Wistron NeWeb SWA9 Wireless Audio Module User Manual

Wistron NeWeb Corporation Wireless Audio Module

User Manual

AVNERA CORPORATION  |  16505 NW BETHANY COURT SUITE 100  |  BEAVERTON, OREGON 97006, U.S.A.  |  MAIN +1.503.718.4100  |  FAX +1.503.718.4101  |  WWW.AVNERA.COM  AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA    General Description Every consumer wants to be free from wires, but it has been challenging to find a low-cost, high-quality, easy-to-use wireless audio solution for the wireless subwoofer market. Avnera’s proprietary wireless system takes a new approach to wireless audio. The wireless protocol was designed from the ground up and delivers uncompressed mono audio, with fixed latency over the air, without interference problems. Avnera’s wireless modules offer a low-touch, easy-to-integrate wireless audio solution and enable fast time to market by already solving the problem associated with FCC certification, antenna tuning and board optimization. Modules based on Avnera’s AV6600 silicon provide breakthrough wireless audio functionality with fixed low-latency point-to-point transport of uncompressed mono PCM audio data at 16-bit, 48 kHz resolution using either analog or digital (I2S) interfaces.   Applications   Wireless Subwoofers   Mono audio channel transmission    Ordering Options  AVMD6600-SWA91TXD: Transmit module with digital audio input and integrated printed PCB antennas AVMD6600-SWA91RXD: Receive module with digital audio output and integrated printed PCB antennas AVMD6600-SWA91RXA: Receive module with analog audio output and integrated printed PCB antennas  Features  Audio Interfaces   I2S Digital Input Interface with 95dB end-to-end digital audio path  Integrated DAC supporting Analog output with 90dB SNR and 20-20KHz bandwidth (RXA model only)   Support for 15m range    Frequency range: 2.4 GHz ISM band, continuous dynamic frequency selection   Forward error correction coding, error detection, and audio-specific error concealment   Dual onboard printed PCB antennas for multipath and fading mitigation   Auto-search/synch and dynamic channel selection   Low, fixed latency of 13ms, suitable for video lip-synch   Connector: 2mm header which allows for either horizontal or vertical module mounting    Sample rate converter: Support for 16, 20, 24, and 32 bit PCM words at 8,16, 22.05, 24, 32, 44.1, and 48 kHz   General purpose over-the-air (OTA) serial interface:    2 kbps, bi-directional, full duplex   Support for meta-data and remote control commands  PRELIMINARY AudioMagic™ Module Datasheet Point-to-point AVMD6600-SWA91 module family for Mono Wireless Audio Systems, based on Avnera’s AV6600 IC
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  2  AVNERA PROPRIETARY & CONFIDENTIAL 1 Table of Contents General Description ______________________________________________________________ 1 Applications ____________________________________________________________________ 1 Ordering Options ________________________________________________________________ 1 Features _______________________________________________________________________ 1 1 Table of Contents ____________________________________________________________ 2 2 Lists of Figures and Tables ____________________________________________________ 3 3 AVMD6600-SWA91-TXD/RXD/RXA Functional Block Diagrams _____________________ 4 4 AVMD6600-SWA91 Pin Information ____________________________________________ 7 5 AVMD6600-SWA91 Mechanical Dimensions______________________________________ 9 6 Electrical Specifications ______________________________________________________ 10 6.1 Absolute Maximum Ratings ______________________________________________________________ 10 6.2 Recommended Operating Range __________________________________________________________ 10 6.3 Electrical Characteristics ________________________________________________________________ 11 7 Application information ______________________________________________________ 12 7.1 Mechanical requirements ________________________________________________________________ 12 7.2 Application circuit ______________________________________________________________________ 13 7.3 External I2S Requirement  _______________________________________________________________ 13 8 FCC and Industry Canada certification information _______________________________ 14 8.1 Label Information ______________________________________________________________________ 14 8.2 Equipment labeling requirements _________________________________________________________ 14 8.3 User manual labeling requirements ________________________________________________________ 15 9 Ordering Information  _______________________________________________________ 16 10 Contact Information and Legal Disclaimer _____________________________________ 17
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  3  AVNERA PROPRIETARY & CONFIDENTIAL 2  Lists of Figures and Tables Table 1: AVMD6600-SWA91 Module Block Diagram Description ___________________________________________ 6 Table 2: AVMD6600-SWA91 Pin Information ___________________________________________________________ 7 Table 3; AVMD6600-SWA91 Electrical Characteristics __________________________________________________ 11 Table 4: AVMD6600-SWA91 Module Ordering Information _______________________________________________ 16  Figure 1: AVMD6600-SWA91TXD Module Block Diagram................................................................................................ 4 Figure 2: AVMD6600-SWA91RXD Module Block Diagram ............................................................................................... 4 Figure 3: AVMD6600-SWA91RXA Module Block Diagram ................................................................................................ 5 Figure 4: AVMD6600-SWA91 mechanical dimensions ....................................................................................................... 9
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  4  AVNERA PROPRIETARY & CONFIDENTIAL 3 AVMD6600-SWA91-TXD/RXD/RXA Functional Block Diagrams The AVMD6600-SWA91 module is available in three variations, Digital Input Transmitter, Digital Output Receiver and Analog Output Receiver.  Note:  The device does not have full I2S master capability and cannot generate MCLK as an output.   AV6600AntennaDiversitySwitch BalunDSCRFPRFNCrystalTWIEEPROMSPISPI(Slave) I2SGPIOGPIO VBATTV3.3LEDLEDI2S Audio Input2.4-2.5GHz Printed PCB AntennasAntenna matching networksRESET_N RESET_N Figure 1: AVMD6600-SWA91TXD Module Block Diagram    AV6600AntennaDiversitySwitch BalunDSCRFPRFNCrystalTWIEEPROMSPISPI(Slave) I2SGPIOGPIO VBATTV3.3LEDLEDI2S Audio Output2.4-2.5GHz Printed PCB AntennasAntenna matching networksRESET_N RESET_N Figure 2: AVMD6600-SWA91RXD Module Block Diagram
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  5  AVNERA PROPRIETARY & CONFIDENTIAL   Figure 3: AVMD6600-SWA91RXA Module Block Diagram
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  6  AVNERA PROPRIETARY & CONFIDENTIAL Table 1: AVMD6600-SWA91 Module Block Diagram Description  Interface Description SPI  The AVMD6600s SPI interface is used to allow an external host to control the AV6600 IC and to facilitate testing of the module.   GPIO/ LED  The GPIO and LED lines allow buttons and LEDs to be connected to the AVMD6600-SWA91 to allow the user to control the Audio Magic system and communicate the system’s state to the user. Analog Audio  These pins form the AVMD6600-SWA91RXA module’s analog audio output.  The analog ground on the module and should be isolated from the host system’s ground to prevent the creation of noise-inducing ground loops. RESET_N  This pin connects directly to the “RESET_N” pin on the AV6600 IC and is used to signal the module to power on and off. V3.3  This pin provides power to all elements of the AVMD6600-SWA91.  Internal regulators condition the input power according to the requirements of the various sub-circuit blocks. I2S These input pins connect to the AV6600’s digital audio interface and provide a digital audio input channel. The AVMD6600-SWA91 TXD is always an I2S slave while the AVMD6600-SWA91 RXD can be either a Slave or a Master I2S port but the module cannot generate MCLK as an output..  Depending upon module configuration the audio data direction will change.
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  7  AVNERA PROPRIETARY & CONFIDENTIAL 4  AVMD6600-SWA91 Pin Information Table 2: AVMD6600-SWA91 Pin Information Pin Number  Pin Name  TXD/RXD Module  Pin Name RXA Module  Type Pin Description 1  Not Connected  Not Connected  Analog Ground  Audio section ground; must be connected to LINE_IN_COM at the audio source to minimize noise.  2  Not Connected  Not Connected  Analog Ground  Audio section ground. Both LINE_IN_COM and LINE_IN_COM2 must be isolated from system ground for best noise performance 3  Not Connected  Not Connected  Analog Input  Reserved, not supported on these module configurations 4 Not Connected  LINE_OUT  Analog Output  Mono Analog Audio Output 5 Not Connected  LINE_OUT_COM Analog Ground  Audio section ground. LINE_OUT_COM must be isolated from the system ground for best noise performance. 6  GND  GND  Ground  Digital section ground. Tie to Pin 24 as close to the module as possible  7  V3.3  V3.3  Power  Main power supply (3.3 Volts) 8  ADAT/GPIO1  GPIO1  Digital I/O  Multifunction; I2S digital Audio data output (Input for TXD, Output for RXD), General Purpose I/O Default = ADAT digital module 9  LRCLK/GPIO2  GPIO2  Digital I/O  Multifunction; I2S digital Audio frame clock input (Slave for TXD, Master/Slave for RXD ), General Purpose I/O Default = LRCLK digital module 10  BCLK/GPIO3  GPIO3  Digital I/O  Multifunction; I2S digital Audio bit clock input (Slave for TXD, Master/Slave for RXD), General Purpose I/O Default = BCLK digital module 11 LED  LED  Analog Output  LED drive line; current sink to GND 12 RESET_N RESET_N Digital Input  Active-LOW Reset input expecting open drain connection 13 CMP CMP Analog Input  Comparator input; default function is sensing battery status 14 S_MOSI/S_CLK/ GPIO12  S_MOSI/S_CLK/ GPIO12  Digital I/O  Multifunction, SPI slave serial data input, I2C slave clock, General-Purpose I/O Default = S_MOSI 15 S_MISO/S_SDA/ GPIO13  S_MISO/S_SDA/ GPIO13  Digital I/O  Multifunction, SPI slave serial data output, I2C slave data, General-Purpose I/O Default = S_MISO 16  S_SCLK/GPIO14  S_SCLK/GPIO14  Digital I/O  Multifunction, SPI slave clock, General-Purpose I/O Default = S_SCLK
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  8  AVNERA PROPRIETARY & CONFIDENTIAL 17  S_SSB/GPIO15  S_SSB/GPIO15  Digital I/O  Multifunction, SPI slave select, General-Purpose I/O Default = S_SSB 18  UART_RX/GPIO6  UART_RX/GPIO6  Digital I/O  Multifunction, UART receive, General-Purpose I/O Default = GPIO6 19  UART_TX/GPIO7 UART_TX/GPIO7 Digital I/O Multifunction, UART transmit, General-Purpose I/O Default = GPIO7 20 M_MOSI/M_SCL/ GPIO4  M_MOSI/M_SCL/ GPIO4  Digital I/O  Multifunction, SPI master serial data output, I2C master clock, General-Purpose I/O Default = M_SCL 21 M_MISO/M_SDA/ GPIO6  M_MISO/M_SDA/ GPIO6  Digital I/O  Multifunction, SPI master serial data input, I2C master data, General-Purpose I/O Default = M_SDA 22  M_SCLK/GPIO8  M_SCLK/GPIO8  Digital I/O  Multifunction, SPI master serial clock, General-Purpose I/O Default = GPIO8 23  M_SSB/GPIO9  M_SSB/GPIO9  Digital I/O  Multifunction, SPI master serial select, General-Purpose I/O Default = GPIO9 24  GND  GND  Ground  Digital section ground. Tie to Pin 6 as close to the module as possible
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  9  AVNERA PROPRIETARY & CONFIDENTIAL 5  AVMD6600-SWA91 Mechanical Dimensions  Figure 4: AVMD6600-SWA91 mechanical dimensions
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  10  AVNERA PROPRIETARY & CONFIDENTIAL  6  Electrical Specifications  6.1  Absolute Maximum Ratings Absolute Maximum Ratings (AMR) are stress ratings only. AMR corresponds to the maximum value that can be applied without leading to instantaneous or very short-term unrecoverable hard failure (destructive breakdown). Stresses beyond those listed under AMR may cause permanent damage to the device. Functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Range” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may adversely affect device reliability. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified.   CONDITION MIN MAX V3.3 Supply Voltage Input  -0.3V  3.6V Input Voltage Range – Digital Inputs1 -0.3V 3.6V Input Voltage Range – Analog Inputs  -0.3V V3.3+0.3V Operating Temperature  0ºC  +70ºC Storage Temperature  -40ºC  +100ºC Assembly Temperature    TBD Static Discharge Voltage – HBM2   TBD Static Discharge Voltage – MM3   TBD  Notes: Note 1:  Digital GPIO Pins are 5V Tolerant when programmed as Inputs. Note 2:  Terminology: HBM => ESD human body model Note 3:  Terminology: MM => Machine model  6.2 Recommended Operating Range PARAMETER MIN TYP MAX UNIT V3.3 Supply pin voltage   3.0    3.6  V Ambient Temperature (TA) 0  70 ºC
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  11  AVNERA PROPRIETARY & CONFIDENTIAL  6.3 Electrical Characteristics  Test Conditions: TA=+25ºC, V3.3=3.3V  Table 3; AVMD6600-SWA91 Electrical Characteristics PARAMETER CONDITIONS MIN TYP MAX UNIT RF Frequency Range    2405   2477  MHz Audio Output Voltage1     2 Vpk-pk Audio SNR Analog Output1    88   dB  Audio SNR I2S Input/Output2  I2S end to end     94    dB Analog Audio THD+N3     tbd   dB Range (LOS)       15  m Current consumption  V3.3(Active Audio mode)    50    mA Note 1:  AVMD6600-SWA91RXA module only   Note 2:  AVMD6600-SWA91TXD/RXD modules only    Note 3:  Measured at -3dbFS input, A weighting. Output is taken, using external DAC on Avnera development board.
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  12  AVNERA PROPRIETARY & CONFIDENTIAL 7 Application information 7.1 Mechanical requirements Figure 5: Recommended module antenna system clearance
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  13  AVNERA PROPRIETARY & CONFIDENTIAL   7.2 Application circuit Schematics are provided separately.   7.3 External I2S Requirement The AVMD6600-SWA91 TXD module is an I2S slave only device and requires connection to a master I2S device to provide LRCLK and BCLK. The AVMD6600-SWA91 RXD module is normally an I2S slave and generates LRCLK, BCLK as well as I2S data out. The AVMD6600-SWA91 RXD module can be configured as an I2S master but is not capable of generating MCLK as an output so can only be used with external slave devices that contain some form of rate converter.
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  14  AVNERA PROPRIETARY & CONFIDENTIAL 8  FCC and Industry Canada certification information 8.1 Label Information The AVMD6600-SWA91 family of modules will be certified by the requirements set by the US Federal Communications Commission (Part 15) and Industry Canada (RSS-Gen, Issue 3, 2010-12 and RSS-210 issue 8, 2010-12) for certification as modular intentional radiators. The certification identification numbers are as follows:  US FCC ID: NKR-SWA9 Industry Canada (IC): 4441A-SWA9  * IDs will be provided after certification has been completed  Avnera makes the following representations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)  This device may not cause harmful interference,  (2)  This device must accept any interference received, including interference that may cause undesired operation. Per FCC regulation 47 CFR 15.21: Changes or modifications not expressly approved by Avnera, as the party responsible for compliance, can void the user’s authority to operate the equipment using AVMD6600-SWA91 modules. 8.2  Equipment labeling requirements  The statement shown below, or its equivalent, must appear on the external label of every piece of equipment that contains an AVMD6600 module. If the size of the final equipment is too small to support such a label, the statement described in must appear in the user manual for that equipment.   Contains  FCC ID NKR-SWA9 IC: 4441A-SWA9  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  15  AVNERA PROPRIETARY & CONFIDENTIAL 8.3  User manual labeling requirements  The statements shown below, or their equivalents, must appear in the user manual for equipment containing AVMD6600-SWA91 modules:    Contains  FCC ID NKR-SWA9 IC: 4441A-SWA9  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) this device must accept any interference received, including interference that may cause undesired operation  Per FCC regulation 47 CFR 15.21: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  16  AVNERA PROPRIETARY & CONFIDENTIAL 9 Ordering Information Table 4: AVMD6600-SWA91 Module Ordering Information Module Part Number  Option Code  Description SWA91TXD  -TXD  Digital Input , 2mm Header, integrated printed PCB antennas SWA91RXD  -RXD  Digital Output, 2mm Header, integrated printed PCB antennas SWA91RXA  -RXA  Analog Output, 2mm Header, integrated printed PCB antennas
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  17  AVNERA PROPRIETARY & CONFIDENTIAL 10 Contact Information and Legal Disclaimer  Avnera Corporation 16505 Bethany Court, Suite 100 Beaverton, Oregon 97006 U.S.A. Main: +1.503.718.4100 Fax: +1.503.718.4101 www.avnera.com  Avnera Corporation reserves the right to make changes without notice to the product to improve function, reliability, or performance. Avnera Corporation does not assume any liability arising from the application or use of the products or circuits described herein.
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  18  AVNERA PROPRIETARY & CONFIDENTIAL FCC Statement Federal Communication Commission Interference Statement  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ●  Reorient or relocate the receiving antenna. ●  Increase the separation between the equipment and receiver. ●  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ●  Consult the dealer or an experienced radio/TV technician for help.  FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.  Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.  USERS MANUAL OF THE END PRODUCT: The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.  LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: NKR-SWA9 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label:  This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
AudioMagic AVMD6600-SWA91 Family Module Datasheet  PRELIMINARY v0p1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE  19  AVNERA PROPRIETARY & CONFIDENTIAL IC Statement  This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B conforme á la norme NMB-003 du Canada.   This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.   This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.   IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module.  Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.   USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IC statement is required to be available in the users manual: This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.    LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX IC : 4441A-SWA9 ".

Navigation menu