VALEO Telematik und Akustik ATM-R-622 Advanced Telecommunication Module (ATM) Roof Version User Manual

Peiker acustic GmbH & Co. KG Advanced Telecommunication Module (ATM) Roof Version

atm_roof_user_manual_statement_ atm-01 r2-us-4gw

________________________________________________________________________________________________________________________________________ page 1 peiker acustic GmbH & Co. KG, Max-Planck-Straße 28-32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: Valeo Peiker Telematik GmbH, Vorsitzender der Geschäftsführung: Reinhard Kromer-von Baerle, Geschäftsführer: Mathias Köhler, Amtsgericht Coburg HRB 5735 Vorsitzender des Aufsichtsrates: Marc Vrecko Ein Unternehmen der Valeo Firmengruppe Statement for User Manual Advanced Telecommunication Module (ATM) ATM-01 R2-US-4GW Rev. 2.1 Release PEIKER acustic Confidential and Proprietary Name of model: ATM-01 R2-US-4GW Internal peiker product ID: 2609-078-066-51 Status: Release Revision: 2.1 Date: 30.05.2016
page 2 The copyright protection of this original document remains with Peiker acustic GmbH & Co. KG. Without prior written authorization it shall not be copied or otherwise reproduced by a third party and shall not be disclosed to competitors. The infringement shall be strictly enforced by applicable civil and criminal legal proceedings. 1 Change documentation Date Revision Name Changes / Comment 08.04.2015 Rev 1.0 M. Fleckenstein Initial version 03.05.2016 Rev 2.0 M. Fleckenstein Update to new model ATM-01 R2-US-4GW 30.05.2016 Rev 2.1 M. Fleckenstein Update WLAN frequency range
page 3 The copyright protection of this original document remains with Peiker acustic GmbH & Co. KG. Without prior written authorization it shall not be copied or otherwise reproduced by a third party and shall not be disclosed to competitors. The infringement shall be strictly enforced by applicable civil and criminal legal proceedings. 1 Change documentation ..................................................................................................... 2 2 Introduction ..................................................................................................................... 4 2.1. Scope ............................................................................................................................... 4 2.1.1. Purpose of the document ............................................................................................. 4 2.1.2. General information ..................................................................................................... 4 2.1.3. Contact information ..................................................................................................... 4 3 Wireless Communication .................................................................................................. 5 3.1. Wireless Cellular Communication ......................................................................................... 5 3.2. Wireless LAN ..................................................................................................................... 5 4 Warning Statements for the User Manual......................................................................... 6 4.1. US /Canada ....................................................................................................................... 6 5 Battery replacement ......................................................................................................... 7
page 4 The copyright protection of this original document remains with Peiker acustic GmbH & Co. KG. Without prior written authorization it shall not be copied or otherwise reproduced by a third party and shall not be disclosed to competitors. The infringement shall be strictly enforced by applicable civil and criminal legal proceedings. 2 Introduction 2.1. Scope 2.1.1. Purpose of the document The Advanced Telecommunication Module (ATM) roof version is manufactured by peiker acustic GmbH & Co. KG (grantee) and sold as an OEM product. According to the US Code of Federal Regulations (47 CFR 2.909, 2.927, 2.931, 2.1033, 15.15(b) etc.), the grantee must ensure the end-user has the applicable and appropriate operating instructions for the device. In the case of this product the grantee must notify the OEM to notify the end-user. Peiker acustic GmbH & Co. KG will supply this document to the reseller or distributor to inform him what must be included in the end user’s manual for the commercial product and which installations guidelines for the antenna are applicable. 2.1.2. General information The ATM is assembled in the car during production. There are no other distribution channels than assembly in the cars production line or spare part replacement within car service. Please be advised that this product will need special trained professionals in configuring and installing the product. The product will be distributed through controlled distribution channel which has special trained professionals to install this product and will not be sold directly to the general public through retail stores. The ATM is mounted invisible to the driver in the car below the roof antenna. The roof antenna is directly connected to the ATM. The only direct interface of the ATM to the driver or passenger is a dedicated push button and LED (i.e. Mayday_LED) to trigger an emergency call and signal the call status. Except this button and the LED, there are no direct interfaces of the ATM to the driver or passengers. The ATM is connected to the internal bus and control systems of the car. The ATM uses the external antenna of the car and also contains an internal WLAN antenna. The ATM uses a factory mounted embedded SIM module (MFF2). 2.1.3. Contact information peiker acustic GmbH & Co. KG Max-Planck-Straße 28-32 D-61381 Friedrichsdorf Germany http://www.peiker.de info@peiker.de
page 5 The copyright protection of this original document remains with Peiker acustic GmbH & Co. KG. Without prior written authorization it shall not be copied or otherwise reproduced by a third party and shall not be disclosed to competitors. The infringement shall be strictly enforced by applicable civil and criminal legal proceedings. 3 Wireless Communication 3.1. Wireless Cellular Communication Following technologies and frequency bands are supported by the device ATM-01 R2-US-4GW: RAT frequency (Mhz) band GSM 850, 1900 Dual band WCDMA 850, 1900 V, II LTE 750, 850, 1700, 1900 17, 5, 4, 2 It must be ensured by the OEM that the end user has no manual instructions to remove or install the RF unit of the device. 3.2. Wireless LAN Wireless LAN standards IEEE 802.11 b,g,n Frequency 2,4 GHz (2412MHz – 2472MHz) Channels 1 – 11 Channel bandwidth 20 MHz Modulation Depending on data rate: BPSK, QPSK, 16-QAM, 64-QAM, DBPSK, DQPSK, CCK, PBCC, ERP-PBCC Max transmitter power (output of chip) 1 mW (0dbm) Path loss on PCB (chip to internal antenna) 2 dbi Maximum antenna gain (internal WLAN antenna) 5 dbi
page 6 The copyright protection of this original document remains with Peiker acustic GmbH & Co. KG. Without prior written authorization it shall not be copied or otherwise reproduced by a third party and shall not be disclosed to competitors. The infringement shall be strictly enforced by applicable civil and criminal legal proceedings. 4 Warning Statements for the User Manual The following certification markings and hints should be printed in the end user’s manual: 4.1. US /Canada This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Radiofrequency radiation exposure Information: This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Information sur l’exposition au rayonnement électromagnétique : Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by peiker acustic GmbH & Co. KG could void the user's authority to operate the equipment.
page 7 The copyright protection of this original document remains with Peiker acustic GmbH & Co. KG. Without prior written authorization it shall not be copied or otherwise reproduced by a third party and shall not be disclosed to competitors. The infringement shall be strictly enforced by applicable civil and criminal legal proceedings. 5 Battery replacement Please be advised that this product will need special trained professionals in configuring and installing the product within the car. To open the battery compartment, push down the battery lid at the lower right corner front of the device. Remove the battery and replace it with the replacement part. Close the battery compartment by pushing the lid towards the housing.

Navigation menu