Voxx Electronics DEI7752 Hand Held Security/Remote Control Transceiver User Manual pages 22 to 30

DEI Headquarters, Inc. Hand Held Security/Remote Control Transceiver pages 22 to 30

user manual pages 22 to 30

22 © 2008 Directed Electronics. All rights reserved.9ALLPager Off 30ALLTimer Mode10ALLPager Vibe On 31ALLManual Transmission En-abled11ALLPager Tone On 32ALLCar 112ALLSiren 33ALLCar 213ALLSilent Mode 2 34ALLThermometer very cold14ALLTransmit 35ALLThermometer cold15ALLReceive 36ALLThermometer comfortable16ALLOut of Range 37ALLThermometer warm17ALLSensor 38ALLThermometer hot18ALLSensor Bypassed 39ALLDefroster19ALLAll Zones 40 Arrow20ALL1 41ALLSound Wave21ALLCar Door 42ALLLarge Siren➤ Multi-car control capability You can operate the 2-way remote control system for two cars, with full command capability for both vehicles.
23© 2008 Directed Electronics. All rights reserved.While holding a command button and transmitting, the car icon at the top of the remote control will blink in groups to indicate which Car is being controlled. Car 1: 1 blink• Car 2: 2 blinks• To change the Car to be operated: Two Way Remote Press/hold the A U X button for 3 seconds or until the remote beeps and the text reads Car 1 or Car 2. Pressing the A U X button will scroll between the two.. This will indicate which car the remote currently operates. One Way RemotePress and hold the A U X button until the amber light blinks once or twice indicating current vehicle (one blink = car 1. 2 blinks = car 2) to scroll from one to the other press the A U X button again.Using the system➤ Arming the systemTo arm the system, press the A U X button on the remote control.The siren in the vehicle will “chirp” once and the parking lights will flash once. If the power door locks have been connected, the doors will lock. The system will automatically check for errors when it arms. The 2-way remote will “chirp” once and blink the LOCK indicator to
24 © 2008 Directed Electronics. All rights reserved.confirm arming. If no arm confirmation is received, the remote will give the Out-Of-Range signal.If errors are found when arming:If an alarm trigger zone – such as a door, the trunk, the hood, or a sensor, was active at the time of arming, the system will “bypass”, or ignore, this trigger zone. This allows the system to continue to protectyour vehicle using the remaining trigger zones.You are notified of this active zone immediately after arming the system. The siren in the vehicle will “chirp” again and the parking lights will flash again. The Status LED indicator in the vehicle will blink in a pattern to indicate the active zone number error which was found (See Table of Zones on page 36). The 2-way remote control will sound a short “error” tone.Arming without the chirp (Silent Arm): Press the A U X button at the bottom of the remote once, and then press the A U X button. The system will arm without the confirmation chirp. The parking lights will flash once. The 2-way remote will blink the LOCK in-dicator to confirm arming. If no arm confirmation is received, the 2-way remote will give the Out Of Range signal.➤ While the system is armedFail-Safe Starter Kill• The starter is disabled by the system’s Fail-Safe starter kill.Alarm ResponsesThe security system can generate two levels of alarm: Warn Away - Soft
25© 2008 Directed Electronics. All rights reserved.siren chirps and flashing parking lights. The purpose of Warn-Away is to warn a would-be thief next to your vehicle that the vehicle is protected, but in a manner that does not call attention to it from more than a few feet away.Full Alarm Trigger Sounds the siren at maximum volume and ashes the parking lights. The default duration of the Full Alarm is 30 seconds. This can be pro-grammed to any duration from 30 to 60 seconds manually. Ask your authorized dealer for details. Pages the 2-way remote control. If in range, the two way remote will display what triggered the alarm.Warn-Away response is triggered by:Lesser or lighter vibrations or impacts (detected by the Stinger • Doubleguard shock sensor)Opening a door: the Progressive Door Trigger feature will sound • the Warn Away response, followed immediately by Full AlarmAny attempt to start the car: the Progressive Ignition Trigger will • first sound the Warn Away response, followed immediately by Full Alarm.An optional Proximity Sensor (508D) triggered in the outer zone.• Full Alarm response is triggered by:Heavier impact to the vehicle (detected by the Stinger Double-• Guard shock sensor).Opening the trunk or hood.• Opening a door: the Progressive Door Trigger feature will first •
26 © 2008 Directed Electronics. All rights reserved.sound the Warn-Away response, followed immediately by Full Alarm.An optional sensor, such as an optional Proximity Sensor triggered • in the inner zone.Paging SignalsIf the Full Alarm response is triggered, the 2-way remote control will be sent a paging signal by the in-car system.Note: Call the police immediately if you witness a crime in progress. Paging range varies with terrain and environmental conditions.➤ Modified Arming ModesThe Responder LC gives you an unprecedented level of control over how it will protect your car. “Normal arming” means that all the Re-sponder LC security features are active automatically. You can turn some security features off on a one-time basis.Turning off the Warn Away responseAfter arming, you can turn off the Warn-Away response on a one-time basis.Press the 1. A U X button twice.Press the 2. A U X button.The A U X LED flashes and the remote sounds an error tone.Now, slight impacts or vibrations will not trigger Warn-Away. Heavy impacts will still trigger Full Alarm.Note: The next time you arm the system, Warn-Away will work normally.
27© 2008 Directed Electronics. All rights reserved.Turning off the Sensor Full Trigger responseYou can completely disable the Stinger Doubleguard Shock Sensor and any added optional sensors on a one-time basis. The entry points (doors, hood, etc.) will still be monitored. All sensors will not be able to trigger the Warn-Away response or the Full Alarm response.After disabling Warn-away response, press the 1. A U X the button twice.Press the 2. A U X button.Note: The next time you arm the system, the shock sensor will work normally.Silent Mode 2 - Turning off the sirenYou can turn off the vehicle siren and flashing lights on a one-time basis, leaving the system’s paging feature as the only alarm response.Note: Call the police immediately if you witness a crime in progress. Paging range varies with terrain and environmental conditions. Full Silent Mode.In this mode, the siren cannot be triggered, but any trigger will cause the 2-way remote to be paged. Press the A U X button four times, and then press the A U X within five seconds. Sensor Silent ModeIn this mode, a sensor cannot trigger the siren, but will cause the 2- way remote to be paged. All entry points (doors, hood, etc.) will still trigger the siren.Press the A U X button three times, and then press the A U X button. Note: The next time you arm the system, it will function normally.
28 © 2008 Directed Electronics. All rights reserved.➤ Disarming the SystemWhile the system is armed normally:Press the • A U X button once.The siren in the vehicle will “chirp” twice, and the parking lights will ash. The 2-way remote will “chirp” twice and the A U X LED indicator will blink.If you hear four chirps on disarming, the system was triggered in your absence. Immediately look at the Status LED in the vehicle and count the number of flashes between pauses. This number is important, it tells what triggered your alarm. See Disarming section under Diagnostics on page 34 for more details.If you hear five chirps on disarming, the system was repeatedly trig-gered in your absence. Immediately look at the Status LED in the vehicle and count the number of flashes between pauses. This number is impor-tant, it tells what triggered your alarm. The door locks (if connected) will unlock, and the parking lights will flash. While the alarm is triggering: Press the A U X button on the remote. The siren will stop sounding and disarm the alarm system. High-Security DisarmingIf you want the Full Alarm response to stop without unlocking the doors, press the A U X button. The system will re-arm and the current alarm re-sponse will reset. ➤ System override
29© 2008 Directed Electronics. All rights reserved.To disarm the system without a remote control:You will need to use your Override Switch located on your systems control center (see diagram below) to disarm the system. The Override Switch disarms the system only if you have the vehicle key.2. Radious will be if not specied.1. Tex ture is same as3. Body color :INJECT TOLERANCE SPEC.*Tolerance please refer specication of tolerance limits "c"120~300DIMENSION30~120UNDER 60.40 0.800.200.100.08A±GRADE6~30B±0.400.200.162.00C±0.400.800.30 DEINUTEKFELIXVICTO RAPPD BYUNIT:M/MCODEMATERIALFINISHSCALE:1:1YG FSHEET DRN BYCHK BY11/20/07OFDATEA4TITLEDEPTSIZEREV.1REVISIONSDESCRIPTIONCORPORA T ION OLED IVU94I0600DRAWING NO0REVDATE DRN.94I0600CASE P/N:IADGH0A1KEY P/N:IKDEL0A036.3211.5010.44%2'<0$7(5,$/+,+($7$%689%/$&.To check proper operation: Open the door. The alarm will sound.• Immediately insert the key into the ignition and turn it to the RUN or ON position. (all the indicators in the dash will turn on). Press the Override Switch once.Note: The Override Switch feature allows you to select a specific number of presses needed to disarm the alarm. If the Override Switch has been programmed to a new number of presses by your authorized dealer, that number should be indicated below.Override Switch Number ___________
30 © 2008 Directed Electronics. All rights reserved.Using the remote start➤ Before using your Remote StartRead this user guide, including the Warnings section at the begin-ning. Ensure that the vehicle is parked in the open air and not in a garage. To use your remote start to pre-warm or pre-cool your vehicle, remember to set the climate controls to the desired settings before shutting off the engine.➤ Remote starting your vehiclePress the • A U X button on the remote control. The vehicle parking lights flash.On the 2-way remote, the Remote Start indicator appears and • ascending Remote Start tone plays.The preset remote start run time is 12 minutes. This can be changed to between 12 and 60 minutes (see your authorized dealer for program-ming changes).Your system has a feature (if programmed on) that will automatically notify you when the run time is running low. When 9 minutes (of the 12 minute default) runtime has elapsed, the system sends the 2-way remote control a paging signal. ➤ Points to rememberIf the hood is open or is the brake pedal is pressed, the vehicle will not start using remote start. The remote starter shuts down: When the brake pedal is pressed • The hood is opened •

Navigation menu