XAC Automation AP10 PINPAD User Manual

XAC Automation Corporation PINPAD

User Manual

d INSTLAX TALLATIOA PAYMENXCL_APON GUIDENT DEVICEP-10E
1. PACKAGE CONTENT 2. DEVICE OVERVIEW xCL_AP‐10(hereundercalledAP‐10)KeyButtons&InterfacePorts(Figure1): Figure1 FRONTAREA1 4” TFT Color Display (480 x 800 pixel) 2 Rubber Keypad 3 Smart Card Reader (SCR) slot 4 Magnetic Strip Reader (MSR) slot REARAREA5 USB cable (type A) 6 SAM Compartment ■ AP-10 power spec: z PowerInput:5VDC,2Az OperatingTemperature:0oCto40oCFRONTREAR xCL_AP-10  Privacy Shield (Optional)
WARCCa3. POWERTopoweterminal Note:Aftpow4. USING TSwipethdisplay.( RNING:1.Theequipmentistrainingorexperienenergiesandenergy2.Theequipmentisportthatthatoutpu60950‐1/EN60590‐Caution:UseonlytheACwiththisdeviceaution:RiskofexplosiobatteryaccordingR ON/OFF THE Dronthedevice,pleorPOS.terbootingupAP‐10,wersavingmode.PleaTHE MAGNETICecardthroughthesFigure2)sintendedtobeinstallnceintheequipmentmagnitudesusedintheintendedtobesuppliedutcomplieswiththere‐1/UL60590‐1/CSA60Cadapterapprovedandonifthebatteryisreplagtotheinstructions.DEVICE aseplugtheUSBcaifisnoactiononAP‐aseshortpressanyb CARD READERslotwithmagneticsFigure2edbyskilledpersonortechnology,particularleequipmentandhostdedbyahostdevice(PCoequirementoftheLim0950‐1providedbyXACAutomacedbyanincorrecttypabletypeAintothe‐10after60seconds,uttononkeypadtowR stripesidefacingthe rservicepersonwhohayinknowingthevarioevice.orterminaldevice)viaUitedPowerSourceofmationCorporationforupe.PleasedisposeofusUSBportofyourhothedevicewillenterwakeupthedevice. esamedirectionastaveousUSBIECusesedostthe
5. USING THE IC CARD READER InsertanICcardintotheslot(Figure3)withthechipsidefacingupwardasthedisplay(Figure4). Figure3Figure46. USING THE KEY PAD Afterinsertingthechipcard,Pressthenumerickeyasbelowkeypad(Figure5)toenterthedesirablenumbers.PressCancel(X)keytoterminateanycurrentoperationorpresstheEnter(O)keytoconfirmavalueoranoption. Figure57. USING THE CONTACTLESS CARD READER Tapthecontactlesscardontopofthecontactlesslogo(Figure6). Figure6
9. INSERT SIM & SAM CARD ToremovetheSAMcardcompartmentbyunlockingthescrewM1.6*3pieces,pleaseusethescrewdrivertype0(Figure7),Afterremovingthecover,theusercanfindSAM*2slotsatthebottomsideofdevice.Pleaseinsertthecardcorrectlyastheiconshownonthecover(Figure8):Figure7Figure8Caution:Whenremovingrearcover(Figure7)forthepurposesofSAMcardinstallation,remembertoreinstallationtheprotectivecoverandmakesuretokeepitinplaceduringnormaloperation.9. INSTALL PRIVACY SHIELD (OPTIONAL ACCESSORY) PleaserefertoFigure9for2stepstoinstalltheshield:Step1:AlignandinserttwohooksofprivacyshieldwiththeslotonAP‐10device(filledbyrubber).Step2:Pushdownthebottomsideofshieldtocombinewiththedevice.AndtheoutlookisthesameasFigure10. Figure9Figure10
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RadiationExposureStatement:The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be disclosed, distributed or reproduced without permission of XAC Automation Corporation. XAC Automation Corporation 886-3-577-2738

Navigation menu