Wilson Electronics 277180 DUAL-BAND CHANNELIZED SIGNAL BOOSTER User Manual USERS MANUAL

Wilson Electronics, LLC DUAL-BAND CHANNELIZED SIGNAL BOOSTER USERS MANUAL

USERS MANUAL

Wilson® Electronics, Inc.Contents:Antenna Options & Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Quick Install Overview .......................................2Installation Diagram .........................................3Before Getting Started .......................................4Finding the Strongest Signal ..................................5Outside Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Installing the Inside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Installing a Wilson Electronics Signal Booster. . . . . . . . . . . . . . . . . . . . . 9Powering up a Wilson Electronics Signal Booster .................11LCD, Uplink & Downlink Directions ............................12Understanding the Signal Booster Light & LCD Screen ............12Warnings and Recommendations .............................15Guarantee & Warranty ......................................17Specifications .................................... Back CoverNote: This manual contains important safety and operating information. Please read and follow the instructions in this manual. Failure to do so could be hazardous and result in damage to your Signal Booster.Channelized800 MHzAdjustable GainIn-Building Wireless Smart Technology ™ Signal Boosters Appearance of device and accessories may vary.
1Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.2Installation Instructions for the Following Wilson Electronic Signal Booster:Channelized 800 MHz Adjustable Gain In-Building Wireless Smart Technology ™ Signal BoosterModel # 277180 FCC ID: PWO277180 IC: 4726A-277180The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. How it WorksWilson Electronics Signal Boosters are bi-directional devices that deliver service levels consistent with what would be expected in areas of high cell network coverage. They amplify a weak or shadowed signal in mobile, M2M, marine and in-building applications. When using a Wilson Electronics Signal Booster in conjunction with Wilson Electronics antennas, the outside antenna will collect the cell tower signal and send it through the cable to the Signal Booster. The signal is then amplified and re-transmitted through the Inside Antenna into the room. Cell phones and cellular data cards in that area then communicate with the improved signal. When a cell phone or cellular device transmits, the signal is received by the Inside Antenna, amplified by the Signal Booster and transmitted back to the cell tower through the Outside Antenna.Inside this PackageSignal BoosterAC/DC Power SupplyTo purchase, call Wilson Electronics Sales Department at: 800-204-4104We recommend using directional antennas with these boostersOutdoor Antenna OptionsIndoor Antenna Options & Accessories1. 800 MHz Yagi Cellular Antenna (301129) (Use with 807180)2. Wide Band Directional Antenna 700 MHz - 2700 MHz (304411)A. Wide-Band Panel Antenna 700-2700MHz (301135)B. 50 Ohm Lightning Surge Protector N-Connector (859902)Splitter options on page 321BANote: Kits may contain different accessoriesAppearance of device and accessories may vary.
12Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.Select a location to install the Signal Booster that is away from 1. excessive heat, direct sunlight, moisture and has proper ventilation. Do not place the Signal Booster in an air-tight enclosure. Select a location on the roof of the building to install the Outside Antenna. 2. Use a cell phone in test mode to find the strongest signal from the cell tower. See page 5. Visit www.WilsonElectronics.com to find the test mode function for your particular cell phone. Run the Outside Antenna cable to the Signal Booster and attach it to the 3. connector labeled “Outside Antenna” on the Signal Booster. Run the Inside Antenna cable to the Signal Booster and attach it to the connector labeled “Inside Antenna” on the Signal Booster. See page 8 for more information on running cable. Lightning Surge Protection is recommended for all in-building installations see page 7.Select a location for the Inside Antenna, preferably in the center of 4. where the signal needs to be amplified. A minimum separation distance of 20 vertical (within the null zone) or 50 horizontal feet is necessary for proper operation. If the inside coverage is not sufficient you may need to increase the separation distance even further (see installation diagram on pages 3 & 4). Before powering up the Signal Booster, verify that both the Outside 5. Antenna and the Inside Antenna are connected and check that all connections are tight. See page 9. Note: Be careful when plugging the connectors in so as not to bend the center pins on the connectors. Press yellow “CH Select” button to desired setting. Your channel will 6. show on the LCD screen. See page 11-12.The Signal Booster has been packaged with the gain control knobs 7. adjusted to the highest gain position. If light is not green, please refer to pages 12-14.Quick Install OverviewSee Installation Diagram on page 3. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660. Warning: Connecting the Signal Booster directly to a cell phone with use of an adapter will damage the cell phone and/or the Signal Booster.Wilson® Electronics recommends that all AC power supplies for home electronics be plugged into a Surge Protector Power Strip.
3Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.4Typical InstallationOutside AntennaInside AntennaInstallation Diagram(Optional second antenna for additional coverage).Power SupplyInside AntennaPreferred Method: Place the Inside Antenna in the ceiling facing down for the best coverage.Note: A Lightning Surge Protector is recommended for all building installations (sold separately). Make sure the protector is installed in line between the Outside Antenna and the Signal Booster. Null Zone: The area under the Outside Antenna, where the Outside Antenna radiates the least.Note: The Inside Antenna may be mounted on the wall directly under the Outside Antenna, in the null zone, if 20 feet of vertical separation can be maintained.
34Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.Before Getting StartedThis guide will help you properly install your Wilson Electronics Signal Booster. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment. Contact Wilson Electronics Technical Support with any questions at: 866-294-1660.Signal BoosterLightning Surge ProtectorSplitter(if using multiple inside antennas)(Optional third antenna for additional coverage).Inside AntennaSurge ProtectorPowerstrip
5Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.6Reasons for Weak Cellular SignalsAnyone who uses a cell phone or cellular data card knows the frustration of not being able to connect to or maintain a strong cellular signal. When this occurs, it is generally due to one of two reasons:Location of the Nearest Cell Tower – Cell towers are situated to 1. provide broad coverage; however, there are many areas in which signal strength may be reduced by topographic features or by local government restrictions on the height or placement of the towers themselves. Rural areas generally have fewer cell towers than urban regions.Natural and Man-Made Obstructions – Signal strength can also 2. be negatively affected by trees, hills, buildings, weather, and other obstructions. You may be relatively close to a cell tower but still unable to make a call. This often occurs in homes, offices and other buildings in which stucco, concrete or metal walls may block the signal.The Signal Booster works with two antennas. The Inside Antenna communicates with your cell phone and the Outside Antenna communicates with the cell tower. The Outside Antenna receives the cell tower signal and sends it through the cable to the Signal Booster, where it is amplified and transmitted through the Inside Antenna into the room. When the Inside Antenna picks up a signal from your cellular device, the Signal Booster amplifies that signal and transmits it through the cable, then through the Outside Antenna and back to the cell tower. (Note: The Signal Booster will only operate if there is an adequate signal to amplify.)Finding the Strongest SignalWhen installing your Signal Booster’s Outside Antenna, aiming it towards the best signal source from you service provider is important. The best way of getting the strongest signal is to have one person on the roof to rotate the Outside Antenna, which is connected to the Signal Booster. Turning the Outside Antenna about 45 degrees at a time, while the second person is watching the signal strength on the phone inside the building. This allows you to read the signal strength from the cell tower. It is preferable to have the phone in the test mode so the actual signal strength can be read, as bars are not the most accurate. Go towww.WilsonElectronics.com for help in finding the test mode for your phone. Always make sure the person inside the building gives the signal time to arrive and register on the phone (between 10-30 seconds for phone to reset to the signal reading).
56Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.Selecting a Direction for the Outside AntennaBefore selecting a location on the roof of the building to install the Outside Antenna, see page 8 for additional instructions. Use a cell phone in test mode to find the strongest signal from the cell tower (see page 5 for more information). To get the strongest signal possible, it is very important to set up your Outside Antenna properly. The Inside and the Outside Antenna must be mounted in such a way that they are able to pick up the best possible cell signal on the outside of the building and provide the best possible signal on the inside of the building. Mount the Outside Antenna as high as possible facing the cell tower in an area with the best possible signal coverage.Note: Never point the front of a directional antenna toward the Inside Antenna. See Figures 1 & 2 on page 10.-50dB -60dB -70dB -80dB -90dB -100dB -110dBEXCELLENT GOOD POOR NOSIGNALSignal Strength GraphCell TowerCell SignalOutsideWide Band AntennaSignal readings usually appear as a negative number (for example, -86). The closer you get to zero the stronger the signal. (See graph below).
7Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.8Cell TowerDrip hole on bottomInstalling Lightning Protection (sold separately)Outside Antenna InstallationThe antenna should be mounted as shown in the illustration above. The mounting bracket, included with antenna, is adjustable and will accommodate pipe diameters from 1.25” to 2” (pipe sold separately). Mount the antenna so that there is at least 3 feet of clearance in all directions around it. Position the antenna so that it has an unobstructed line of sight to the cell tower’s strongest signal. Make sure the antenna is not pointing across your own roof or at the Inside Antenna as this will cause the oscillation protection circuitry to shut down the Signal Booster. Warning: Lightning protection is recommended for all installations (Part #859902-50 Ohm shown below or 859988-75 Ohm). Take extreme care to ensure that neither you nor the antenna comes near any electric power lines.Install the Lightning Surge Protector (LSP) close to the Signal Booster. Attach the cable from the Outside Antenna to the surge protector, using a short length of low loss cable; attach one end to the LSP and the other to the Outside Antenna connector on the Signal Booster. Ensure the LSP is properly grounded (ground wire not included). LSP sold separately, go towww.WilsonElectronics.com or call 800-204-4104 to order.To the outside antennaGround WireLightning Surge ProtectionSignal Booster(not included)
78Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.Mounting Tips for Running Outside Antenna CableIf you are mounting the Outside Antenna on the roof of your building, we have found that it is easiest to run your cable underneath the down side of your roof’s flashing. If you have satellite TV service installed you may be able to follow the same route as the satellite TV cables that are already running from outside of your building to the inside. After routing the cable, we recommend sealing any areas where the cable passes into the building with cable bushings, silicone or a silicone-type sealant to keep your installation from leaking. If you are mounting the Outside Antenna to the outside wall of your home or building, the simplest way is to run the cable on the outside of the wall and attach it to the exterior of your home or office. Then drill a hole through the wall where you want the cable to appear on the inside of the building. Before drilling, make sure that there are no electrical outlets, sewer or water pipes, or electrical wiring in the wall that you are about to drill through as this could potentially harm you or damage the building.After drilling the required hole, run the cable through and seal it with cable bushings or a silicone-type sealant to enclose the hole that you have created. In some instances, it may be possible to run the cable up into the fascia of the attic overhang. In this circumstance, the cable will be accessible in the attic for further routing.Installing the Inside Antenna(Instructions are for optional Panel Antenna)Select a location for the Inside Antenna, preferably in the center of where the signal needs to be amplified. A minimum separation distance of 20 vertical feet is necessary for operation. If the inside coverage is not sufficient you may need as much as 75 feet of horizontal separation. See installation diagram on pages 3 & 4.Ceiling RaftersCeiling DrywallInside Antenna
9Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.10 Warning: An Inside Antenna must have a separation distance from all persons that is at least 15 inches for the Panel Antenna.Note: Wilson® Electronics recommends that all AC power supplies for home electronics be plugged into a Surge Protector Power Strip.In some cases, multiple Inside Antennas may be required, for instance if you have multiple rooms with poor signal. A signal may be split by using a splitter (sold separately). If using more than one Inside Antenna, a separation up to 75 horizontal feet may be necessary between Inside Antennas. See configuration on pages 3 & 4. Installing a Wilson Electronics Signal BoosterSelect a location to install the Signal Booster that is away from excessive heat, direct sunlight, moisture and that has proper ventilation. Do not place the Signal Booster in an air-tight enclosure. Recommended installation locations for in-building Signal Boosters are near a power outlet and in a closet or on a shelf.Note: It is important to have adequate air ventilation. Maintain at least 6 inches of clearance from surrounding objects. Be careful when plugging the connector in so as not to damage the center pins on the connectorsRun the Outside Antenna cable to the Signal Booster and attach it to the connector labeled “Outside Antenna” on the Signal Booster. Run the Inside Antenna cable to the Signal Booster and attach it to the connector labeled “Inside Antenna” on the Signal Booster. Note: For distances of 20 feet or more, use Wilson low loss cable.Optional Wide Band Inside Antenna (sold separately)Splitter Options:3-way (859980)4-way (859981)2-way(859957)
910Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.OutdoorAntennaInside PanelAntennaFigure 2INCORRECT INSTALLATIONNever point antennas toward each otherPoint antennas away from each otherSignal BoosterOutdoorAntennaInside PanelAntennaFigure 1CORRECT INSTALLATIONSignal Booster
11Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.12Powering up a Wilson Electronics Signal Booster1. Never point the front of a directional Outside Antenna toward the inside antenna. See Figures 1 & 2 on page 10.2. Ensure that both the outside antenna cable and the inside antenna cable are connected to the Signal Booster and the connections are tight before powering up the Signal Booster.3. Plug the 6-volt power supply into the Signal Booster input marked “6V DC” (carefully, to avoid damaging the center pin) and then into a wall outlet.4. If the Signal Booster does not have a green light, please see pages 12-14.5. Using multiple Signal Boosters in one installation could cause interference to the cell tower.6. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email tech@wilsonelectronics.com. Technical Support hours are 7 am to 6 pm MST.Channel Select DirectionsNote: For a list of channel options see tables on page 18.If you know your desired channel setting, press or hold down the 1. yellow CH Select button until that channel is displayed on the LCD screen. See page 12 for further instructions about the LCD screen display numbers.If you do not know your channel setting: 2. Option 1: Watch the signal strength on your phone inside the building. (To put your phone in test mode visit www.WilsonElectronics.com or call Wilson Electronics Technical Support Team at 866-294-1660.) This allows you to read the signal strength from the cell tower. Press the yellow CH Select button until you have the best signal. See page 5 & 6 on how to read the signal strength from the cell tower. Option 2: You may also contact your wireless service provider for optimal channel setting information.
1112Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.During installation mode the Signal Booster is resetting itself very quickly to aid the installer. The Signal Booster is equipped with one indicator light. For the first 15 minutes that the booster is plugged in, it is programed for a test and alignment period. During this time, the light and the LCD will do one of the following 5 things:Understanding the Signal Booster Light, LCD Screen and TroubleshootingDownlinkUplinkGAINCNTLMaxMinGAINCNTLMaxMin800CHSelectThe Uplink (UL)/Downlink (DL) gain 1. is displayed on LCD screen above the knobs. Turn knob to adjust. See page 14 for Overload information.The yellow CH Select (Channel) 2. button will select the channel.The Uplink (UL) knob limits only the 3. uplink gain, whereas the Downlink (DL) knob limits both the uplink and the downlink gain.You will typically adjust only the 4. downlink knob.If the Signal Booster is operating 5. normally the LCD Screen will appear as shown in Figure 3.LCD, Uplink & Downlink Directions800Figure 3Note: If after the initial 15 minutes you are not done with the installation, the Signal Booster can be reset and enter installation mode again by disconnecting and reconnecting the power supply from the booster.Uplink Gain (dB) Downlink Gain (dB)Channel
13Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.141. BLINKING GREENIf the Signal Booster is blinking green, the Signal Booster is operating properly. If you are happy with the coverage area in your building, then you are done. Blinking will stop after the 15 minute installation period.2. LCD SCREEN OVERLOADIf the LCD screen shows “OVERLOAD,” see Figure 4, the Signal Booster has automatically reduced gain to protect a nearby cell tower. First turn downlink (DL) gain control knob until the “OVERLOAD” is replaced with “UL CH DL” see Figure 5. The booster is now working with reduced gain. If the gain is not adequate for good coverage, you will need to turn the gain to maximum and then turn the outside antenna away from the cell tower until the “OVERLOAD” is replaced with “UL CH DL” see Figure 5. If the booster will not respond, turn the gain down 5 dB and move the outside antenna position until the “OVERLOAD” is replaced with “UL CH DL” see Figure 5.3. BLINKING ORANGEIf the light on the Signal Booster is blinking orange the Signal Booster is experiencing receiver overload. The Signal Booster has protection shut off circuits to prevent the disruption of cell towers. If the light is blinking orange, this indicates that the booster has shut down due to close proximity to a cell tower. First, turn down the downlink (DL) gain control until you get a blinking green light. The booster is now working with reduced gain. If the gain is not adequate for good coverage, you will need to turn the gain to maximum and then turn the outside antenna away from the cell tower until the light turns to blinking green. If the booster will not respond, turn the gain down 5 dB and move the outside antenna. Continue to adjust the gain and the antenna position until the light turns blinking green. Contact Wilson Electronics Technical Support Team for assistance: 866-294-1660.
1314Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.4. SOLID REDIf the light on the Signal Booster is solid red, this indicates that the Signal Booster has shut down on that frequency to prevent an oscillation (feedback). First, make sure that all the connections are tight. Then reduce the gain of the booster in small increments by rotating the downlink (DL) gain control, counter clockwise, waiting 5 seconds between each adjustment for the booster to reset. Continue this adjustment until the light turns blinking or solid green. When you are turning down the gain, you are reducing the inside coverage area. If the amount of coverage area is sufficient for your needs and the light is green, the installation is complete. If the coverage area is not large enough, it is necessary to increase the separation distance of the antennas by moving them horizontally or vertically farther apart, or both. Then increase the gain until the red light comes on, and then slightly keep decreasing the gain until the green or blinking green light appears. If after separating the antennas your coverage area is still too small, contact Wilson Electronics Technical Support Team for assistance: 866-294-1660.Note: Reduce the downlink gain if the phone shows good signal strength but can not make calls. This happens when the separation between the uplink and downlink gains is too much.If your installation takes longer than 15 minutes, it is possible to re-enter the installation mode by disconnecting and reconnecting the power supply from the Signal Booster.5. SOLID GREENThe indicator light on the Signal Booster will be a solid green after the first 15 minute installation period, if the unit is powered up and working properly.
15Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.16Warnings and Recommendations Warning: The outside antenna must always be located so the back or side points to the inside antenna. Never point the front of the outside antenna toward the inside antenna – this is to prevent oscillation. Warning: Connecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. Warning: Use only the correct Wilson Electronics power supply. Use of a non-Wilson Electronics product may damage your equipment. Warning: RF Safety: FCC regulations require that any fixed outside antenna used with this Signal Booster may not have gain (including cable & connector losses) that exceeds 15 dBi and must be located at least 27 inches from all people. Inside antennas must not exceed 4.1 dBi gain (including cable & connector losses) and must be located at least 8 inches from all people. The antennas shown on page 1 meet these requirements. Warning: Verify that both the outside antenna and the inside antenna are connected to the Signal Booster before powering up the Signal Booster.Recommendation: Omni directional antennas are not recommended with this Signal Booster.Recommendation: Lightning surge protection is recommended for all in-building installations.Recommendation: all AC power supplies for home electronics be plugged into a Surge Protector Power Strip.
1516Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.About Wilson ElectronicsWilson Electronics, Inc. has been a leader in the wireless communications industry for over 40 years. The company designs and manufactures Signal Boosters, antennas and related components that significantly improve cellular telephone signal reception and transmission in a wide variety of applications, both mobile (marine, RV, vehicles) and in-building (home, office, M2M).With extensive experience in antenna and Signal Booster research and design, the company’s engineering team uses a state-of-the-art testing laboratory, including an anechoic chamber and network analyzers, to fine-tune antenna designs and performance. For its Signal Boosters, Wilson Electronics uses a double electrically insulated RF enclosure and cell tower simulators for compliance testing.Wilson Electronics Signal Boosters feature patented Smart Technology ™ that enables them to automatically adjust their power based on cell tower requirements. By detecting and preventing oscillation (feedback), signal overload and interference with other users, these Smart Technology ™ Signal Boosters improve network cell phone areas without compromising carrier systems.All products are engineered and assembled in the company’s 55,000-square-foot headquarters in St. George, Utah. Wilson Electronics has product dealers in all 50 states as well as in countries around the world.
17Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.18This device complies with Part 15 of FCC rules. The transaction is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Wilson Electronics could void the authority to operate this equipment.30-Day Money-Back GuaranteeAll Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase.1-Year WarrantyWilson Electronics Signal Boosters are warranted for one (1) year against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson Electronics shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer if located within the continental U.S.This warranty does not apply to any Signal Booster determined by Wilson Electronics to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.RMA numbers may be obtained by phoning Technical Support at 866-294-1660.Disclaimer : The information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no responsibility is assumed by Wilson Electronics, Inc. for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use.
1718Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.One or more of the following U.S. Patent numbers may apply to the Signal Booster in this product – D596,614; D596,615; D563,381;7,729,669; 7,486,929; 7,729,656; 7,409,186; 7,783,318; 7,684,838; 12,714,994.807180 Uplink DownlinkChannel Options Lower Band Edge MHzUpper Band Edge MHzLower Band Edge MHzUpper Band Edge MHzA 824 835 869 880B 835 845 880 890Pass Bandwidth (BW) MHz-3 dB BW MHz -40 dB BW MHz -45 dB BW MHz10 10.1 12.9 13.2Channel Selection ChartChannel Filter CharacteristicsCopyright © 2011 Wilson Electronics, Inc. All rights reserved.
Signal Booster SpecificationsFCC ID: PW0277180IC: 4726A-277180 Channelized 800Model Number 277180Antenna connectors N TypeAntenna impedance 50 OhmsDimensions 5.7 x 4.2 x 1.5 inch (14.0 x 10.8 x 3.9 cm)Weight 1.27 lbs (0.544 kg)Frequency 824-890 MHz1Channels Passband Gain (nominal)800 MHz 70 dB Typical, 75 dB Maximum220 dB Bandwidth (nominal) Downlink800 MHz 12 MHzPower Output 800 MHzPower output for single cell phone (uplink) 29.8 dBmPower output for single received channel (downlink) 29.8 dBm3Power output for multiple transmitted channels (uplink) Maximum PowerThe maximum power is reduced by the number of channels: Number of channels 800 MHz2 23.3 dBm3 18.3 dBm4 17.2 dBm5 15.3 dBm6 13.7 dBm4Power output for multiple received channels (downlink) Maximum PowerThe maximum power is reduced by the number of channels: Number of channels 800 MHz2 24.1 dBm3 18.3 dBm4 18.1 dBm5 16.2 dBm6 14.6 dBmNoise Figure (typical downlink/uplink) 3.5 dB nominal Isolation > 90 dBPower Requirements 110-240 V AC, 50-60 Hz, 15 W3301 East Deseret Drive, St. George, UT 84790For additional Technical Support visit www.WilsonElectronics.com or email at: tech@wilsonelectronics.comPhone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432www.twitter.com/WilsonCellular www.facebook.com/WilsonCellularAIG #110980 - RevP - 11.17.11Notes:Nominal gain is the maximum gain at any frequency in the passband.1. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB lower than the 2. passband amplification. One of the frequencies is lower than the passband and the other is higher.The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the 3. rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.4.

Navigation menu