VIA Technologies VESHPD01A1 Door Station User Manual QG SHP D01 with spec ENG pub

VIA Technologies, Inc. Door Station QG SHP D01 with spec ENG pub

User Manual

Quick Guide SHP-D01 Door Station 2. SHP-D01 Front/Side panel Product InformationProduct InformationProduct InformationProduct Information Model: Model: Model: Model: SHP-D01 Package Lists:Package Lists:Package Lists:Package Lists: -SHP-D01 door station X 1 -RS485 cable X 1 -DIO cable X 1 -M4 * 30mm screw X 3 -8mm brass pipe + spring X 1 -Quick Guide X 1 5. SHP-D01 Installation steps 1. Put brass pipe + spring on the embedded box, as indicated in the ○1. 2. Distance between bottom of the embedded box and the ground is 132 cm. Front panel and size Side panel and size ○1 132 cm RJ45 port RS485 port 3. SHP-D01 back panel mm mm mm mm DC-In power Adjustment of camera switch ring DI1 reserved reserved DI2 reserved reserved DO1 Open the door Connect NO Relay default status is On DO2 reserved reserved DO3 reserved reserved DIO pin definition DIO definition 4. Relay connection (use OMRON MY2-J Relay as an example) Green LED Red LED Green LED ON: normal operation Green LED flash: booting Red LED ON: ○1 Enable home or egress security ○2Anti-dismantle has been triggered ○3Security has been triggered ○4Force status has been triggered DIO port NoteNoteNoteNote:::: 1. This diagram is for reference only, please see DIO definition for actual connection. 2. Max. value of motion for DIO is 400mA. 3. DI can externally connect to spring switch and NC of the dry contact. If the same DI needs to use 2 or more spring switches, connect by series. 4. DI that externally connects to switch (eg, doorbell, emergency pressure deduction) and gas detector, can connect to NO. To use 2 or more devices, connect by series. 5. If DI2 of the door station is not connected to door detector, please short DI2 and DI2GND. 6. When DO connects to electric lock, power supply locks, interruption of power supply unlocks. 7. When DO connects to alarm, alarm connects to Relay NO, motion on Relay will enable the alarm. 1. SHP-D01 Specifications Item Description Camera 500 megapixel wide-angle color lens Brightness exposure LED Reader (RFID) Support 13.56MHz, ISO14443A standard Network Interface RJ-45 Network transmis-sion rate 10/100M Power DC-12V Power consump-tion <10W Operating tem-perature 0~40° Humidity 0~95%, non-condensing Alarm speaker Dry Contact switch black browRed Orange Yellow Green Bleu Purple Grey White Red black browPurple
For more information on this and other VIA products, please visit : www.viatech.com/en/ 6. SHP-D01 installation diagram 60 cm Distance between lens and subject 145 cm Height between lens and ground Angle of view 60° 179.6 cm 69.2 cm 110.4 cm 6. Put the front plaque and plate back. Fix the bottom with two M2 screws. M2 screw M2 screw NoteNoteNoteNote:::: 1. Be careful of the orientation during installation. 2. Please do not install any other device close to the door station, keep at least 10 cm of distance. Assistant Exposure light key lens RFID area (within rectangular area ) 4. Use M4 screw to fix the main part. 5. Distance between bottom of the door station and the ground is 131 cm. Please consider the thickness of the tile or marble. 131 cm 3. Remove two M2 screws from the bottom of the plaque. Take off the plate in order to separate the plaque and the main part. M2 screw M2 screw plate VIA Technologies, Inc.VIA Technologies, Inc.VIA Technologies, Inc.VIA Technologies, Inc. 1F, 531, Zhong-zheng Road, Xindian District, New Taipei City 231, Taiwan Tel: 886-2-2218-5452 Fax: 886-2-2218-5453 Copyright © 2015 VIA Technologies, Inc. All rights reserved. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause. CAUTION! To prevent shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified personnel.

Navigation menu