Wilson Electronics 819D Dual Band Bidirectional Amplifier User Manual 1

Wilson Electronics, LLC Dual Band Bidirectional Amplifier Users Manual 1

Contents

Users Manual 1

Installation GuideWilson Electronics, Inc.3301 E. Deseret Drive, St. George, Utah 84790For additional technical support go towww.wilsonelectronics.comPhone: 1-866-294-1660 Fax: 1-435-656-2432DIRECT CONNECTIONVehicle & BuildingThe term “IC:” before the radio certification number only signifiesthat Industry of Canada technical specifications were met.AMPSDIRECTCONNECTIONAMPLIFIERPart# 811101FCC ID: PWO824DIC: 4726A-824DiDENDIRECTCONNECTIONAMPLIFIERPart# 814001FCC ID: PWO806DIC: 4726A-806DDUAL BANDDIRECTCONNECTIONAMPLIFIERPart# 811201FCC ID: PWO819DIC: 4726A-819D
231. PURPOSE OF THE DIRECT CONNECTION AMPLIFIERThe Direct Connection Bi-directional Amplifier improves RF coverage in areas with no signal or low signal strength. Part# 811101 Amplifies the signal on 800MHz up to 3 watts and allows for the full benefit of the outside antenna on 1900MHz frequencies. Part# 814001 Amplifies the iDEN (Nextel) frequencies up to 3 watts.2. PACKAGE CONTENTS 2.1 Bi-directional Direct Connection Amplifier. 2.2 DC plug-in power supply with ON/OFF switch. 2.3 6ft. Adapter Extension Cable.3. HOW THE DIRECT CONNECTION AMPLIFIER FUNCTIONSWhen using 800 MHz the signal is received by the outside antenna from the cell site. The signal is then AMPLIFIED and sent into your phone through the adapter (sold separately). When the phone transmits, the signal is sent to the amplifier through the adapter then AMPLIFIED and transmitted to the cell site through the outside antenna. When using 1900MHz (PCS) the signal bypasses the amplifier’s circuitry while getting full benefit from the outside antenna.NOTE: Amplifier #814001 does not have a 1900MHz (PCS) bypass as iDEN (Nextel) does not utilize this frequency.Package ContentsAMPLIFIERDC PLUG-INPOWER SUPPLY6FT ADAPTEREXTENSION CABLE
234. AMPLIFIER INSTALLATION (see illustration on pg.4)4.1 Installing the Wilson Cellular Antenna4.1.1 See antenna packaging for model specific instructions.WARNING: Verify that both the outside antenna and adapter extension cable are con-nected before powering up the AMPLIFIER.RF SAFETY WARNING: (MOBILE ONLY) The outside antenna must be mounted with a separation distance of at least 15.5 inches from any of the vehicle occupants or nearby persons and must not be co-located or operating in conjunction with any other antenna or amplifier. Use of a cellular amplifier with antenna gains higher than 5.12dBi is in violation of FCC regulations for which the offender is fully liable. All Wilson Mobile Antennas are 5.12dBi or less.WARNING: (IN-BUILDING ONLY) Lightning protection is recommended for all in-build-ing installations.RF SAFETY WARNING: (IN-BUILDING ONLY) When using in-building, the outside antenna must be fixed-mounted on an outdoor permanent structure with a separation of at least 20 feet from all persons during normal operation.4.2 Installing The Amplifier4.2.1 Select a suitable location to mount the AMPLIFIER.• In vehicle installation - under the dash or vehicle seat• In building installation - on a wall or ceilingNOTE: Mount the AMPLIFIER away from direct sunlight, excessive heat and/or mois-ture. The amplifier needs proper ventilation. DO NOT place the amplifier in an air-tight enclosure. Use #6 screws to mount the amplifier.4.2.2 Connect the outside antenna to the AMPLIFIER side labeled “OUTSIDE ANTENNA”.4.2.3 Connect the ADAPTER EXTENSION CABLE to the AMPLIFIER side labeled “CELLULAR PHONE”.4.2.4 An external antenna adapter is required (sold separately) to connect theAMPLIFIER to the cellphone. External antenna adapters connect directly to the antenna extension cable.4.2.5 Connect the DC power supply to the AMPLIFIER. Verify that both the OUTSIDE ANTENNA and the ADAPTER EXTENSION CABLE are connected before powering up the AMPLIFIER.NOTE: Visit our website at www.wilsonelectronics.com for the latest adapter cross
45         In-BuildingInstallationMobileInstallation
45reference chart. If your phone’s adapter is not available from your retailer contact us at 1-866-294-6996 and we will help you locate one in your area. For further assistance contact our technical support Toll-Free at 1-866-294-1660.NOTE: iDEN Antennas are recommended for iDEN Amplifier 814001.Dual Band #811201 PCS 1900 SpecicationsDual Band #811201AMPS SpecificationsFrequency 1850-1910MHz Uplink1930-1990MHz Downlink824-849MHz Uplink869-894MHz DownlinkGain (up/down) Cell Site Controlled-Max 11db/11dbCell Site Controlled-Max 10db/10dbFlatness (up/down) (+/-2dB / +/-2dB) (+/-2dB / +/-3dB) Max RF (up/down) (+33dBm / +15dBm) (+35dBm / +15dBm)Noise Figure (down) (3.5dB nominal) (3.5dB nominal) Isolation Uplink/Downlink 90dB Uplink/Downlink 90dBPower Consumption 1.5A@12V 1.5A@12VThe information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no responsibility is assumed by Wilson Electronics, Inc. for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use.Copyright © 2004 Wilson Electronics, Inc.5. AMPLIFIER SPECIFICATIONSConnectors FME-Male 50 OhmsDimensions 5.5x4.3x1.4 (inch) or 14.0x10.8x3.5 (cm)Weight 1.32 Pounds or 600GiDEN #814001 AMPS #811101Frequency 806-821MHz Uplink851-866MHz Downlink824-849MHz Uplink869-894MHz DownlinkGain (up/down) Cell Site Controlled-Max 10/10dbCell Site Controlled-Max 10/10dbFlatness (up/down) (+/-2dB / +/-3dB) (+/-2dB / +/-3dB) Max RF (up/down) (+35dBm / +15dBm) (+35dBm / +15dBm)Noise Figure (down) (3.5dB nominal) (3.5dB nominal) Isolation Uplink/Downlink 90dB Uplink/Downlink 90dBPower Consumption 1.5A@12V 1.5A@12V
676. OPTIONAL ACCESSORIES/ANTENNA OPTIONS6.1 Coax Cable Extensions 50Ω (see chart on pg.7)6.2 Antenna Options (see chart on last page)6.3 N-Female To FME-Female Adapter - Adapts 9913 Coax to the 814001 Bi-directional Amplifier.6.4 Lightning Suppressor (In-Building application)WARNING: Lightning protection is recommended for all In-Building installations.6.5 Hardwire Power Supply Kit.7. WARNINGSWARNING: Verify that both the outside antenna and adapter extension cable are connected before powering up the AMPLIFIER.RF SAFETY WARNING: (MOBILE ONLY) The outside antenna must be mounted with a separation distance of at least 15.5 inches from any of the vehicle occupants or nearby persons and must not be co-located or operating in conjunc-tion with any other antenna or amplifier. Use of a cellular amplifier with antenna gains higher than 5.12dBi is in violation of FCC regulations for which the of-fender is fully liable. All Wilson Mobile Antennas are 5.12dBi or less.WARNING: (IN-BUILDING ONLY) Lightning protection is recommended for all in-building installations.RF SAFETY WARNING: (IN-BUILDING ONLY) When using in-building, the outside antenna must be fixed-mounted on an outdoor permanent structure with a separation of at least 20 feet from all persons during normal operation.Optional Accessories         
678. TECH SUPPORTIf you need further assistance with your installation:1) Call us Toll-Free at 866-294-16602) E-mail tech support at tech@wilsonelectronics.com3) Go to www.wilsonelectronics.comOur Hours of Operation are: 8:00 AM – 4:30 PM (Mountain Time)951101 5’ Extension Cable RG 58 Low Loss Coax (0.6 db loss)951102 10’ Extension Cable RG 58 Low Loss Coax (1.2 db loss)951103 15’ Extension Cable RG 58 Low Loss Coax (1.8 db loss)951104 20’ Extension Cable RG 58Low Loss Coax(2.4 db loss) Used with the YagiAntenna - (N-Male to FME Female)951108 20’ Extension Cable 9913Ultra Low Loss CoaxOnly use 9913 Low Loss Coax for extensions 20’ or longer (0.8 db loss)951105 30’ Extension Cable 9913Ultra Low Loss Coax(1.2 db loss)951106 50’ Extension Cable 9913Ultra Low Loss Coax(2.0 db loss)951107 100’ Extension 9913 Low Loss Coax (4.0 db loss)EXTENSION CABLE CHART (RG 58 - FME connectors / 9913 - N connectors)The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.Leaving the amplifier on in an unused vehicle for days may drain your battery. This can be avoided by plugging into an ignition switched outlet or by using the small white switch located on the power supply.
8                                                                                       For more options visitwww.wilsonelectronics.comOutside Antenna OptionsPictures Are Not To ScaleNot All Outside AntennaOptions Are ShownQuestions?1-866-294-1660www.wilsonelectronics.com15 DAYMONEY BACKGUARANTEEAll Wilson products have a 15 day money backguarantee with Proof of Purchase1 YEAR WARRANTYThe Wilson amplifier is warranted for one year against defects in workmanship and/or materials and will be repaired or replaced, at the discretion of the manufac-turer, to the original purchaser with dated proof of purchase or sales receipt.If you have questions about your amplifier please call technical support call 1-866-294-1660 or E-mail tech@wilsonelectronics.comMost warranty cases can be handled by taking the amplifier and the re-ceipt to the store where it was purchased. If inconvenient, the amplifier and a copy of the receipt, may be sent to the factory, at purchasers expense, where it may be repaired or replaced and returned shipping paid. Warranty does not cover damages caused by abuse, misuse, and negligence.

Navigation menu