Xi an NovaStar Tech T3 Taurus-MediaPlayer User Manual OEM installation Manual

Xi'an NovaStar Tech Co., Ltd Taurus-MediaPlayer OEM installation Manual

UserManual.wiki >

Xi an NovaStar Tech >

T3 User Manual >

OEM installation Manual

Contents

1. Host User Manual
2. OEM installation Manual

OEM installation Manual

Taurus SeriesMultimedia PlayersQuick Start GuideVersion:V1.0.0Doc. ID:NS120100144

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.0iChange HistoryVersionRelease DateDescriptionV1.0.02017-07-20First release.

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.0iiTable of ContentsChange History................................................................................................................................. iTable of Contents............................................................................................................................ ii1Overview.........................................................................................................................................11.1 Scenario........................................................................................................................................................................11.2 Procedures................................................................................................................................................................... 12Preparation.................................................................................................................................... 22.1 Getting and Installing Software................................................................................................................................. 22.2 Getting Documents..................................................................................................................................................... 32.3 Getting Required Account Information.................................................................................................................... 33Taurus Connections.................................................................................................................... 43.1 Connecting via Ethernet Cable................................................................................................................................. 43.2 Connecting via Local Area Network (LAN)............................................................................................................. 43.3 Connecting via Wi-Fi.................................................................................................................................................. 53.3.1 Wi-Fi AP Mode......................................................................................................................................................... 53.3.2 WiFi Sta Mode..........................................................................................................................................................63.3.3 WiFi AP+Sta Mode.................................................................................................................................................. 64Receiving Card Parameter Configuration............................................................................. 84.1 Loading Configuration File or Configuring the Parameters Manually Through NovaLCT-Taurus................. 84.2 Loading the Configuration File Through ViPlex Handy.........................................................................................95Screen Configuration................................................................................................................105.1 Configuring a Screen Through ViPlex Handy...................................................................................................... 106General Operations................................................................................................................... 116.1 Taurus Login with ViPlex Handy (Android and iOS)........................................................................................... 116.2 Taurus Login with ViPlex Express (Windows)......................................................................................................117Caution......................................................................................................................................... 13

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.011Overview1.1 ScenarioThis document introduces a quick way to use Taurus series multimedia players andprovides instructions for the first-timer.1.2 Procedures

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.022Preparation2.1 Getting and Installing SoftwareItemDescriptionHow to getHow to installViPlex HandyIt is a LAN-baseddisplaymanagementsoftware, includingthe one applicableto Android and iOSoperating systems,is mainly used fordisplaymanagement aswell as solutionediting andpublishing.Scan the followingOR code to downloadand install the APP.Use the App Store onyour iPhone to getViPlex Handy for iOS.Softwareinstallation isthe same asotherapplications.ViPlex ExpressIt is a LAN-baseddisplaymanagementsoftware applicableto the Windowsoperating system,and is mainly usedfor displaymanagement aswell as solutionediting andpublishing.Visitwww.novastar.tech,download and installthe required software.NovaLCT-TaurusScreenconfigurationsoftware, which onlysupports Windowsand is mainly usedfor adjustingscreens to theoptimal displaystatus.Visitwww.novastar.tech,download and installthe required software.

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.032.2 Getting DocumentsItemDescriptionHow to getTaurus SeriesMultimedia PlayersProductDescription-V1.0.0Describing applicationscenarios, features, safetyinstructions, hardwarestructure, software structureand specifications of Taurusseries products.Visit www.novastar.tech todownload the requireddocuments.2.3 Getting Required Account InformationItemAccount NameDefault PasswordConnect Taurus WiFi APAP+ last 8 digits of the SN,For example: AP1000003312345678Log into the Taurusadmin123456

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.043Taurus Connections3.1 Connecting via Ethernet CableNetwork DiagramUsers can access the Taurus directly when it is connected via the Ethernet cable.ConfigurationStep 1 Refer to “6 General Operations” to log in to the Taurus.Step 2 Turn off DHCP and set static IP address for the Taurus.ViPlex Handy: Select Network Setting,Wired Network Setting in the Screenmanagement page.ViPlex Express: Select Screen Control,Network configuration.3.2 Connecting via Local Area Network (LAN)Network DiagramUsers can access the Taurus through LAN when it is connected via LAN.

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.05ConfigurationNo need for configuration.3.3 Connecting via Wi-FiThe Taurus series products have dual WiFi function which can provide Wi-Fi hotspotas well as serve as WiFi Station at the same time. The WiFi working frequency rangeis 2400~2483.5MHz.3.3.1 Wi-Fi AP ModeNetwork DiagramUsers can access the Taurus directly when it is connected via WiFi AP.ConfigurationNo need for configuration. Please connect the WiFi AP of the Taurus. SSID is “AP +last 8 digits of the SN”, for example, “AP10000033”.

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.063.3.2 WiFi Sta ModeNetwork DiagramUsers can access Taurus through external router when it is connected via WiFi Sta.ConfigurationStep 1 Refer to “6 General Operations” to log in to the Taurus.Step 2 Turn on Wi-Fi Sta mode. Click the Wi-Fi name of the external router and then enterthe password of the Wi-Fi.ViPlex Handy: Select Network Setting,WiFi Setting in the Screenmanagement page.ViPlex Express: Select Screen Control,Network configuration.3.3.3 WiFi AP+Sta ModeNetwork DiagramBy using WiFi AP+Sta connection, users can directly access the Taurus or access theInternet through bridging connection.

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.07ConfigurationStep 1 Refer to “6 General Operations” to log in to the Taurus.Step 2 Turn on Wi-Fi Sta mode. Click the Wi-Fi name of the external router and then enterthe password of the Wi-Fi.ViPlex Handy: Select Network Setting,WiFi Setting in the Screenmanagement page.ViPlex Express: Select Screen Control,Network configuration.Related InformationThe Taurus can be connected to the Internet through following two ways. The priorityorder of the three ways is from high to low.Wired networkWiFi Sta

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.084Receiving Card Parameter ConfigurationIf receiving card parameters are already configured, please skip this chapter andperform the operations in “5 Screen Configuration”.4.1 Loading Configuration File or Configuring theParameters Manually Through NovaLCT-TaurusStep 1 Start NovaLCT-Taurus.Step 2 Select System,Search All Display.System will display the screen information list.Step 3 Click screen information and click Connect System.The gray button on the page will become normal.Step 4 Select User,Advanced login.Step 5 Enter password and click Login.Default password is “admin”.Step 6 Click to enter the Screen Config page.Step 7 Confirm whether the local PC has the required receiving card configuration file.Yes. Please perform Load Configuration File.No. Please perform Manual Configuration.Loading Configuration FileStep 1 Select Cascading scan board and Load Configuration File. Click Browse tochoose a configuration file from the local PC.Step 2 Click Next to load the configuration file.Manual ConfigurationStep 1 Select Cascading scan board and click Next.Step 2 Configure receiving card parameters based on actual conditions.

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.09Step 3 Click Send To HW.Step 4 Set parameters based on actual conditions and click Send.Step 5 Adjust parameters until the screen displays normally and then click Save to Screen.Step 6 (Optional) Click Save Config File to back up the receiving card configuration file tothe local PC.4.2 Loading the Configuration File Through ViPlex HandyStep 1 Save the receiving card configuration file to mobile phone.Step 2 Refer to “6 General Operations” to log in to the Taurus.Step 3 Click screen name to enter the Screen management page.Step 4 Select Screen Setting,Receiving card configuration to enter the Receiving cardconfiguration page.Step 5 Select the receiving card configuration file and click Send.

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.0105Screen Configuration5.1 Configuring a Screen Through ViPlex HandyStep 1 Refer to “6 General Operations” to log in to the Taurus.Step 2 Click screen name to enter the Screen management page.Step 3 Select Screen Setting,Screen configuration to enter the Screen configurationpage.Step 4 Configure screen information based on actual conditions and click OK.

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.0116General Operations6.1 Taurus Login with ViPlex Handy (Android and iOS)Before You BeginAcquire the SSID and password of Wi-Fi AP of Taurus series products. SSID isdefault to be composed of AP and the last 8 numbers of SN, and the password isdefault as “12345678”.Acquire the login password of user “admin” of which the default password is“123456”.Operating ProceduresViPlex Handy can connect numerous Taurus series products.Step 1 Connect Wi-Fi AP of the Taurus series products.Step 2 Start ViPlex Handy.System can automatically detect the Taurus series products and refresh Screen list.Users can also slide down Screen list to manually refresh the list.: denotes that Taurus is online and you can log into it.: denotes that Taurus is offline and you cannot log into it.: denotes that Taurus login is successful.Step 3 Click Connect next to the screen name.Step 4 Enter the user name and password and click Login.6.2 Taurus Login with ViPlex Express (Windows)Before You BeginAcquire the SSID and password of Wi-Fi AP of Taurus series products. SSID isdefault to be composed of AP and the last 8 numbers of SN, and the password isdefault as “12345678”.Acquire the login password of user “admin” of which the default password is“123456”.

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.012Operating ProceduresViPlex Express can connect numerous Taurus series products.Step 1 Connect Wi-Fi AP of the Taurus series products.Step 2 Start the ViPlex Express.Step 3 Click Refresh and the screen list will be displayed on the page.: denotes that Taurus is online and you can log into it.: denotes that Taurus is offline and you cannot log into it.: denotes that Taurus login is successful.After the Taurus is found by ViPlex Express, the ViPlex express will try to log into tothe Taurus with the default account or the account used for last login.Step 4 Taurus login is successful or not.Yes. appears and no further operation is required.No. appears and then perform Step 5.Step 5 Click Connect on the right of the screen information.Step 6 Enter the username and password, and click OK.

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.0137CautionFCC Caution:Any changes or modifications not expressly approved by the party responsible for compliance couldvoid the user's authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class A digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference when the equipment is operated in a commercial environment. Thisequipment generates, uses, and can radiate radio frequency energy and, if not installed and used inaccordance with the instruction manual, may cause harmful interference to radio communications.Operation of this equipment in a residential area is likely to cause harmful interference in which case theuser will be required to correct the interference at his own expense.This equipment complies with FCC radiation exposure limits set forth for an uncontrolledenvironment .This equipment should be installed and operated with minimum distance 20cm betweenthe radiator & your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.CE Caution:This equipment should be installed and operated with minimum distance 20cm between the radiator &your body.IC Warning:RSS-Gen Issue 3 December 2010"&"CNR-Gen 3e éditionDécembre 2010:- English:This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation ofthe device.- French:Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exemptsde licence. L'exploitationestautorisée aux deux conditions suivantes:(1) l'appareil ne doit pas produire de brouillage, et

Taurus Series Multimedia PlayersQuick Start Guidewww.novastar.techV1.0.014(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageestsusceptible d'encompromettre le fonctionnement.Battery Caution:

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 正基正基正基正基科技股份有限公司科技股份有限公司科技股份有限公司科技股份有限公司 SPECIFICATION SPEC. NO.：：：： REV： 1.3 DATE：：：： 12. 26.2014 PRODUCT NAME：：：： AP6212 APPROVED CHECKED PREPARED DCC ISSUE NAME

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: AMPAK AP6212 WiFi+Bluetooth 4.1+FM RX SIP Module Spec Sheet

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 1 Revision History Date Revision Content Revised By Version 2014/04/08 - Preliminary Brian 1.0 2014/09/02 - Pin Definition Modified Brian 1.1 2014/11/26 - Bluetooth Spec Modified Brian 1.2 2014/12/26 - Add Process Brian 1.3

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 3 1. Introduction AMPAK Technology would like to announce a low-cost and low-power consumption module which has all of the WiFi, Bluetooth and FM functionalities. The highly integrated module makes the possibilities of web browsing, VoIP, Bluetooth headsets, FM radio functional applications and other applications. With seamless roaming capabilities and advanced security, also could interact with different vendors’ 802.11b/g/n Access Points in the wireless LAN. The wireless module complies with IEEE 802.11 b/g/n standard and it can achieve up to a speed of 72.2Mbps with single stream in 802.11n draft, 54Mbps as specified in IEEE 802.11g, or 11Mbps for IEEE 802.11b to connect to the wireless LAN. The integrated module provides SDIO interface for WiFi, UART / I2S / PCM interface for Bluetooth and UART / I2S / PCM interface for FM. This compact module is a total solution for a combination of WiFi + BT + FM technologies. The module is specifically developed for Smart phones and Portable devices.

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 4 2. Features  802.11b/g/n single-band radio  Bluetooth V4.1(HS) with integrated Class 1.5 PA and Low Energy (BLE) support  Concurrent Bluetooth, FM (RX) RDS/RBDS, and WLAN operation  Simultaneous BT/WLAN receive with single antenna  WLAN host interface options: - SDIO v2.0 — up to 50 MHz clock rate  BT host digital interface: - UART (up to 4 Mbps)  FM multiple audio routing options: I2S, PCM, eSCO, A2DP  IEEE Co-existence technologies are integrated die solution  ECI — enhanced coexistence support, ability to coordinate BT SCO transmissions around WLAN receives A simplified block diagram of the module is depicted in the figure below.

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 5 3. Deliverables 3.1 Deliverables The following products and software will be part of the product.  Module with packaging  Evaluation Kits  Software utility for integration, performance test.  Product Datasheet.  Agency certified pre-tested report with the adapter board. 3.2 Regulatory certifications The product delivery is a pre-tested module, without the module level certification. For module approval, the platform’s antennas are required for the certification.

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 6 4. General Specification 4.1 General Specification 4.2 Voltages 4.2.1 Absolute Maximum Ratings Symbol Description Min. Max. Unit VBAT Input supply Voltage -0.5 5.5 V WL_VIO_SD Digital/Bluetooth/SDIO/ I/O Voltage -0.5 3.6 V 4.2.2 Recommended Operating Rating The module requires two power supplies: VBAT and VDDIO. Min. Typ. Max. Unit Operating Temperature -30 25 85 deg.C VBAT 3.0 3.6 4.8 V VDDIO 1.7 3.3 3.6 V Model Name AP6212 Product Description Support WiFi/Bluetooth/FM functionalities Dimension L x W x H: 12 x 12 x 1.5 (typical) mm WiFi Interface SDIOV2.0 BT Interface UART / PCM FM Interface UART / PCM / Audio Operating temperature -30°C to 85°C Storage temperature -40°C to 85°C Humidity Operating Humidity 10% to 95% Non-Condensing Storage Humidity 5% to 95% Non-Condensing

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 7 5. WiFi RF Specification 5.1 2.4GHz RF Specification Conditions : VBAT=3.6V ; VDDIO=3.3V ; Temp:25°C Feature Description WLAN Standard IEEE 802.11b/g/n, WiFi compliant Frequency Range 2.400 GHz ~ 2.497 GHz (2.4 GHz ISM Band) Number of Channels 2.4GHz：Ch1 ~ Ch14 Modulation 802.11b : DQPSK, DBPSK, CCK 802.11 g/n : OFDM /64-QAM,16-QAM, QPSK, BPSK Output Power 802.11b /11Mbps : 16 dBm ± 1.5 dB @ EVM ≤ -9dB 802.11g /54Mbps : 15 dBm ± 1.5 dB @ EVM ≤ -25dB 802.11n /65Mbps : 14 dBm ± 1.5 dB @ EVM ≤ -28dB Receive Sensitivity (11n,20MHz) @10% PER - MCS=0 PER @ -85 dBm, typical - MCS=1 PER @ -84 dBm, typical - MCS=2 PER @ -82 dBm, typical - MCS=3 PER @ -80 dBm, typical - MCS=4 PER @ -77 dBm, typical - MCS=5 PER @ -73 dBm, typical - MCS=6 PER @ -71 dBm, typical - MCS=7 PER @ -68 dBm, typical Receive Sensitivity (11g) @10% PER - 6Mbps PER @ -86 dBm, typical - 9Mbps PER @ -85 dBm, typical - 12Mbps PER @ -85 dBm, typical - 18Mbps PER @ -83 dBm, typical - 24Mbps PER @ -81 dBm, typical - 36Mbps PER @ -78 dBm, typical - 48Mbps PER @ -73 dBm, typical - 54Mbps PER @ -71 dBm, typical Receive Sensitivity (11b) @8% PER - 1Mbps PER @ -90 dBm, typical - 2Mbps PER @ -88 dBm, typical - 5.5Mbps PER @ -87 dBm, typical - 11Mbps PER @ -84 dBm, typical Data Rate 802.11b : 1, 2, 5.5, 11Mbps 802.11g : 6, 9, 12, 18, 24, 36, 48, 54Mbps

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 8 Data Rate (20MHz ,Long GI,800ns) 802.11n: 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps Data Rate (20MHz ,short GI,400ns) 802.11n : 7.2, 14.4, 21.7, 28.9, 43.3, 57.8, 65,72.2Mbps Maximum Input Level 802.11b : -10 dBm 802.11g/n : -20 dBm Antenna Reference Small antennas with 0~2 dBi peak gain

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 9 6. Bluetooth Specification 6.1 Bluetooth Specification Conditions : VBAT=3.6V ; VDDIO=3.3V ; Temp:25°C Feature Description General Specification Bluetooth Standard Bluetooth V4.1 of 1, 2 and 3 Mbps. Host Interface UART Antenna Reference Small antennas with 0~2 dBi peak gain Frequency Band 2402MHz ~ 2480MHz Number of Channels 79 channels Modulation FHSS, GFSK, DPSK, DQPSK RF Specification Min. Typical. Max. Output Power (Class 1.5) 8 dBm Sensitivity @ BER=0.1% for GFSK (1Mbps) -86 dBm Sensitivity @ BER=0.01% for π/4-DQPSK (2Mbps) -86 dBm Sensitivity @ BER=0.01% for 8DPSK (3Mbps) -80 dBm Maximum Input Level GFSK (1Mbps):-20dBm π/4-DQPSK (2Mbps) :-20dBm 8DPSK (3Mbps) :-20dBm

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 107. FM Specification 7.1 FM Specification (TBD) Conditions : VBAT=3.6V ; VDDIO=3.3V ; Temp:25°C Feature Description General Specification Frequency Band 76MHz-108MHz Host Interface HCI UART, I2S/PCM Channel step 50 KHz Analog Audio output load RL>30KΩ, CL>20pF Characteristics Condition MIN TYP MAX UNIT Transmitter (FM Tx load = 120nH, Q>30) Output Power Level dBuV Audio harmonic distortion (fmod=1KHz, △f=75KHz, Pilot △f=6.75KHz) % Audio SNR (△f=22.5KHz, I2S audio in SNR ≧57dB ) MONO dB Stereo Receiver (FM Tx Antenna = 120nH, Q>30) RDS Sensitivity dBm Audio harmonic distortion (Vin=1mV, △f=75KHz) fmod=1KHz % fmod=3KHz Maximum SNR (fmod=1KHz, f=22.5KHz, BW=300Hz to 15KHz) MONO dB Stereo RF input power level dBuV

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 118. Pin Assignments 8.1 Pin Outline < TOP VIEW > 8.2 Pin Definition NO Name Type Description 1 GND － Ground connections 2 WL_BT_ANT I/O RF I/O port 3 GND － Ground connections 4 FM_RX I FM radio RF input antenna port 5 NC － Floating (Don’t connected to ground) 6 BT_WAKE I HOST wake-up Bluetooth device 7 BT_HOST_WAKE O Bluetooth device to wake-up HOST 8 NC － Floating (Don’t connected to ground) 9 VBAT P Main power voltage source input 10 XTAL_IN I Crystal input 11 XTAL_OUT O Crystal output 12 WL_REG_ON I Internal regulators power enable/disable 13 WL_HOST_WAKE O WLAN to wake-up HOST

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 1214 SDIO_DATA_2 I/O SDIO data line 2 15 SDIO_DATA_3 I/O SDIO data line 3 16 SDIO_DATA_CMD I/O SDIO command line 17 SDIO_DATA_CLK I/O SDIO clock line 18 SDIO_DATA_0 I/O SDIO data line 0 19 SDIO_DATA_1 I/O SDIO data line 1 20 GND － Ground connections 21 VIN_LDO_OUT P Internal Buck voltage generation pin 22 VDDIO P I/O Voltage supply input 23 VIN_LDO P Internal Buck voltage generation pin 24 LPO I External Low Power Clock input (32.768KHz) 25 PCM_OUT O PCM Data output 26 PCM_CLK I/O PCM clock 27 PCM_IN I PCM data input 28 PCM_SYNC I/O PCM sync signal 29 NC － Floating (Don’t connected to ground) 30 NC － Floating (Don’t connected to ground) 31 GND － Ground connections 32 NC － Floating (Don’t connected to ground) 33 GND － Ground connections 34 BT_RST_N I Low asserting reset for Bluetooth core 35 NC － Floating (Don’t connected to ground) 36 GND － Ground connections 37 GPIO4 I/O WiFi Co-existence pin with LTE 38 GPIO3 I/O WiFi Co-existence pin with LTE 39 GPIO2 I/O WiFi Co-existence pin with LTE 40 GPIO1 I/O WiFi Co-existence pin with LTE 41 UART_RTS_N O Bluetooth/FM UART interface 42 UART_TXD O Bluetooth/FM UART interface 43 UART_RXD I Bluetooth/FM UART interface 44 UART_CTS_N I Bluetooth/FM UART interface 45 TP1 O FM Analog AUDIO left output 46 TP2 O FM Analog AUDIO right output 47 TP3 (NC) － Floating (Don’t connected to ground)

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 139. Dimensions 9.1 Physical Dimensions (Unit: mm) < TOP VIEW > < Side View > < TOP VIEW >

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 149.2 Layout Recommendation (Unit: mm) < TOP VIEW >

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 1510. External clock reference External LPO signal characteristics Parameter Specification Units Nominal input frequency 32.768 kHz Frequency accuracy 30± ppm Duty cycle 30 - 70 % Input signal amplitude 400 to 1800 mV, p-p Signal type Square-wave - Input impedance >100k <5 Ω pF Clock jitter (integrated over 300Hz – 15KHz) <1 Hz Output high voltage 0.7Vio - Vio V External Ref_CLK signal characteristics 10.1 SDIO Pin Description The module supports SDIO version 2.0 for 4-bit modes (100 Mbps), and high speed 4-bit (50 MHz clocks – 200 Mbps). It has the ability to stop the SDIO clock and map the interrupt signal into a GPIO pin. This ‘out-of-band’ interrupt signal notifies the host when the WLAN device wants to turn on the SDIO interface. The ability to force the control of the gated clocks from within the WLAN chip is also provided.

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 16 Function 0 Standard SDIO function (Max BlockSize / ByteCount = 32B)  Function 1 Backplane Function to access the internal System On Chip (SOC) address space (Max BlockSize / ByteCount = 64B)  Function 2 WLAN Function for efficient WLAN packet transfer through DMA (Max BlockSize/ByteCount=512B) SDIO Pin Description SD 4-Bit Mode DATA0 Data Line 0 DATA1 Data Line 1 or Interrupt DATA2 Data Line 2 or Read Wait DATA3 Data Line 3 CLK Clock CMD Command Line 11. Host Interface Timing Diagram 11.1 Power-up Sequence Timing Diagram The module has signals that allow the host to control power consumption by enabling or disabling the Bluetooth, WLAN and internal regulator blocks. These signals are described below. Additionally, diagrams are provided to indicate proper sequencing of the signals for carious operating states. The timing value indicated are minimum required values: longer delays are also acceptable. ※ WL_REG_ON: Used by the PMU to power up the WLAN section. When this pin is high, the regulators are enabled and the WLAN section is out of reset. When this pin is low the WLAN section is in reset. ※ BT_RST_N: Low asserting reset for Bluetooth and FM only. This pin has no effect on WLAN and does not control any PMU functions. This pin must be driven high or low (not left floating).

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 17 WLAN=ON, Bluetooth=ON WLAN=OFF, Bluetooth=OFF WLAN=ON, Bluetooth=OFF

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 18 WLAN=OFF, Bluetooth=ON 11.2 SDIO Default Mode Timing Diagram

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 19 11.3 SDIO High Speed Mode Timing Diagram

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 21Solder Paste definition

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 2213. Package Information 13.1Label Label A Anti-static and humidity notice Label B MSL caution / Storage Condition Label C Inner box label . Label D Carton box label .

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 2313.2 Dimension

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 24 A B C Humidity indicator Desiccant C D

AP6212 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 2513.3 MSL Level / Storage Condition ※※※※NOTE : Accumulated baking time should not exceed 96hrs

RTL8188EUS SINGLE-CHIP IEEE 802.11b/g/n 1T1R WLAN DATASHEET (CONFIDENTIAL: Development Partners Only) Rev. 0.2 27 Mar. 2012 Track ID: Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, TaiwanTel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.com Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet COPYRIGHT ©2011 Realtek Semiconductor Corp. All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of Realtek Semiconductor Corp. DISCLAIMER Realtek provides this document “as is”, without warranty of any kind. Realtek may make improvements and/or changes in this document or in the product described in this document at any time. This document could include technical inaccuracies or typographical errors. TRADEMARKS Realtek is a trademark of Realtek Semiconductor Corporation. Other names mentioned in this document are trademarks/registered trademarks of their respective owners. USING THIS DOCUMENT This document is intended for the software engineer’s reference and provides detailed programming information. Though every effort has been made to ensure that this document is current and accurate, more information may have become available subsequent to the production of this guide. REVISION HISTORY Revision Release Date Summary 0.2 2012/3/27 Preliminary release Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller ii Track ID: JATR-2265-11 Rev. 0.5with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet Table of Contents 1.GENERAL DESCRIPTION ...............................................................................................................................................12.FEATURES ..........................................................................................................................................................................33.APPLICATION DIAGRAM...............................................................................................................................................53.1.SINGLE-BAND 11N (1X1) SOLUTION WITH SINGLE ANTENNA .........................................................................................53.2.SINGLE-BAND 11N (1X1) SOLUTION WITH DUAL ANTENNA DIVERSITY .........................................................................63.3.SINGLE-BAND 11N (1X1) SOLUTION WITH DUAL ANTENNA............................................................................................64.PIN ASSIGNMENTS...........................................................................................................................................................74.1.PACKAGE IDENTIFICATION..............................................................................................................................................75.PIN DESCRIPTIONS..........................................................................................................................................................75.1.USB BUS TRANSCEIVER INTERFACE...............................................................................................................................85.2.POWER PINS ....................................................................................................................................................................85.3.RF INTERFACE ................................................................................................................................................................85.4.LED INTERFACE..............................................................................................................................................................95.5.CLOCK AND OTHER PINS...............................................................................................................................................106.ELECTRICAL AND THERMAL CHARACTERISTICS.............................................................................................116.1.TEMPERATURE LIMIT RATINGS .....................................................................................................................................116.2.DC CHARACTERISTICS ..................................................................................................................................................116.2.1.Power Supply Characteristics.............................................................................................................................116.2.2.Digital IO Pin DC Characteristics.......................................................................................................................117.INTERFACE TIMING SPECIFICATION .....................................................................................................................137.1.USB BUS DURING POWER ON SEQUENCE .....................................................................................................................138.MECHANICAL DIMENSIONS.......................................................................................................................................148.1.MECHANICAL DIMENSIONS NOTES ...............................................................................................................................149.ORDERING INFORMATION.........................................................................................................................................15 Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller iii Track ID: JATR-2265-11 Rev. 0.5with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet List of Tables TABLE 1. USB BUS TRANSCEIVER INTERFACE...............................................................................................................................8TABLE 2. POWER PINS ...................................................................................................................................................................8TABLE 3. RF INTERFACE ...............................................................................................................................................................8TABLE 4. LED INTERFACE.............................................................................................................................................................9TABLE 5. CLOCK AND OTHER PINS..............................................................................................................................................10TABLE 6.TEMPERATURE LIMIT RATINGS .................................................................................................................................11TABLE 7.DC CHARACTERISTICS ..............................................................................................................................................11TABLE 8.3.3V GPIO DC CHARACTERISTICS ...........................................................................................................................11TABLE 9.2.8V GPIO DC CHARACTERISTICS ...........................................................................................................................11TABLE 10.1.8V GPIO DC CHARACTERISTICS .......................................................................................................................12TABLE 11.THE TYPICAL TIMING RANGE .................................................................................................................................13TABLE 12.ORDERING INFORMATION......................................................................................................................................15 List of Figures FIGURE 1. SINGLE-BAND 11N (1X1) SOLUTION...............................................................................................................................5FIGURE 2. SINGLE-BAND 11N (1X1) DUAL ANTENNA DIVERSITY SOLUTION....................................................................................6FIGURE 3. SINGLE-BAND 11N (1X1) DUAL ANTENNA SOLUTION .....................................................................................................6FIGURE 4. PIN ASSIGNMENTS ..........................................................................................................................................................7FIGURE 5. RTL8188EUS USB BUS POWER ON SEQUENCE ..........................................................................................................13 Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller iv Track ID: JATR-2265-11 Rev. 0.5with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet 1. General Description The Realtek RTL8188EUS is a highly integrated single-chip 802.11n Wireless LAN (WLAN) network USB interface (USB 1.0/1.1/2.0 compliant) controller. It combines a WLAN MAC, a 1T1R capable WLAN baseband, and WLAN RF in a single chip. The RTL8188EUS provides a complete solution for a high throughput performance integrated wireless LAN device. The RTL8188EUS WLAN baseband implements Orthogonal Frequency Division Multiplexing (OFDM) with 1 transmit and 1 receive path and is compatible with the IEEE 802.11n specification. Features include one spatial stream transmission, short guard interval (GI) of 400ns, spatial spreading, and transmission over 20MHz and 40MHz bandwidth. For legacy compatibility, Direct Sequence Spread Spectrum (DSSS), Complementary Code Keying (CCK) and OFDM baseband processing are included to support all IEEE 802.11b and 802.11g data rates. Differential phase shift keying modulation schemes, DBPSK and DQPSK with data scrambling capability, are available, and CCK provides support for legacy data rates, with long or short preamble. The high-speed FFT/IFFT paths, combined with BPSK, QPSK, 16QAM, and 64QAM modulation of the individual subcarriers and rate compatible punctured convolutional coding with coding rate of 1/2, 2/3, 3/4, and 5/6, provide higher data rates of 54Mbps and 150Mbps for IEEE 802.11g and 802.11n OFDM respectively. The RTL8188EUS WLAN Controller builds in an enhanced signal detector, an adaptive frequency domain equalizer, and a soft-decision Viterbi decoder to alleviate severe multi-path effects and mutual interference in the reception of multiple streams. Efficient IQ-imbalance, DC offset, phase noise, frequency offset, and timing offset compensations are provided for the radio frequency front-end. Selectable digital transmit and receive FIR filters are provided to meet transmit spectrum mask requirements and to reject adjacent channel interference, respectively. The RTL8188EUS WLAN Controller supports fast receiver Automatic Gain Control (AGC) with synchronous and asynchronous control loops among antennas, antenna diversity functions, and adaptive transmit power control function to obtain the better performance in the analog portions of the transceiver. The RTL8188EUS WLAN MAC supports 802.11e for multimedia applications, 802.11i for security, and 802.11n for enhanced MAC protocol efficiency. Using packet aggregation techniques such as A-MPDU Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 1 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet with BA and A-MSDU, protocol efficiency is significantly improved. Power saving mechanisms such as Legacy Power Save, and U-APSD, reduce the power wasted during idle time, and compensates for the extra power required to transmit OFDM. The RTL8188EUS provides simple legacy and 20MHz/40MHz co-existence mechanisms to ensure backward and network compatibility. Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 2 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet 2. Features General  46-pin QFN  CMOS MAC, Baseband PHY, and RF in a single chip for IEEE 802.11b/g/n compatible WLAN  Complete 802.11n solution for 2.4GHz band  72.2Mbps receive PHY rate and 72.2Mbps transmit PHY rate using 20MHz bandwidth  150Mbps receive PHY rate and 150Mbps transmit PHY rate using 40MHz bandwidth  Compatible with 802.11n specification  Backward compatible with 802.11b/g devices while operating in 802.11n mode Interface  Complies with USB 1.0/1.1/2.0 for WLAN Standards Supported  IEEE 802.11b/g/n compatible WLAN  IEEE 802.11e QoS Enhancement (WMM)  802.11i (WPA, WPA2). Open, shared key, and pair-wise key authentication services WLAN MAC Features  Frame aggregation for increased MAC efficiency (A-MSDU, A-MPDU)  Low latency immediate High-Throughput Block Acknowledgement (HT-BA)  PHY-level spoofing to enhance legacy compatibility  Power saving mechanism  Channel management and co-existence  Transmit Opportunity (TXOP) Short Inter-Frame Space (SIFS) bursting for higher multimedia bandwidth WLAN PHY Features  IEEE 802.11n OFDM  One Transmit and one Receive path (1T1R)  20MHz and 40MHz bandwidth transmission  Short Guard Interval (400ns)  DSSS with DBPSK and DQPSK, CCK modulation with long and short preamble  OFDM with BPSK, QPSK, 16QAM, and 64QAM modulation. Convolutional Coding Rate: 1/2, 2/3, 3/4, and 5/6  Maximum data rate 54Mbps in 802.11g and 150Mbps in 802.11n  Hardware antenna diversity in per packet base  Selectable receiver FIR filters  Programmable scaling in transmitter and receiver to trade quantization noise against increased probability of clipping  Fast receiver Automatic Gain Control (AGC)  On-chip ADC and DAC Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 3 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet Peripheral Interfaces  General Purpose Input/Output (8 pins)  Three configurable LED pins Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 4 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet 3. Application Diagram 3.1. Single-Band 11n (1x1) Solution with Single Antenna Figure 1. Single-Band 11n (1x1) Solution Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 5 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet 3.2. Single-Band 11n (1x1) Solution with Transmit & Receive Diversity Figure 2. Single-Band 11n (1x1) Transmit & Receive Diversity solution 3.3. Single-Band 11n (1x1) Solution with Transmit & Receive Diversity Figure 3. Single-Band 11n (1x1) Transmit & Receive Diversity sSolution Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 6 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet 4. Pin Assignments 23212019181716151413121110223334353637383940414243454644NCXIANT_SEL_N/LED1NCVD12AXOGPIO[8]/CK_OUTNCGNDLX_SPSVD33AANT_SEL_2VD12DGPIO[3]/BT_PRISPS/LD0_SEL/GPIO[1]TRSWPGPIO[0]/WLAN_ACTGPIO[2]/BT_STATEVD33DVD33DVD12DNCGPIO[7]GPIO[4]TRSWNVD33D GPIO[5]/LED2ANT_SEL_P/LED0 Figure 4. Pin Assignments 4.1. Package Identification ‘Green’ package is indicated by a ‘G’ in the location marked ‘T’ in Figure 4. 5. Pin Descriptions The following signal type codes are used in the tables: I: Input O: Output T/S: Tri-State bi-directional input/output pin S/T/S: Sustained Tri-State Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 7 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet O/D: Open Drain P: Power pin 5.1. USB Bus Transceiver Interface Table 1. USB bus Transceiver Interface Symbol Type Pin No Description HSDM/HSDP I 27/26 USB Receive Differential Pair 5.2. Power Pins Table 2. Power Pins Symbol Type Pin No Description LX_SPS P 22 Switching Regulator Output VD33A P 4,9,12, VDD 3.3V for Analog VD33D P 23,28,40,41 VDD 3.3V for Digital VD12A P 7,8,13,25 Analog 1.2V Regulator Output VD12D P 17,42 Digital 1.2V Regulator Output GND P 21,47 Ground 5.3. RF Interface Table 3. RF Interface Symbol Type Pin No Description TRSWN O 45 Transmit/Receive Shared with LED2, can be selected by control register PAPE O 1 2.4GHz Transmit Power Amplifier Power Enable 0 TRSWP O 46 Transmit/Receive TXPA_OP O 2 RF TX Negative Signal TXPA_ON O 3 RF TX Positive Signal RX_IP I 5 RF RX Positive Signal RX_IN I 6 RF RX Negative Signal ANT_SEL_P O 44 Antenna Control Positive Signal Shared with LED0, can be selected by control register ANT_SEL_N O 15 Antenna Control Negative Signal Shared with LED1, can be selected by control register ANT_SEL_2 O 16 Antenna Control Extend Signal Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 8 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet 5.4. LED Interface Table 4. LED Interface Symbol Type Pin No Description LED0 O 44 LED Pins (Active Low) Shared with ANT_SEL_P, can be selected by control register LED1 O 15 LED Pins (Active Low) Shared with ANT_SEL_N, can be selected by control register LED2 O 33 LED Pins (Active Low) Shared with GPIO5, can be selected by control register Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 9 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet 5.5. Clock and Other Pins Table 5. Clock and Other Pins Symbol Type Pin No Description XI I 11 25/40MHz OSC Input Input of 25/40MHz Crystal clock reference XO O 10 Output of 25/40MHz Crystal Clock Reference PDn I 32 This Pin can Externally Shutdown RTL8188CE without Extra Power SwitchREXT O 24 Band gap. It needs to link 24k resister pull down. USB_XTAL_SEL I 30 Trap Function: Decide to use the 25/40Mhz crystal by this pin power on latch low or high. USB_XTAL_SEL = 1, XTAL frequency is 40MHz USB_XTAL_SEL = 0, XTAL frequency is 25MHz GPIO0/WLAN_ACT IO 36 General Purpose Input/Output Pin or Bluetooth Coexistence WLAN_ACT Pin The WLAN_ACT signal indicates when WLAN is either transmitting or receiving in the 2.4GHz ISM band. GPIO1/ (SPS/LDO_SEL mode) IO 39 Trap Function: Decide to use the SWR or LDO for 3.3V -> 1.2V by this pin power on latch low or high. LDO_SPS_SEL = 0, use SWR LDO_SPS_SEL = 1, use LDO General Purpose Input/Output Pin or Bluetooth Coexistence WLAN_RX Pin. GPIO2/BT_STATE IO 37 General Purpose Input/Output Pin or Bluetooth Coexistence BT_STAT PinThe BTSTAT signal indicates when normal Bluetooth packets are being transmitted or received. GPIO3/BT_PRI IO 38 General Purpose Input/Output Pin or Bluetooth Coexistence BT_PRI Pin The BTPRI signal indicates when a high priority Bluetooth packet is being transmitted or received. GPIO4 IO 35 General Purpose Input/Output Pin GPIO5/LED2 IO 33 General Purpose Input/Output Pin Shared with LED2, can be selected by control register GPIO7 IO 34 This pin can also support WLAN Radio off function with host interface remaining connected. GPIO8/CK_OUT IO 14 General Purpose Input/Output Pin Buffered 25/40M clock outputs for other peripheral IC NC NA 18,19,20,29,31, 43 No connect. Let it open. Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 10 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet 6. Electrical and Thermal Characteristics 6.1. Temperature Limit Ratings Table 6. Temperature Limit Ratings Parameter Minimum Maximum Units Storage Temperature -55 +125 °C Ambient Operating Temperature 0 70 °C Junction Temperature 0 125 °C 6.2. DC Characteristics 6.2.1. Power Supply Characteristics Table 7. DC Characteristics Symbol Parameter Minimum Typical Maximum Units VD33A, VD33D 3.3V I/O Supply Voltage 3.0 3.3 3.6 V VD12A, VD12D 1.2V Core Supply Voltage 1.10 1.2 1.32 V VD15A, VD15D 1.5V Supply Voltage 1.425 1.5 1.575 V IDD33 3.3V Rating Current - - 600 mA 6.2.2. Digital IO Pin DC Characteristics Table 8. 3.3V GPIO DC Characteristics Symbol Parameter Minimum Normal Maximum Units VIH Input high voltage 2.0 3.3 3.6 V VIL Input low voltage -- 0 0.9 V VOH Output high voltage 2.97 -- 3.3 V VOL Output low voltage 0 -- 0.33 V Table 9. 2.8V GPIO DC Characteristics Symbol Parameter Minimum Normal Maximum Units VIH Input high voltage 1.8 2.8 3.1 V VIL Input low voltage -- 0 0.8 V VOH Output high voltage 2.5 -- 3.1 V VOL Output low voltage 0 -- 0.28 V Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 11 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet Table 10. 1.8V GPIO DC Characteristics Symbol Parameter Minimum Normal Maximum Units VIH Input high voltage 1.7 1.8 2.0 V VIL Input low voltage -- 0 0.8 V VOH Output high voltage 1.62 -- 1.8 V VOL Output low voltage 0 -- 0.18 V Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 12 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet 7. Interface Timing Specification 7.1. USB Bus during Power On Sequence 3.3VTonTPORTattachTk-stateCard DetectionD+D-SE0 ResetPOR Figure 5. RTL8188EUS USB Bus Power On Sequence Ton: The main power ramp up duration Tpor: The power on reset releases and power management unit executes power on tasks Tattach: USB attach state Tk-state: the duration from resister attached to USB host starting card detection procedure The power on flow description: After main 3.3V ramp up, the internal power on reset is released by power ready detection circuit and the power management unit will be enabled. The power management unit enables the internal regulator and clock circuits. The power management unit also enables the USB circuits. USB analog circuits attach resisters to indicate the insertion of the USB device Table 11. The typical timing range Unit Min Typical Max Ton ms -- 1.5 5 Tpor ms -- 2 10 Tattach ms 2 7 15 Tk-state ms 50 250 -- Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 13 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet 8. Mechanical Dimensions 8.1. Mechanical Dimensions Notes Dimension in mm Dimension in inch Symbol Min Nom Max Min Nom Max A 0.75 0.85 1.00 0.030 0.034 0.039 A10.00 0.035 0.05 0.000 0.001 0.002 A20.55 0.65 0.80 0.022 0.026 0.032 A30.20 REF 0.008 REF b 0.15 0.20 0.25 0.006 0.008 0.010 D 6.50BSC 0.256BSC D2 4.85 5.1 5.35 0.191 0.201 0.211 E 4.5BSC 0.177BSC E2 2.25 2.5 2.75 0.088 0.098 0.108 e 0.40BSC 0.016BSC L 0.30 0.40 0.50 0.012 0.016 0.020 Notes： 1. CONTROLLING DIMENSION：MILLIMETER(mm). 2. REFERENCE DOCUMENTL：JEDEC MO-220. Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 14 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

RTL8188EUS Datasheet 9. Ordering Information Table 12. Ordering Information Part Number Package Status RTL8188EUS-CG QFN-46, ‘Green’ Package Engineering Samples Note: See page 7 for package identification. Realtek Semiconductor Corp. Headquarters No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan, R.O.C. Tel: 886-3-5780211 Fax: 886-3-5776047 www.realtek.com Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller 15 Track ID: JATR-2265-11 Rev. 0.1with USB Interface Realtek confidential filesThe document authorized toG.M.I2012-05-21 17:34:48

Navigation menu