Wistron NeWeb DFCN4 NFC Module User Manual WG3004A U5 Product Specification

Wistron NeWeb Corporation NFC Module WG3004A U5 Product Specification

USERS MANUAL

DFCN-4 User manual (V0.3) Model Name: DFCN-4 NFC MODULE Description: NFC reader/writter module compatible Edition # Reason for revision Issue date V0.1 Initial Document 2013/12/17 V0.2 For regular document applied 2014/1/2 V0.3 Adding ICES-003 warning 2014/1/27 This document contains proprietary information which is the property of Wistron NeWeb Corporation and is strictly confidential and shall not be disclosed to others in whole or in part, reproduced, copied, or used as basic for design, manufacturing or sale of apparatus without the written permission of Wistron NeWeb Corporation.
NFC module Delivery Specification V0.3 1 I. Introduction DFCN-4 is a kind of NFC (Near Field Communication) module that could be embedded in one IT system by simply connecting the module through I2C interface and start developing his application software. II. DESIGN REFERENCE DFCN-4 build a contactless front-end towards contactless applications available on existing system. Integrated MCU is decoupling the host controller from the timing constrains of RF communication and allowing autonomous operation, it provides flexible and integrated power management unit for RF front-end. DFCN-4 reference design module consists of the following: • Reference Design: When the user wishes to incorporate the DFCN-4 to their device, it is strongly recommended that this reference design is copied “as is” in the final application board to guarantee optimum performance, regulatory compliance and lowest development time and design effort. • MCU FPC/FFC Connector: Allow user to connect the DFCN-4 module to the host board via FPC/FFC connector. • Antenna Connector: Connected to FPC antenna, please note that matching circuitry should designed on antenna.
NFC module Delivery Specification V0.3 2 III. Hardware Block Diagram DFCN-4 is a full feature NFC module and compliant with NFC standards (NFC Forum, EMVCo, ETSI/SCP). DFCN-4 has an optimized architecture for low-power consumption in different operation modes. The RF contactless front-end is supporting various transmission modes according to NFCIP-1, NFCIP-2, ISO/IEC14443, ISO/IEC 15693, ISO-14443, MIFARE, and FeliCa specifications. The major internal components are illustrated in Figure 1-1. Figure 1-1 NFC module Major Component and System Interface
NFC module Delivery Specification V0.3 3 IV. Pin Definition Host connector Antenna connector Pin number Name Configuration Description 1 MOD_VDD Power 3.3V power supply 2 MOD_GND Ground Module ground 3 SWP SWP data SWP data line to UICC/SIM 4 VCC_BOOST Power supply Power rail for Booster 5 IRQ Output Interrupt to host 6 PMUVCC Power supply Power supply to UICC/SIM 7 I2C_SDA Input/ Output I2C data line 8 I2C_SCL Input I2C clock 9 MOD_GND Ground Module ground 10 Reset/Wakeup Input Wake up the module from standby mode or reset the module 11 DWL_REQ Input Firmware download control 12 SIMVCC Power The power rail used to power UICC/SIM. 13 MOD_VDD Power 3.3V power supply 14 VDD_IO Power 3.3V for host IO reference voltage 15 MOD_GND Ground Module ground Pin number Name Configuration Description 1 ANT1 Power Antenna connection for Card emulation 2 RXP Input Contactless receiver input 3 TX1 Contactless receiver output 1 4 GND Ground Transmitter ground 5 TX2 Contactless receiver output 2 6 RXN Input Contactless receiver input 7 ANT2 Power Antenna connection for Card emulation
NFC module Delivery Specification V0.3 4 V. Specification/Feature Item Standard specifications Main chipset  NXP NPC100 Frequency  13.56MHz NFC Standards  ISO/IEC 14443A, ISO/IEC 14443B PCD  FeliCa PCD mode  Mifare PCD encryption mechanism  ISO/IEC 15693/ICODE VCD mode  NFC Forum tags  NFCIP-1/NFCIP-2 protocol  EMVCo 2.0.1 for PICC and PCD mode  NFC Forum Wave 1 and Wave 2  ETSI/SCP 102 613 and 102 622 for SWP/HCI Host interface  NCI protocol interface according to NFC Forum NCI 1.0 standardization  I2C High-speed mode supported Host connector  15 pin FPC/FFC Antenna connector  7 pin FPC/FFC Operation temperature  0o ~ 85o C Storage temperature  -20o ~ 125o C VI. Electrical Characteristics Symbol Parameter Min Typical Maximum Unit MOD_VDD Power supply input 2.7 3.3 5.5 V VDD_IO IO power supply 3.0 3.3 3.6 VCC_BOOST Power supply input - 5.0 5.5 VDD_SIM Power supply for SWP interface 1.62 3.6 Note. Test without operating booster
NFC module Delivery Specification V0.3 5 VII. Recommended Operation Conditions Supply voltage  AC mains  DC Type of DC Source  Internal DC supply  External DC adapter  Battery Operational Climatic  Tnom (20°C)  Tmax (85°C)  Tnim (-25°C) VIII. Power sequence i. Power up Symbol Parameter Min Typical Maximum Unit TVBATVEN Minimum time from VBAT high to VEN high 0 - - ms TPVDDVEN Minimum time from PVDD high to VEN high 0 - - ms ii. Reset Symbol Parameter Min Typical Maximum Unit TRESETVEN VEN pulse width to rest 3 - - us TBOOT Boot time - - 2.5 ms iii. Down load mode Symbol Parameter Min Typical Maximum Unit TGPIO4VEN DWL_REQ voltage high to VEN high 0 - - ms
NFC module Delivery Specification V0.3 6 IX. Assembly Guidelines X. Mechanical Dimension NKR-DFCN4
NFC module Delivery Specification V0.3 7 XI. FPC/FFC specifications i. AFC45-S15H1A-HF : 15 pin FFC ii. AFC26-S07F1A-HF : 7 pin FFC
NFC module Delivery Specification V0.3 8 XII. Certifications and Regulatory Item Feature Description 6.1 FCC RF: FCC part 15C EMI: FCC part 15B FCC grant: TCB Filing fee 6.2 CE RF: EN302291 Class B EMC: EN301489-1/-3 Safety: EN 60950-1:2006/A11:2009 6.3 IC RSS-210 ISSUE 8 RSS-GEN ISSUUE 3 General: This modular approval is limited to OEM/Integrators installation only. OEM integrators are responsible for ensuring that the end-user has no manual instructions to remove or install module. End Product Labeling (FCC) When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text: “Contains FCC ID: __ NKR-DFCN4__ The grantee's FCC ID can be used only when all FCC compliance requirements are met. Required FCC Compliance Statement for Host Integration To integrate this module into the host, the host manufacturer is responsible for the applicable FCC rules, including the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. In the user manual of the host device, the following statements are required to be included.  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful
NFC module Delivery Specification V0.3 9 interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.  Changes or modifications not expressly approved by the party responsible for compliance could void the user„s authority to operate the equipment. FCC Module Integration Restriction: This module has been certified by FCC as single module approval with the following restrictions: 1. The Loop antenna was verified in the conformity testing, and for compliance the antenna shall not be modified. A separate approval is required for all other operating configurations, including different antenna configurations. 2. If any other simultaneous transmission radio is installed in the host platform together with this module, or above restrictions cannot be kept, a separate RF exposure assessment and FCC equipment authorization is required. End Product Labeling (IC) Labeling Requirements for the Host Device (from Section 3.2.1, RSS-Gen, Issue 3, December 2010): The host device shall be properly labeled to identify the module within the host device. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the Industry Canada certification number of the module, preceded by the words ―Contains transmitter module, or the word ―Contains, or similar wording expressing the same meaning, as follows: "Contains transmitter module IC:_ 4441A-DFCN4_. Required IC Compliance Statement for Host Integration To integrate this module into the host, the host manufacturer is responsible for the applicable Industry Canada rules, including the limits for a Class B digital device, pursuant to ICES-003 of the Industry Canada Rules In the user manual of the host device, the following statements are required to be included.  This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and
NFC module Delivery Specification V0.3 10 (2) this device must accept any interference, including interference that may cause undesired operation of the device.  This Class B digital apparatus complies with Canadian 4441A-DFCN4.  Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement."  Cet appareil numérique de la classe B est conforme à la norme 4441A-DFCN4 du Canada. IC Module Integration Restriction: This module has been certified by Industry Canada as modular approval with the following restrictions: 1. The Loop antenna was verified in the conformity testing, and for compliance the antenna shall not be modified. A separate approval is required for all other operating configurations, including different antenna configurations. 2. If any other simultaneous transmission radio is installed in the host platform together with this module, or above restrictions cannot be kept, a separate RF exposure assessment and IC equipment certification is required. Warning According to “Administrative Regulations on Low Power Radio Waves Radiated Devices” Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low power radio-frequency devices. The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operation immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act. The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices” CAN ICES-3(B)/ NMB-3(B)
NFC module Delivery Specification V0.3 11 According to “Administrative Regulations on Low Power Radio Waves Radiated Devices” Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low power radio-frequency devices. The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operation immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act. The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices”

Navigation menu