Venture Global DWA-800 Driveway Alert Receiver User Manual 2

Venture Global Limited Driveway Alert Receiver 2

User Manual

USER MANUALKey Function On ReceiverPower On/Off DC jackVolumeIndications on Receiver* AC Power Operate: Light up blur LED while using AC adaptor* Back up Battery Operate: Light red LED while operated by battery* RX Battery Low: Flashs red LED with 0.3 sec. On / 5 sec. Off and sounds "beep" every half minute* Remote Sensor Battery low: Flash red LED with 0.3 sec. On / 5 sec. Off and sound "beep"AC Power on/RX Batt. Low #1 Zone/ Sensor#2 Zone/ Sensor#3 Zone/ SensorRemote sensorbattery low#4 Zone/ Learn/NextMelody/Batt.ChkPause/ResetCable come out from RelayBattery CoverPower on/off : To switch on or switch off the receiver using this switch.Volume: To adjust the volume level by rotating volume DC jack: The AC/DC adaptor plug to this jackPause/Reset: Pause - Temporarily stop the receiver bypress and hold this button 3 sec. Reset - Clear the sound and light on the receiver by press this button onceMelody / Batt. chk: See the chapter of learn and Check which sensor in battery low Learn/Next: See the chapter of learn and Check which sensor in battery lowBottom on ReceiverRemove the battery cover for setting the connection / time delay.12V outNONCCOM+ -Pause Time SettingPause mode12V output control1 S 5 S 10 S 60 SDelay time settingNO/NC control30 minUS60 minOff OnEUABCDEFA Output terminal: Connect to the device that you wanted control, such as Gate opener, Door release or external alarm speaker ..... --- : this terminal output 12v 300mA when the select zone has been 12V out trigger. (This terminal can not output 12V when using the backup battery.) This output cooperate with "E". you can select which zone relayed to this output by slide the DIP witch 1,2,3,4 on or off. --- NO (Normal Open): this terminal output short circuit when the select zone has been trigger. --- NC (Normal Close): this terminal output open circuit when the select zone has been trigger. The NO and NS outputs cooperate with "F". you can select which zone relayed to these output by slide the DIP witch 1,2,3,4 on or off.B. Pause timer setting: Select the pause time 30 min or 60 min C. Pause mode: EU mode: auto turn on when the pause time is over. US mode: the receiver generat a beep tone when the pause time is over. D. Delay time setting: These switch adjust the output time of the output terminal. E. 12V output control: To choose which zone connect to the 12V output.F. NC/NO output control: To choose which zone connect to NO/NC output. Power & SettingAAAAAAInstall the 4 AAA batteries into the battery compartmentas the indication on the compartment Although this receiver operate with AC/DC adaptor, we still need to install battery for backup.AASlide to open the battery coverReplace the battery coverAdjust the dip switch as you need andConnect the wire to the device that youwant to control The main power of this unit is 12V/500mA AC/DC adaptorFCC Statement:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Modifications to this product will void the user's authority to operate this equipment.Sensor
Switch inside the transmitterSensitivityFilterPhoto sensor On/OffTest Button12m1-2m/sec 0.5-1m/sec8m 7m 4m7 sec 30 secAfter detect an intrude the sensor will sleep 7 seconds or 30 seconds. Battery Installation Interval TimerBattery compartmentAAAAAAAAInstall the 4 AA batteries into the battery compartmentas the indication on the compartment Replace the cover and lock screw Replace the sun blockerInstallationMount the transmitter on the wall 1.5m from the ground and slightly toward the ground andpoint to the target sensing area. Mark the 4 hole on the wall using a pencil.o/ 7mm 25mmRequires an electric drill for holes to fix the Sensor with the provided ram plug and screws.Adjust the sensor to make a good operation angleRemove the screw from the top cabinet.OnOff
AC Power on (Blue)/RX Batt. Low (Red)Remote sensorbattery lowLearn (Pairing with remote sensor)1. Press "learn" button and hold 3 second to entering to "learn mode"2. Press "learn" button to select the preferred zone3. After select the zone then press "melody" button to select the preferred melody for the sensor going to be paired4. Trigger the sensor which going to be paired. * Sounds "Beep" whiled sussfully * If the Sensor paired with other Zone: there will not sound and show the Zone paired with the sensor for 3 sec., Then goes back to the selected Zone. * If all the space were occupied. 1,2,3,4 zone's LED flash 3 time.Melody select sequenceMelody#1 >> Melody#2>> ....>>Melody#32 >> Melody#1How to Pause the systemClean all the sensor in a zone1. Press "Learn: button and hold 3 second to enter "learn mode"2. Press "next button" to select which zone going to unpair the sensors.3. Press "Pause/Reset" button for 3 sec. To unpair all the sensors in the zone.4. Press "Next button" untill exit the mode.Check which sensor in battery lowBattery low1. Press "Battery Check" button and hold 3 second to entering to 2. Press "Next button" button to switch between the zones, light up Zone 1 first, Press again the "Next button" to switch zone 2 > zone 3 > zone4If going to chk, zone 2.Press 2 time "next button"make the LED stop at Zone2Press and hold "battery chk" buttonThe LED 1,2,3,4 will show whichsensor/sensors are battery low.* Release "battery chk" button and press "Next" to check next zone.* zone 1 >> zone 2 >> zone 3 >> zone 4 >> exit the battery modeHow to clearn the battery low signalBATT. LOW alert will not off until replace the battery.Code ConflictIf the PIR sensor coding is the same as another transmitter you must change the code. When you have changed the code, you need to re-pair the PIR sensor.AAAAAAAAPress and hold the test button, insert the battery and hold the button 5 seconds. The LED will flash 5 time when a new code is generated2. Press "Pause" button and hold 3 second and release while the four zone LED lit.3. The four zone LED will lit up in succession to indicate the receiver is in pause mode.4. Press the pause button again to exit the pause mode.The receiver will not receive any signal while the receiver is in pause modePause mode: EU mode: auto turn on (Exit the pause mode) when the pause time is over.US mode: the receiver generat a beep tone when the pause time is over.Press the pause button to exit the pause modeIf you want to disable the system Temporary:1. Choose the pause time (30 or 60 minutes)"check mode". The sensor battery low LED will light up afterenter the battery check mode.ReceiverSensorsThe " RX Batt. Low" LED (Red) will blink every 5 second and beep every 15 minute to indicate the backup batter low or no battery installedThe " Remote sensor battery Low" LED will blink every 5 second and beep every 30 minute to indicates sensor(s) batter low.BatteryLowIndicationPower IndicationACPower Battery NormalBattery Low LED Indication Beepsound every30 minutesBlueRedBlue + Red FlashBlue + Red Flash Red FlashNoBatteryinstalled

Navigation menu