VALEO Telematik und Akustik V1140-100 GSM/GPRS/UMTS/HSDPA/HSUPA Module User Manual 08 user guide

Peiker acustic GmbH & Co. KG GSM/GPRS/UMTS/HSDPA/HSUPA Module 08 user guide

08 user guide

_______________________________________________________________________________________________________________ Seite 1 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe User manual LTE-NAD V1140-xxx Peiker product ID: 2189-140-xxx-00 (V1140-xxx) Revision: 0.10 Date: August 2014 Status: Draft
_______________________________________________________________________________________________________________ Seite 2 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe History: Date Revision Name Comment 15.09.2013 0.5 wlo Initial document 13.12.2013 0.6 phse Some additions to sections 2.1 and 3.3 Some corrections to section 2.2, Figure 4 updated 16.12.2013 0.7 phse Some additions to section 8 01.04.2014 0.8 phse Modifications/additions to section 8 17.06.2014 0.9 phse Updated Max Antenna Gain Values in section 8.3 24.06.2014 0.9.1 wlo Added FW update and WIN7 driver installation 31.07.2014 0.10 phse Added FCC labeling requirements of V1140-100 08.08.2014 0.11 phse Modifications/additions to sections 8.1, 8.1.1 and 8.2
_______________________________________________________________________________________________________________ Seite 3 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Content 1 Introduction .......................................................................................................................................... 5 1.1 Scope .................................................................................................................................................. 5 1.2 Audience ............................................................................................................................................ 5 1.3 Contact information, Support ......................................................................................................... 5 1.4 Related Documents .......................................................................................................................... 5 2 Overview ............................................................................................................................................... 6 2.1 Product Variants................................................................................................................................ 6 2.2 Features ............................................................................................................................................. 7 2.3 Approvals ........................................................................................................................................... 7 3 Overview ............................................................................................................................................... 8 3.1 HW Features ...................................................................................................................................... 8 3.2 Connectors ......................................................................................................................................... 8 3.2.1 Module Signal and RF Connectors .......................................................................................... 8 3.2.2 Ground and Heat Dissipation Connectors.............................................................................. 8 3.3 Main Interfaces ................................................................................................................................. 8 3.3.1 USB .............................................................................................................................................. 8 3.3.2 SIM Interface ............................................................................................................................. 9 3.3.3 Power on ..................................................................................................................................... 9 3.3.4 Reset ........................................................................................................................................... 9 3.3.5 GPIOs .......................................................................................................................................... 9 3.3.6 GSBIs ......................................................................................................................................... 10 3.3.7 Module Pin-out ......................................................................................................................... 11 3.4 Supply Voltage ................................................................................................................................ 15 3.5 Power Consumption ....................................................................................................................... 15 3.6 Transmitter ...................................................................................................................................... 16 3.7 Receiver ........................................................................................................................................... 16 3.8 Environmental Specification .......................................................................................................... 16 3.8.1 Temperature Range ................................................................................................................ 16 4 Evaluation Kit ..................................................................................................................................... 17 4.1 Overview ...................................................................................................................................... 17 4.2 Firmware Update ........................................................................................................................ 21 4.2.1 Identify Qualcomm Diagnostics Port Number ..................................................................... 21 4.2.2 Install and Run FW Executable ............................................................................................. 21 4.2.3 Known Issues ........................................................................................................................... 22 4.3 Windows 7 Driver Installation ................................................................................................... 23 4.3.1 Driver installation................................................................................................................. 23 4.3.2 Available interfaces ............................................................................................................. 23 4.3.3 AT Command interface and PPP Dial-up Modem connection ....................................... 23 4.3.4 RmNet NDIS connection as Network Interface Card ..................................................... 25 4.3.5 Diagnostics interface ........................................................................................................... 26 4.3.6 NMEA GNSS interface ......................................................................................................... 26 5 AT Command Set ............................................................................................................................... 26 6 Safety Recommendations according to EN60950-1 ..................................................................... 28 7 List of Acronyms ................................................................................................................................ 29
_______________________________________________________________________________________________________________ Seite 4 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 8 Regulatory Certifications .................................................................................................................. 30 8.1 USA (FCC) ........................................................................................................................................ 30
_______________________________________________________________________________________________________________ Seite 5 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 1 Introduction 1.1 Scope This document gives an overview about electrical, mechanical and functional detail of the peiker LTE-NAD v1140-xxx. 1.2 Audience Information to integrate the module in other applications. 1.3 Contact information, Support peiker acustic GmbH & Co KG Max-Planck Street 32 D-61381 Friedrichsdorf / Ts. Germany http://www.peiker.de info@peiker.de 1.4 Related Documents None.
_______________________________________________________________________________________________________________ Seite 6 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2 Overview 2.1 Product Variants The LTE-NAD is available in multiple product variants: Peiker product # Module configuration 2189-140-100-00 (V1140-100) LTE EU configuration 2189-140-101-00 (V1140-101) LTE North America configuration 2189-140-103-00 (V1140-103) 2G/3G EU/RoW configuration 2189-140-104-00 (V1140-104) LTE Asia Pacific configuration 2189-140-105-00 (V1140-105) 2G/3G North America configuration 2189-140-106-00 (V1140-106) 2G/3G China configuration All variants include Quad band GSM/GPRS/EDGE (850, 900, 1800, 1900 MHz) V1140-100 LTE Bands B3, B7, B20 WCDMA Bands FDD1, FDD8 V1140-101 LTE Bands B2, B4, B5, B17 WCDMA Bands FDD2, FDD5 V1140-103 LTE Bands No LTE support WCDMA Bands FDD1, FDD2, FDD5, FDD6, FDD8 V1140-104 LTE Bands B1, B3, B5, B7, B19 WCDMA Bands FDD1, FDD5, FDD6, FDD8 V1140-105 LTE Bands No LTE support WCDMA Bands FDD2, FDD5 V1140-106 LTE Bands No LTE support WCDMA Bands FDD1
_______________________________________________________________________________________________________________ Seite 7 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.2 Features Features - Same footprint and pin-out for all modules - Voice and data calls are supported in all modules - GSM (R99, GPRS and EDGE) for all modules - WCDMA (R99, R5 HSDPA, R6 HSUPA and R7 HSPA+) for all modules - WCDMA (R8 DC-HSPA+) for all modules except for V1140-101 and V1140-105 - LTE (Rel.9 Cat3 FDD) for LTE capable modules - DTM/eDTM - eCall inband modem - Standalone GPS, GLONASS, AGPS (MS-Assisted and MS-Based) Data rates - GSM: DL/UL – 14.4kbps / 14.4kbps GPRS: Multislot class 12, DL/UL – 85.6kbps / 42.8kbps EDGE: Multislot class 12, DL/UL – 236.8kbps / 118.4kbps - WCDMA: DL/UL up to 384kbps HSPA+: Category 24 in DL using 64 QAM and Dual-Cell; Up to 42 Mbps – Not supported by V1140-101 and V1140-105 Category 14 in DL using 64 QAM; Up to 21 Mbps Category 6 in UL using 16 QAM; Up to 5.76 Mbps - LTE-FDD Category 3: Up to 100 Mbps in DL, up to 50 Mbps in UL Power Classes - LTE: All supported bands, Power Class 3 - WCDMA: All supported bands, Power Class 3 - EDGE: 850 MHz / 900 MHz / 1800 MHz/ 1900MHz, Power Class E2 - GSM / GPRS: 850 MHz / 900MHz, Power Class 4 - GSM / GPRS: 1800 MHz / 1900MHz, Power Class 1 Dimension and Weight - Dimensions: 31mm x 46mm x 4mm - Weight < 10 grams 2.3 Approvals - R&TTE directive - CE, GCF - FCC, IC, PTCRB - AT&T
_______________________________________________________________________________________________________________ Seite 8 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3 Overview 3.1 HW Features - Qualcomm SoC (system on chip) o LTE capable modules V1140-100, V1140-101 and V1140-104 MDM9215 Baseband / PMIC8018 Power management / WTR1605L o Non-LTE modules V1140-103, V1140-105 and V1140-106 MDM8215 Baseband / PMIC8018 Power management / WTR1605 - Cortex A5 Core up to 550 MHz - 3 DSPs for modem and low power audio sub systems - RPM Resource and power manager - 2Gb NAND Flash x16, - 2Gb Low Power Mobile DDR SDRAM x32 - 19.2MHz clock reference - Dedicated heat sink in center area underneath the PCB - GPS/GLONASS operation, GPS antenna biasing and diagnostics 3.2 Connectors 3.2.1 Module Signal and RF Connectors The LTE-NAD has 172 signal pins (2xAA and 2xBB) connector pads with 1.0mm pitch. The signal pads are located close to the board edges. There are three antenna pads, each collocated by RF GND connectors - Main transmit and receive antenna – pin LGA_PRX_ANT - Diversity antenna for WCDMA respective MIMO antenna for LTE – pin LGA_DRX_ANT_IN - GNSS antenna for both GPS and GLONASS – pin LGA_GPS_DRX_ANT 3.2.2 Ground and Heat Dissipation Connectors To support the usage of module under complicated thermal conditions, there are a number of large grounded pads in the center of PCB. These pads are dedicated ground pads to transfer heat dissipation to a carrier board. This should be especially considered by customer designs. A reference design showing landing patterns and PCB stack-up is available on request. 3.3 Main Interfaces 3.3.1 USB The NAD has one USB2.0 OTG high speed (480MBit) compliant interface including the PHY. The IF consists of 5 signals:
_______________________________________________________________________________________________________________ Seite 9 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe - USB_D_P: USB Data Plus signal - USB_D_M: USB Data Minus signal - USB_ID: Master/Slave Configuration1 - USB_VBUS: USB Voltage Supply - VREG_USB3_3V075 USB Voltage Output A dynamic reconfiguration between USB-Host or USB-Device is not foreseen, the NAD can be configured to USB-Host or USB-Device by the insertion of a resistor on the USB_ID line. 3.3.2 SIM Interface The NADs SIM interface is compatible to 1.8V and 3V SIM Cards, the necessary voltage and level shifting is handle by LTE-NAD automatically. The IF consists of the following signals: VREG_USIM USIM_CLK USIM_DATA USIM_RESET The data speed on the SIM IF is up to 4 Mbps, so HW designers should take care of the length and routing of the SIM IF to prevent potential EMC problems. 3.3.3 Power on The signal PON_N is used switch on the NAD-Module. PON_N is pulled against VMAIN on the LTE-NAD internally. Due to this fact it is recommended to pull this input against GND using an open collector or open drain output only. 3.3.4 Reset EXT_RESIN_N is used to reset the LTE-NAD-Module, see table of LTE-NAD signal pins. There are further reset signals available, please check . RES_IN is pulled against VMAIN power on the LTE-NAD internally. Therefore, it is recommended to pull this input against GND using an open collector or open drain output only. 3.3.5 GPIOs 1 The LTE-NAD is configured in the slave mode. For other configuration of the USB – Interface please contact peiker acustic GmbH & Co.KG.
_______________________________________________________________________________________________________________ Seite 10 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe There are 51 GPIOs on the LTE-NAD module available. Most of them are part of the 5 GSBIs provided in next chapter. They are used for different interfaces (see Table 1 and the following chapters). For allocation of GPIOs/GSBIs to different configurations please contact peiker acustics GmbH & Co.KG GPIOs and GSBIs share the same output pins and may not available when used as GSBI configuration. The following GPIOs are not belonging to a GSBI bundle: GPIO 47, 72, 82, 25, 28, 26, 27, 84, 80, 21, 23, 22, 24, 20, 1, 78, 79, 85, 86, 69, 0, 77, 65, 61, 68, 51, 54, 73, 48, 49, 53. The following GPIOs are belonging to a GSBI bundle: GPIO 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 29, 30. 3.3.6 GSBIs Each GSBI (General Serial Bus Interface) consists of a bundle of 4 GPIOs. 5 GSBI are available. The reference voltage is of the GSBIs is 1.8V. Available signals on GSBI bundles at the board to board connector: - GSBI1: GSBI1_0, GSBI1_1, GSBI1_2, GSBI1_3 (GPIO_29, 30, 2, 3) - GSBI2: GSBI2_0, GSBI2_1, GSBI2_2, GSBI2_3 (GPIO_4, 5, 6, 7) - GSBI3: GSBI3_0, GSBI3_1, GSBI3_2, GSBI3_3 (GPIO_8, 9, 10, 11) - GSBI4: GSBI4_0, GSBI4_1, GSBI4_2, GSBI4_3 (GPIO_12, 13, 14, 15) - GSBI5: GSBI5_0, GSBI5_1, GSBI5_2, GSBI5_3 (GPIO_16, 17, 18, 19) For the standard configuration of the GSBIs see the following Fehler! Verweisquelle konnte nicht gefunden werden. 3.
_______________________________________________________________________________________________________________ Seite 11 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 1 V1140-xxx General Serial Bus Interface GSBI interface configuration 3.3.7 Module Pin-out Table 1 Module Pin-out PIN Signal Direction related to LTE-NAD Comment 1 GND Input Power Main ground connection, Corner pad 2 – 22 GND Input Power Main ground connection 23 GPIO47 Input WDOG_DISABLE 24 JTAG_TDI Input JTAG Interface 25 JTAG_TDO Output JTAG Interface 26 GPIO_72 IN/OUT 27 JTAGTMS Input JTAG Interface 28 JTAG_TRST_N Input JTAG Interface
_______________________________________________________________________________________________________________ Seite 12 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe PIN Signal Direction related to LTE-NAD Comment 29 JTAG_RTCK Output JTAG Interface 30 GND Input Power Main ground connection 31 JTAG_TCK Input JTAG Interface 32 JTAG_RESOUT_N Input JTAG Interface 33 GPIO82 Output NAD – Runnig, Controll signal 34 JTAG_PS_HOLD Input JTAG Interface 35 EXT_RESIN_N Input Input Reset for LTE-NAD module 36 GND Input Power Main ground connection 37 RESOUT_N Output Output Reset 38 GPIO29_ SDC2_CMD IN/OUT SD Card CMD 39 GPIO25_ SDC2_D0 IN/OUT SD Card Data 0 40 GPIO28_ SDC2_D3 IN/OUT SD Card Data 3 41 GPIO30_ SDC2_CLK Output SD Card Clock 42 GND Input Power Main ground connection 43 GPIO26_ SDC2_D1 IN/OUT SD Card Data 1 44 GPIO27_ SDC2_D2 IN/OUT SD Card Data 2 45 PM_GPIO4 IN/OUT 46 GPIO84 Output Reset of the Codec 47 GND Input Power Main ground connection 48 SDC1_CMD IN/OUT SD Card CMD 49 SDC1_DATA0 IN/OUT SD Card Data 0 50 SDC1_DATA3 IN/OUT SD Card Data 3 51 SDC1_CLK Output SD Card Clock 52 GPIO80_SDC1_DET_N IN/OUT 53 GND Input Power Main ground connection, Corner pad 54 SDC1_DATA2 IN/OUT SD Card Data 2 55 SDC1_DATA1 IN/OUT SD Card Data 1 56 GPIO21_ I2S_WS Output I²S - Word Select 57 GPIO23_ I2S_DOUT Output I²S – Data Output 58 GPIO22_ I2S_DIN Input I²S - Data Input 59 GPIO24_ I2S_MCLK Output I²S - Master Clock 60 GND Input Power Main ground connection 61 GPIO20_ I2S_CLK Output I²S - Clock 62 GPIO19_GSBI5_3 Output 2 – Pin – UART TXD 3 63 GPIO17_GSBI5_1 IN/OUT I²C – Serial Data 64 GPIO18_GSBI5_2 Input 2 – Pin – UART RXD 3 65 GPIO15_GSBI4_3 Output 4 – Pin – UART TXD 1 66 GND Input Power Main ground connection 67 USB_D_P IN/OUT High – Speed USB Device for communication 68 USB_D_M IN/OUT High – Speed USB Device for communication 69 GND Input Power Main ground connection 70 GPIO14_GSBI4_2 Input 4 – Pin – UART RXD 1
_______________________________________________________________________________________________________________ Seite 13 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe PIN Signal Direction related to LTE-NAD Comment 71 GPIO13_GSBI4_1 Input 4 – Pin – UART Clear To Send 1 72 GPIO16_GSBI5_0 Output I²C - Clock 73 USB_ID Input 74 GPIO12_GSBI4_0 Output 4 – Pin – UART Ready For Receive 1 75 GND Input Power Main ground connection 76 USB_VBUS Input High – Speed USB Device for communication 77 GPIO11_GSBI3_3 Output 2 – Pin – UART TXD 2 78 GPIO10_GSBI3_2 Input 2 – Pin – UART RXD 2 79 GPIO9_GSBI3_1 IN/OUT 80 GPIO8_GSBI3_0 IN/OUT 81 GPIO6_ UIM2_CLK IN/OUT 82 GND Input Power Main ground connection 83 GPIO2_ UIM1_CLK Output SIM Card - Clock 84 GPIO5_ UIM2_RST IN/OUT 85 GPIO7_ UIM2_DATA IN/OUT 86 GPIO4_ UIM2_DET IN/OUT 87 GND Input Power Main ground connection, Corner pad 88 HSIC_DATA IN/OUT Connection to Ethernet Controller 89 GND Input Power Main ground connection 90 HSIC_STROBE IN/OUT Connection to Ethernet Controller 91 GND Input Power Main ground connection 92 GPIO3_ UIM1_DATA Output SIM Card – Data 1 93 GPIO1_ UIM1_RST Output SIM Card – Reset 1 94 GPIO78 IN/OUT 95 GPIO79_ HSIC_RDY Output Reset of Ethernet Controller 96 GPIO85 Output Time synchronization 97 GPIO86_ GPS_EXT_LNA_EN IN/OUT 98 GND Input Power Main ground connection 99 VREG_USB3_3V075 Output Power Output Power to USB 100 GND Input Power Main ground connection 101 VREG_MSME_1V8 Output Power Output Power 102 GND Input Power Main ground connection 103 VREG_UIM2 Output Power Output Power to SIM Card 2 104 VREG_SDC1_2V95 Output Power Output Power to SD Card 1 105 GND Input Power Main ground connection 106 VREG_UIM1 Output Power Output Power to SIM Card 1 107 GND Input Power Main ground connection 108 GND Input Power Main ground connection 109 VMAIN Input Power Main power 110 VMAIN Input Power Main power 111 VMAIN Input Power Main power 112 VMAIN Input Power Main power
_______________________________________________________________________________________________________________ Seite 14 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe PIN Signal Direction related to LTE-NAD Comment 113 GND Input Power Main ground connection 114 GND Input Power Main ground connection 115 PON Input Power On 116 HW-REV-RESISTOR Output 117 PM_GPIO3 IN/OUT 118 GND Input Power Main ground connection 119 PM_MPP5 Input PM – ADC – channel 120 PM_MPP1 Input PM – ADC – channel 121 GND Input Power Main ground connection 122 GPIO69 Output Switch between main and back up antenna 123 GPIO0_ UIM1_DET Input SIM Card – Detection 1 124 GPIO77 Output Reset signal of SDC2 125 GPIO65 Output NAD – Wake up 126 GPIO61 Input NAD – Update 127 PON_N Input Power On 128 GND Input Power Main ground connection 129 GPIO68 Output PS-3V8-Hold 130 GPIO51 Input BOOT_CONFIG3 131 GPIO54 Input BOOT_CONFIG0 132 GND Input Power Main ground connection 133 PM_MPP2 Input PM – ADC - channel 134 PM_GPIO2 IN/OUT 135 PM_GPIO1 IN/OUT 136 PM_GPIO6 IN/OUT 137 GND Input Power Main ground connection 138 GPIO73 IN/OUT 139 GND Input Power Main ground connection, Corner pad 140 GPIO48 Input BOOT_CONFIG6 141 GPIO49 Input BOOT_CONFIG5 142 GPIO53 Input BOOT_CONFIG1 143 – 152 GND Input Power Main ground connection 153 LGA_PRX_ANT Connection to the antenna switch 154 – 160 GND Input Power Main ground connection 161 LGA_GPS_DRX_ANT Connection to the antenna connector 162 – 164 GND Input Power Main ground connection 165 LGA_DRX_ANT_IN Input Connection to the antenna switch 166 LGA_DRX_ANT_OUT 167 – 172 GND Input Power Main ground connection
_______________________________________________________________________________________________________________ Seite 15 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Note: Pins should be grounded when not used in design. 3.4 Supply Voltage The external supply voltage is applied to LTE-NAD by 8 Pins on modules signal connectors. PINs 109, 110, 111, 112 for VMAIN PINs 107, 108, 113, 114 for the corresponding GND Please note that there are further main ground connection that should be connected to ensure proper NAD function. TA = -40°C … +85°C Absolute minimum/maximum supply voltages 3.6V ~ 4.0V Nominal supply voltage 3.8V Recommended supply voltage 3.8V Voltage drop @ GSM power burst (33dBm) <100mV During Hi RF Power GSM bursts the power amplifier can draw peak currents > 2Amps at VMAIN. The voltage drop during the GSM burst shall not exceed 100mV. 3.5 Power Consumption TA = +25°C, VPH_PWR =3.8V Output Power Output Power max. (typ. 23dBm) 0 dBm Voice call WCDMA BC1 ~530mA ~145mA Voice call WCDMA BC2 ~570mA ~145mA Voice call WCDMA BC5 ~630mA ~140mA Voice call WCDMA BC8 ~580mA ~140mA PCL 5 (typ. 32.5 dBm) PCL 19 (typ. 5dBm) Voice call GSM850 ~260mA ~65mA Voice call GSM900 ~270mA ~65mA PCL 0 (typ.30.5dBm) PCL 15 (typ.0dBm) Voice call GSM1800 ~165mA ~65mA Voice call GSM1900 ~165mA ~65mA Standby current GSM DRX = 5 Tbd mA Standby current WCDMA DRX = 7 Tbd mA Standby current LTE DRX = 7
_______________________________________________________________________________________________________________ Seite 16 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Output Power Output Power LTE data call B3 LTE data call B7 LTE data call B20 3.6 Transmitter Tbd. 3.7 Receiver Tbd. 3.8 Environmental Specification 3.8.1 Temperature Range Range Operating temp. range -20°C … +65°C 3GPP spec. conform Operating temp. range -40°C … +85°C Note 1 Operational Performance might slightly deviate from 3GPP spec. Storage temp. range -40°C … +85°C Note 1: Due to temperature specification of the chipset, the temperature of the power manager and the temperature of the modem chip shall not exceed +85°C.
_______________________________________________________________________________________________________________ Seite 17 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 4 Evaluation Kit 4.1 Overview For the NAD V1140-xxx, there is an evaluation board available. Features: - On board 12V DC power supply (alternatively 3,8V DC direct connected, unbuffered). - USB port type B - SIM card tray - 20 pin JTAG header for debugging - 2 UART ports connected to DB9 - CODEC supported by I2S and I2C interfaces Using the evaluation board with an external power supply By default the module can be supplied by a switching regulator at 12V DC input voltage or by the module VCC at 3.8V. 3.8V supply should be able to deliver 3.5A max. Sense contacts are for supplies which support the corresponding feature. Using the evaluation board with on board 3.8V regulator For use at 3.8V simply disconnect the 12V supply and plug on 3.8V. Note: Make sure that the external power supply is not generating spikes or hazards higher than 4.0V. LTE-NAD Module gets damaged when spikes or hazards above 4.0V are applied RF Connector - For RF measurements use main antenna connector
_______________________________________________________________________________________________________________ Seite 18 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 2 Evaluation Kit for V1140-xxx.
_______________________________________________________________________________________________________________ Seite 19 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 3 Power supply for Evaluation Kit for V1140-xxx. Figure 4 SIM card and USB interfaces for Evaluation Kit for V1140-xxx.
_______________________________________________________________________________________________________________ Seite 20 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 5 RF interfaces for Evaluation Kit for V1140-xxx. Figure 6 Loudspeaker and microphone interfaces for Evaluation Kit for V1140-101.
_______________________________________________________________________________________________________________ Seite 21 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 4.2 Firmware Update For Firmware (FW) update the Windows software tool swupd.exe is available. To run a FW update following preconditions should be fulfilled: - Evaluation board is power-on and connected to laptop or PC - Qualcomm HS-USB Diagnostics 9025 Driver, version 2.0.9.1d or higher, is installed - Virtual COM port of Qualcomm HS-USB Diagnostics 9025 is identified Note: Please ensure to have a backup of your module configuration file 4.2.1 Identify Qualcomm Diagnostics Port Number Please use the Windows Device Manager to identify virtual COM port number Figure 7 Identify Virtual COM port number of Qualcomm HS-USB Diagnostics 9025 using Windows Device Manager – in provided example COM5 4.2.2 Install and Run FW Executable There is no dedicated software installation required. Please copy all files received with FW update to folder of your choice and ensure that all components are available Figure 8 Components of FW update tool Important: Before starting FW update ensure to have backup QCN file of your evaluation board.
_______________________________________________________________________________________________________________ Seite 22 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe To start update process please run the batch file swupd_start.bat and enter Virtual COM port number identified in previous step. Figure 9 Complete FW update A complete FW update will take about 2:30 minutes. Please note that there are other options to run FW update. To learn more please run swupd.exe /h. 4.2.3 Known Issues Sometimes a timeout occurs. Please simply re-run the batch file in that case. Please inform us if you experience problems updating the FW on Evaluation Board. Please check if access to Qualcomm HS-USB Diagnostics port is blocked by other program.
_______________________________________________________________________________________________________________ Seite 23 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 4.3 Windows 7 Driver Installation 4.3.1 Driver installation The released 64-bit Windows 7 USB host driver package is Qualcomm’s HK11-NA430-7_1.00.22 or higher revision, where 7_1.00.22 is the revision number. Driver can be obtained from Qualcomm. Following the license conditions, peiker is not allowed to distribute this driver. Note: There could be certificates to be installed. 4.3.2 Available interfaces The interfaces provided in Fig. 9 in Windows Device Manager will appear once - the USB driver is installed properly, - the USB cable connects EvalBoard and computer, and - the Evaluation Board is powered-up. Figure 10 Interfaces provided by Evaluation Board for OS Windows 7 In following chapters provide some information on how these interfaces could be used. 4.3.3 AT Command interface and PPP Dial-up Modem connection AT commands are used to control to some extent the modem. To send AT commands to the Modem such tools as PuTTY or similar are used. To setup PuTTY the virtual COM port can be read from Modem property information – right click in Device Manager the Modem string and select “Properties”. The assigned virtual COM port is shown in “Modem” dialog box, see in Figure 11 – Port COM7.
_______________________________________________________________________________________________________________ Seite 24 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 11 Modem Property dialog box Figure 12 Virtual COM port and modem settings Furthermore, it is recommended to add the APN string in Modem property box as shown in Figure 12. Alternatively, the APN string can be set by AT command AT+CGDCONT=1,"IP","web.vodafone.de" (Note: The latter is the special APN valid for Vodafone Germany only). Please check with your Provider the correct APN string. Figure 13 Enter the APN delivered by your MNO in Modem Property dialog
_______________________________________________________________________________________________________________ Seite 25 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Select in “Network and Sharing Center” of “Control Panel” the option “Set Up a Connection or Network” and enter here the “Connect to the Internet” option. Follow the instructions to setup a new dial-up connection. Once the connection is setup, the Dial-up Connection is available under Network Connections. Using the Windows context menu, the connection maybe activated or deactivated. Figure 14 Dial-up Connection is available under Network Connections. Note: Prior to use this connection, a valid APN for your Mobile Network Operator must be entered, see explanation above. LTE-NAD AT command set is provided in chapter 5 AT Command interface 4.3.4 RmNet NDIS connection as Network Interface Card Figure 15 The USB driver provides a NIC (Network Interface Card). Currently according to Qualcomm proprietary information on x86, x64/AMD64, and ARM (Win8 only, for WoA/WoS) architectures following NDIS versions are supported (Source: Qualcomm Solution 00007808):  NDIS 5.1: Windows XP, Server 2003, CE  NDIS 5.2: Windows Server 2003 SP2  NDIS 6.0: Windows Vista  NDIS 6.1: Windows Vista SP1, Server 2008  NDIS 6.20: Windows 7, Server 2008 R2 Note: If NIC connection is not available please check with your Service Engineer if NV# 3534 is properly set.
_______________________________________________________________________________________________________________ Seite 26 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Note: Especially for LTE the NIC interface provides much more data throughput as the PPP Dial-up Modem connection. 4.3.5 Diagnostics interface The Diagnostics Interface can be used with special Qualcomm Tools that are matter of dedicated license agreement with Qualcomm. Therefore, there is no additional information provided in this document. Note: Diagnostics Port is used for Firmware Updates as explained in chapter Firmware Update 4.3.6 NMEA GNSS interface The virtual NMEA COM port provides NMEA information, delivered by build-in GNSS receiver of LTE-NAD Module. LTE-NAD provides GPS and GLONASS location information. Please contact peiker for GALILEO support. 5 AT Command Set The modules supports standard AT command as listed below. Commands are compliant to 3GPP TS 27.007 and TS 27.005 Command Description Comment AT+CMGF Message Format AT+CSCA Service Centre Address AT+CMGS Send Message AT+CGMI Manufacturer Identification AT+CGMM Request model identification AT+CGMR Request revision identification AT+CGSN Request product serial number AT+CIMI Request international mobile subscriber identification AT+CMOD Call mode Only one Parameter is supported by the device. AT+CHUP Hang up call ATD Initiate a CS or PS call or supplementary service ATA Answer incoming CS call command ATH Hangup CS call command AT+CBST Select bearer service type AT+CEER Extended error report AT+CVHU Voice hangup control AT+CREG Network registration AT+COPS PLMN selection AT+CLCK Facility lock AT+CPWD Change password AT+CLIP Calling line identification presentation AT+CLIR Calling line identification restriction
_______________________________________________________________________________________________________________ Seite 27 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Command Description Comment AT+CCWA Call waiting AT+CHLD Call related supplementary services AT+CUSD Unstructured supplementary service data AT+CLCC List current calls AT+CPOL Preferred PLMN list AT+CPAS Phone active status AT+CFUN Set phone functionality AT+CPIN Enter PIN AT+CSQ Signal quality AT+CMER Mobile termination event reporting AT+CSIM Generic SIM access AT+CRSM Restricted SIM access AT+CMEE Report mobile termination error AT+CGDCONT Define PDP context AT+CGEQREQ Request 3G quality of service profile AT-CGATT PS attach or detach AT+CGACT PDP context activate or deactivate AT+CGPADDR Show PDP address AT+CGSMS Select service for MO SMS messages ATE Character Echo ON/OFF AT+CSMS Check Message Service support AT+CSMP Set Text Mode Parameters AT+CSDH Show Text Mode Parameters AT+CSCB Select Cell Broadcast Message Types AT+CSAS Save Settings Only one Parameter is supported by the device. AT+CRES Restore Settings Only one Parameter is supported by the device. AT+CMGL List messages AT+CNMA New message acknowledgement AT+CMGC Send Command AT+CMMS More Messages to Send AT+ATV DCE response format AT+ATX Result code selection and call progress monitoring control AT+CNMI New Message Indications to TE AT+CPMS Preferred Message Storage AT+CMGW Write Message to Memory AT+CMSS Send Message from Storage AT+CMGD Delete Messages AT+CNUM Get MSISDN AT+CPBS Select phonebook memory storage AT+CPBR Read phonebook entries AT+CPBW Writephonebook entry
_______________________________________________________________________________________________________________ Seite 28 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 6 Safety Recommendations according to EN60950-1 This device must be supplied by a limited power source according to EN 60950-1. The clearance and creepage distances required by the end product must be withheld when the module is installed. The cooling of the end product shall not negatively be influenced by the installation of the module.
_______________________________________________________________________________________________________________ Seite 29 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 7 List of Acronyms 3GPP 3 rd Generation Partnership Project ADC Analog Digital Converter ADN Abbreviated Dialing Number A-GPS Assisted GPS AMR Adaptive Multi Rate AT Attention Command AWS Advanced Wireless Services BER Bit Error Rate CLIP Calling Line Identification Presentation CLIR Calling Line Identification Restriction CSD Circuit Switch Data DARP Downlink Advanced Receiver Performance DTMF Dual Tone Multi Frequency FDN Fixed Dialing Number FTP File Transfer Protocol GSM Global System for Mobile communication GPIO General Purpose Input Output GPRS General Packet Radio Service GPS Global Positioning System HSPA High Speed Uplink Packet Access HW Hardware LED Led Emitting Diode MO Mobile Originated MT Mobile Terminated OEM Original Equipment Manufacturer PCB Printed Circuit Board PCM Pulse Code Modulation PDU Protocol Data Unit PIN Personal Identification Number RF Radio Frequency RoHs Restriction of Hazardous Substances UART Universal Asynchronous Receiver and Transmitter USB Universal Serial Bus USIM Universal Subscriber Identity Module UMTS Universal Mobile Telecommunications System WCDMA Wideband Code Division Multiple Access
_______________________________________________________________________________________________________________ Seite 30 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 8 Regulatory Certifications In the context of sections 8.1 and 8.1.1, the terms “equipment” and “device” refer equally to either V1140-100, V1140-101, V1140-103 or V1140-105. In the context of section 8.2, the terms “apparatus”, “device” and “appareil” refer equally to either V1140-101, V1140-103 or V1140-105. 8.1 USA (FCC) This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) The device may not cause harmful interference, and (2) The device must accept any interference received, including interference that may cause undesired operation. 8.1.1 FCC Warnings and Notices WARNING: The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by peiker acustic GmbH & Co. KG could void the user's authority to operate this equipment. NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
_______________________________________________________________________________________________________________ Seite 31 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 8.2 Canada (IC)  This Class b digital apparatus comply with Canadian ICES-003.  Cet appareil numérique de la classe b est conforme à la norme NMB-003 du Canada.  This device complies to Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.  Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. 8.3 OEM Responsibilities Antenna - The antenna gain, including cable loss and based on the capabilities of the module’s transmitter mounted on the PCBs specified in the related FCC filings, must not exceed 1,47dBd at 700 MHz & 850 MHz, 6dBi at 1700 MHz , 3.01dBi at 1900 MHz and 9,21 dBi at 2600 MHz for satisfying FCC RF exposure compliance. - The antenna gain, including cable loss and based on the capabilities of the module’s transmitter in a stand-alone configuration, must not exceed 0,77dBd at 700 MHz & 850 MHz, 5dBi at 1700 MHz, 2.01dBi at 1900 MHz and 8,01 dBi at 2600 MHz for satisfying FCC RF exposure compliance. - The systems antenna(s) must be installed such that 20 cm is maintained between the antenna(s) and the body of the user or nearby persons. - This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The preceding statement must be included as a Caution statement in OEM product manuals in order to alert users of FCC RF Exposure compliance.
_______________________________________________________________________________________________________________ Seite 32 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Power Regulation - The host equipment must provide power regulation circuitry to ensure that the module is supplied with stable 3.8VDC. FCC Labeling - The V1140-100 module is labeled with its own FCC ID Number. If the FCC ID is not visible when the V1140-100 module is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWY-V1140-100" or "Contains FCC ID: QWY-V1140-100" - The V1140-101 module is labeled with its own FCC ID Number. If the FCC ID is not visible when the V1140-101 module is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWY-V1140-101" or "Contains FCC ID: QWY-V1140-101" - The V1140-103 module is labeled with its own FCC ID Number. If the FCC ID is not visible when the V1140-103 module is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWY-V1140-103" or "Contains FCC ID: QWY-V1140-103" - The V1140-105 module is labeled with its own FCC ID Number. If the FCC ID is not visible when the V1140-105 module is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWY-V1140-105" or "Contains FCC ID: QWY-V1140-105" IC Labeling - The V1140-101 module is labeled with its own IC ID Number. If the IC ID is not visible when the V1140-101 module is installed inside another device, then the host device must contain the IC ID number with the statement such as the following: "Contains Transmitter Module IC: 6588A-V1140101" or "Contains IC: 6588A-V1140101". - The V1140-103 module is labeled with its own IC ID Number. If the IC ID is not visible when the V1140-103 module is installed inside another device, then the host device must contain the IC ID number with the statement such as the following: "Contains Transmitter Module IC: 6588A-V1140103" or "Contains IC: 6588A-V1140103". - The V1140-105 module is labeled with its own IC ID Number. If the IC ID is not visible when the V1140-105 module is installed inside another device, then the host device must contain the IC ID number with the statement such as the
_______________________________________________________________________________________________________________ Seite 33 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe following: "Contains Transmitter Module IC: 6588A-V1140105" or "Contains IC: 6588A-V1140105".

Navigation menu