Ubiquiti PBE5AC Access Point User Manual PowerBeam PBE 5AC 620 Quick Start Guide

Ubiquiti Networks, Inc. Access Point PowerBeam PBE 5AC 620 Quick Start Guide

UNII-2 620 part 2 of 4

10. Attach the Stabilizer Brackets to the pole just beneath the area where the PowerBeam will be attached.Note: The pole‑bracket assembly can accommodate a Ø 38 - 101mm pole.a. Place one Stabilizer Bracket on each side of the pole.b. Insert the two M10x100 Bolts into the Stabilizer Brackets.c. Secure each bolt with one Serrated Flange Nut.50 N-m
11. Attach the pole‑bracket assembly to the pole:a. Slide the slot of each Pole Clamp over the corresponding M8x150 CarriageBolt.b. Tighten the serrated flange nuts of the bolts to secure the pole-bracket assembly to the pole.Proper slot orientation25 N-m
12. Lift the Dish Reflector and align the two lower Hex Head Bolts with the slots on the Lower Pole Bracket. Seat the bolts in the slots.13. Attach each arm of the Upper Pole Bracket to the Mounting Bracket using a Hex Head Bolt, Lock Washer, and Flat Washer.
14. Before adjusting the tilt angle, ensure that the six Hex Head Bolts are loose enough to allow movement.IMPORTANT: If you cannot spin the washers freely by hand, then loosen the Hex Head Bolts until you can.15. To adjust the tilt angle, turn the screw head of the elevation rod until the desired tilt is reached.16. Lock the alignment by tightening all six FlangeBolts to 25 N-m.
Note: Steps 17-20 are optional instructions for mounting the Gigabit PoE Adapter on a wall.17. Remove the wall‑mount bracket from the Gigabit PoE Adapter and position it at the desired location on the wall with the arrow pointing up.18. Use a pencil to mark the two holes on the wall.19. Attach the wall‑mount bracket to the wall using the appropriate fasteners (not included).20. Align the tabs of the Gigabit PoE Adapter with the slots of the wall‑mount bracket and slide the Gigabit PoE Adapterdown.*640-00136-05*640-00136-05
21. Connect the other end of the Ethernet cable from the PowerBeam to the Ethernet port labeled POE on the Gigabit PoEAdapter.22. Connect an Ethernet cable from your LAN or computer to the Ethernet port labeled LAN on the Gigabit PoE Adapter.23. Connect the Power Cord to the power port on the Gigabit PoE Adapter. Connect the other end of the Power Cord to a power outlet.
Accessing airOSVerify connectivity in the airOS Configuration Interface. 1. Make sure that your host system is connected via Ethernet to the PowerBeam. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.3. Launch your web browser and type https://192.168.1.20 in the address field. Press enter (PC) or return (Mac). 4. The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login.Note: For the Country setting, U.S. product versions are restricted to a choice of Canada, Puerto Rico, or the U.S. to ensure compliance with FCC/IC regulations. The airOS Configuration Interface will appear, allowing you to customize your settings as needed. For details, refer to the User Guide available at documentation.ubnt.com/airmax
Installer Compliance ResponsibilityDevices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements.Since Ubiquiti Networks equipment can be paired with a variety of antennas and cables, the Antenna and Output Power fields are provided to the professional installer to assist in meeting regulatory requirements.
SpecificationsPowerBeam ac PBE-5AC-620Dimensions 650 x 650 x 386 mm (25.6 x 25.6 x 15.2")Weight 6.4 kg (14.11 lb)Operating Frequency Worldwide: 5150 - 5875 MHz USA: 5150 - 5350, 5470 - 5850 MHzGain 29 dBiNetworking Interface (1) 10/100/1000 Ethernet PortEnclosure Outdoor UV Stabilized PlasticMax. Power Consumption 8.5WPower Supply 24V, 0.5A Gigabit PoE Supply (Included)Power Method Passive PoE (Pairs 4, 5+; 7, 8 Return)Wind Survivability 200 km/h (125 mph)Wind Loading 872 N @200 km/h (196 lbf @125 mph)Certications CE, FCC, ICMounting Pole Mounting Kit IncludedOperating Temperature -40 to 70° C (-40 to 158° F)Operating Humidity 5 to 95% NoncondensingShock and Vibrations ETSI300-019-1.4

Navigation menu