png)
![Page 36 FT DX 3000 OperaTing ManualBasic OperaTiOn:receiving On aMaTeur BanDsLOCKYou may lock the setting of the Main Tuning Dial knob (for VFO-A frequency tuning) and the [CLAR/VFO-B] knob (for VFO-B frequency tuning), to prevent accidental frequency change.Main Tuning Dial knob LockTo lock the Main Tuning Dial knob, press the [(VFO-A)RX] Indicator/Switch to illuminate the imbedded green LED, then press the [LOCK] button that is located to the right of the Main Tuning Dial knob. To unlock the Dial setting, and restore normal tuning, press the [LOCK] button once more.[CLAR/VFO-B] knob LockTo lock the [CLAR/VFO-B] knob, press the [VFO-B/CLAR] button that is located to the right of the [CLAR/VFO-B] knob. Indicator/Switch to illuminate the imbed-ded orange LED, then press the [TX CLAR (LOCK)] button that is located to the top of the [CLAR/VFO-B] knob. To unlock the [CLAR/VFO-B] knob, and restore normal tuning, press the [TX CLAR (LOCK)] button once more.Advice:The lock feature will be memorized independently on each Main Tuning Dial knob and the [CLAR/VFO-B] knob.DIMMERThe illumination level of the display may be adjusted via Menu item “005 DISP DIM VFD”.To adjust the illumination level:1. Press and hold in the [MENU] button for one second to enter the Menu mode.2. Rotate the [CLAR/VFO-B] knob or p/q button to select Menu item “010 DISPLAY DIMMER TFT”.3. Press the [SELECT] button then rotate the [CLAR/VFO-B] knob or p/q button to select the desired illumination level.4. Press the [SELECT] button, then press the [MENU] button to save the new setting and exit to normal op-eration.[TX CLAR(LOCK)] Button[VFO-B/CLAR] Button[LOCK] Button[CLAR/VFO-B] Knob[p/q] Button[SELECT] button[MENU] buttonFCC ID: K6620461X50 / IC: 511B-20461X50](https://usermanual.wiki/Yaesu-Musen/20461X50.Users-Manual-4/User-Guide-1770289-Page-3.png)
![Page 37FT DX 3000 OperaTing ManualcOnvenience FeaTuresusiNg tHe vFo-b[AB] Button[CLAR/VFO-B] Knob[AB] ButtonMain Tuning Dial Knob[clAR/vFo-b] KNob tuNiNg RAteopeRAtiNg Mode 1 step 1 diAl RotAtioN NoRMAl [FAst] NoRMAl [FAst]LSB/USB/CW/AM/ 10 Hz 2 kHzRTTY/PKT(LSB) [100 Hz] [20 kHz] FM/PKT(FM) 100 Hz [1 kHz] 20 kHz [200 kHz][ ] : [FAST] switch set to “ON”VFO-B operates similar to VFO-A, which you should be familiar with by now. However, the [CLAR/VFO-B] knob, instead of the Main Tuning Dial knob selects the frequency for VFO-B (See box below for tuning rate). The two VFOs make simple transmit/receive split fre-quency operation possible. Use various combinations of the four VFO red and green transmit and receive switches to set up split frequency operation. The [SPLIT] button also sets up split frequency operation. See page 69 for details about Split-Frequency Operation.The frequency and mode data can be transferred from VFO-A to VFO-B by pressing the [AB] button, don’t forget that this will overwrite any settings that were in VFO-B previously. Also, the contents of the two VFOs can be swapped (with no loss of data) by pressing the [AB] button.Most of the interference reduction features, which are described later, can also be used on VFO-B.Two things you cannot do with VFO-B that you can do with VFO-A, are store the contents of VFO-B directly into a memory, and set the Clarifier offset. For these functions you need to swap the VFO-B with the VFO-A by pressing the [AB] button, then store the contents into the memory or set the Clarier.Advice:It is possible to set the frequency change over one dial rotation, separately for the CW mode, using the Menu items “084 TUN DIALSTP” and “085 TUN CW FINE”.FCC ID: K6620461X50 / IC: 511B-20461X50](https://usermanual.wiki/Yaesu-Musen/20461X50.Users-Manual-4/User-Guide-1770289-Page-4.png)
![Page 39FT DX 3000 OperaTing ManualcOnvenience FeaTuresbANd stAcK opeRAtioNThe FT DX 3000 utilizes a triple band-stack VFO selection technique, that permits you to store up to three favorite fre-quencies and modes onto each band’s VFO register. For example, you may store one frequency each on 14 MHz CW, RTTY, and USB, then recall these VFOs by successive, momentary presses of the [14] MHz band button. Each Amateur band key may similarly have up to three frequency/mode settings applied. Both the VFO-A and VFO-B systems have their own, independent, band stacks.A typical setup, for the 14 MHz band, might be arranged like this:1. Program 14.025 MHz, CW Mode, then press the [14] MHz band button;2. Program 14.080 MHz, RTTY Mode, then press the [14] MHz band button;3. Program 14.195 MHz, SSB Mode, then press the [14] MHz band button.With this conguration, successive momentary presses of the [14] MHz band button will allow you to step se-quentially through these three VFOs.c.s (custoM switcH)The front panel [C.S] button may be programmed to directly access an often-used Menu Mode selection.[BAND] ButtonC.S Setup1. Press and hold in the [MENU] button for one second to engage the Menu mode; the Menu list will appear on the display.2. Rotate the [CLAR/VFO-B] knob or p/q button to select the Menu item you want to access with the front panel [C.S] button.3. Press the [C.S] button to lock in your selection.4. Press the [SELECT] button, then press the [MENU] button to save the new conguration and exit to nor-mal operation.Menu Selection Recall via [C.S] buttonPress the [C.S] button.The programmed Menu item will appear on the dis-play. You may now rotate the [CLAR/VFO-B] knob to change the setting of this menu item. Press and hold the [MENU] button for one second, when you are done, to save the new conguration and exit to normal operation.[SELECT] Button[C.S] Button [CLAR/VFO-B] Knob[MENU] ButtonFCC ID: K6620461X50 / IC: 511B-20461X50](https://usermanual.wiki/Yaesu-Musen/20461X50.Users-Manual-4/User-Guide-1770289-Page-6.png)