Voxx Electronics DEI7703 915MHz spread spectrum 25 channels User Manual hub

DEI Headquarters, Inc. 915MHz spread spectrum 25 channels hub

Contents

user manual hub

1© 2011 Directed Electronics. All rights reserved.User’s Guide6703A Lot Management System HubLogo, Directed Electronics w-driven.eps Logo, Directed with designed in USA.eps Logo, Directed with Distributed By.eps Directed Logo Usage Getting StartedConnect the hub to the designated computer* using the USB cable provided. The unit is powered via this cable which is also used for data exchange. Position the hub at the highest possible point in an area free of obstructions or interference. Rotate the antenna to the upright position.The hub is used to relay information between the 7703A keypad and the computer. When the hub is connected to power, it initializes by testing each display character in sequence before providing status feedback. Due to the display’s limited character capacity, system status is ab-breviated. These abbreviations are as follows:Display Description UN hub is unplugged, verification is offUN VO hub is unplugged, verification is onPA PC is active, verification is offPA VO PC is active, verification is onNR PC is not responding, verification is offNR VO PC is not responding, verification is on*This designated computer uses proprietary pre-loaded software which enables the hub to transfer data via this system to a remote database.FCC/ID NoticeThis device complies with Part 15 of the FCC Rules. Op-eration is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harm-ful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.• Reorient or relocate the receiving antenna• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a circuit dif-ferent from that to which the receiver is connectedAntennaDisplayMini-USBport
2© 2011 Directed Electronics. All rights reserved.• Consult the dealer or an experienced radio/TV tech-nician for helpAny changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Canada statements:This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ-ing interference that may cause undesired operation of the device.This radio transmitter 6703A & 7703A has been ap-proved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de li-cence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouil-lage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.Le présent émetteur radio 6703A et 7703A a été approu-vé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admis-sible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.When antenna is detachable and RSS-IC AppliesThis radio transmitter (identify the device by certification number, or model number if Category II) has been ap-proved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s’il fait partie du matériel de catégorie I) a été approuvé par In-dustrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont stricte-ment interdits pour l’exploitation de l’émetteur.Antenna S161XX-915RThe antenna used for the transmitter must be installed to provide a separation distance of at least 7.87 inches (20 cm) from all persons, and must not be co-located or oper-ating in conjunction with any other antenna or transmitter.L’antenne de l’émetteur doit être installé à une distance d’au moins 7,87 pouces (20 cm) de toutes les personnes, et ne doit pas être placé ou utilisé en conjonction avec toute autre antenne ou tout autre émetteur.This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Navigation menu