Venture Global PB-SDX Wireless transmitter User Manual 2

Venture Global Limited Wireless transmitter 2

Users Manual

Step 1: Insert battery to the transmitter to be used.Step 2: Insert batteries to the receiver to be used (chime unit).Step 3: Enter pairing mode for receiver (chime unit). Press and hold the zone Select button for 3 seconds. The LED #1 will flash.Step 4: Press the button again to move to the zone you wish to pair with. Press melody selector to scroll through the melodies. Once you hear your preferred melody, do not press again as it is now selected. Step 5: Once the zone and melody are selected, press the test button on the transmitter once to pair. If successful, the receiver (chime) will generate a short tone. Press the button to exit pairing mode, the system is ready to use. USER MANUALParts & FunctionTest Button/LED IndicatorWiring HoleCable ductWiring hole coverConnection wireBattery compartmentWire SocketCoverPowerThis unit using a long life battery CR123A.1. Open the front cover using a small flat screw driver2. Take out the connection wire in the battery compartment.3. Install a CR123A battery to the battery compartmentInstallationTake away the wire hole cover Insert the cable duct to the basePlug the connection wire to the wire socketPlace the wires in the cable ductand replace the cable duct coverMark the mounting holeson the celling using a pencilclose to the alarm device.o/ 7mm25mmRequires an electric drill for holes to fix the transmitter with the provided ram plug and screws.Mount the transmitter beside thealarm device with the screws provided.Connect the two connection wires to theoutput of alarm device according to theuser manual of the alarm device.Red connected to '+'Black connected to '-'Double-sided adhesive tapeCODE PAIRING & MELODY SELECTIONIDZone select buttonMelody selector buttonCHIMELIGHTLIGHT & CHIMETo stop the Chime whilst it is alerting press the reset buttonTest the transmitterTo test the transmitter, press the test button once. the LED indicator will lit and will send a trigger signal to the receiver.Recommended test the transmitter once a monthBattery low indicationOnce the transmitter unit detect battery voltage is low, the LED indicator will blink every 10 second. If the transmitter is activated, The battery low information will be sent to the receiver for display. Code ConflictIf the transmitter coding is the same as another transmitter you must change the code. When you have changed the code re-pair the transmitter is needed. Open the coverRemove the batteryPress and hold the test button, insert the battery whilst holding the button for 5 seconds. The LED will flash 5 times when a new code is generatedTest the connectionTo test the connection between the transmitter and smoke alarm, press the test button on the smoke alarm. the LED indicator on the transmitter will lit and will send a trigger signal to the receiver.1000-6381324Remark:This relay transmitter can work any devices with 3 to 9V output relay terminal. Assume to connect with alarm device has built-in output terminal with 3 to 9 volt output when the alarm device is activated. RedBlack+-Connection wire needs correct with right polarity, wrong connection will cause the transmitter does not work.Alarm deviceTransmitterBattery installationR&TTEFCC Statement:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Modifications to this product will void the user's authority to operate this equipment.

Navigation menu