Uniden America UN042 2 Line Cordless Phone System User Manual 4096

Uniden America Corporation 2 Line Cordless Phone System 4096

Contents

4096 user manual

Charger AC adapter (PS-0035)Belt clip DCX400 accessory handset and chargerIf you purchased model number:You should have:DECT4096 1 of eachDECT4096-2 2 of eachDECT4096-3 3 of eachDECT4096-4 4 of eachDECT4096-5 5 of eachDECT4096-6 6 of eachYou will also nd:Rechargeable battery pack (BT-1018)WALLDESKBattery coverDECT4096 two-line base with dual answering systems Base AC adapter (PS-0034)Telephone cord with two line supportCoiled cordCorded handsetDesk stand/wall mount bracketIf any items are missing or damaged, contact our Customer Care Line immediately. Never use damaged products!Need Help? Get answers 24/7 at our website: www.uniden.com.If You... Contact Uniden’s... Phone Numberhave a question or problem Customer Care Line*817-858-2929 or 800-297-1023need a replacement part or accessory Parts Department* 800-554-3988need special assistance due to a disabilityAccessibility Help Line 800-874-9314 (voice or TTY)* During regular business hours, Central Standard Time. Visit our website for detailed business hours.DECT4096 Series User's GuideWhat's in the box?
Important Safety Instructions!When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of re, electric shock and injury to persons, including the following: This unit is NOT waterproof. DO NOT expose this unit to rain or moisture. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a re. They may explode. Check with local codes for possible special disposal instructions. Do not place the handset in any charging cradle without the battery installed and the battery cover securely in place.SAVE THESE INSTRUCTIONS!What's in the manual?Installing Your Phone ............................ 1Set Up the Base ..................................... 1Test the Connection ............................... 3Set Up the Accessory Handset(s) .......... 4Getting to Know Your Phone................. 6Parts of the Base ................................... 6Parts of the Handset .............................. 8Reading the Displays  ..........................10Using the Soft Keys ............................. 12Entering Text on Your Phone ................ 14Using the Menus ................................. 15The Handset and Base Setup Menu ...... 16The Clock Setup Menu ......................... 17The Global Setup Menu ........................17Special Feature Menus ........................ 18Using Your Phone ................................ 19Working with Two Lines ...................... 19Using the Speakerphone ...................... 21Changing the Volume ........................... 21Using the Caller ID and Redial Lists .....22Using Seven-Digit Dialing .................... 23Using Call Waiting ...............................24Finding a Lost Handset ........................ 24Using an Optional Headset ..................24Using the Phonebook .......................... 25Setting Up Your Phonebook ................. 25Phonebook Menu Options .................... 27Chain Dialing ........................................ 27Using Multi-station Features .............. 28Expanding Your Phone .........................28Using Multi-Station Conference Calling 28Using Privacy Mode ............................ 29Using Call Transfer...............................29Using the Intercom .............................. 29Using Special Features ....................... 31Using Your Phone During a Power Failure ............................................... 31Using Do Not Disturb ........................... 31Using Call Block ................................... 31Using the Alarm Feature ...................... 33Using Voice Message Notication ....... 34Using the Answering System  ............ 35Setting Up Your Answering System ....35Getting Your Messages ....................... 37Screening Your Calls ............................ 38Using the System While You're Away from Home ........................................ 39Solving Problems ................................ 40Weak or Hard To Hear Audio  .............. 42Noise or Static On The Line .................42Resetting and Registering Handsets .... 44Handling Liquid Damage ...................... 45Important Information ......................... 46Terms Used In This Guide .................... 46Specications ...................................... 46Battery Information .............................. 46Compliance Information ....................... 47One-year Limited Warranty .................49
1Installing Your PhoneSet Up the BaseAttach the standBefore you attach the stand, you have to decide if you want the phone to rest on a desk or hang on a wall.For desktop useTurn the stand so the word DESK is right-side up (it will be on the right).Insert the tabs into the notches marked DESK at the top of the base. Press in on the latch and slip it into the notch.For wall mount useTurn the stand so the word WALL is right-side up (it will be on the right).Insert the tabs into the notches marked WALL at the bottom of the base. Press in on the latch and slip it into the notch.To remove the standPress in on the latches and slide them out of the notch. Connect the corded handsetUse the coiled cord to connect the corded handset to the connector on the left side of the base.1.2.3.1.2.3.WALLDESKDESKDESKWALLWALLDESKDESKDESKWALLWALLDESKWALLWALLDESKWALLDESKWALLWALLDESK
2Connect the power and telephone cordsConnect the base AC adapter to the AC IN 7.8V jack and route the cord as shown:For desktop use For wall mount useWALLDESKDESKDESKWALLWALLDESKWALLWALL DESKConnect the included two-line telephone cord to the TEL LINE 1/2 jack. If your phone company uses a separate phone jack for each line, connect a standard telephone cord to the TEL LINE 2 jack. Route the cords as shown above.Connect the cord from TEL LINE 1/2 to a two-line phone jack. OR If your phone company uses a separate phone jack for each line, connect the cord from TEL LINE 1/2 to the jack for line 1; then, connect the cord from TEL LINE 2 the jack for line 2.Plug the AC adapter into a standard 120 V AC power outlet.Place the phone on the wallOn the front of the base, pull the clip that holds the corded handset in place out of its slot.Rotate the clip 180 degrees. Flip it from front to back and slide it back into the slot.1.2.3.4.1.2.3.WALLDESKAC IN 7.8V TEL LINE 2 TEL LINE 1/2IF you have a separate jack for line 2, connect another phone cord here.Connect the telephone cord here first.WALLDESKAC IN 7.8V TEL LINE 2 TEL LINE 1/2IF you have a separate jack for line 2, connect another phone cord here.Connect the telephone cord here first.
3Place the mounting slots over the pins on the wall plate, and slide the base down to lock it into place.Test the ConnectionPick up the corded handset from the base. The phone should pick up line 1 automatically and change the display to show Talk , and you should hear a dial tone. When you get a dial tone, make a test call.If... Try...the display says   Check or you don't hear a dial tonechecking the connection between the base and the phone jack: make sure the cord is connected to TEL LINE 1/2.you keep hearing a dial tone setting line 1 to pulse dialing (see page 4).there's a lot of noise or staticsee page 42 for tips on avoiding interference.Test Line 2Once you can make calls on line 1, make a test call on the second line. Pick up the corded handset and press the unmarked key under LINE2. You should hear a dial tone and the display should show Talk .If... Try...the display says   Check or you don't hear a dial tonechecking the connection between the base and the phone jack: if you have a separate jack for each line, make sure the cord is connected to TEL LINE 2.you keep hearing a dial tone  setting line 2 to pulse dialing (see page 4).4.WALLDESKWALLWALL DESK(To telephone jack for second line.)WALLDESKWALLWALL DESK(To telephone jack for second line.)  0  0LINE1  MENU  LINE2    SUN 12:00A    12/31/08     0  0LINE1  MENU  LINE2    SUN 12:00A    12/31/08
4Changing from Tone to Pulse DialingPhones can communicate with the telephone network in two ways: tone (DTMF) or pulse dialing. If you know your phone company uses pulse dialing or the test call for line 1 did not work, follow these steps:With the phone in standby, press MENU.Use UP or DOWN to highlight Global Setup, then press OK.When your phone prompts you to select a line, press LINE1. Use UP or DOWN to highlight Dial Mode, then press OK. Highlight Pulse, then press OK. The phone sounds a confirmation tone. Try making another test call using line 1. If your test call on line 2 did not connect, follow the same process, but press LINE2 in step 3.If you use pulse dialing and you need to send DTMF tones during a call (if you're using an automated response system, for example), press   to temporarily switch to tone dialing. When the call ends, the phone automatically returns to pulse dialing mode.Set Up the Accessory Handset(s)If your phone came packaged with accessory handsets, follow the steps below to get your cordless handsets ready for use.Install the batteryUnpack all handsets, battery packs, and battery covers. If any handset has the battery cover already attached, press in on the notch and slide the cover down and off.Line up the red and black wires on the battery pack with the label inside the handset. Push the battery pack connector in until it clicks into place. Tug gently on the wires to make sure the battery pack is securely connected.1.2.3.4.5.1.2.3.RedBlackRedBlack
5Place the cover over the battery compartment and slide it up into place.Connect the chargerConnect a charger AC adapter to each charger's AC IN 8V jack and set the plug into the notch as shown. (These adapters might already be connected.)Plug the other end of the adapter into a standard 120V AC power outlet.Place each handset in a charger with the display facing forward. The CHARGE light should turn on.If... Try...the CHARGE light doesn't turn onreseating the handset.checking the AC adapter connection.seeing if the outlet is controlled by a wall switch.---Charge all handsets completely (about 15 hours) before using them.Test the connectionPick up each handset and press TALK. You should hear a dial tone, and the display should say Talk. (Press END to hang up.)If you can't get a dial tone or the handset display says Unavailable, try moving the handset closer to the base or resetting it (see page 44).4.1.2.3.AC IN 8VAC IN 8V
6Getting to Know Your PhoneParts of the BaseIf the key name is spelled out on the key itself, it's not labeled in the drawing below.UPPHONEBOOK/LEFTDOWNCALLER ID/ RIGHTINTERCOM/ HOLDMicrophone(on back)12-key dial padHook switchDisplayDELETESPEAKERPLAY/STOPHandset clipDO NOT DISTURBSoft keysUPPHONEBOOK/LEFTDOWNCALLER ID/ RIGHTINTERCOM/ HOLDMicrophone(on back)12-key dial padHook switchDisplayDELETESPEAKERPLAY/STOPHandset clipDO NOT DISTURBSoft keys
7Base keys and how they workKey name (and icon) What it doesPHONEBOOK/LEFT ( / )In standby or during a call: open the phonebook.During text entry: move the cursor to the left.In the first 2 seconds of a message: go to the previous message.Anytime after that: go to the beginning of this message.----PLAY/STOP  ( )In standby: start playing messages.While a message is playing: stop playing messages.--UP ( )In standby: increase the ringer volume for line 1 or line 2.During a normal call: increase the earpiece volume.During a speakerphone call or while a message is playing: increase the speaker volume.In the menu or any list: move the cursor up one line.----CALLER ID/RIGHT  ( / )In standby or during a call: open the Caller ID list.During text entry: move the cursor to the right.While a message is playing: skip to the next message.---DOWN ( )In standby: decrease the ringer volume for line 1 or line 2.During a normal call: decrease the earpiece volume.During a speakerphone call or while a message is playing: decrease the speaker volume.In the menu or any list: move the cursor down one line.----SOFT KEYSThe soft keys automatically change their function based on what you are doing. See "Using the Soft Keys" on page 12.-DELETE ( )While a message is playing: delete this message.In standby: delete all messages.While entering text: delete one character, or press and hold to delete all the characters.---ON/OFFIn standby: turn the answering system on or off.-MUTE/EXITWhile this station is ringing: mute the ringer for this call only.During a call: mute the microphone.In the menu or any list: exit the menu completely.---CONFERENCEDuring a call: conference two lines together.-INTERCOM/HOLDIn standby: page a handset using the intercom.During a call: put the call on hold and start a call transfer.--
8Key name (and icon) What it doesSPEAKER  ( )In standby: start a speakerphone call (get a dial tone).During a normal call: switch to the speakerphone.During a speakerphone call: hang up.---DO NOT DISTURB ( )In standby: turn the Do Not Disturb feature on or off (see page 31).-REDIAL/PAUSEIn standby: open the redial list.While entering a phone number: insert a 2-second pause.--Parts of the HandsetMicrophone12-keydial padMessagewaiting LED, visual ringerDisplayChargingcontactsEarpieceUPPHONEBOOK/LEFTSPEAKERDOWN CALLER ID/ RIGHTREDIAL/PAUSEINTERCOM/HOLDTALK/FLASHENDSoft keysMicrophone12-keydial padMessagewaiting LED, visual ringerDisplayChargingcontactsEarpieceUPPHONEBOOK/LEFTSPEAKERDOWN CALLER ID/ RIGHTREDIAL/PAUSEINTERCOM/HOLDTALK/FLASHENDSoft keys
9Handset keys and how they workKey name (and icon) What it doesUP ( )In standby: increase the ringer volume for line 1 or line 2.During a call: increase the call volume.In the menu or any list: move the cursor up one line.---ENDDuring a call: hang up.In the menu or any list: exit and go to standby.--CALLER ID/RIGHT ( )In standby or during a call: open the Caller ID list.During text entry: move the cursor to the right.--SPEAKER ( )Switch a normal call to the speakerphone (and back).-INTERCOM/HOLDIn standby: page another station using the intercom.During a call: put the call on hold and start a call transfer.--REDIAL/PAUSE  ( )In standby: open the redial list.While entering a phone number: insert a 2-second pause.--DOWN ( )In standby: decrease the ringer volume for line 1 or line 2.During a call: decrease the call volume.In the menu or any list: move the cursor down one line.---PHONEBOOK/LEFT ( )In standby or during a call: open the phonebook.During text entry: move the cursor to the left.--TALK/FLASHIn standby: start a telephone call (get a dial tone).During a call: switch to a waiting call.--SOFT KEYSThe soft keys automatically change their function based on what you are doing. See "Using the Soft Keys" on page 12.-
10Reading the Displays On the baseOn the handsetThe table below shows the possible icons and what they mean. Since the icons appear based on what you're doing with the phone, you won't ever see all of these icons at the same time.Base Icon Handset Icon What it means or  The accompanying information (in use, on hold, etc.) applies to line 1. or  The accompanying information (in use, on hold, etc.) applies to line 2.1 21 2LINE1  MENU  LINE2    SUN 12:00A    12/31/08   New CID: 4Answeringsystem status for:Status icon areasCaller IDcountDay & timeCurrentfunctionsfor: Soft key 1 Soft key 2 Soft key 3DateLine 2Line 11 21 2LINE1  MENU  LINE2    SUN 12:00A    12/31/08   New CID: 4Answeringsystem status for:Status icon areasCaller IDcountDay & timeCurrentfunctionsfor: Soft key 1 Soft key 2 Soft key 3DateLine 2Line 1   SUN 12:00A   Handset #1   New CID: 2LINE1  MENU  LINE2 HandsetbannerStatusiconsCaller ID countDay and timeCurrentfunctions for:Soft key 1 Soft key 2 Soft key 3   SUN 12:00A   Handset #1   New CID: 2LINE1  MENU  LINE2 HandsetbannerStatusiconsCaller ID countDay and timeCurrentfunctions for:Soft key 1 Soft key 2 Soft key 3
11Base Icon Handset Icon What it means         The ringer is turned off for 1) line 1 only, 2) line 2 only, or 3) both. This station will not ring when a call comes in on the indicated lines.You have a voice message waiting (see "Using Voice Message Notification" on page 34).Privacy Mode is on: no other station can join your call.The speakerphone is on.The microphone is muted, and the caller can't hear you.NA The alarm is set. (See "Using the Alarm Feature" on page 33.) NA T-coil mode is on. (See "Do you use a T-coil hearing aid?" on page 43.) NA       The battery is 1) fully charged, 2) half charged, 3) getting low, or 4) empty.NA       The signal from the base is 1) very weak, 2) low, 3) strong, or 4) very strong.Answering system status iconsThe icons on the right hand side of the base display indicate the status of the answering system. Each icon will appear separately for line 1 (at the top) and line 2 (at the bottom). See Using Your Answering System on page 35 for more information.Icon What it meansThe answering system is off: it will not answer the phone.The answering system is set to announce only: it will answer the phone but will not record any messages.The answering system memory is full: you must delete some saved messages.01 through 59This number indicates the number of new messages for each line.
12Using the Soft KeysSoft keys are controlled by the software: they will automatically change their function depending on what you're currently doing:Soft keys with the phone in standbyOn the base On the handset1 21 2LINE1  MENU  LINE2    SUN 12:00A    12/31/08   New CID: 4Soft key 1 Soft key 2 Soft key 3   SUN 12:00A   Handset #1   New CID: 2LINE1  MENU  LINE2 Soft key 1Soft key 2 Soft key 3Soft keys in the main menuOn the base On the handset1 2OK Back     <Options>Global SetupCall BlockingSoft key 1 Soft key 2 Soft key 3   <Options>Global SetupCall BlockingOK Back Soft key 1Soft key 2 Soft key 3The description of the soft key's current function appears in the bottom of the display directly above the corresponding key. 
13If the description for a soft key is blank, that key doesn't currently have a function.Sometimes, the current function of a soft key can duplicate the function of a regular key. If this happens, you can press either key.When this manual refers to a soft key, it uses the soft key's description printed on a black background. Common soft key descriptionsThe table below lists some soft key descriptions that the phone uses across several menus or operations. These are not all the soft key descriptions, but these are probably the ones you'll see most often.Soft key description: What it does:BACKGo back to the previous screen. Any unsaved changes on the current screen will be canceled.BLOCKBlock all calls from the incoming phone number.CANCELCancel the current operation without saving any changes.DELETEErase the highlighted item.LINE1Use line 1 for the current operation.LINE2Use line 2 for the current operation.MENUOpen the main menu screen.MUTETurn off the ringer, speaker, or microphone.OKSelect the highlighted option or confirm the current operation.OPTIONSShow available choices for the current operation or for the highlighted item. SELECTChoose the highlighted option.
14Entering Text on Your PhoneWhen you want to enter text into your phone (for example, a name in the phonebook), use the twelve-key dial pad to enter the letters printed on the number keys. Here's how it works:The phone enters the letters in the order they appear on the key. For example, if you press the number key 2 once, the phone enters the letter A. Press 2 twice for B, and three times for C. If you press the key again after the last letter, the phone starts the same letter sequence with small letters. If you press 2 four times in a row, the phone enters a (small letter). Press 2 five times for b, and six times for c.If you see the icon [Aa] in the display, the phone enters capital letters first (A B C), then small letters (a b c), then the number on the key (2). The icon [aA] means the phone starts at the small letters, so it enters small letters first, then the number on the key, then capital letters.The phone automatically uses a capital letter for the first letter and any letter right after a space; all other times, it uses small letters.If two letters in a row use the same number key, enter the first letter, then use CALLER ID/RIGHT to move the cursor to the next position to enter the second letter. Switch between capital and small letters Press  .Move the cursorPress PHONEBOOK/LEFT to move the cursor to the left or CALLER ID/RIGHT to move the cursor to the right.Leave a blank space Press # (POUND). Erase one letterMove the cursor to the letter you want to erase and press the DELETE soft key. (On the base, you can also press DELETE.)Erase the entire entry Press and hold DELETE.Enter punctuation or a symbol Press 0 to rotate through the available symbols. 
15Using the MenusThe menus are designed to be as easy as possible. Some users don't even need the manual once they know how to perform these actions: If you don't press any keys for thirty seconds, the phone times out and exits the menu. (When setting the day and time, the time-out period is extended to two minutes.)Open the menu Press MENU.Move the cursorThe cursor (the black bar with the white text) shows which menu item is currently highlighted; when you're entering characters, the cursor shows where you are in the line. Use UP to move the cursor up one line.Use DOWN to move it down one line.Use PHONEBOOK/LEFT to move it one space to the left.Use CALLER ID/RIGHT to move it one space to the right. -----Select an option Move the cursor to highlight the option, then press OK.Return to the previous screenPress BACK. If you press BACK on the first screen, the phone exits the menu.Close the menuOn the handset, press END; on the base, press MUTE/EXIT.(If you open the menu during a call, press BACK to back out of the menu without hanging up.)To open the menu, pressSelect the highlightedoptionTo close the menu:Use UP and DOWN to move the cursorMENU Go back to the previous screenon the handset, presson the base, pressOK BACK   <Options>Retrieve MsgHandset SetupAns. SetupClock SetupGlobal SetupCall BlockingTo open the menu, pressSelect the highlightedoptionTo close the menu:Use UP and DOWN to move the cursorMENU Go back to the previous screenon the handset, presson the base, pressOK BACK   <Options>Retrieve MsgHandset SetupAns. SetupClock SetupGlobal SetupCall Blocking
16The next several pages list all the available menu options and how to use them. Most of the menus are the same for the base and cordless handsets; any option that is available only for the base or handset is noted in the description.The Handset and Base Setup MenuWhen you open the menu on a handset, this menu is called Handset Setup. On the base, this menu is called Base Setup. Each of these options can be set separately for each station. (A station can be any cordless handset or the base.)Menu option: Use it to:T-coil(Handset only) Turn on T-coil mode to reduce noise on some hearing aids (see "Do you use a T-coil hearing aid?" on page 43). Alarm Setting(Handset only) Set alarms on your handset (see "Using the Alarm Feature" on page 33).Primary LineSelect the line you want this station to use as the default line when you make a call (see "Setting the primary line" on page 19).Ringer Tones(Handset only) See the ring tones the handset is using as the main ring tone for each line. To change the tone, select the line, then choose a ring tone from the list. (As you highlight each ring tone, the phone plays a sample of the tone. When you hear the tone you want, press OK.)Personal Ring(Handset only) Turn on the personal ring feature. If you have Caller ID, this feature lets you assign special ring tones to anyone in your phonebook: this handset will use the special ring tone when that person calls.Autotalk(Handset only) Turn on Auto Talk so you can answer the phone just by picking up the handset from the cradle (without having to press any buttons).Any Key Answer(Handset only) Turn on Any Key Answer so you can answer the phone by pressing a key on the twelve-key dial pad.Banner(Handset only) Change the name used on the handset's display. Enter any name up to 10 characters.
17Menu option: Use it to:Handset/Base LanguageChange the language used in the display.LCD ContrastChange the contrast of the display.Key Touch ToneHave the keypad sound a tone when you press a key.The Clock Setup MenuYou must set the date and time if you want to use the handset's alarm feature; setting the clock will also ensure the answering system stamps your messages with the correct time and day. You can set the clock from the base or any cordless handset.Open the menu and select Clock Setup.Use the numbers on the twelve-key dial pad to enter the date.Move the cursor to the next line, then use the dial pad to enter the time.Press  to switch between AM and PM; when you're finished, press SAVE. The Global Setup MenuThe settings on this menu are separate for each line: changing the settings for line 1 will not affect line 2, and vice versa. However, the settings for each line apply to all stations whenever they use that line.Before changing these settings, make sure the phone is in standby and all handsets are within range of the base. (Only one station at a time can change these settings.)When you select the Global Setup menu, the phone prompts you to select Line 1 or Line 2. Then, you can choose one of the following options to change the global settings for that line:Menu option: Use it to:Area CodeEnter your area code so the phone hides the area code on incoming local calls (see "Using Seven-digit Dialing" on page 23).1.2.3.4.
18Menu option: Use it to:Dial ModeChange the way your phone communicates with the telephone network (see "Changing from Tone to Pulse Dialing" on page 4).Set Line ModeDo not change this setting unless instructed to by customer service. VMWI Reset(Base only) Reset the voice message waiting indicator to bring it back into sync with your voice mail service (see "Using Voice Message Notification" on page 34).Special Feature MenusThe following menus control specific features of your phone. These menus are explained under the section that describes the feature in detail:Menu: Use it to: For details, see:Retrieve Msg (handset only)Access your answering system from a cordless handset"Getting Your Messages" on page 37Ans. SetupChange the settings for the answering system on each line. "Ans. Setup menu options" on page 36Register Handset (base only)Add new handsets or reset a handset that isn't working properly."Resetting and registering handsets" on page 44Call BlockingBlock unwanted calls from up to 20 phone numbers and manage your call block list ."Using Call Block" on page 31
19Using Your PhoneWorking with Two LinesWhen performing common tasks, you can let the station use the primary line, or you can manually choose a particular line for each task. Using the primary line makes common tasks much simpler, but you will need to assign a primary line to each station (see below).If you want to... From the base From a cordless handsetmake a callwith the primary line-Dial the number, then pick up the corded handset.Dial the number, then press TALK/FLASH.by choosing a line-Dial the number, then press LINE1 or LINE2.*answer a callWhen a call comes in, the soft keys blink to tell you which line is ringing.with the primary line-Pick up the corded handset. Press TALK/FLASH.by choosing a line-Press the soft key for the line you want to answer.*hang up Return the handset to the cradle.Press END or return the handset to the cradle.put a call on holdPress INTERCOM/HOLD; the soft key blinks to remind you the line is on hold. To return to the call, press the soft key (LINE1 or LINE2) for the holding line.switch lines during a call (automatic hold)Press the soft key for the other line; the current call is automatically put on hold (see above). To return to the call, press the soft key for the holding line.mute the microphone during a callPress MUTE/EXIT.  Press MUTE. Press again to turn the microphone back on.mute the ringer for this call onlyWhile the phone is ringing, press MUTE/EXIT.While the phone is ringing, press END.*  On the base, pick up the corded handset to switch from the speaker to the earpiece.Assigning a primary lineYou can assign a primary line to each station; the station connects to its primary line whenever it goes off hook (that is, when you press TALK/FLASH on a handset, pick up the corded handset from the base, or press SPEAKER). You can bypass the primary line assignment by manually choosing line for your current task.
20To assign a primary line, open the menu and select Handset Setup or Base Setup. Select Primary Line, then choose the line you want this station to connect to when it goes off hook:Line 1Always connect to line 1, regardless of either line's status.Line 2Always connect to line 2, regardless of either line's status.Auto (default setting)Connect to line 1 except under the following circumstances:there is an incoming call on line 2there is a holding call on line 2the answering system has picked up line 2line 1 is being used for an active call or for screening a callIf any one of these conditions is true, the station connects to line 2.----Conferencing two lines togetherWhen you have active calls on both lines, you can join the two lines together in a conference call. Place the first call on hold.Switch to the other line and start the second call.Press MENU, then select Conference. (On the base, you can also press CONFERENCE.) During a conference call, you can speak with both outside callers at the same time, and the callers can speak with each other.To separate the conference call back into two independent calls, press the soft key for either line. The other line is automatically put on hold, and you can switch between calls normally.To disconnect both callers at the same time, just hang up normally (press END or put the handset back in the cradle). To disconnect one caller at a time, select the line you want to disconnect, then hang up. Press the soft key to return to the other caller (on hold). Other stations can also join in the conference call. See Using Multi-station Features on page 28 for more information.1.2.3.
21Using the SpeakerphoneBoth the handset and the base have a speakerphone. To use the base speaker, press SPEAKER instead of using the corded handset. To use the handset speaker, press SPEAKER instead of TALK/FLASH.To... From the base From a handsetmake a call: Dial the number, thento use the primary line -Press SPEAKER. Press SPEAKER.to choose a line-Press LINE1 or LINE2.* answer a call on the primary line -Press SPEAKER. Press SPEAKER.by choosing a line-Press LINE1 or LINE2.*switch a call to the speakerphone Press SPEAKER. Press SPEAKER.switch back to the earpiece Pick up the corded handset. Press SPEAKER.hang up a speakerphone call Press SPEAKER. Press END.*  On the handset, press SPEAKER to switch from the earpiece to the speakerphone.Changing the VolumeYou can set the volume of the ringer, the earpiece, and the speaker-phone separately for the base and each cordless handset. The available volume levels and how to change them are listed below; for each item, press UP to make it louder or DOWN to make it softer. Change the  When On the base On a handsetringer volumethe phone is in standby select a line, then select Off, Low, Medium, or Highearpiece volumeyou are on a normal callchoose one of 6 volume levels for the active linespeaker volumeyou use the speaker-phone for a call or getting messages choose one of 10 volume levels for the active linechoose one of 6 volume levels for the active line
22Using the Caller ID and Redial ListsYou have to subscribe to Caller ID to use Caller ID features: contact your telephone provider for more information.Caller ID list information Redial list informationWhen a call comes in, the phone displays the caller’s number and name (if available) along with which line is receiving the call. The phone saves the information for the last 50 calls received on either line to the CID list. The phone records which line the call came in on.When it's in standby, each station displays the total number of calls received on both lines since the last time you checked the CID list.You can edit the list separately on each station.----Each station has its own redial list.The redial list contains the last 10 phone numbers dialed from that station.The redial list does not record which line was used to dial the number.---Using the listsOpen the CID list Press CALLER ID/RIGHT.Open the redial list Press REDIAL/PAUSE.Scroll through the CID or redial listPress DOWN to scroll through the list from newest to oldest. Press UP to scroll from oldest to newest.Close the CID or redial listPress END on a handset or MUTE/EXIT on the base.  (If you open the CID list during a call, press BACK to back out of the list without hanging up.)Dialing from the CID or redial listFind the entry you want to dial.If the phone number is a toll or long distance call, but there's no 1 at the front of the record, press   to add the 1. To dial the entry with the primary line for this station, press TALK/FLASH or pick up the corded handset from the base; to manually choose a line, press LINE1/LINE2 to dial the entry.You can also go off hook before you open the list. Press TALK/FLASH or pick up the corded handset (for the primary line) or press LINE1/LINE2. Find the entry you want, then press DIAL.1.2.3.
23Caller ID and redial menu optionsOpen the CID or the redial list. Find the entry you want and press OPTIONS. Choose one of the following:Store into PBAdd the selected CID/redial list entry to this station's phonebook. The phone creates a new phonebook entry, then prompts you to edit the name and phone number; cordless handsets also prompt you to choose a personal ring (see page 25).Store & EditAppend the selected phone number to an existing phonebook entry. The phone prompts you to select the phonebook entry you want to add the number to, then opens that entry for editing (see page 26).Delete EntryErase this entry from the CID or redial list.Delete All Erase all entries from this station's CID or redial list. (This doesn't affect the CID or redial lists on any other stations.)Add Call Block(CID list only) Add this entry to the call block list (see page 31).Using Seven-Digit DialingIf you can make a local call by dialing only seven digits instead of ten, you can tell the phone to hide your local area code in the CID list. Do not enter an area code if your phone company requires ten-digit dialing. You might not be able to dial from the CID list.With the phone in standby, open the menu and select Global Setup.Press LINE1 or LINE2, then select Area Code.Use the number keypad (0 - 9) to enter a three-digit area code.Press OK when you’re finished. The phone uses the programmed code as a filter. When calls come in, the phone compares the incoming area code to the one programmed for that line. If they match, the phone hides the area code in the CID list.While reviewing the list, press # to toggle the area code off and on.When you dial from the CID list or save the number to the phonebook, the phone dials or stores the number exactly as it is currently displayed. 1.2.3.4.
24Using Call WaitingA Call Waiting call refers to a call received on a line while that line is already in use. Call Waiting and Caller ID on Call Waiting are services provided by your telephone company. You must subscribe to these services to use these features.Call Waiting is independent for each line: Call Waiting calls do not roll over to the second line.When you get a Call Waiting call, the phone sounds a tone and displays any CID information received for the waiting call.  To answer a Call Waiting call, press FLASH on the base or TALK/FLASH on a handset. The phone company automatically puts the current call on hold and switches you to the waiting call.Use FLASH and TALK/FLASH to switch between the two calls; remember, each time you switch, there is a short pause before you're connected to the other caller. Finding a Lost HandsetWith the phone in standby, press INTERCOM/HOLD on the base. Select the handset you want to find, or select All to page all handsets at the same time. The paged handset(s) will beep for 1 minute or until you press INTERCOM/HOLD again or press TALK/FLASH followed by END on the handset.Using an Optional HeadsetYou can use a standard 2.5 mm telephone  headset with your cordless handsets. To purchase headsets, contact the Parts Department (see the front  cover).To install a headset, remove the headset jack cover and insert the headset plug into the jack.Just make and receive calls as usual, and use your headset to talk to the caller after the call connects.When you connect a headset, the handset automatically mutes the earpiece and speaker. To re-activate the earpiece or speaker, just unplug the headset.(Belt clip hole)(Belt clip hole)
25Using the PhonebookEach station can store up to 100 entries in its phonebook, and each entry can have two different phone numbers. Open the phonebook Press PHONEBOOK/LEFT.Scroll through the entriesPress DOWN to scroll through the phonebook from A to Z or UP to scroll from Z to A.Jump to entries that start with a certain letterPress the number key corresponding to the letter you want to jump to.Quick dial the primary number for an entryFind the entry you want to dial.Press TALK/FLASH on a handset or pick up the corded handset from the base. The phone automatically dials the number in the first phone number slot.1.2.Dial either number for an entryFind the entry you want to dial and press SELECT. Select one of the two phone numbers for that entry.On a handset, press TALK/FLASH. On the base, pick up the corded handset.1.2.3.Use a speed dial number to open a phonebook entryOn the dial pad, press and hold the number assigned to the phonebook entry you want. The phone opens the phonebook and goes directly to that entry. Follow the instructions for dialing an entry above.Close the phonebookOn the handset, press END; on the base, press MUTE/EXIT. (If you open the phonebook during a call, press BACK to back out without hanging up.)Setting Up Your PhonebookCreating a new entryOpen the phonebook with the phone in standby, and press NEW. The phone walks you through the phonebook entry items in the order listed below. On each screen, press OK when you're finished editing the item or if you want to skip the item: Edit NameEnter the name (up to 16 characters) you want to use for this entry.
26Edit Number1Enter the primary number (up to 32 digits) for this entry exactly the way you would dial it. If you need the phone to wait before sending the next set of digits, press REDIAL/PAUSE to enter a two-second pause. If two seconds isn't long enough, you can enter as many pauses as you want.Each pause counts as one digit (you'll see a P in the number).---Edit Number2Enter the secondary number for this entry just like you did the primary number.Personal Ring selection(Handset only) Choose the ring tone you want the handset to use when this person calls. As you highlight each ring tone, the handset sounds a sample of that tone.  Speed DialSelect the speed dial number (SPD0 through SPD9) you want to assign to this entry.The speed dial numbers correspond to the numbers (0 through 9) on the twelve key dial pad. Each speed dial number can be assigned to only one entry.If the speed dial number is already assigned, the phone shows the name of the entry assigned to the number. If you want to change it, select the number, and the phone asks if you want to overwrite the existing assignment.---Editing an existing entryWith the station in standby, open the phonebook and find the entry you want. Press OPTIONS, then  choose Edit Selection.Highlight the individual item you want to change and press SELECT. The phone goes to the edit screen for that item.Edit the item as described under "Creating a new entry" (above), and press OK. OR press BACK to cancel editing and return to the main entry.Highlight the next item you want to edit and press SELECT. If you're finished editing this entry, press SAVE.1.2.3.4.5.SAVE SELECT BACK      EditBob Smith  987-555-1234123-555-9876  Clatter  Speed Dial 4Edit NameEdit Number1Edit Number2Personal ring (handset only)EditSpeedDialSAVE SELECT BACK      EditBob Smith  987-555-1234123-555-9876  Clatter  Speed Dial 4Edit NameEdit Number1Edit Number2Personal ring (handset only)EditSpeedDial
27Phonebook Menu OptionsOpen the phonebook with the phone in standby, and press OPTIONS to open the phonebook menu. From the main phonebook screen, you have two options:Copy AllCopy the whole phonebook to another station. (You must have at least one cordless handset to use this multi-station feature.)Delete All Erase all the entries in this station's phonebook. (This does not affect the entries saved on any other stations.)If you select an individual entry and then press OPTIONS, you have these additional options: Create NewAdd an entry to your phonebook. (See "Creating a new entry" on page 25.)CopyCopy this entry to another station. (You must have at least one accessory handset to use this multi-station feature.)EditEdit this entry. (See "Editing an existing entry" on page 26.)DeleteErase this entry.Chain DialingIf you often have to enter a series of digits or a code number during a call, you can save that code number to a phonebook entry and use the phonebook to send the code number.Enter the code number (up to 32 digits) into the phonebook just like a regular phonebook entry. Be sure to enter the code number into the phonebook exactly as you would enter it during a call. During your call, when you hear the prompt to enter the code number:Open the phonebook and find the entry that contains your code number.Press SELECT and select the number (phone number 1 or 2) you want. Press DIAL to transmit the code. The phone transmits the code number exactly as you entered it in the phonebook. OR if you change your mind, use BACK to close the phonebook.1.2.3.
28Using Multi-station FeaturesThe expandable base works together with the accessory handsets to give you some useful multi-station features. (A station can be any cordless handset or the base.) You must have at least one accessory handset to use the features in this section.Expanding Your PhoneYour base supports a total of ten DCX400 accessory handsets, including any that were supplied with your phone.Your base might be compatible with other Uniden accessory handsets: please visit our website for a list of compatible handsets.Accessory handsets must be registered to the base before you can use them. Handsets that aren't registered display a Handset not registered message. For instructions on registering handsets to this base, see page 44 or refer to the manual that came with the accessory handset.Any accessory handsets that came packaged with the base are already registered to that base for you. If a handset was previously registered to a base, you have to reset it so you can register it to a new base (see page 44 for DCX400 handsets).Using Multi-Station Conference CallingWhen an outside call comes in on either line, the base and four cordless handsets can join in a six-way conference call with the outside caller. To join a call in progress,  just connect to the active line (press LINE1 or LINE2). To leave a conference call, hang up normally; all other stations remains connected to the call.If you conference line 1 and line 2 together (see page 20), the base and four cordless handsets can hold a seven-way call with both outside callers at the same time.
29You can also use the speakerphone for a conference call, just like you can with a normal call.Using Privacy ModeYou can prevent other stations from joining a call. Start your call as usual, then press MENU and select Call Privacy. When you hang up, privacy mode turns off automatically.As long you have privacy mode on, no other stations can interrupt your call (you'll see a   in the handset display and a   in the base display). To allow another station to join the call, just turn privacy mode off by repeating the process above (press MENU and select Call Privacy). Using Call TransferTo... From the base From a cordless handsettransfer a callPress INTERCOM/HOLD to put the call on hold.1.Select the station you want to transfer the call to, or select All to page all the stations at the same time. When the other station accepts the call, you'll be disconnected, but you can join the call again.2.cancel a transferPress SPEAKER to return to the call.Press TALK/FLASH to return to the call. accept a transferred callTo answer the page and speak to the transferring station,1.pick up the corded handset. press INTERCOM/HOLD.To accept the call, press the soft key (LINE1 or LINE2) for the holding line.2.Using the IntercomHere are some things you need to know about using the intercom:Whenever the phone is in standby, you can make an intercom call between stations without using the phone line.You can make an intercom call from any station, but only two stations can be in an intercom call at any time.
30If an outside call comes in during an intercom call, the phone shows the CID information. If the other station hasn't answered the page, the phone cancels the page so you can answer the incoming call.To... From the base From a cordless handsetmake an intercom pagePress INTERCOM/HOLD.1.Select the station you want to talk with, or select All to page all the stations at the same time.2.cancel a page Press INTERCOM/HOLD.Press END.answer an intercom pagePress INTERCOM/HOLD or pick up the corded handset.Press INTERCOM/HOLD or TALK/FLASH.leave an intercom call Press INTERCOM/HOLD.Press END.answer an outside call during an intercom callPress the soft key (LINE1 or LINE2) for the line you want to answer. The phone automatically disconnects the intercom call and connects you to the outside line. 
31Using Special FeaturesUsing Your Phone During a Power FailureBecause it includes a corded handset, your phone can perform several of its functions during a power failure. The following features will operate during a power failure (all other features are disabled):Making and receiving calls with the base corded handset.Changing the volume on the corded handset.Using Call Waiting on a base corded handset call.Entering pauses when dialing from the base corded handset.Only line 1 is available during a power failure.While the power is out, the base uses a special ringer; you cannot adjust the volume of this ringer.Using Do Not DisturbThe Do Not Disturb or DND feature turns off the ringers of the base and all handsets at the same time.With the phone in standby, press and hold DO NOT DISTURB on the base. The phone automatically turns on the answering system and shows Do Not Disturb in the display on all stations. To cancel, press DO NOT DISTURB again.If you turn the answering system off while DND is on, the phone turns off DND along with the answering system.Using Call BlockIf you subscribe to Caller ID, you can block incoming calls by adding numbers to the call block list. When either line receives a call, the phone compares the received phone number to the numbers on the call block list. If the phone number is on the list, the phone replaces the caller's name with Call Blocked and disconnects the call. (The caller hears a reject tone.)The call block list holds 20 entries; this list applies to all stations and both lines. 
32You can add a number to the call block list through the CID options (select Add Call Block), through the Call Blocking menu (select Create New) or by blocking an incoming call (see below). Only one station can edit the call block list at a time.Blocking incoming callsWhen the phone rings, wait until the display shows the Caller ID information (usually after the second ring). If you want to block the call and add this number to the call block list, press BLOCK. When the phone asks you to confirm, press MENU or BLOCK.Blocking an incoming call from an "Unknown" or "Private" number is the same as selecting Unknown Number or Private Number from the Call Blocking menu. Call Blocking menu optionsWith the phone in standby, open the menu and select Call Blocking. Choose one of these options:View NumberSee the numbers on your call block list.Create NewAdd an entry to your call block list. The phone will prompt you to enter a name and phone number. Unknown NumberBlock all calls from numbers reported by CID as "Unknown". (This does not count as one of the 20 entries.)Private NumberBlock all calls from numbers reported by CID as "Private." (This does not count as one of the 20 entries.)Call block entry optionsWith the phone in standby, open the call block list and find the entry you want. Press OPTIONS to open the individual entry menu. Choose one of these options:EditEdit this entry. The phone will prompt you to edit the name and phone number. DeleteErase this entry from the list and allow calls from this number.
33Using the Alarm FeatureYou can set 3 different alarms on each cordless handset so your phone can remind you of important events. When an alarm is set, the alarm icon ( ) appears on the top of the screen. Setting an alarmOpen the menu and select Handset Setup.Select Alarm Setting, then select the alarm (Alarm1, Alarm2, or Alarm3) you want to set.To turn on the alarm, select On. The phone goes to the alarm edit screen.Highlight the time setting and press SELECT.Use the number keys to set the time you want the alarm to ring; press OK when you're finished.Highlight the repeat setting and press SELECT. Select how often you want the alarm to ring—once only (1 time), every day (Daily), or on a weekly basis (Select Days)—then press OK.If you choose Select Days, the handset prompts you to choose which days of the week the alarm should ring. To choose a day, highlight it and press SELECT; a check mark appears beside that to show that it is selected. Select as many days as you want, then press OK. The alarm will ring on each day with a check mark beside it. Highlight the ringer setting and press SELECT.Select the ring tone you want the alarm to use, then press OK.When you are finished setting all the alarm options, press SET to activate the alarm. The time and repeat setting will show on the main Alarm Setting screen. (If you selected specific days, the repeat setting displays as Weekly.)1.2.3.4.5.6.7.8.9.10.    Alarm 100:00AM1 timeNo SelectionSET SELECT BACK Time settingRepeat settingRinger setting    Alarm 100:00AM1 timeNo SelectionSET SELECT BACK Time settingRepeat settingRinger setting  Select DaysMonday  TuesdayOK SELECT BACK   Select DaysMonday  TuesdayOK SELECT BACK  Alarm Setting08:00AM WeeklyAlarm2OK BACK  Alarm Setting08:00AM WeeklyAlarm2OK BACK
34When an alarm ringsWhen the day and time on the phone matches the day and time of an alarm setting, the handset sounds the selected tone and displays the alarm screen.To temporarily turn off the alarm, press SNOOZE. The alarm will ring again in five minutes.To turn off the alarm completely, press END. When the phone prompts you to confirm, press YES.Using Voice Message NoticationThis feature supports Frequency-Shift Keying (FSK) message notification. Contact your voice mail provider for more details.If you subscribe to a voice mail service, your phone can notify you when you have a new message waiting on either line. When you have new messages, the voice message icon () appears in the display, and the new message light (at the top of the handset) blinks. Resetting the voice message indicatorIf the voice message icon remains after you check your messages, you can reset it from the base:Open the menu and select Global Setup.When the phone prompts you to select a line, press LINE1 or LINE2.Select VMWI Reset, then select Yes to reset the indicator.1.2.3.     AlarmSNOOZE      AlarmSNOOZE
35Using the Answering System Each line has a separate answering system. Whenever you access the answering system, the phone prompts you to choose a line. After that, any settings or operations will affect only the answering system for that line. For example, deleting all the messages from the answering system from line 1 does not affect any messages on the answering system for line 2. Setting Up Your Answering SystemRecording your outgoing messageYour personal outgoing message or greeting can be between 2 seconds and 30 seconds long. If you don't want to record an outgoing message, the system will use its pre-recorded greeting:Hello, no one is available to take your call. Please leave a message after the tone.To record your greeting:Open the menu and select Ans. Setup. Select Line 1 or Line 2, then select Record Greeting.Press START. Wait for the system to say "Record greeting" and then and begin your recording.When you're finished, press STOP. The system plays back your new greeting.To keep this greeting, press STOP again. To delete it and try again, press DELETE.Switch between the pre-recorded greeting and your greetingOpen the menu and select Ans. Setup. Select Line 1 or Line 2, then select Greeting Options.The system plays back the current greeting (personal or pre-recorded) for this line. Press CHANGE to switch greetings or OK to keep the current greeting.1.2.3.4.5.1.2.3.
36Delete your greetingOpen the menu and select Ans. Setup. Select Line 1 or Line 2, then select Greeting Options.While the system plays back the current greeting, press DELETE to erase the personal greeting for this line. (You can't erase the pre-recorded greeting.)Ans. Setup menu optionsYou can change the answering system options separately for each line. When you select the Ans. Setup menu, the phone prompts you to select Line 1 or Line 2. Then, you can choose one of the following options to change the answering system settings for that line: Security CodeEnter a 2-digit PIN so you can access your answering system from any touch-tone phone (see page 39).Ring TimeSet the number of rings (2, 4, or 6) before the answering system answers the phone. Choose Toll Saver (TS) to have the system pick up after 2 rings if you have new messages or after 4 rings if you don't.Record TimeSet the amount of time callers have to leave a message, either 1 minute or 4 minutes. Choose Announce Only if you don't want the system to let callers to leave a message.Message AlertHave the system beep every 15 seconds when you have a new message; the beeping stops when you listen to all your new messages. (To mute the alert without listening to your messages, press any key on the base.)Ans. LanguageChange the language of the system's voice prompts.Call ScreenTurn on the call screen feature so you can hear callers as they leave messages on the base speaker (see page 38).Ans. On/OffTurn your answering system on or off. (To turn your system on or off from the base, just press ON/OFF.)Record GreetingRecord a personal greeting (see page 35).Greeting OptionsSwitch between your personal greeting and the pre-recorded greeting or delete your personal greeting (see page 35).1.2.3.
37Getting Your MessagesAccessing your system from a handset (remote operation)You can access your system from a handset whenever the phone is in standby. Only one handset at a time can access the system through remote operation, and you can't use remote operation if the base is using the answering system.To start remote operation, open the menu and select Retrieve Msg. When the phone prompts you to select a line, press LINE1 or LINE2.During remote operation, the handset beeps to let you know it's waiting for your next command. If you don't press any keys for 30 seconds, the phone returns to standby.The icons on the handset's number keys and display show you which number key activates each answering system command; these commands correspond to the answering system keys on the base:Icon Command Name Handset key  Base keyPlay2PLAY/STOPStop5PLAY/STOPRepeat1PHONEBOOK/LEFTSkip3CALLER ID/RIGHTDelete4DELETEHow to operate your answering systemTo... From the base From a handset (during remote operation)play new messagesPress PLAY/STOP then select a line.Press 2. The system announces the number of new and old messages, then plays the first new message followed by the day and time it was received. Then the system plays the new messages in the order they were received.restart the current message Press PHONEBOOK/LEFT. Press 1.
38To... From the base From a handset (during remote operation)replay previous messagesPress PHONEBOOK/LEFT repeatedly until you hear the message you want to replay.Press 1 repeatedly until you hear the message you want to replay.skip a message Press CALLER ID/RIGHT. Press 3. delete a messageWhile the message is playing, press DELETE.While the message is playing, press 4.delete all of your messagesWith the phone in standby, press DELETE. When the system prompts you to select a line, press LINE1 or LINE2.Not available.play old messagesAfter the system plays the new messages, press PLAY/STOP again. When the system prompts you to select a line, press LINE1 or LINE2.press 2.exit the system Press PLAY/STOP.  Press END.Screening Your CallsAnother feature your answering system gives you is call screening. While the system is taking a message, you can hear the caller on the base speaker (if you turn on Call Screen) or from a handset.To... From the base From a handsethear the caller leaving a messageJust listen to the caller over the speaker. Press SCREEN. answer the call  Pick up the corded handset. Press TALK/FLASH.mute the call screen without answering Press MUTE.If you mute the call screen, the system continues taking the message: it just stops playing through the speaker.Up to four handsets at a time can screen calls. If a fifth handset tries to screen the call, the handset sounds an error tone and displays a System Busy message.
39Using the System While You're Away from HomeYou can also operate your answering system from any touch-tone phone. Before you can use this feature, you have to program a security code.Programming a security codeWith the phone in standby, open the menu and select Ans. Setup.When the phone prompts you to select a line, press LINE1 or LINE2, then select Security Code.Use the number keypad to enter a two-digit security code (01 to 99). Press OK when you’re finished.Remember to make a note of your new security code!Dialing in to your systemCall your telephone number and wait for the system to answer. (If your answering system is off, it will answer after about ten rings and sound a series of beeps instead of your greeting.)During the greeting (or beeps), press 0 and immediately enter your security code. (You have 3 tries to enter you security code: if you enter it wrong 3 times, the system hangs up and returns to standby.)The system announces the current time, the number of messages stored in memory, and a help prompt. Then it starts beeping intermittently to let you know it's waiting for your command. When you hear the intermittent  beeping, enter a command from the chart to the right.If you don't press any keys for 15 seconds, the phone will hang up and return to standby.1.2.3.1.2.3.4.0-1 Repeat message0-2 Play message0-3 Skip message0-4 Delete message0-5 Stop playback0-6 Turn the system on0-9 Turn the system off1-0 Hear help prompts0-1 Repeat message0-2 Play message0-3 Skip message0-4 Delete message0-5 Stop playback0-6 Turn the system on0-9 Turn the system off1-0 Hear help prompts
40Solving ProblemsIf you have any trouble with your phone, try these simple steps first. If you still have a question, call our Customer Care Line listed on the front cover.If… Try…No stations can make or receive calls.Checking the telephone cord connection.Disconnecting the base AC adapter. Wait a few minutes, then reconnect it.--One cordless handset can’t make or receive calls.Moving the handset closer to the base.Resetting the handset.--A station can make calls, but it won’t ring.Making sure the ringer is turned on.Making sure Do Not Disturb is turned off (see page 31).--I can't make or receive calls on line 2.Making sure line 2 is properly connected (see page 2).Checking the dial mode on line 2.Seeing if another station has activated Privacy Mode on line 2.Making sure you have subscribed to 2 separate lines from your phone company.----I can't conference line 1 and line 2 together.Seeing if another station has activated Privacy Mode on one of the lines (see page 29).-I can't make or receive calls while the power is out.Making sure you using the corded handset on the base.Checking the telephone cord connection.--A cordless handset's display won't turn on.Charging the battery for 15-20 hours.Checking the battery pack connection.--A cordless handset is not working.Charging the battery for 15-20 hours.Checking the battery pack connection.Resetting the handset.---A cordless handset says Unavailable.Moving the handset closer to the base.Seeing if another station has Privacy Mode on (see page 29). Making sure the base is plugged in.---
41If… Try…No stations will display any Caller ID information.Letting calls ring at least twice before answering.Seeing if the call was placed through a switchboard.Checking with your telephone service provider to make sure your Caller ID service is active.---I can't dial from the Caller ID list.Making sure you entered the correct area code. If you have to dial all 10 digits, you need to delete the area code (see Seven-digit Dialing on page 23). -Caller ID displays briefly and then clears.You may have to change the line mode. Contact customer service for more information.-I can’t transfer calls. Resetting all the handsets (see page 44). -I can’t get two cordless handsets to talk to the caller. Making sure both handsets are registered to this base.Making sure no station is in Privacy Mode (see page 29).--The phone keeps ringing if I answer on an extension.You may have to change the line mode. Contact customer service for more information.-I can't save a number to an existing phonebook entry.Seeing if the number is already in the phonebook.Seeing if that entry already has two phone numbers.--The answering system does not work.Making sure the answering system is turned on.Making sure the base AC adapter is not plugged into an that's controlled by a wall switch.--The answering system won't record messages.Making sure the Record Time is not set to Announce Only (see page 36).Deleting messages (the memory may be full).--A handset can't access the answering system.Making sure no other handset is using the system.Making sure the phone is in standby.--My outgoing message is gone.Seeing if there was a power failure. You may have to re-record your personal outgoing message.-I can’t hear the base speaker.Making sure call screening is turned on (see page 38).Changing the base speaker volume.--
42If… Try…Messages are incomplete.The incoming messages may be too long. Remind callers to leave a brief message.Deleting messages (the memory may be full).--The system keeps recording if I answer on an extension.You may have to change the line mode. Contact customer service for more information.-I can't register a handset.Seeing if there are 10 handsets registered to this base. Resetting the handset.--My alarm rings at the wrong time. Making sure the time is set correctly (see page 17).-My alarm won't ring on the right day(s).Making sure the days are selected (see page 33).Making sure the date is set correctly (see page 17).--A particular person can't call me.Making sure that number is not on your call block list (see page 31).-I deleted a number from the call block list, but the person is still blocked.If you add a number to the call block list through the phonebook, the phone saves both numbers from the phonebook entry. Check to see if this person is on the call block list with a second number.-Weak or Hard To Hear Audio If a caller’s voice sounds weak or soft, the signal might be blocked by large metal objects or walls; you might also be too far from the base, or the handset’s battery may be weak.Try moving around while you’re on a call or moving closer to the base to see if the sound gets louder.Make sure the handset’s battery is fully charged.Try adjusting the earpiece volume.Noise or Static On The LineInterference is the most common cause of noise or static on a cordless phone. Here are some common sources of interference:electrical appliances, especially microwave ovens computer equipment, especially wireless LAN equipment and DSL modems
43radio-based wireless devices,  such as room monitors, wireless controllers, or wireless headphones or speakerslarge florescent light fixtures (especially if they give off a buzzing noise)other services that use your phone line, like alarm systems, intercom systems, or broadband Internet serviceHere are some hints for when the static is...on 1 handset or in 1 location:  on all handsets or in all locations:Check nearby for one of the common interference sources.Try moving the handset away from a suspected source, or try moving the suspected source so it’s not between the handset and the base.Try moving closer to the base. There is always more noise at the edges of the base's range. If the handset displays an Out of Range message, you need to move closer to the base.---Check near the base for the source of interference.Try moving the base away from a suspected source, or turn off the source if possible.If the base has an adjustable antenna, try raising the antenna so it stands straight up.If you have any service that uses the phone line, you might need a filter (see below).----Installing a line lter or DSL lterSometimes, broadband Internet  services that use the telephone line can interfere with phones. One of these services−DSL−often causes static on telephones. A DSL filter or telephone line filter usually solves this problem. The technician who installed your DSL service might have Do you use a T-Coil hearing aid?If you have a hearing aid equipped with a telecoil (T-coil) feature, the interaction between the hearing aid and digital cordless phones can cause noise in the handset. If you have a T-coil hearing aid and you have problems with noise on the line, try turning on T-coil mode. Open the menu; select Handset Setup, then select T-coil. Using T-coil mode can shorten the handset’s talk time; make sure to watch the battery status and keep the battery charged.Do you use a T-Coil hearing aid?If you have a hearing aid equipped with a telecoil (T-coil) feature, the interaction between the hearing aid and digital cordless phones can cause noise in the handset. If you have a T-coil hearing aid and you have problems with noise on the line, try turning on T-coil mode. Open the menu; select Handset Setup, then select T-coil. Using T-coil mode can shorten the handset’s talk time; make sure to watch the battery status and keep the battery charged.DSL filterTelephone cordTelephone wall jackDSL filterTelephone cordTelephone wall jack
44left some filters for you; if not, call your DSL provider or look in any electronics store.Plug the DSL filter into the telephone wall jack and plug your phone’s base into the filter. Make a test call to make sure the noise is gone.Resetting and Registering HandsetsIf you are having trouble with a cordless handset or if you want to replace one, you need to clear the registration information from the base and the handset:Do you have the base the handset is registered to?Yes NoPress and hold END and # until the System Reset menu appears (about 5 seconds).Select Deregister HS. The display lists all registered handsets.Select the handset you want to reset.When the handset asks you to confirm, select Yes. (It may ask you twice, just to be sure.) The handset clears its information from the base and deletes it own link to the base.1.2.3.4.Press and hold END and # until the System Reset menu appears (about 5 seconds).Select Base Unavailable. When the handset asks you to confirm, select Yes. (It may ask you twice, just to be sure.) The handset deletes its own link without contacting the base. 1.2.3.When you reset a handset (or if you buy a new one), that handset displays a Handset Not Registered message. If you see this message on a handset, you need to register it to a base before you can use it.Registering a handsetOn the base, open the menu and select Register Handset. The display should say Handset Registering. On the handset you want to register, press and hold # until the handset display says Handset Registering (about 2 seconds). In about 30 seconds, the handset display should say Registration Complete. Press TALK/FLASH and make sure you get a dial tone.1.2.3.
45If... Try...you don't hear a dial tonethe display says Registration Failed --Making sure the handset is fully charged, then start over at step 1.To register a handset to a different base, see the section "Expanding Your Phone" in the user's guide for the other base.Handling Liquid DamageMoisture and liquid can damage your cordless phone.If the handset or base is exposed to moisture or liquid, but only the exterior plastic housing is affected, wipe off the liquid, and use as normal.If moisture or liquid has entered the plastic housing (i.e. liquid can be heard in the phone or liquid has entered the handset battery compartment or vent openings on the base), follow these steps:Handset BaseRemove the battery cover and disconnect the battery. Let dry for at least 3 days with the battery disconnected and the cover off for ventilation.After the handset dries, reconnect the battery pack and replace the cover. Recharge the battery fully (15-20 hours) before using.1.2.3.Disconnect the AC adapter to cut off the power.Disconnect the telephone cord.Let dry for at least 3 days before reconnecting.1.2.3.IMPORTANT: You must unplug the telephone line while recharging the battery pack to avoid charge interruption.CAUTION! DO NOT use a microwave oven to speed up the drying process. This will cause permanent damage to the handset, base and the microwave oven.
Important InformationTerms Used In This GuideAccessory HandsetAn extra handset that can register to and be used with an expandable phone base. All accessory handsets must be registered to a base.Base The main part of the phone. It connects to your phone line and lets you make and receive calls. Most bases also have a cradle to store a handset.CIDCW (CID on Call Waiting.) A service that shows CID for calls that come in during another call.Call Waiting A service that lets you receive calls while you are on another call.Caller ID  (Also called CID.) A service that shows the name and number of incoming callers.Charger A cradle that stores and charges a handset but doesn’t connect to the phone line. Cradle The part of the phone that stores a handset. While in a cradle, a handset is always in standby, and any keys are locked. During a call The station is currently on a call or has activated a dial tone.Handset 1) A cordless handset that you use to dial the phone and talk to callers.  2) A corded handset that attaches to a base with a coiled cord. In standby  The phone is inactive: there is no dial tone, no station is on a call or listening to messages.Line 1 and Line 2On a two-line jack, line 1 is connected to the inner pair of wires, and line 2 is connected to the outer pair of wires. If you want to switch the lines, contact your phone company.On single-line jacks, line 1 is connected to TEL LINE 1/2, and line 2 is connected to TEL LINE 2. You can switch Line 1 and Line 2 just by swapping the connectors.Off hook The phone is connected to an outside line: there is a dial tone or an ongoing call.Soft key A software-controlled button that can change its function to t the current operation.Station Any handset or the base.SpecicationsUse only the supplied AC adapters.Be sure to use the proper adapter for the base and any chargers.Do not place the power cord where it creates a trip hazard or where it could become chafed and create a re or electrical hazard.Do not place the base in direct sunlight or subject it to high temperatures.Battery InformationFully charged, the battery should provide about 10 hours of talk time and about 7 days of standby time. For best results, return the handset to the cradle after each call to keep it fully charged. Keep an eye on the battery status icon. When the battery gets too low, the handset shows a low battery alert. If you hear a strange beep during a call, check the display: if you see the low battery AC adapterBase ChargerPart number PS-0034 PS-0035Input voltage 120V AC, 60 Hz 120V AC, 60 HzOutput voltage 7.8V AC @ 450mA 8V AC @ 300mABattery packPart number BT-1018Capacity 500mAh, 2.4V DCAC adapterBase ChargerPart number PS-0034 PS-0035Input voltage 120V AC, 60 Hz 120V AC, 60 HzOutput voltage 7.8V AC @ 450mA 8V AC @ 300mABattery packPart number BT-1018Capacity 500mAh, 2.4V DC
alert, nish your conversation as quickly as possible and return the handset to the cradle. If the handset is in standby, none of the keys will operate.With normal use, the battery should last about one year. Replace the battery when the talk time becomes short even when the battery is charged. To buy a replacement battery, call the Parts Department listed on the front cover. Rechargeable Nickel-Metal-Hydride Battery WarningCAUTION! Risk of explosion if battery is replaced by an incorrect type! Dispose of used batteries according to the instructions. Do not open or mutilate the battery. Disconnect the battery before shipping this product.This equipment contains a rechargeable Nickel-Metal-Hydride battery. The rechargeable batteries contained in this equipment may explode if disposed of in a re. Nickel is a chemical known to state of California to cause cancer. Do not short-circuit the battery. Do not charge the rechargeable battery pack used in this equipment with in any charger other than the one designed to charge this battery pack as specied in the owner's manual. Using another charger may damage the battery pack or cause the battery pack to explode. Rechargeable Batteries Must Be Recycled or Disposed of Properly. Uniden works to reduce lead content in PVC coated cords in our products & accessories.Warning! The cords on this product and/or accessories contain lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.Compliance InformationFCC Part 68 informationThis equipment complies with Part 68 of the FCC rules & the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the phone company.An applicable Universal Service Order Codes (USOC) certication for the jacks used in this equipment is provided (i.e., RJ11C) in the packaging with each piece of approved terminal equipment. A plug & jack used to connect this equipment to the premises wiring & telephone network must comply with the applicable FCC Part 68 rules & requirements adopted by the ACTA. A compliant telephone cord & modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.The REN is used to determine the number of devices that may be connected to a phone line. Excessive RENs on a phone line may result in devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed ve (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the telephone provider. The REN for this product is part of the product identier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to le a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modications to maintain uninterrupted service.Please follow instructions for repairing, if any (e.g. battery replacement section); otherwise do not substitute or repair any parts of the device except as specied in this manual. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. This equipment is hearing aid compatible.If you experience trouble with this equipment, contact the manufacturer (see the cover of this manual for contact information) or an authorized agent. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. If your home has wired alarm equipment connected to a phone line, be sure that installing the system does not disable your alarm equipment. If you have questions about what will disable alarm equipment, contact your telephone company or a qualied installer.Any changes or modications to this product not expressly approved by the manufacturer or other party responsible for compliance could void your authority to operate this product.NOTICE: According to telephone company reports, AC electrical surges, typically resulting from lightning strikes, are very destructive to telephone equipment connected to AC power sources. To minimize damage from these types of surges, a surge arrestor is recommended.FCC Part 15 informationThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, & (2) This device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this phone. FCC PART 15.105(b): Note: This equipment has been tested & found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses & can radiate radio frequency energy and, if not installed & used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off & on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.This product complies with FCC radiation exposure limits under the following conditions: The base must be placed to allow a minimum of 20 cm (8 inches) between the antenna and all persons during normal operation. The base must not be collocated or operated in conjunction with any other antenna or transmitter. The handset is designed for body-worn operation and meets FCC RF exposure guidelines when used with any belt clip, carrying case, or other accessory supplied with this product. (All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines.) Third party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FCC RF exposure guidelines. Industry Canada (I.C.) NoticeTerminal equipmentNOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specications. This is conrmed by the registration number. The abbreviation IC before the registration number signies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specications were met. It does not imply that Industry Canada approved the equipment.NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.Radio equipmentThe term IC before the radio certication number only signies that Industry Canada technical specications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, & (2) this device must accept any interference, including interference that may cause undesired operation of the device. "Privacy of communications may not be ensured when using this telephone".One-year Limited WarrantyImportant: Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials & craftsmanship with only the limitations or exclusions set out below. WARRANTY DURATION: This warranty to the original user shall terminate & be of no further effect 12 months after the date of original retail sale. The warranty is invalid if the Product is (A) damaged or not maintained as reasonable or necessary, (B) modied, altered, or used as part of any conversion kits, subassemblies, or any congurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner's manual for this product. 
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit & return it to you without charge for parts, service, or any other cost (except shipping & handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE & ENTIRE WARRANTY PERTAINING TO THE PRODUCT & IS IN LIEU OF & EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.LEGAL REMEDIES: This warranty gives you specic legal rights, & you may also have other rights which vary from state to state. This warranty is void outside the United States of America & Canada. PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner's manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). Disconnect the battery from the Product & separately secure the battery in its own separate packaging within the shipping carton. The Product should include all parts & accessories originally packaged with the Product. Include evidence of original purchase & a note describing the defect that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to warrantor at:Uniden America Service 4700 Amon Carter Blvd. Fort Worth, TX 76155Uniden® is a registered trademark of Uniden America Corporation.Call waiting, CID, CIDCW, and Voice Mail are telephone line services. Your phone supports these services, but you have to arrange for them through your telephone provider. Contact your provider for details.The pictures in this manual are for example only. Your phone may not look exactly like the pictures.May be covered under one or more of the following U.S. patents:5,491,745  5,533,010  5,574,727  5,581,598  5,606,598  5,650,790  5,660,269  5,663,981  5,671,248 5,717,312  5,732,355  5,754,407  5,758,289  5,768,345  5,787,356  5,794,152  5,801,466  5,825,1615,864,619  5,893,034  5,912,968  5,915,227  5,929,598  5,930,720  5,960,358  5,987,330  6,044,281 6,070,082  6,076,052  6,125,277  6,253,088  6,314,278  6,321,068  6,418,209  6,618,015  6,714,6306,782,098  6,788,920  6,788,953  6,839,550  6,889,184  6,901,271  6,907,094  6,914,940  6,940,867 6,953,118  7,023,176  7,030,819  7,146,160  7,203,307  7,206,403  7,310,398  7,460,663Other patents pending.As an Energy Star® Partner, Uniden has determined that this product meets the Energy Star® guidelines for energy efciency. Energy Star® is a U.S. registered mark.As an Energy Star® Partner, Uniden has determined that this product meets the Energy Star® guidelines for energy efciency. Energy Star® is a U.S. registered mark.© 2009 Uniden America Corp.  Printed in Vietnam Ft. Worth, TX 76155  UNZZ01042BA(0)

Navigation menu