Vieworks WLE900VXVW 802.11ac Dual Band Module User Manual

Vieworks Co., Ltd. 802.11ac Dual Band Module

User Manual

WLE900VX 7AA000S-VW Instruction manual
1 1. KEY FEATURES • Qualcomm Atheros QCA9880 • XB140 Reference Design • 2.4GHz max 21dBm & 5GHz max 20dBm output power (per chain) • IEEE 802.11ac compliant & backward compatible with 802.11a/b/g/n • 3x3 MIMO Technology, up to 1.3Gbps • MiniPCI Express 1.1 interface • Supports Spatial Multiplexing, Cyclic-Delay Diversity (CDD), Low-Density Parity Check (LDPC) Codes, Maximal Ratio Combining (MRC), Space Time Block Code (STBC) • Supports IEEE 802.11d, e, h, i, k, r, v time stamp, and w standards • Supports Dynamic Frequency Selection (DFS) • Cards are individually calibrated for Quality Assurance • Supported by either CompexWRT with Atheros Reference Wireless Driver OR OpenWRT with ath10k Wireless Driver on WPJ344
2 2. Specifications Chipset QCA9880 Host Interface MiniPCI-Express 1.1 Standard Operating Voltage 3.3V DC Antenna Connector 3 x U.FL Frequency Range 2.412 ~ 2.472 GHz 5.180 ~ 5.825 GHz Power Consumption 5W (Max) Modulation Techniques OFDM: BPSK, QPSK, DBPSK, DQPSK, CCK, 16-QAM, 64-QAM, 256-QAM Temperature Range Operating: -20ºC to 70ºC Storage: -40ºC to 90ºC Humidity Operating: 5% to 95% (non-condensing) Storage: Max. 90% (non-condensing) Dimensions (H x W x D) 50.95 x 30 x 3.2 mm ▶PCB Dual-Band Antenna (Specifications) Electrical Specifications MODEL VWi-2450/5500DP-C1.32 [A/B/C] Frequency Range [GHz] 2.4~2.5 / 5.1~5.9 V.S.W.R ≤ 1 : 5.0 Gain[dBi] - 2.4 GHz > 0 dBi Gain[dBi] – 5 GHz > -2 dBi Input Power 5 [W] Input Impedance 50 [Ω] Polarization Isotropic Mechanical Specifications Type PCB Radiation Type Dipole PCB Connector Type U.FL (Gold-Plating)
3 3. Connector Map Main connectors CH0, CH1, CH2 Mini PCI-e 1.1
4 4. Dimensions
5 5. Description of module assembly Put the WLE900VX 7AA000S-VW module into the module slot. Secure the mudle with the screws below the module.
6 6. Statements Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must
7 accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains FCC ID: PFRWLE900VXVW". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement This Class B digital apparatus complies with Canadian ICES-003. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This radio transmitter (identify the device by certification number or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. IMPORTANT NOTE: IC Radiation Exposure Statement This device is in compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and has been tested in accordance with the measurement methods and procedures specified in IEEE 1528. This equipment should be installed and operated with a minimum separation distance of 20 cm between the device and your body.
8 The device and its antenna must not be co-located or operated in conjunction with any other antenna or transmitter. This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the IC RSS-102 radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. USERS MANUAL OF THE END PRODUCT: Instruction to OEM This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This application and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements. Host labeling requirement: “Contains transmitter module FCC ID: PFRWLE900VXVW IC : 11233A-WLE900VXVW This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. French statement: Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) l’appareil ne doit pas produire de brouillage; 2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
9 Vieworks Co., Ltd. 41-3, Burim-ro 170beon-gil, Dongan-gu, Anyang-si, Gyeounggi-do, 14055 Republic of KOREA

Navigation menu