WINIA Electronics 7NFCMC902D 19-inch Color Monitor User Manual 902D

Dongbu Daewoo Electronics Corporation 19-inch Color Monitor 902D

Users Manual

COLOR MONITORModel No : 902DUSER’S GUIDE
NOTE : This equipment has been tested and found to complywith the limits for a Class B digital device, pursuant to Part 15of the FCC Rules. These limits in a residential installation.This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with theinstructions, may cuase harmful interference to radiocommunications. However, there is no guarantee thatinterference will not occur in a particular installation. If thisequipment does cause harmful interference to radio ortelevision reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different fromthat to which the receiver is connected. - Consult the dealer or an experienced radio, TV technician forhelp. This digital apparatus does not exceed the Class A/Class B(whichever is applicable) limits for radio noise emissions fromdigital apparatus set out in the Radio Interference Regulationsof the Canadian Department of Communications. Avis de conformité aux normes du Ministère desCommunications du Canada.Le present appareil numérique n’emet pas de bruitsradioélectriques depassant les limites applicables aux appareilsnumériques de Class A/de Class B (selon le cas) prescrites dansle règlement sur le brouillage radioélectrique édicte par leministère des communications du canada. IMPORTANT SAFEGUARDS FEDERAL COMMUNICATIONS COMMISSION RADIOFREQUENCY INTERFERENCE STATEMENTCANADIAN DEPARTMENT OF COMMUNICATIONSCOMPLIANCE STATEMENT1. Read all of these instructions.2. Save these instructions for later use.3. Unplug this monitor from thewall outlet before cleaning. Do notuse liquid cleaners or aerosolcleaners. Use a damp cloth forcleaning.4. Do not use attachments not recommended bythe monitor manufacturer as they may causehazards. 5. Do not use this monitor near water forexample, near a bathtub, washbowl, kitchen sink,or laundry tub, in a wet basement or near aswimming pool, etc. 6. Do not place this monitor on anunstable cart, stand, or table. Themonitor may fall, causing seriousinjury to a child or adult, andserious damage to the appliance. 7. Slots and openings in thecabinet and the back or bottom areprovided for ventilation, and toensure reliable operation of themonitor and to protect it fromoverheating, these openings must not be blockedor covered. The openings should never beblocked by placing the monitor on a bed, sofa,rug, or other similar surface. This should neverbe placed near or over a radiator or heat register.This monitor should not be placed in a built-ininstallation such as a bookcase unless properventilation is provided.8. This monitor should be operatedonly from the type of power sourceindicated on the marking label. Ifyou are not sure of the powersupplied to your home, consultyour monitor dealer or local power company.9. This monitor is equipped with a3-wire grounding type plug, a plughaving a third (grounding) pin. Thisplug will only fit into agroundingtype power outlet. This isa safety feature. If you are unable to insert theplug into the outlet, contact your electrician toreplace your obsolete outlet. Do not defeat thepurpose of the groundingtype plug. 10. Do not allow anything to reston the power cord. Do not locatethis monitor where the cord will beabused by persons walking on it. 11. Follow all warnings and instructions markedon the monitor. 12. For added protection for thismonitor during a lightning storm,or when it is left unattended andunused for long periods of time,unplug it from the wall outlet. Thiswill prevent damage to the set due to lightningand powerline surges. 13. Do not overload wall outlets and extensioncords as this can result in fire or electric shock. 14. Never push objects of any kind into thismonitor through cabinet slots, as they may touchdangerous voltage points or short out parts thatcould result in a fire or electric shock. Never spillliquid of any kind on the monitor. 15. Do not attempt to service thismonitor yourself as opening orremoving covers may expose youto dangerous voltage or otherhazards. Refer all servicing toqualified service personnel. 16. Unplug this monitor from the wall outlet andrefer servicing to qualified service personnelunder the following conditions: a. When the power cord or plug is damaged orfrayed. b. If liquid has been spilled into the monitor. c. If the monitor has been exposed to rain orwater. d. If the monitor does not operate normally byfollowing the operating instructions. Adjust onlythose controls that are covered by the operatinginstructions as improper adjustment of othercontrols may result in damage and will oftenrequire extensive work by a qualified technicianto restore normal operation. e. If the monitor has been dropped or the cabinethas been damaged. f. When the monitor exhibits a distinct change inperformance this indicates a need for service. 17. When replacement parts arerequired be sure the servicetechnician has used replacementparts specified by the manufacturerthat have the same characteristicsas the original part. Unauthorized substitutionsmay result in fire, electric shock, or otherhazards. 18. Upon completion of any service or repairs tothis monitor, ask the service technician toperform routine safety checks to determine thatthe monitor is in safe operating condition. CAUTION:Any changes ormodifications notexpresslyapproved by theparty responsiblefor compliancecould void theuser’s authority tooperate theequipment.
Bitte lesen Sie alle diese Informationen, bevor Sie das Gerät inBetrieb nehmen! Lesen Sie sich außerdem dieBedienungsanleitung komplett und sorgfältig durch, da nur indiesem Fall eine problemlose Inbetriebnahme erwartet werdenkann. •Achten Sie darauf, daß das Gerät nur in eine 230V Schuko-Steckdose eingesteckt wird. •Die Steckdose sollte jederzeit frei zugänglich sein um beieinem evtl. auftretenden Notfall das Gerät schnell vom Netzzu trennen. •Achten Sie desweiteren darauf, daß die Netzanschlußleitungnicht mechanisch beansprucht oder sonstwie beschädigtwird. •Offnen Sie das Gerät niemals! Im Inneren befinden sichTeile mit gefährlicher Spannung. •Bevor Sie das Gerät reinigen, ziehen Sie bitte denNetzstecker aus der Steckdose. Säubern Sie dann das Gerätmit einem feuchten (keinesfalls tropfnassen) Lappen. •Die in diesem Gerät entstehende Röntgenstrahlung istausreichend abgeschirmt (Ortsdosisleistung in 0.1mAbstand weniger als 1.0µ Sv/h). Beschleunigungsspannungmaximal 29Kv. •Stellen Sie das Gerät an einem ergonomisch günstigen Ortauf und sorgen Sie dafür, daß der Monitor mit nach GS-VW-SG7 geprüfter Peripherie betrieben wird, da nur unterdiesen Umständen ein optimaler ergonomischer Betrieb desGerätes sichergestellt ist. Falls Sie dennoch Fragen haben, auf die dieBedienungsanleitung keine hinreichende Antwort geben kann,so kontaktieren Sie bitte den nächsten Fachhändler. Maschinenlärminformationsverordnung 3. GSGV, 18.01 1991:Der arbeitsplatzbezogene Schalldruckpegel beträgt 70 dB (A)oder wenigergemäß ISO 7779. DECLARATION OF CONFORMITYWe, Manufacturer / Importer DAEWOO ELECTRONICS CO., Ltd 541, 5-Ga, Namdaemoon-Ro, Jung-Gu Seoul, Korea declare under our sole responsibility that the product, Color Display monitor 902Dto which this declaration relates is in conformity with the following standard(s) or other normative document(s) Safety : EN60950/1992/A1:1993/A2:1993 A3:1995/A4:1997EMC : EN 55022/8.1994, EN 50082-1/1992EN 60555 Part 2, 3/1987following the provisions of 89/336 EEC-EMC Directive and the provisions of 73/23 EEC-Low Voltage Directive. Handed over by : S.Lee, Managing Director. Display Business Division Jan, 1999 Seoul Signature: S.Lee, Managing Director. Display Business Division. DAEWOO ELECTRONICS Co., Ltd WICHTIGE INFORMATIONEN
Emission Characteristics Tested by SEMKOA sample of this type has been tested and has showncompliance with theguidelines in the swedish documentTCO’ 95.This product is also designed for IT power system with phaseto phase voltage of 230V. The power cord is used as a main disconnect device.Disconnect the power cord before servicing. The outlet mustbe installed near the monitor and must be easily accessible.As an ENERGY STAR Partner, Daewoo Electronics Co., Ltd.has determined that this product meets the Energy Starguidelines for energy efficiency.The appliance is not intended for use by young children orinfirm persons without supervision ;Young children should be supervised to ensure that they do notplay with the appliance.
Introduction ............................................................ 1Product Features ................................................ 2Setup ........................................................................ 3Connecting the Signal Cable and Power Cord ... 3Connecting to the Macintosh Computer ............ 4Power Management System ............................... 5DDC for Plug & Play ......................................... 5Operation & Adjustment ....................................... 6Specifications ........................................................ 14Factory Preset Timings ........................................ 16Troubleshooting .................................................... 17AppendixDescription for D-sub ConnectorThis manual explains how to correctly install, operate andget the best performance from your monitor. Please readthis user’s manual carefully before installing yourmonitor, then keep it near your monitor for quickreference. First, please check that the contents of the carton boxcorresponds with the following checklist : •Color monitor •Power cord •User’s manual •Warranty Card (Optional)If there is any item missing or damaged, please contactyour dealer. Please keep the carton box and packingmaterials so that you may properly store or transport yourmonitor.1CONTENTS INTRODUCTION
3CONNECTING THE SIGNAL CABLE ANDPOWER CORD1. Turn off the computer and monitor.2. Connect the 15 pin D-sub connector to the output port ofthe video card in your computer.3. Tighten the screws of connector.4. Plug the power cord into the AC receptacle located atthe back of the monitor. 5. Plug the other end of the power cord into the AC outlet.Signal CablePower CordPRODUCT FEATURES •The convenient and user-friendly on-screen displayallows for easy and accurate adjustments of horizontaland vertical screen size and position, geometry andscreen color. •The monitor supports a safe working environment instrict compliance with the MPR II standard for lowemissions(TCO 95 optional).•The monitor complies with the VESA Display DataChannel (DDC) specification for “Plug & Play”compatibility. Advanced microcircuitry makes set-upand configuration fast and effortless. •The monitor features Advanced Color Controls forfine-tuning to meet your own personal tastes orapplication requirements. Use the on-screen controlsto adjust the color temperature, RGB gain value forthe best possible screen color and intensity. •Press the menu button and activate the Self-Diagnosismenu to determine whether your monitor isfunctioning normally, not receiving a signal or isreceiving a signal that is out of scanning range.•Activate the higher refresh rates of the monitor tostabilize the screen and eliminate the annoying flickerthat contributes to eye-strain and headaches. •The “borderless” full-screen display capability worksunder all graphic modes and provides a larger viewingarea than conventional monitors, giving you a betterpicture with more workspace. 2
54POWER MANAGEMENT SYSTEM If you use the monitor with a computer which complieswith the power saving program, you can set the monitorto go blank when the system has remained unused for aperiod of time. To specify the period or to disable thisfeature, set the system timeout field of the computer’ssystem setup program or use special software for powersaving. See the computer user’s manual for the details ofusing the system setup. While the monitor is in powersaving mode (blank screen), it consumes less power thannormal state; the color of the power LED will indicate thestate. To restore the screen image, press any key of yourkeyboard or move your mouse. If the signal cable isconnected loosely or disconnected, the power savingfeature will not operate.DISPLAY DATA CHANNEL (DDC) FOR PLUG &PLAYIf you use the monitor with a computer which complieswith DDC1/2B/CI/2B+of VESA, the Host-Video Cardautomatically configures itself without your interventionin a way that best fits the attached monitor. The DisplayData Channel, DDC, allows the monitor to inform thehost system about configuration information for optimumuse of the monitor. Use of the Video Card utility is notrequired to match the resolutions and refresh rates of themonitor and video card.CONNECTING TO THE MACINTOSHCOMPUTER 1. Turn off the computer and monitor. 2. Attach the Macintosh cable adapter to the Macintoshvideo card. 3. Tighten the screws on the cable adapter. 4. Connect the signal cable provided with your monitor tothe other end of the Macintosh cable adapter. 5. Tighten the screws between the Macintosh cableadapter and the signal cable.Macintosh Adapter(Optional Accessory)Signal Cable
76Key ProcessDEUTSCHENGL SHESPAÑOLFRANCA STAL ANO+ + + Start OPERATION & ADJUSTMENTMove cursor to the right window from the MENUwindow.Increase the value of any selected FUNCTION.Move cursor to the left window from the MENUwindow.Decrease the value of any selected FUNCTION.Launch OSD(On-Screen Display) MENU window.Move cursor to the high window from the MENUwindow.Move cursor to the low window from the MENUwindow.Control PanelMENU+
9Select language for OSD (5 languages).LANGUAGECenter Menu FunctionsLanguage Menu FunctionAdjust the position of the displayhorizontally(left or right) and vertically(up or down). H. CENTER & V. CENTER Color Menu FunctionsChoose different preset colortemperatures or set your own customizedcolor parameters.Adjust the red gain.Adjust the green gain.Adjust the blue gain.COLOR TEMPRED GAINGREEN GAINBLUE GAINAdjust the red bias.Adjust the green bias.Adjust the blue bias.RED BIASGREEN BIASBLUE BIAS8•When you choose the icon on the OSD window, youcan exit the OSD screen. Hot KeyBRIGHTNESS CONTRAST
1110Geometry Menu FunctionsAdjust the left and right margins for moreconvex or more concave margins.• Image turns to by .• Image turns to by . Adjust the trapezoid of the screen bymoving the lines inward or outward.• Image turns to by .•Image turns to by . Adjust the side balance when the sides ofthe screen are bowed towards left or right.• Image turns to by .• Image turns to by . Adjust the parallelogram when the screenis leaning left or right.• Image turns to by .• Image turns to by . Adjust the rotation when the screen istilted left or right.• Image turns to by .• Image turns to by . Adjust the pin S control when the sides ofthe screen are in a S shape.• Image turns to by .• Image turns to by . PINCUSHIONTRAPEZOIDPIN BALANCEROTATIONPIN S ControlPARALLELOGRAMAdjust the pin W control when the sidesof the screen are in a W shape.• Image turns to by .• Image turns to by . PIN W ControlSize Menu FunctionsScreen Menu FunctionsAdjust the width (horizontal size) and theheight (vertical size) of the display.H. SIZE & V. SIZE Adjust the horizontal picture moirecancellation.Adjust the vertical picture moirecancellation.H. MOIREV. MOIREAdjust the focus image.FOCUSH. LINEARITYV. LINEARITYAdjust the horizontal linearity.Zoom Menu FunctionZOOM Adjust the display width & height at thesame time.Adjust the vertical linearity.
1312Self DiagnosisWhen the monitor doesn’t display, if you press any key,Self Diagnosis screen is displayed. Self Diagnosisfunction checks if the status of the monitor is No Signalor Out of range.No Signal screen is displayedwhen the D-Sub signal connectoris not connected or the status ofthe monitor is on DPMS mode.Out of Range screen is displayedwhen the applied frequency isunder or over normal range.Normal rangeH : 30 - 95 KHzV : 50 - 160 HzUtility Menu FunctionsDisplay horizontal & vertical frequencyand polarity.Degauss the display and restore imagequality.Reset the screen to the Factory PresetDisplay Settings.DEGAUSSSTATUSPOWER SAVERDisplay a RGB Color Bar to determinewhether the screen color is expressednormally or not.YES : VESA DPMS operation.NO : NO DPMS operation.TEST PATTERNRECALL
1514Tilt/Swivel RangeTilt : 5° forward, 10° backwardSwivel : ±45° leftward, rightwardDimension(set with stand)466(W) X 475.5(H) X 468.5(D) mm18.3(W) X 18.7(H) X 18.4(D) inWeight(net/gross)23.5/ 27.5 Kg51.8/ 60.6 lbsOperating EnvironmentTemperature : 10 ~ 40°C /50 ~ 104°FRelative Humidity : 8 ~ 80%Storage EnvironmentTemperature : - 20 ~ 45°C /- 4 ~ 113°FRelative Humidity : 5 ~ 90%Picture TubeType : 19-inch, Flat Square Tube type(18-inch, viewing area)Dot Pitch : 0.26 mm Face Treatment : Anti-reflect / Anti-staticVideoInput Signal : R.G.B. AnalogPixel Clock (=Rate) : 203 MHzInput Sync : TTL, separate negative / positiveH+V Sync. on Green, negativeComposite H+V Sync. negative / positiveScan FrequencyHorizontal : 30 - 95 KHz (automatic)Vertical : 50 - 160 Hz (automatic)Max. Resolution1600 dots X 1200 lines (at 75 Hz)Power SourceFree Voltage (100-240 Vac, 50/60 Hz)Display AreaStandard Display Area : 350(H) X 262(V) mm 13.8(H) X 10.3(V) inFull Screen Size : 365.8(H) X 274.3(V) mm14.4(H) X 10.8(V) inPower ConsumptionMax. 120 WSPECIFICATIONSState Recovery Time Power LEDOn None GreenStand-by Green: 1 secondSuspend Amber : 0.5 second3 secondsOff - Amber
1716TROUBLESHOOTINGCheck if POWER SWITCH and COMPUTERPOWER SWITCH are in the on position.Check if the signal cable is correctly connected tothe video card. Check if the pins of D-sub connector are not bent.Check if the computer is in the power saving mode. Check if POWER SWITCH is in the on position.Check if the power cord is correctly connected.Check if the signal cable is suitable to the video card.Adjust H & V SIZE or H & V POSITION to get theproper image.Keep the devices that may cause electrical interference away from the monitor. See the FCC information at the front cover of themanual.Operate DEGAUSS once.Adjust CONTRAST and BRIGHTNESS.Operate DEGAUSS once.Adjust PINCUSHION/TRAPEZOID.SymptomNo picture.POWER LED is notlit.Image is unstable.Image is notcentered, too smallor too large.Picture bounces or a wave pattern ispresent in thepicture.Color looks blotchy.Picture is blurred.Edges of availablearea on the screenare not straight.CheckFACTORY PRESET TIMINGSThis monitor has stored above-mentioned 6 timings in factory. You cansave up to 23 modes in the user memory automatically. Please note that ifyou save to user memory over twenty three times, the first mode saved willbe replaced with your twenty fourth mode.Mode H.Freq (KHz) V.Freq(Hz) RemarkVGA 640 X 480 31.5 60 Non-interlacedVGA 720 X 400 31.5 70 Non-interlacedVESA 46K 800 X 600 46.9 75 Non-interlacedVESA SVGA 85 800 X 600 53.7 85 Non-interlacedVESA 60K 1024 X 768 60.0 75 Non-interlacedVESA/85 1024 X 768 68.7 85 Non-interlacedResolution(dots Xlines)
18DESCRIPTION FOR D-SUB CONNECTORAPPENDIXPin123456789101112131415SignalRedGreenBlueGNDGNDGND-RedGND-GreenGND-BlueReservedGND-H.SyncGND-V.SyncBi-directional Data(SDA)Horizontal SyncVertical Sync(VCLK)Data Clock(SCL)161510*GND=Ground

Navigation menu