Wilson Electronics 8013SB In Building Wireless PCS Smart Amplifier User Manual users manual

Wilson Electronics, LLC In Building Wireless PCS Smart Amplifier users manual

users manual

Wilson Electronics, Inc.3301 E. Deseret Drive, St. George, Utah 84790For additional technical support visitwww.wilsonelectronics.comPhone: 1-866-294-1660 Fax: 1-435-656-2432IN-BUILDINGWirelessThe term “IC:” before the radio certification number signifiesthat Industry of Canada technical specifications were met.PCS Smart Technology™ AmplifierInstallation GuideIn-Building Wireless PCS Smart TechnologyTM AmplierPART # 8013061850-1990 MHzFCC ID: PWO8013SBIC: 4726A-8013SB
231. PURPOSE OF THE AMPLIFIERThe PCS Smart TechnologyTM Amplier improves RF coverage for areas in which low signal strength is a concern.2. PACKAGE CONTENTS 2.1 Amplier 2.2 AC/DC 110 volt Power Supply3. HOW THE AMPLIFIER FUNCTIONSThe signal is received by the outside antenna from the cell site. The signal is then AMPLIFIED and transmitted to your phone through the inside antenna. When the phone transmits, the signal is received by the inside antenna and then AMPLIFIED and transmitted to the cell site through the outside antenna.4. AMPLIFIER INSTALLATION (see illustration on pg. 4 & 5)4.1 Installing the Wilson Cellular Outside AntennaWARNING: The outside antenna used with this amplier must be xed-mounted on an outdoor permanent structure with a separation of at least 20 feet from all persons during normal operation. 4.1.1 Select a location on the roof using your phone in test mode to nd the best signal strength. (See leaet titled PHONE TEST MODES)4.1.2 The outside antenna should be located in an area with at least a 3 foot radius clear of obstructions and other radiating elements. 4.2 Installing The AmplierWARNING: Connecting amplier directly to cell phone may damage phone.WARNING: Connect both antennas before connecting power to the amplier.4.2.1 Mount the AMPLIFIER on a wall or ceiling using #6 screws.NOTE: Mount the AMPLIFIER away from direct sunlight, excessive heat and/or moisture. The amplifier needs proper ventilation. DO NOT place the amplifier in an air-tight enclosure.4.2.2 Connect outside antenna to the amplier side labeled “OUTSIDE ANTENNA”.4.2.3 Connect inside antenna to the amplier side labeled “INSIDE ANTENNA”.4.2.4 Verify that both the outside and inside antennas are connected before connecting the AC-DC power supply to the power outlet.
234.4 Installing The Wilson Cellular Inside Antenna4.4.1 See antenna packaging for model specic instructions.4.4.2 The inside antenna should be centered in the weak signal area. The inside antenna should be at least 7 feet from the oor.FCC Separation WarningWARNING: The inside antenna used with this amplier must have a separation distance from all persons that is at least: 9 inches for the 2.5 dBi Dome antenna. 14 inches for the 7 dBi Panel antenna.The amplier must not be co-located or operating in conjunction with any other antenna or amplier.4.5 When covering multiple areas a 1900 MHz splitter can be used to allow for more than one inside antenna. Extension cables can also be used if the weak signal area is located far from the location of the outside antenna. For coax runs more than 20 feet use 9913 or equivalent coax.NOTE: For Maximum gain (60 dB), keep a separation distance of at least 50 feet between the outside and inside antennas. Closer spacings may be used, but may cause the amplier to automatically reduce its gain.NOTE: When using a Yagi antenna make sure the Yagi is pointed away from the inside antenna.ALL LIGHTS GREEN = 60 dB GAINLIGHT D OFF = 2 dB REDUCTIONLIGHT D & C OFF = 10 dB REDUCTIONLIGHT D, C & B OFF = 20 dB REDUCTIONLIGHT A RED = 40 dB REDUCTION4.3 Indicator Lights
45AC / DCPower SupplyAmplifierInside Antenna to Amplifier ConnectionCellSiteSupportsMultipleUsersOutside Antenna1900 MHz Yagi Antenna ShownOutside Antenna toAmplifier ConnectionInside AntennaOptional DomeAntenna ShownIf using a Yagi Antenna,Make sure the Yagi is not pointedtoward the inside antenna.AMPLIFIER PHYSICALSPECIFICATIONSConnectors N-Female 50 ohmsDimensions 4.5 x 3.5 x 1.25 inches 11.4 x 8.9 x 3.2 (cm)Weight 1.5 lbs / 0.7 kg
45For maximum gain, keep a separation distance of at least 50 feet between the outside and inside antennas.AC / DCPower SupplyAmplifierInside Antenna to Amplifier ConnectionCellSiteSupportsMultipleUsersOutside Antenna1900 MHz Yagi Antenna ShownOutside Antenna toAmplifier ConnectionInside AntennaOptional DomeAntenna ShownAMPLIFIER LAYOUTDIAGRAM5. AMPLIFIER SPECIFICATIONSPart Number 801306Gain 60 dBFrequency PCS1850-1910 MHz / 1930-1990 MHzLinear Output Power 30 dBmMax Output Power 3 wattsMax RF (up/down) +30 dBm / +30 dBmNoise Figure (typical) 4 dBFlatness (up/down) ± 4 dBIsolation > 90 dBPower Requirements 120 V AC 3 A MaxConnectors N-FemaleDimensions 4.5 x 3.5 x 1.25 (inch) 11.43 x 8.9 x 3.2 (cm) Weight 1.5 lbs / 0.7 kg
676. OPTIONAL ACCESSORIES/ANTENNA OPTIONSWARNING: Lightning protection is recommended for all installations. 6.1 3dB Dual-Band Splitter Part # 8599116.2 Coax Cable Extensions 50Ω (see chart on next page)6.3 Antenna Options:Inside Antenna Options Outside Antenna Option301103 - Magnet Mount 5 dBi 301124 - Yagi 13 dBi301106 - Low Prole 2.2 dBi301113 - Mini Magnet 2.12 dBi301121 - Dome 2.5 dBi301122 - Panel 7 dBi301123 - Dual Polarity Dome, Unity6.4 N-Male to FME-Male adapter Part # 9711136.5 Lightning Surge Protection Part # 8599027. TECH SUPPORTIf you need further assistance with your installation:1) Call Toll-Free 866-294-1660 8:00 AM – 4:30 PM (Mountain Time)2) E-mail tech support at tech@wilsonelectronics.com3) Visit www.wilsonelectronics.com8. WARNINGSWARNING: The outside antenna used with this amplier must be xed-mounted on an out-door permanent structure with a separation of at least 20 feet from all persons during normal operation.WARNING: The inside antenna used with this amplier must have a separation distance from all persons that is at least: 9 inches for the 2.5 dBi Dome antenna. 14 inches for the 7 dBi Panel antenna. The amplier must not be co-located or operating in conjunction with any other antenna or amplier.WARNING: Verify that both the Outside and Inside Antennas are connected before plug-ging in the AC/DC power supply to the power outlet.WARNING: Lightning protection is recommended for all installations. Lightning protection is required for warranty validation.The information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no respon-sibility is assumed by Wilson Electronics, Inc. for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use.Copyright © 2006 Wilson Electronics, Inc.
67951110 2’ Extension Cable RG58U Low Loss CoaxN-Male to FME-FemaleUsed with the Yagi antenna to help nd the optimum signal strength (for installation purposes only).951101 5’ Extension Cable RG58ULow Loss Coax0.6 dB loss951102 10’ Extension Cable RG58ULow Loss Coax1.2 dB loss951103 15’ Extension Cable RG58ULow Loss Coax1.8 dB loss951104 20’ Extension Cable RG58ULow Loss Coax2.4 dB loss, N-Male to FME-Female951113 2’ Extension Cable 9913 Equivalent Ultra Low Loss Coax0.08 dB loss, Jumper Coax - Can be used to con-nect a splitter behind an amplier.951108 20’ Extension Cable 9913 EquivalentUltra Low Loss CoaxOnly use 9913 Equivalent Low Loss Coax for extensions 20 feet or longer, 0.8 dB loss951105 30’ Extension Cable 9913 EquivalentUltra Low Loss Coax1.2 dB loss951106 50’ Extension Cable 9913 EquivalentUltra Low Loss Coax2.0 dB loss951117 75’ Extension Cable 9913 Equivalent Ultra Low Loss Coax3.0 dB loss951107 100’ Extension Cable 9913 Equivalent Low Loss Coax4.0 dB lossEXTENSION CABLE CHARTRG58U - FME connectors / 9913 Equivalent - N connectorsOperation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when mul-tiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.
Trucker 3/8"MountMiniMagnetMagnetMountLowProfile1900 MHzYagiDome Dual PolarityDomePanelOptional AccessoriesCoax Cable ExtensionUltra Low Loss CoaxLightning SuppressorFME Male toN-Male15 DAY MONEY BACK GUARANTEE All Wilson products have a 15 day money back guarantee with Proof of Purchase1 YEAR WARRANTYThe Wilson amplifier is warranted for one year against defects in workmanship and/or materials and will be repaired or replaced, at the discretion of the manufac-turer, to the original purchaser with dated proof of purchase or sales receipt.If any questions arise about an amplifier please call technical support toll-free 1-866-294-1660 or E-mail tech@wilsonelectronics.comMost warranty cases may be handled by taking the amplifier and the re-ceipt to the store where it was purchased. If inconvenient, the amplifier and a copy of the receipt, may be sent to the factory, at purchasers expense. It will be repaired or replaced and returned shipping paid. Warranty does not cover damages caused by abuse, misuse, and negligence.801306_006 / 04.06.06

Navigation menu