United Integrated Services ZBM-221 ZigBee Module User Manual

United Integrated Services CO., LTD. ZigBee Module

User Manual

UIS 1 | P a g e ZigBee Module User Manual ZBM-221
UIS 2 | P a g e Contents Certification Notices 1. Overview 2. Specification 3. Pin Assignment
UIS 3 | P a g e Certification Notices FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of f and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Labeling requirements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement: This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
UIS 4 | P a g e Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. This device is intended for OEM integrators only. Please see the full Grant of Equipment document for other restrictions. This device must be operated and used with a locally approved access point. Information To Be Supplied to the End User by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. Host system must be labeled with "Contains FCC ID:XBTZBM-221, FCC ID displayed on the label. The label text should be updated according to the table shown in Ordering Guide section of this document.
UIS 5 | P a g e 1. Overview ZMB-221 is a wireless communication modem based on IEEE802.15.4, which can be widely used in home automation and security, automatic meter reading, factory automation, toys and so on. 2. SPECIFICATION General SpecificationSpecificationTransmit Frequency 2405MHz to 2480MHzModulation OQPSKProgrammable Output Power Up to 20 dBmOperation Voltage 2.0V~3.6VEnvironmentalOperating Temperature -10°C to 70°CStorage Temperature -40°C to 85°CHumidity 90% RH Max., Non-CondensingMechanical SpecificationDimension (WxHxD, mm) 30.2 x 2.6 x 22.22.4-GHz IEEE 802.15.4 Compliant RF Transceiver
UIS 6 | P a g e 3. Pin Assignment
UIS 7 | P a g e Pin Name Description Direction1 GND Power Ground I2 P1_5 Port 1.5 I/O3 P1_4 Port 1.4 I/O4 P1_1 I/O30 VDD DC input(+2.0 ~3.6V) I5 GND Power Ground I6 P1_0 I/O7 P0_6 Port 0.6 I/O8 P0_5 Port 0.5 I/O9 P0_4 Port 0.4 I/O10 P0_3 Port 0.3 I/O11 P0_2 Port 0.2 I/O12 P0_1 Port 0.1 I/O13 P0_0 Port 0.0 I/O14 RESET_N Reset, active-low I15 VDD DC input(+2.0 ~3.6V) I16 GND Power Ground I17 VDD DC input(+2.0 ~3.6V) I18 GND Power Ground I19 GND Power Ground I20 RF RF Output O21 GND Power Ground I31 GND Power Ground I32 GND Power Ground I33 GND Power Ground I22 VDD DC input(+2.0 ~3.6V) I23 Port 2.4/32.768 kHz XOSC I/O24 Port 2.3/32.768 kHz XOSC I/O25 P2_2 Port 2.2 I/O26 P2_1 Port 2.1 I/O27 P2_0 Port 2.0 I/O28 P1_7 Port 1.7 I/O29 P1_6 Port 1.6 I/OPort 1.1 – 20-mA drive capabilityPort 1.0 – 20-mA drive capabilityP2_4/XOSC32K_Q1P2_3/XOSC32K_Q2

Navigation menu