VIEWPAKER TECHNOLOGY E270HMG ALL-IN-ONE Monitor User Manual

SHENZHEN VIEWPAKER TECHNOLOGY., LTD ALL-IN-ONE Monitor Users Manual

User manual

：： ：、，。。：/70G23III. Mount the independent graphics card (not applicable for models with integrated graphic cards)1. Insert the independent graphics card into the PC sloton the PC main-board and attach the independent graphics card onto the graphics card bracket with a PWM3*8 screw.IV. Install the CD-ROM (built-in SATA notebookdrive)1. First use a knife to cut the connecting rubber and remove the burrs at the six positions marked with an arrow in the figure.2 .Fix the CD-ROM bracket on the drive with the PM2x5screws.3. Insert the DVD assembly into the DVD slot on themiddle cover and fix it with PWB3x8 screws.V. Mount the HHD1. Fix the HHD bracket with a dampingring onto the HHD with hex step screws in the right direction.2. Align the HHD assembly with the screwholes for the HHD and fix it with screws.Product ViewMicrophoneCameraPowerPilotLam HHD Pilot LampFunction KeyON/OFIncrease BrightnessReduce BrightnessRestartCD-ROM1Requirements of pollution control markings on China electronic informationproductsIn order to control and reduce the environmental pollution caused by the wastes of electronic informationproducts, promote the production and sales of low-pollution electronic information products, and protect theenvironment and human health, only toxic and hazardous substances contained by the products are given belowaccording to the Regulations of the Chinese Government for Electronic Information Products Pollution Control:Part nameUpper and lower coversMachine engine (aluminum or aluminum-magnesium alloys)LensPlastic assembliesMetal parts (SECC/SPTE/SPCC)Springs(SUS/SUP)Spring sheet (fast cut phosphor bronze)Rubber assembliesFan assembliesBase board assemblyCable and wirePower cordPower socket assembliesMetal and plastic bracket frameworksLabel/Name PlateCD/ManualMylarToxic and hazardous substances or elementsLead (Pb) Hg Cd ChromiumVI (Cr(Vl) PBB PBDE: It means that the content of this hazardous substance in all homogeneous materials of the part is lower than thelimit value stipulated in SJ/T11363-2006.X: It means that the content of this hazardous substance in at least one homogeneous material of the component isreater than the limit value stipulated in SJ/T11363-2006 Electronic Information Product.Duration of service of the electronic information products under normal use conditions described inthe manual shall be 10 years, which includes no leakage of toxic and harmful substances that would cause environmental pollution or harm to human body and property.Description of environmental service durationThe product is only applicable within an area of 2000M.StatementThis is a Class A product. In a domestic environment, it may cause radio interference,in this case the user may be required to take practical measures against interference.Installation steps1. Remove the base and back cover1. Loosen the four screws on the baseand remove the base.2. Loosen the eight screws on the backcover and remove the back cover.II. Mount the motherboard (compatible with 240x240mm ATX and below MICROATX/ITX/MINIITX motherboards, compatible with 60mm or below coolingmodules.1. Mount the I/O board according tothe figure.2. Align the PC main-board with the screwson the motherboard and fix it with six PWM3x8 machine screws.ALL-IN-ONE MonitorUSER INSTALLATION MANUALChanges or modifications not expressly approved by the party responsible for compliance could void the user'sauthority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for helpFCC Warning Statement.

Navigation menu