VTech Telecommunications 80-6684-00 1.9GHZ CORDLESS PHONE (BASE WITH BLUETOOTH) User Manual

VTech Telecommunications Ltd 1.9GHZ CORDLESS PHONE (BASE WITH BLUETOOTH)

UserManual.wiki >

VTech Telecommunications >

80-6684-00 User Manual >

Contents

User Manual

User’s manual TL92278/TL92378/TL92328 DECT 6.0 cordless answering system with Bluetooth®wireless technology

Please read and follow these instructions carefully:• Use only the supplied rechargeable battery or replacement battery.• Observe the proper polarity orientation between the battery and handset during battery installation.• Do not dispose of the battery in a fire. Check with local codes for special disposal instructions.• Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.• Exercise care in handling batteries in order not to create a short circuit with conductive materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause harm.• Charge the supplied battery or replacement battery with this product only in accordance with the instructions and limitations specified in this manual.• Do not disassemble your telephone. There are no user- serviceable parts inside. Refer to qualified service personnel for servicing.Before you beginyou must install and charge the battery, see page XX for Battery installation instructions.3

Your telephone contains the following items. Telephone baseBattery for cordless handset(2 for TL92278)(3 for TL92378/ TL92328)Cordless handset(2 for TL92278)(3 for TL92378/ TL92328)Charger for cordless handset with power adapter installed(1 for TL92278)(2 for TL92378/ TL92328)Battery compartment cover(2 for TL92278)(3 for TL92378/ TL92328)User's manual Quick start guideUser’s manual TL92278/TL92378/TL92328 5.8 GHz digital cordless answering system with BLUETOOTH®wireless technologyQuick start guideTL92278/TL92378/TL92328 5.8 GHz digital cordless answering system with BLUETOOTH®wireless technologyParts checklistWall mount bracket Telephone line cord

5User’s manual TL92278/TL92378/TL92328 DECT 6.0 cordless answering system with Bluetooth®wireless technologyGetting startedQuick reference guide handsethandset ............................................ 3 telephone base ............................ 4Handset status icon ......................... 6Installation setup ............................... 5Telephone base installation ......... 6Charger installation .......................... 9Battery installation & charging .........................................10Installation options ...............................10Expansion handset ...............................15Adding & registering handsets .....16Replacing a handsetBluetoothIntroducing Bluetooth ...................19Glossary of terms ............................20Bluetooth setup ...............................21Handset settingsHandset main menu .......................22Handset settings ..............................16Telephone operationHandset operation ..........................28Options while on calls ..................34Chain dialing ......................................37 Intercom ...............................................38Call transfer using intercom ......40DirectoryAbout the directory ........................31Creating directory entries ...........32Directory review ...............................34 Directory search ...............................35To dial, delete or edit entries .....................................36Caller IDCaller ID operation ..........................37To review the caller ID history ..............................................40Answering systemAbout the answering system.....41Day & time announcement .........42Answering system mode .............44Outgoing announcements ..........45 Answering system setup ..............47Message playback ...........................51Recording & playing memos ......52Message counter displays ...........53Remote access ..................................54Table of contents

Appendix A, Alert tones and lights ...................70Appendix B, Handset display screen messages ................................................71Appendix C, Maintenance.......................................74Appendix D, Important safety information ....75Appendix E, FCC Part 68 and ACTA..................78Appendix F, FCC Part 15 ........................................80Appendix G, Limited warranty .........................81Appendix H, Technical specifications ...............71Appendix I, Troubleshooting ..........................72Index ...................................................80Table of contents

1Getting startedMENU/SELECTPress to display the menu. While in the menu, press to select an item or save an entry or setting.Quick reference guide - handsetDELETE/MUTEDuring a call, press to mute microphone (page 25). While reviewing the caller ID history, press to delete an individual entry, or press and hold to clear the caller ID history (page 40). While predialing, press to delete digits (page 21).REDIAL/PAUSEPress to view redial memory (page 22). While entering numbers, press and hold to insert a dialing pause (page 32).SPEAKERPress to turn on the handset speakerphone. Press again to resume normal handset use (page 21).HOME/FLASHPress to make or answer a HOME call.Flashes rapidly when there is rapidly when there is an incoming HOME call. Flashes slowly when a HOME call is on hold.During a HOME call, press to receive an incoming call if call waiting is activated (page 57). CELLULARPress to make or answer a CELLULAR call.Flashes rapidly when there is an incoming CELLULAR call.Flashes slowly when a CELLULAR call is on hold.During a CELLULAR call, press to receive an incoming call if call waiting is activated (page 57).OFF/CLEARDuring a HOME or CELLULAR line call, press to end the call.While in a menu, press to cancel an operation, back up to the previous menu, or exit the menu display.CHARGE indicatorOn when the handset is charging in the telephone base or charger. DIR / CID Press DIR to display directory entries (page 34). Press to scroll up while in menus. While entering names or numbers, press to move the cursor to the right. Press to increase the listening volume when on a call.Press CID to display caller ID history (page 40). Press to scroll down while in menus. While entering names or numbers, press to move the cursor to the left.Press to decrease the listening volume when on a call.HOLDPress to put the HOME or CELLULAR call on hold.

2Getting startedFeature menuMenuFeature menuDIRECTORY (page 34)CALL LOG (page 40)INTERCOM (page XX)RINGER VOLUME (page 16)RINGER TONE (page 17)KEY TONE (page 17)LANGUAGE (page 18)CLR VOICE MAIL (page 19)HOME AREA CODE (page XX) Using menusPress or to scroll through menu items.Press MENU/SELECT to select or save changes to a highlighted menu item.Press OFF/CLEAR to cancel an operation, back up to the previous menu, or exit the menu display.The > symbol shows a highlighted menu item.>DIRECTORYCALL LOGQuick reference guide - handset

3Getting startedIN USE indicatorOn when the handset is in use, when the answering system is answering an incoming call or when you are registering a handset.Flashes when another telephone is in use on the same line, or you are deregistering handset(s) from the telephone base.Flashes quickly when there is an incoming call. •••Quick reference guide - telephone base VOICEMAIL indicatorFlashes when you have new voicemail. Voicemail is a service offered by your local telephone company, and is different from answering system messages (page 19). SETUPPress to hear and change setup options (page 47).MESSAGE COUNTERNumber of messages (or during playback, message number currently playing).CLOCKPress to review or set the clock (page 42).X/DELETEPress to delete the message currently playing. Press twice to delete all old messages when the phone is not in use (page 51)./REPEATPress to repeat a message. Press twice to play the previous message (page 51). PLAY/STOPPress to start or stop message playback (page 51).ANNC.Press to review or record the outgoing announcement. Press again to end announcement playback or recording (page 45).RECORDPress to record a memo (page 52) or, after pressing ANNC to record an outgoing announcement (page 45)./SKIPPress to skip a message (page 51).HANDSET LOCATORPress to make handsets beep so you can locate them (page 23). ANSWER ONPress to turn the answering system on or off (page 44). BLUETOOTHPress to enable the Bluetooth feature on the telephone base. On when the telephone base is paired and connected with a cellular phone. Flashes when the telephone base is paired but not connected with a cellular phone. Answering System Functions

4Getting startedHOME line - on steady when the HOME line is in use. CELLULAR line - on steady when the CELLULAR line is in use. BLUETOOTH - on steady when a cellular phone is connected with the telephone base. NEW VOICE MAIL - new voicemail received from the local telephone company. SPEAKERPHONE - the speakerphone is in use. Ringer off - the handset ringer is turned off. Battery status - battery is charging (animated display). Battery status - low battery (flashing); place handset in telephone base or charger to recharge. MUTE Microphone is muted.NEW Missed and unreviewed calls.Handset status iconsHANDSET 110:21 AM 11/23 25 MISSED CALLS NEWMUTE

Getting startedInstallation setup5Install the telephone base close to a telephone jack and a power outlet not controlled by a wall switch. The telephone base can be placed on a flat surface or vertically mounted on the wall (see page 10). For optimum range and better reception, place the telephone base in a central and open location.Depending on the environmental conditions, make sure that your Bluetooth enabled cellular phone is within 12 feet of where you install the telephone base in order to maintain a reliable connection between your Bluetooth cell phone, telephone base, and cell tower.If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack (see the following page). The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters.Your product may be shipped with a protective sticker covering the handset or telephone base display - remove it before use.For customer service or product information, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.Avoid placing the telephone base too close to:• Communication devices such as: television sets, VCRs, or other cordless telephones.• Excessive heat sources.• Noise sources such as a window with traffic outside, motors, microwave ovens, refrigerators, or fluorescent lighting.• Excessive dust sources such as a workshop or garage.• Excessive moisture.• Extremely low temperature.• Mechanical vibration or shock such as on top of the washing machine or work bench.STOP! See page 8for easy instructions.You must install and charge the handset battery before using the cordless handset.

6Getting startedTelephone base installationInstall the telephone base as shown below. Make sure that the electrical outlet is not controlled by a wall switch. If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack. The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters.The telephone base is set for desktop use. If you want to change to wallIf you want to change to wall mounting position, you will need to install the provided bracket to the telephone base, see page 10 for details.6. Raise the antenna.1. Plug one end of the telephone line cord into the telephone jack at the bottom of the telephone base (if necessary). 3. Route cords through slots. Power adapter DSL filter (not included), required if you have DSL high-speed Internet service.Telephone line cord2. Plug the small end of the power adapter into the power jack at the bottom of the telephone base. 4. Plug the other end of the telephone line cord into a telephone jack. 5. Plug the large end of the power adapter into a power outlet not controlled by a wall switch.

7Getting startedIMPORTANT INFORMATIONUse only the power adapter(s) supplied with this product. To order a replacement power adapter, visit our website at www.telephones.att.com, or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.1.2.Plug the power adapter into an electrical outlet not controlled by a wall switch.�harger installation

8Getting startedBattery installation & chargingInstall the battery as shown below. After installing the battery, you can make and receive short calls, but replace the handset in the telephone base or charger when not in use. For optimal performance, charge the handset battery for at least 16 hours before use. When fully charged, the handset battery provides approximately five hours of talk time or three days of standby time.Step 1Plug the battery securely into the connector inside the handset battery compartment, matching the color-coded label. Insert the supplied battery with the label THIS SIDE UP facing up as indicated. Step 2Step 3Press the depression and slide the battery compartment cover downwards (if necessary).Align the cover flat against the battery compartment cover, then slide it upwards until it clicks into place.Charge the handset by placing it face up in the telephone base or charger. The CHARGE light will be on when charging.Step 4IMPORTANT INFORMATIONUse only the supplied rechargeable battery or replacement battery (model BT8001). To order, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

9Getting startedInstallation optionsThe telephone base is set for desktop use. It is possible to change to wall mounting position by installing the bracket provided. Wall mounting requires a telephone outlet wall mounting plate with mounting studs that may require professional installation. You can purchase the mounting plate from many hardware or consumer electronics retailers. Desktop to wall mount installationTo change the telephone base to the wall mount position, make sure that you first unplug the telephone line cord and power adapter cord from the wall outlets before you begin. 2. Push down the telephone base until it clicks into the catches on both sides of the bracket. 1. Position the telephone base as shown below, and insert the extended tabs of the bracket into the slots under the telephone base.

10Getting startedInstallation optionsDesktop to wall mount installation4. Align the holes on the bracket with the standard wall plate and slide the bracket until the telephone is secured as shown below. Plug the telephone line cord into a telephone wall jack. Plug the power adapter into an power outlet not controlled by a wall switch. 3. Bundle the telephone line cord and power adapter cord, and secure them withBundle the telephone line cord and power adapter cord, and secure them with a twist tie before placing them behind the telephone base as shown below.

11Getting started5. Make sure the telephone is securely positioned as shown below.Installation optionsDesktop to wall mount installation

12Getting startedInstallation optionsWall mount to desktop installation To change the telephone base to the desktop position, make sure that you firstmake sure that you first unplug the telephone line cord and power adapter cord from the wall outlets before you begin. 1. Remove the telephone base from the wall and untie the bundled telephoneuntie the bundled telephone line cord and power adapter cord. 2. Press on the catches on both sides of the bracket (indicated by arrows below) to unlock the telephone base from the bracket. 3. Pull the telephone base up to detach it from the bracket.The catch on the side of the telephone base.

Navigation menu