Woori Technology AVR7300 AV Receiver User Manual AVR7300 120v OM
Woori Technology Inc AV Receiver AVR7300 120v OM
UserManual.wiki
>
Woori Technology
>
AVR7300 User Manual
users manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![20 INSTALLATION AND CONNECTIONSINSTALLATION AND CONNECTIONSOption 2: Connect the Multiroom Audio Outputsøon the DPR 2005 to the inputs of an optionalstereo power amplifier. Run high-quality speaker wirefrom the amplifier to the speakers in the remote room.Option 3: Taking advantage of the AVR 7300’s built-in seven-channel amplifier, it is possible to use two ofthe amplifier channels to power speakers in the remoteroom.When using this option you will not be able touse the full 7.1-channel capabilities of the AVR 7300in the main listening room, but you will be able to add another listening room without external poweramplifiers.To use the internal amplifiers to power aremote zone,connect the speakers for the remoteroom location to the Surround Back/MultiroomSpeaker Outputs ç.Before using the remote roomyou will need to configure the amplifiers for surroundoperation by changing a setting (following the instruc-tions shown on page 39) in the MULTI-ROOMSETUP menu.NOTE: For all options, you may connect an optional IRsensor in the remote room to the AVR 7300 via anappropriate cable.Connect the sensor’s cable to theMultiroom IR Input Don the AVR 7300 anduse the Zone II remote to control the room volume.Alter-natively, you may install an optional volume con-trol between the output of the amplifiers and thespeakers.Multiroom Video ConnectionsThe AVR 7300’s multiroom system is designed tosend both video and audio signals to a remote roomlocation.This may be the same source that is in use in the main room, or you may select a separate inputsource through the Multiroom menus or remote,asexplained on page xx.The only additional connection required to add videocapabilities to your multiroom system is to connect theMultiroom Video Outputs [square O] either directly tothe video display in the remote room or to any option-al video distribution amplifiers that may be requiredwhen the length of the connection cable is such thatadditional amplification is required.The following items may be of additional assistancewhen using video as part of a multiroom system withthe AVR 7300:• When connecting the AVR 7300 to a “digital ready”,“HDTV compatible” or High Definition display,which isany device capable of accepting an input signal of480P or higher, you are able to take advantage ofthe unit’s advanced video processing circuitry con-verts all incoming video signals,regardless of the waythey are connected to the AVR. Since the AVR 7300is also among the very few products that display theon-screen menus with up-converted video,the con-nection from the AVR 7300 to the display need onlybe one set of Y/Pr/Pb component video cables.• Component video sources may not be routed throughthe multi-room system.When using a component videodevice,you should also make a composite or S-Videoconnection to permit use of the multiroom system.• As with all cable installations,when running any wiringinside a wall be certain that the cable carries the prop-er NEC rating for the application.The use of improper-ly rated cables may present a safety hazard.Consult a qualified installer or licensed electrician should youhave any questions about the use of in-wall cables for video or audio.A-BUS®Installation ConnectionsThe AVR 7300 is among the very few receivers avail-able today that offer built-in A-BUS Ready operation.When used with an optional A-BUS keypad or controlmodule,you have all the benefits of remote zoneoperation without the need for an external poweramplifier.To use the AVR 7300 with an approved A-BUS prod-uct, simply connect the keypad or module that is inthe remote room to the AVR 7300 using standardCategory 5 wiring that is properly rated for the in-walluse specific to the installation.Terminate the wiring at the receiver end to a standard RJ-45 connector incompliance with the instructions furnished with the A-BUS module.No further installation or adjustment is needed, as theA-BUS jacks on the AVR 7300 routes the signals inand out of the keypad to their proper destination forpower, signal source and control.The output fed to the A-BUS jack is determined by the AVR 7300’s mul-tiroom system and menus.RS-232 ConnectionsThe AVR 7300 is equipped with an RS-232 Port Sthat may be used for two purposes.When the port isconnected to a compatible,optional, external computer,keypad or control system the AVR 7300 is capable ofbi-directional communications that enable the externalsystem to control the AVR, and for the AVR to reportstatus and handshake data back to the controller. Useof the RS-232 port for this type of control requiresspecific technical knowledge,and we recommend thatany connection and programming for control be madeby a trained installer or technician familiar with theequipment being used.The RS-232 port may also be used as an accesspoint through which the AVR 7300’s operating systemand surround mode memories may be updated viaconnection to a compatible computer.At the time that an upgrade is available,instructions for making theconnection and installing the upgrade will be available through the Product Support area of theHarman Kardon Web site at harmankardon.com.The physical connection to the AVR 7300’s RS-232port is a standard D-SUB 9 connection but to assurecompatible and proper operation, specific softwarecommands and pin wiring schemes may be required.Trigger Jack ConnectionThe AVR 7300 is equipped with a low voltage triggerjack that may be used to activate optional, externalpower amplifiers,screen motors, motorized blinds orother compatible products that may be part of a hometheater installation. Once the connections are made,operation is seamless in that the low voltage controlsignal is sent to the screen, blinds or other devicewhen the AVR 7300 is turned on, and it is turned offalong with the AVR. Due to the complexity of inter-facing with power-controlled devices,we strong-ly recommend that the installation be done by aqualified installer.The AVR 7300’s trigger jack is a 3.5mm mono mini-plugthat delivers a 6 volt DC signal to the center pin ("tip") ofthe plug ("+") with the outer shaft (‘ring") of the plug asthe negative ("-") or ground connection.After checking forpolarity, voltage and current draw compatibility betweenthe AVR and the product to be controlled,simply connectthe mini plug to the Trigger Jack [square A] on one endand to the device to be controlled on the other.No furtherprogramming is required.The Switched AC Accessory Outlet dis poweredonly when the unit is on.This is recommended fordevices that have a mechanical power switch that maybe left in the “ON” position.NOTE: Many audio and video products go into aStandby mode when they are used with switched out-lets.This type of product may not operate properlywhen used with the switched outlet.The Unswitched AC Accessory Outlet cis powered as long as the DPR is plugged into a powered AC outlet.The AVR 7300 features a removable power cord that allows wires to be run in advance to a complexinstallation so that the unit itself need not be installeduntil it is ready for connection.When all needed connections have been made,connect the AC Power cord to the AC Power Cord Jack b.The AVR 7300 draws significantly more current thanother household devices,such as computers, that useremovable power cords.For that reason, it is importantthat only the cord supplied with the unit (or a directreplacement of identical capacity) be used.Once the power cord is connected, you are almostready to enjoy the AVR 7300’s incredible power and fidelity!20 INSTALLATION AND CONNECTIONSAVR7300(120v)-OM 4/20/04 4:12 PM Page 20](https://usermanual.wiki/Woori-Technology/AVR7300/User-Guide-417415-Page-20.png)
![22 SYSTEM CONFIGURATIONSYSTEM CONFIGURATION3. Carefully remove the protective plastic film fromthe front-panel lens.If left in place, the film willprevent proper operation of the remote control.4. Install the four supplied AAA batteries in theremote as shown. Be certain to follow the (+)and (–) polarity indicators that are in the batterycompartment.5.Turn the AVR 7300 on by pressing the Standby/On Button 1on the front panel, or via theremote by pressing the Power On Button b,the AVR Selector e∫or any of the InputSelectors3ç∂on the remote.The lighting around the Standby/On Button 1will turn blue to confirm that the unit is on.Using the On-Screen DisplayWhen making the following adjustments,you may findit easier to use the DPR 2005’s on-screen displaysystem.These easy-to-read displays give you a clearpicture of the current status of the unit and make iteasy to see which speaker, delay, input or digitalselection you are making.To the on-screen menus, make certain that you havemade a connection between either the ComponentVideo Outputs [square E] or the Video Monitor Outputs[square O] and the matching inputs on your TV,displayor projector. In order to view the menus, make certainthat the proper video input type has been selected onthe display, and that any configuration required for thedisplay, such as selection of interlace or progressivescan has been made.TO take advantage of the AVR7300’s advanced video circuitry, when a componentvideo connection is in use,make certain that the display is configured for "480P" or progressive scaninputs,if available.IMPORTANT NOTE: When viewing the on-screenmenus using a CRT-based projector, plasma display ordirect-view CRT monitor or television,it is importantthat they not be left on for an extended period of time.The constant display of a static image such as thesemenus may cause the image to be permanently“burned into” the projection tubes, plasma screen orCRT.This type of damage is not covered by the AVR7300 warranty and may not be covered by the projec-tor/TV set’s warranty.The AVR 7300 has two on-screen display modes,“Semi-OSD” and “Full-OSD.”When making configura-tion adjustments,it is recommended that the full-OSDmode be used.This will place an easily viewed list ofthe available options on the screen.Making Configuration AdjustmentsThe full-OSD system is available by pressing the OSD Button .When this button is pressed, theMASTER MENU (Figure 1) will appear, andadjustments are made from the individual menus.Figure 1The semi-OSD system is also available,allowing youto make adjustments directly, by pressing the appro-priate buttons on the front panel or remote control forthe specific parameter to be adjusted. For example, tochange the digital input for any of the sources,pressthe Digital Select Button and then press the⁄/¤Navigation Button oto scroll through thelist of options as they appear in the on-screen displayor in the Lower Display Line $.To use the full-OSD menu system, press the OSDButton .When the menu is on the screen, pressthe ⁄/¤Navigation Button ountil the on-screen➔cursor is next to the item you wish to adjust, andthen press the Set Button qto adjust that item.The menus will remain on the screen for 20 seconds,and then they will “time-out” and disappear from thescreen.The time-out may be increased to as much as 50 seconds by going to theADVANCEDSELECT menu, and changing the item titledFULL OSD TIME OUT.When the full-OSD system is in use,the menu selec-tions are not shown in the Upper or Lower DisplayLines #$.When the full-OSD menu system isused, OSD ON will appear in the Upper DisplayLine #to remind you that a video display must beused.When the semi-OSD system is used in conjunc-tion with the discrete configuration buttons,the on-screen display will show a single line of text with thecurrent menu selection.That selection will also beshown in the Upper or Lower Display Lines #$,depending on which parameter is being adjusted.Setting the System Configuration MemoryThe AVR 7300 features an advanced memory systemthat enables you to establish audio and video parametersfor each input source.This flexibility enables you tocustom-tailor the way in which you listen to eachsource and have the DPR 2005 memorize those set-tings.This means, for example,that you may set differ-ent speaker configurations with the resultant changesto the bass management system.Thanks to the use ofexclusive Harman Kardon circuitry and software alongwith DCDi by Faroudja®technology, you may also cus-tom tailor the video settings for each input source todisplay consistent, high quality video images when theAVR 7300 is used in conjunction with a digital or highdefinition display. Once these settings are made, theywill automatically be recalled whenever you select thatinput.The factory default settings for audio have all inputsexpect for DVD and Video 3 configured for their ana-log inputs.The default for DVD is Coaxial DigitalAudio Input 1 †and the default for Video 3 isOptical Digital Input 1 ®.Additionally, the defaultfor all speaker settings is “Small” with the Subwooferon. Logic 7 Music is the default surround mode for allsources,with Dolby Digital or DTS being selectedautomatically when an appropriate digital source is inuse and a digital bitstream is detected.The factory defaults for the video settings are listed inthe Appendix to this manual on page XX. Note,how-ever, that most of the video default settings are onlyapplicable when a component connection to a digitalready or HDTV monitor is in use.Both the video andaudio settings for all inputs may be changed as shownin the following pages.Before using the unit, you may want to change thesettings for some inputs so that they are properly configured to reflect the use of digital or analog inputs,the type of speakers installed and the surround modespecifics of your home theater system. Rememberthat since the DPR 2005 memorizes the settings foreach input individually, you will need to make theseadjustments for each input used. However, once theyare made,further adjustment is only required whensystem components are changed.To make this process as quick and as easy as possi-ble,we suggest that you use the full-OSD system withthe on-screen menus,and step through each input.Once you have completed the settings for the firstinput, many settings may be duplicated for the remain-ing inputs.It is also a good idea to set the configura-tion data in the order these items are listed in theMASTER MENU,as some settings require aspecific entry in a prior menu item.7 ** MASTER MENU **→IN/OUT SETUPAUDIO SETUPVIDEO SETUPMULTI-ROOMADVANCED22 SYSTEM CONFIGURATIONAVR7300(120v)-OM 4/20/04 4:13 PM Page 22](https://usermanual.wiki/Woori-Technology/AVR7300/User-Guide-417415-Page-22.png)
![CONFIGURING THE REMOTE 47CONFIGURING THE REMOTEyou must first press the Input Selectors dfor that button, and then press the Command orFunction key. Since we want to program a series of events that occur each time the Power On button is pressed, press the DPR button. In yourspecific macro,this is the first command button.Figure 447.The next display (Figure 45) and the subsequentscreens are where the actual macro programmingtakes place.The words at the left side of the topline of the display show the button that is beingprogrammed (e.g.,the Power On Button1orone of the Macro Buttons ) and the indica-tion at the right side of the top line shows thenumber of macro steps available of 20 possiblesteps.Following the instructions on the remote’sLCD screen, press the first key you wish to betransmitted in the macro.In our example, we firstwant the DPR 2005 to turn on, so the PowerButton1should be pressed.Figure 458. Once the first command button for the macro hasbeen pressed, continue to press the buttons youwish to be part of the macro,in the order they willbe used. Press each button within five seconds ofthe last button, remembering to press the InputSelector3when you are changing devicefunctions.As the buttons on the remote arepressed,the remote’s display screen will show thesteps in the macro as they are programmed(Figure 46).Figure 469. For our example, we first want the DPR Power On button pressed, followed by the TV Power On,followed by the Cable Box On, followed by theselection of the Logic 7 mode.To do that, pressthe buttons in this order:• Power On1• VID 2/TV3• Power On1• VID 3/Cable3• Power On1• DPR4• Logic 7hAs each button is pressed to enter it into themacro,you will see the button names appear andthen scroll up on the LCD display as your confir-mation of the key entry (Figure 46).10.When all commands for the macro have beenentered, press the Set Buttonqto save themacro.The display screen will show the button to which the macro has been programmed andthe number of steps used, and the word SAVEDwill blink four times in the lower line of the LCD display.When the display returns to normal, themacro has been entered and the remote is readyfor operation.11. If a macro has been programmed into the PowerOn Button1,it will play back anytime thePower On button is pressed.As the macro plays,you will see the steps appear in the remote’s LCDdisplay. Macros programmed into one of the fourdiscrete Macro buttons may be activated at anytime by pressing the appropriate button.Erasing a MacroOnce a macro has been created and stored in theDPR remote’s memory, you have the option of erasingit.You may do this at any time by following thesesteps:1. Press and hold the Program ButtonOforabout three seconds while the message shown in Figure 18 appears in the remote’s LCDInformation Display2.Release the buttonwhen the red light under the Set Buttonqappears.2.The remote’s MAIN MENU message (Figure19), will appear in the LCD display and the SetButtonqwill remain illuminated in red. Pressthe ⁄Navigation Buttonothree times sothat MACRO appears on the bottom line of theLCD screen, as shown in Figure 40. Press theSet Buttonqto enter the main macro menubranch.3.At the next menu screen (Figure 47), press the⁄/¤Navigation Button ountil the bottomline in the remote’s LCD display reads ERASE AMACRO.Press the Set Buttonqto begin theprocess of erasing a macro.Figure 474.The next display screen (Figure 48) is where youselect which macro will be erased. Press the⁄/¤Navigation Button ountil the numberof the macro you wish to erase appears.For this example we will erase the Power On macrocreated in the previous section.When the nameof the macro to be erased appears,press the Set Buttonq.Figure 485.The word ERASED will flash four times in thebottom line of the remote’s LCD display, and thenthe display will return to its normal condition.When that happens,the macro is erased and theremote is returned to normal operation.Read a MacroTo check the commands stored in the remote’s memoryfor one of the buttons,follow these steps:1. Press and hold the Program ButtonOforabout three seconds while the message shown in Figure 18 appears in the remote’s LCDInformation Display2.Release the buttonwhen the red light under the Set Buttonqappears.2.The remote’s MAIN MENU message (Figure18), will appear in the LCD display and the SetButtonqwill remain illuminated in red. Pressthe ⁄Navigation Buttonothree times sothat MACRO appears on the bottom line of theLCD screen, as shown in Figure 40. Press theSet Buttonqto enter the main macro menubranch.3.At the next menu screen (Figure 49), press the⁄/¤Navigation Button ountil the bottomline in the remote’s LCD display shows READ AMACRO.Press the Set Button qto begin theprocess of reading a macro.Figure 494.The next display screen (Figure 50) is where youselect the macro to be read. Press the ⁄/¤Navigation Button ountil the name of themacro you wish to read appears.For this example,we will read back the Power On macro created ina previous section.When the name of the macroto be read appears,press the Set Buttonq.Figure 505.As soon as the Set button is pressed, the first twosteps in the macro will be appear in the remote’sLCD screen.You may then use the ⁄/¤Navigation Button oto step up or downthrough the list of commands stored as themacro.As you read the display,you will see InputSelector Buttons3appear in brackets,(e.g.,[DPR]).When the step in the macro is a func-tion, navigation or any other button, it will appearREAD A MACROPOWER ONMACROREAD A MACROERASE A MACROPOWER ONMACROERASE A MACRO[AVR][AVR] POWER ONPOWER ON 00/20SELECT KEY PRESSSELECT A DEVICEAVRAVR7300(120v)-OM 4/20/04 4:39 PM Page 47](https://usermanual.wiki/Woori-Technology/AVR7300/User-Guide-417415-Page-47.png)
![next to the bracketed read-out of the underlyingdevice (e.g.,[AVR] POWER ON).6.When you are finished reviewing the macro’s contents,press the Set Buttonqto return the remote to normal operation.Punch-Through ConfigurationPunch-through is a capability of the remote that allows the Volume controls, Channel Up/Down buttonsor Transport keys (Play, Stop, Record, Fast Forwardand Reverse,and Skip Up/Down) to link to a differentdevice.For example,if your TV, cable box or satellitereceiver is connected through the AVR 7300, you will most likely want to use the AVR 7300’s volume con-trol commands even when the remote has been set to issue all other commands for the video device.“Punch-through” enables you to easily program theremote to do this.Volume Punch-ThroughFollow these steps to enable the Volume Up/Downand Mute controls from one device to be used whenthe remote is otherwise programmed for a differentdevice.NOTE FOR VOLUME PUNCH-THROUGH: Theremote’s default settings are for the AVR 7300’s vol-ume controls,to be used when any input or device isselected, with the exception of the VID 2/TV button.There is no need to program the remote for volumepunch-through for the AVR 7300’s controls with othersources,such as DVD.To have the AVR 7300’s vol-ume commands used when the TV device is selected,follow these steps:1. Press and hold the Program ButtonOforabout three seconds while the message shown in Figure 18 appears in the remote’s LCDInformation Display2.Release the buttonwhen the red light under the Set Buttonqappears.2.The remote’s MAIN MENU message (Figure19), will appear in the LCD display and the SetButtonqwill remain illuminated in red. Pressthe ⁄/¤Navigation Button ountilPUNCH-THROUGH appears on the bottomline of the LCD screen, as shown in Figure 51.Press the Set Buttonqto enter the mainpunch-through menu branch.Figure 513.At the next menu screen (Figure 52) press the Set Buttonqto begin programming theremote for Volume punch-through.Figure 524.The next display screen (Figure 53) is where you select the device that will receive the punch-through commands.In our example, that is the VID 2/TV button, as that is where we want theDPR 2005’s volume controls to be active.Pressthe ⁄/¤Navigation Button ountil thename of the base device appears and then pressthe Set Buttonq.Figure 535.At the next display screen (Figure 54), you willselect the device whose Volume Up/Down andMute commands will be used. Press the ⁄/¤Navigation Button ountil the desired device’sname appears to the right of the device in use. Inour example,that is the DPR 2005 (indicated byDPR).When the desired combination of devicesappears,press the Set Buttonq.Figure 546.When the Set button is pressed, the display willchange to show you that the new combination ofcontrol commands is being saved to the unit’smemory,as shown in Figure 55.The wordSAVED will flash four times and then the remotewill return to normal operation.Figure 557. Once the punch-through is programmed, the Volume Up/Down and Mute buttons of the seconddevice named will be used when those buttonsHare pressed while the master device is in use.Returning the Volume Control Settings to Default OperationIf you wish to remove the Volume punch-through sothat the commands for Volume and Mute are returnedto the factory default setting,follow the steps shownabove,except that in Steps 4 and 5, select the samedevice for both the DEVICE IN USE on the leftside of the bottom line and the PUNCH-THROUGHdevice.In the example used, the display to return theremote to default settings will appear as shown inFigure 56.Figure 56Channel Punch-ThroughChannel punch-through allows the Channel Up/Downbuttons to send commands to a different device thanthe one that has been selected for other commands.For example, you may wish to use a cable box orsatellite receiver as the source for a VCR, so youwould want the Channel Up/Down Buttons totransmit commands to the cable box even though theother button commands are programmed to operatethe VCR.To program the remote for channel punch-through,follow these steps.This example will show how to pro-gram channel punch-through so that the commandsprogrammed for Channel Up/Down for the VID 3/Cable device will be transmitted when the VID 1/VCRdevice has been selected as the current device.1. Press and hold the Program ButtonOforabout three seconds while the message shown in Figure 18 appears in the remote’s LCDInformation Display2.Release the buttonwhen the red light under the Set Buttonqappears.2.The remote’s MAIN MENU message (Figure19), will appear in the LCD display and the Set Buttonqwill remain illuminated in red.Press the ⁄/¤Navigation Button ountilPUNCH-THROUGH appears on the bottomline of the LCD screen, as shown in Figure 51.Press the Set Buttonqto enter the mainpunch-through menu branch.3.At the next menu screen, press the ⁄/¤Navigation Button ountil CHANNELappears on the bottom line of the LCD screen,as shown in Figure 57. Press the Set Buttonqto begin programming the remote for channel punch-through.Figure 574.The next display screen (Figure 58) is where youselect the device that will receive the punch-through commands.In our example, that is the VID 1/VCR button, as that is where we want thecable box’s channel controls to be active. Pressthe ⁄/¤Navigation Button ountil thename of the base device appears and then press the Set Buttonq.Figure 585.At the next display screen (Figure 59), you willselect the device whose Channel Up/Down com-mands will be used. Press the ⁄/¤NavigationDEVICE IN USEVCRPUNCH-THROUGHCHANNELPUNCH-THROUGHTV<-TVTV<-DPR [VOL] SAVEDPUNCH-THROUGHTV<-AVRDEVICE IN USETVPUNCH-THROUGHVOLUMEMAIN MENUPUNCH-THROUGH48 CONFIGURING THE REMOTECONFIGURING THE REMOTEAVR7300(120v)-OM 4/20/04 4:39 PM Page 48](https://usermanual.wiki/Woori-Technology/AVR7300/User-Guide-417415-Page-48.png)
![CONFIGURING THE REMOTE 49CONFIGURING THE REMOTEButton ountil the desired device nameappears to the right of the device in use.In ourexample,that is the cable box.When the desiredcombination of devices appears,press the SetButtonq.Figure 596.When the Set button is pressed, the display willchange to show you that the new combination of control commands is being saved to the unit’smemory,as shown in Figure 60.The wordSAVED will flash four times and then the remotewill return to normal operation.Figure 607. Once the punch-through is programmed, theChannel Up/Down Buttons of the seconddevice named will be used when those buttonsare pressed while the master device is in use.Returning the Channel Control Settings to Default OperationIf you wish to remove the Channel Punch-Through so that the commands for Channel Up/Down arereturned to the factory default setting, follow the stepsshown above,except that in Steps 4 and 5, select the same device for both the DEVICE IN USE onthe left side of the bottom line and the PUNCH-THROUGH device.In the example used, the displayto return the remote to default settings will appear asshown in Figure 61.Figure 61Transport Punch-ThroughThe Play ,Stop J,Fast Forward/ReverseI,Pause J,RecordJand Skip Up/DownKTransport Controls are set at the factory to oper-ate your DVD player, or the controls of a specificdevice such as a VCR or CD player when they areselected. However, by using the Transport Punch-Through feature you may program these controls totransmit the commands for a different device.Forexample,you may wish to operate the transport of aVCR connected to the VID 1/VCR input as the default,rather than the button for a DVD player,as shown inthe following example.1. Press and hold the Program ButtonOforabout three seconds while the message shown in Figure 18 appears in the remote’s LCDInformation Display2.Release the buttonwhen the red light under the Set Buttonqappears.2.The remote’s MAIN MENU message (Figure17), will appear in the LCD display and the SetButtonqwill remain illuminated in red. Pressthe ⁄/¤Navigation Button ountilPUNCH-THROUGH appears on the bottomline of the LCD screen, as shown in Figure 51.Press the Set Buttonqto enter the mainpunch-through menu branch.3.At the next menu screen, press the ⁄/¤Navigation Button ountil TRANSPORTappears on the bottom line of the LCD screen, asshown in Figure 62. Press the Set Buttonqto begin programming the remote for transportpunch-through.Figure 624.The next display screen (Figure 63) is where youselect the device that will receive the punch-through commands.In our example, that is the TV button, as that is where we want the VCR’stransport controls to be active.Press the ⁄/¤Navigation Button ountil the name of thebase device appears and then press the SetButtonq.Figure 635.At the next display screen (Figure 64), you willselect the device whose transport commands willbe used. Press the ⁄/¤Navigation Buttonountil the desired device name appears to theright of the device in use.In our example, that isthe VCR.When the desired combination ofdevices appears,press the Set Buttonq.Figure 646.When the Set button is pressed, the display willchange to show you that the new combination ofcontrol commands is being saved to the unit’smemory,as shown in Figure 65.The wordSAVED will flash four times and then the remotewill return to normal operation.Figure 657. Once the punch-through is programmed, the transport buttons of the second device named will be used when those buttons are pressedwhile the master device is in use.Returning the Transport Control Settings toDefault OperationIf you wish to remove the Transport Punch-Through sothat the transport commands are returned to the fac-tory default setting,follow the steps shown above,except that in Steps 4 and 5, select the same devicefor both the DEVICE IN USE on the left side of thebottom line and the PUNCH-THROUGH device. Inthe example used, the display to return the remote todefault settings will appear as shown in Figure 66.Figure 66EzSet ConfigurationHarman Kardon’s patented EzSet feature makes it easierthan ever to calibrate the output levels on your newreceiver for maximum playback accuracy. In additionto automatically setting the levels,the DPR remote’sLCD display allows the unit to be used as a directread-out SPL meter. Complete instructions for usingthe EzSet features of the DPR remote are found onpages 27 – 29 of this owner’s manual.In most cases you will find it easier to access theEzSet capabilities directly by pressing the SPL SelectButton and following the menu prompts asdetailed on pages 27 and 28. However, there is onefunction of the remote that is only available throughthe remote’s menu system being described in thissection.To avoid having the calibration settings created withEzSet changed accidentally, the remote allows you todisable the SPL Select Button on the remote.To de-activate the button, follow these steps:1. Press and hold the Program ButtonOforabout three seconds while the message shown in Figure 18 appears in the remote’s LCDInformation Display2.Release the buttonwhen the red light under the Set Buttonqappears.2.The remote’s MAIN MENU message (Figure 19),will appear in the LCD display and the Set Buttonqwill remain illuminated in red. Press the⁄/¤Navigation Button ountil SET SPKRLEVELS appears on the bottom line of the LCDscreen, as shown in Figure 67. Press the SetButtonqto enter the main EzSet menubranch.Figure 67MAIN MENUSET SPKR LEVELSPUNCH-THROUGHTV<-TVTV<-VCR [TRS] SAVEDPUNCH-THROUGHTV<-VCRDEVICE IN USETVPUNCH-THROUGHTRANSPORTPUNCH-THROUGHVCR<-VCRVCR<-CBL [CHAN] SAVEDPUNCH-THROUGHVCR<-CBLAVR7300(120v)-OM 4/20/04 4:39 PM Page 49](https://usermanual.wiki/Woori-Technology/AVR7300/User-Guide-417415-Page-49.png)
![3.At the next menu screen (Figure 68) press the⁄/¤Navigation Buttons oonce so thatEZSET DISABLE appears in the lower line ofthe LCD display.Figure 684.Within five seconds,press the Set Buttonqtodisable the SPL Select Button .Once theSet Buttonqis pressed the word EXITINGwill flash four times in the lower line of the LCDdisplay and then it will return to normal operation.Once these steps are completed, when the SPLSelect Button is pressed the remote will show EZSET DISABLE and it will not be activated.To restore the EzSet feature to normal operation,repeat the procedure outlined above,except that inStep 3 you should press the ⁄/¤NavigationButton oso that EZSET ENABLE appears in thelower line of the LCD display.When that displayappears,press the Set Buttonqand the EzSetfeature will be reactivated.You may then press theClear Button9to exit the remote’s menu systemand return to normal operation or press the SetButtonqagain to immediately use the EzSet feature to calibrate the system as shown on pages 27 and 28.RenamingWhile the names given to the buttons and inputs onthe remote represent recognizable categories ofaudio/video products,system operation may be easierif the displays shown in the remote’s LCD screen arecustomized to reflect the specific characteristics of aplayback source’s brand name or the new functiongiven to a specific button when one remote’s controlsare programmed into the DPR remote.The DPRremote allows you to change the name of either amaster device or any button on the remote using thefollowing steps.Renaming a DeviceTo rename a specific device/input source button, fol-low these steps.For this example,we will show youhow to rename the Device/Input Selector normallyshown as “TV” to “HDTV TUNER.”1. Press and hold the Program ButtonOforabout three seconds while the message shown in Figure 16 appears in the remote’s LCDInformation Display2.Release the buttonwhen the red light under the Set Buttonqappears.2.The remote’s MAIN MENU message (Figure 17),will appear in the LCD display and the Set Buttonqwill remain illuminated in red. Press the⁄/¤Navigation Button ountil RENAMEappears on the bottom line of the LCD screen, asshown in Figure 69.Figure 693.At the next menu screen press the ⁄/¤Navigation Button ountil RENAMEDEVICE appears on the bottom line of the LCD screen, as shown in Figure 70. Press the Set Buttonqto begin renaming a device.Figure 704.The next display screen (Figure 71) is where youselect the device that will be renamed. In ourexample,that is the TV button.Press the ⁄/¤Navigation Button ountil the name of thebase device appears and then press the SetButtonq.Figure 715.At the next menu screen you will see the devicename on the bottom line of the display with ablinking cursor box to the right of the devicename.Press the ‹Navigation Button otoreturn the blinking cursor to the far left side of thedisplay line.You may then retitle the device nameas shown in the next step.6.To enter the new name,press the Numeric KeysA.The letters above the numbered buttonsindicate which letter or symbol will appear whenthe button is pressed during the renamingprocess.The first press of the button will enter thefirst letter shown, subsequent presses of the samebutton will change the display to the other lettersabove that numbered key. For example,since thefirst letter we need to rename the input to HDTVTuner is an “H”, you would locate the “H” abovethe “4” button, and press the button twice.Thefirst press shows a “G,” the second press changesit to an “H.” Consult the table at the end of thissection to see which characters pressing a partic-ular button generates.7.After you enter the first letter of the new devicename,there are three options for entering the nextcharacter:a.To enter a letter that requires a different numeric key to be pressed, simply press thatbutton.The cursor will automatically move to the next position and the first letter accessed by the new button will appear. Following ourexample,the next letter needed is a “D,” so you would press the “3” button once.b. To enter a letter that uses the same numerickey, you must first press the ›NavigationButtonoto move the blinking cursor blockto the next position.Then press the NumericKeyAas required to enter the desired letter.c.To enter a blank space, press the ›NavigationButtonotwice.The first press will move thecursor to the right, and the second press willmove the cursor one more space to the right,leaving a blank space between the last letterand the next one.8. Repeat Step 7 as needed to enter all the neededletters,numbers, characters and spaces.9.When the text entry is complete, press the Set Buttonq.The LCD display will blinkDEVICE RENAMED three times and thenreturn to normal operation.Once a device is renamed you will see the new nameon the top line of the remote’s LCD display wheneverthe Input//Device Selector3is pressed, or whenany other command/function button on the remote ispressed after the main Device Selector is pressed.Note that renaming a device in the remote will notchange the name of the input used by the on-screenmenu system of the AVR 7300.NOTES ON RENAMING DEVICES:• To move the cursor to the right or left of the displayduring the renaming process,press the ‹/›Navigation Buttonsoas required.• The table below shows the letters,numbers andcharacters that may be accessed by pressing theNumeric Keys:Key Characters Key Characters1[,],/,1 6 M,N,O,62 A,B,C,2 7 P,Q,R,S,73D,E,F,3 8 T,U,V,84G,H,I,4 9 W,X,Y,Z,95J,K,L,5 0 -,.,#,0• Renaming a device changes the name of the deviceonly, not any of the individual key functions withinthat device memory.To change the name of an individual device,follow the instructions in the nextsection.RENAME DEVICETVRENAMERENAME DEVICEMAIN MENURENAMESET SPKR LEVELSEZSET DISABLE50 CONFIGURING THE REMOTECONFIGURING THE REMOTEAVR7300(120v)-OM 4/20/04 4:39 PM Page 50](https://usermanual.wiki/Woori-Technology/AVR7300/User-Guide-417415-Page-50.png)
