Voxware VLS410C352 Digitally Modulated Transmitter User Manual User Guide UPDATED

Voxware, Inc. Digitally Modulated Transmitter User Guide UPDATED

User Guide UPDATED

VLS-410 Technical Specifications Processor PXA255, 400 Mhz OS WinCE.NET Runtime Memory (SDRAM) 128Mbyte Storage Memory (Flash) 64Mbyte Battery Life >10 hrs Hardware Interface Ports 2 serial, USB Client Weight 22 ounces with battery Batch Mode (buffered results) Yes Radio Support WIFI 802.11b; Symbol 802.11 TTS (Text-to-Speech) Engine Cepstral, higher quality male voice Internal Card Support PCMCIA/CF,SD Power LED Status Green light will blink slowly (once every 3 seconds ) during a software upgrade Green light will blink normal (once a second) once the browser is started. Green light will remain solid for 30 seconds or so when unit is booted up. Red light will blink fast if the unit has an error during the system install. No lights are normal when the unit runs out of battery or suspends. Alternate Red and Green blinking lights (once a second) is normal when the unit is out of range. Battery Change Procedures 1. Press & release the SUSPEND/RESUME button. 2. WAIT for the power light to go out (approximately 1.5 seconds). 3. Press the battery release button and lift out the battery pack. 4. Take a fully charged battery pack from the battery charger. 5. Press down firmly on the battery pack until you hear a small click. NOTE: After suspending the device and removing the battery, if a new battery is not inserted within 7 minutes then the unit will RESET when the battery is inserted. Caution! Changes and modifications not expressly approved by Voxware, Inc. could void the user’s authority to operate the equipment. This product must be professionally installed. Approved Accessories The accessories listed below are approved for use with the VLS-410 and the use of any other accessories is prohibited. Metrologic Bar Code Scanner Model # IS 4220 Available with Voxware compatible cable from Accucode +1-303-639-6111 VLS Pouch Available from Voxware VLS Headset Available from Voxware Battery Pack Suspend/ Resume button & Power LED Reset button Battery Release button
Suspending the Unit To SUSPEND the unit do the following: 1. Press & release the SUSPEND/RESUME button. The power light will go out in 1.5 seconds. Warning! Holding down the SUSPEND/RESUME button for more than 8 seconds will RESET the VLS–410 device. To RESUME the unit (after suspending it) just press & release the SUSPEND/RESUME button again. Notes: The VLS-410 unit will automatically go into Suspend mode when the battery charge is below 5%. In this instance, the battery will remain in Suspend mode for up to 2 days, if not removed sooner. VLS-410 Software Update Messages On occasion your device will need to be updated with new software/files. When this occurs you will hear one of the following messages: Resetting the Unit Method 1: 1. Remove the battery (while the unit is On). 2. Wait for the power light to go out (approx. 1.5 seconds). 3. Put the battery back on again. Method 2: 1. Press for more than 8 seconds the SUSPEND/RESUME button. Method 3: Cold Hardware Reset. 1. Press & release the SUSPEND/RESUME button. 2. Wait for the power light to go out (approx. 1.5 seconds). 3. Press the RESET button. A cold hardware reset of the unit is performed. Warning! Pressing the RESET button when the unit is ON may cause a loss of data. Version 7 9/16/04 Voxware VoiceLogistics® VLS-410 Tech Specs & Usage Procedures Regulatory Information This equipment is within SAR (specific absorptionrate) limits for a portable device in contact with thebody. The maximum SAR measurement inVoxware’s supplied pouch is 0.011W/kg Body. Industry Canada: This device has been designed tooperate with an antenna having a maximum gain of 0dB. An antenna having a higher gain is strictlyprohibited per regulations of Industry Canada. Therequired antenna impedance is 50 Ohms. To reducepotential interference to other users, the antennatype and its gain should be so chosen so that theequivalent isotropically radiated power (EIRP) is notmore than that required for successfulcommunication. Message Software Type Installing new application version Application Updating Browser files Browser Updating Shell files Shell Installing new system version System Build Updating TTS files TTS

Navigation menu