Ubiquiti PBE2ACN PowerBeam AC User Manual PowerBeam PBE 2AC 400 Gen2 Quick Start Guide

Ubiquiti Networks, Inc. PowerBeam AC PowerBeam PBE 2AC 400 Gen2 Quick Start Guide

UserManual.wiki >

PBE2ACN User Manual

Users Manual

2.4 GHz High-PerformanceairMAX® ac Bridge withDedicated Wi-Fi ManagementModel: PBE-2AC-400

IntroductionThank you for purchasing the Ubiquiti Networks®PowerBeam®AC . This Quick Start Guide is designed to guide you through installation and also includeswarranty terms.If you want to add a radome to enclose the Dish Reflector,UbiquitiNetworks offers the PowerBeam Radome, 400 mm,modelPBE-RAD-400 as an optional accessory. Product detailsare available on our website at www.ubnt.comPackage ContentsDish Reflector Antenna Feed Rear Housing2010100Dish Bracket Pole Clamp U-Bolt Flange Nuts (Qty. 2)2.4 GHz High-Performance airMAX® ac Bridge with Dedicated Wi-Fi ManagementModel: PBE-2AC-400-Gen2Gigabit PoE (24V, 0.5A) with Mounting BracketPower Cord Quick Start GuideTERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable™ is designed for outdoor installations. It is the customer’s responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements.

Installation Requirements• 13 mm wrench• Shielded Category 5 (or above) cabling with drain wire should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE.We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable• Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the PowerBeam and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground. To LANETH-SPETH-SPES-8-150WPBE-2AC-400

Hardware OverviewBottom ViewDish ReflectorCable DoorRear HousingTechnologyEthernet PortRelease Button SlotDish BracketRelease ButtonAlignment PinsReset ButtonAntenna FeedReset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the PowerBeam is already poweredon. Alternatively, the PowerBeam may be reset remotely via a Reset button located on the bottom of the Gigabit PoE adapter.Release Button After you assemble the PowerBeam, check the Release button; it should be fully engaged in the Release Button Slot of the Rear Housing. This ensures that the Antenna Feed is locked into place. If you need to remove the Antenna Feed, you must depress the Release button first.

LEDsPower The Power LED will light blue when the device is connected to a power source.Ethernet The Ethernet LED will light steady blue when an active Ethernet connection is made and flash when there is activity.Signal In airOS®, you can modify the threshold value for the wireless signal strength LEDs on the Wireless tab under Signal LED Thresholds. Each LED will light when the wireless signal strength is equal to or greater than the LED’s threshold value. The default threshold values for these LEDs are shown below:-65 dBm -73 dBm -80 dBm -94 dBm

Application ExamplesThe PowerBeam mounted outdoors with the Dish Reflector installed provides directional outdoor coverage (gain is reflector-dependent).The PowerBeam mounted outdoors without the Dish Reflector installed provides outdoor-to-indoor coverage using the 3 dBi Antenna Feed only.

Installation1. Align and insert the tabs of the Dish Bracket into the slots of the Dish Reflector. Rotate the Dish Bracket counter-clockwise until the tabs lock into place.20101002. Line up the Alignment Pins of the Rear Housing with the alignment holes of the Dish Bracket. Insert the pins and push until they lock intoplace.2010100

3. Push in the sides of the Cable Door and detach it from the Rear Housing.20100104. Attach the Antenna Feed:a. Insert the Antenna Feed into the Rear Housing, and push until it locks into place with a click. b. Lightly pull the Antenna Feed to ensure that it is locked into place and the Release button is fully engaged.Release ButtonBottom View

5. Connect the Ethernet cable:a. Connect an Ethernet cable to the Ethernet Port of the Antenna Feed. b. Re-attach the Cable Door to the Rear Housing.20100106. Slide the Pole Clamp onto the Dish Bracket.2010100

7. Insert the U-Bolt into the Pole Clamp and Dish Bracket. Secure each end of the U-Bolt with a Flange Nut.201010025 N · mNote: The mounting assembly can accommodate a Ø 32 - 56 mm pole.8. Optional: If you have the PowerBeam Radome (optional accessory), then align the arrows on the bottoms of the Radome and Dish Reflector so the Drain Holes on the Radome point downward. Snap the Radome onto the Dish Reflector.

Connect the power using one of the following options: • Using the included Gigabit PoE Adapter: Go to Connecting to the PoE Adapter.• Using a separate PoE switch: Connect the Ethernet cable from the PowerBeam’s Ethernet port to a PoE-enabled Ethernet port on the switch.WARNING: The switch port must comply with the power specifications listed in the Specifications section of this Quick Start Guide.Connecting to the PoE Adapter1. Connect the Ethernet cable from the PowerBeam’s Ethernet port to the POE port of the Gigabit PoE adapter.2. Connect an Ethernet cable from your LAN to the adapter’s LAN port. 3. Connect the Power Cord to the adapter’s power port. Connect the other end of the Power Cord to a power outlet.Mounting the PoE Adapter (Optional)1. Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes. 2. Pre-drill the holes if necessary, and secure the bracket using two fasteners (not included).3. Align the adapter’s slots with the tabs of the PoE Mounting Bracket, and then slide the adapterdown.

Accessing airOS via Wi-FiVerify connectivity in the airOS Configuration Interface. There are two methods, the U Mobile App and Web Portal. Both are available for 15 minutes immediately after you power on the PowerBeam. If necessary, you can power cycle the PowerBeam to re-enable its Wi-Fi. Proceed to the appropriate instructions:U Mobile App1. Download the U Mobile app from the AppStore (iOS) or Google Play™ (Android).2. Connect your device’s Wi-Fi to the PowerBeam SSIDnamed: PBE-2AC-400:<MAC Address>Note: Ensure that DHCP is enabled on yourWi-Fiadapter.3. Launch the app4. Tap the PowerBeam on the Connections scree

5. Tap Connect on the Login screen.6. Select your Country and tap Done.

7. Customize your settings as needed.*640-00213-03*640-00213-03

Web Portal1. Connect your device’s Wi-Fi to the PowerBeam SSIDnamed: PBE-2AC-400:<MAC Address>Note: Ensure that your Wi-Fi connection has DHCPenabled.2. Launch a web browser and go to: http://setup.ubnt.com3. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login.Note: The Country setting for U.S. product versions is restricted to a choice of Canada, Puerto Rico, or the U.S. to ensure compliance with FCC/IC regulations. The airOS Configuration Interface will appear, allowing you to customize your settings as needed. For additional details on the airOS Configuration Interface, refer to the User Guide available at www.ubnt.com/download/airmax

Installer Compliance ResponsibilityDevices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements.Since Ubiquiti Networks equipment can be paired with a variety of antennas and cables, the Output Power field is provided to the professional installer to assist in meeting regulatory requirements.

SpecificationsPBE-2AC-400Dimensions 420 x 420 x 289 mm (16.54 x 16.54 x 11.38")Weight (Mount Included) 1.795 kg (4.809 lb)Gain 18 dBiNetworking Interface (1) 10/100/1000 Ethernet PortEnclosure Outdoor UV Stabilized PlasticMax. Power Consumption 7.5WPower Supply 24V, 0.5A Gigabit PoE Adapter (Included)Power Method Passive PoE (Pairs 4, 5+; 7, 8 Return)Wind Survivability 200 km/h (125 mph)Wind Loading 342.5 N @ 200 km/h (77 lbf @ 125 mph)Certications CE, FCC, ICMounting Pole Mounting Kit IncludedOperating Temperature -40 to 70° C (-40 to 158° F)Operating Humidity 5 to 95% NoncondensingShock and Vibrations ETSI300-019-1.4Operating Frequency (MHz)Worldwide 2412 - 2472USA 2412 - 2462Management Radio (MHz)Worldwide 5150 - 5250USA U-NII-3: 5725 - 5850

Safety Notices1. Read, follow, and keep these instructions.2. Heed all warnings.3. Only use attachments/accessories specified by the manufacturer.WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet.a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire. b. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death.c. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment.d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection.e. Protective bonding must be installed in accordance with local national wiring rules and regulations.

Limited WarrantyUBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term. Warranty ConditionsThe above warranty does not apply if the Product:(I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks’ authorized representatives, or as approved by Ubiquiti Networks in writing;(II) has been painted, rebranded or physically modified in any way;(III) has been damaged due to errors or defects in cabling;(IV) has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident;(V) has been damaged or impaired as a result of using third party firmware;(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or(VII) has not been received by Ubiquiti within 30 days of issuance of the RMA.In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed.ReturnsNo Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS’ facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal. Information on the RMA process and obtaining an RMA number can be found at: www.ubnt.com/support/warranty

DisclaimerEXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyer’s selection of products (including the Products) for buyer’s application and/or failure of products (including the Products) to meet government or regulatory requirements.Limitation of LiabilityEXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

NoteSome countries, states and provinces do not allow exclusions of impliedwarranties or conditions, so the above exclusion may not apply to you.You may have other rights that vary from country to country, state tostate, or province to province. Some countries, states and provinces do notallow the exclusion or limitation of liability for incidental or consequentialdamages, so the above limitation may not apply to you. EXCEPT TOTHE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DONOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THEMANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANYSOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United NationsConvention on Contracts for the International Sale of Goods shall not applyto any transactions regarding the sale of the Products.ComplianceFCCChanges or modifications not expressly approved by the party responsiblefor compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions.1. This device may not cause harmful interference, and2. This device must accept any interference received, includinginterference that may cause undesired operation.This equipment has been tested and found to comply with the limits for aClass A digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interferencewhen the equipment is operated in a commercial environment. Thisequipment generates, uses, and can radiate radio frequency energy and,if not installed and used in accordance with the instruction manual, maycause harmful interference to radio communications. Operations of thisequipment in a residential area is likely to cause harmful interference inwhich case the user will be required to correct the interference at his ownexpense.This radio transmitter (FCC ID: SWX-PBE2ACN) has been approved byFCC to operate with the antenna types listed below with the maximumpermissible gain and required antenna impedance for each antenna typeindicated. Antenna types not included in this list, having a gain greaterthan the maximum gain indicated for that type, are strictly prohibited foruse with this device.Antenna Information: Dish antenna, Gain: 18 dBi

Industry CanadaCAN ICES-3(A)/NMB-3(A)This Class A digital apparatus complies with Canadian CAN ICES-003.To reduce potential radio interference to other users, the antennatype and its gain should be so chosen that the equivalent isotropicallyradiated power (e.i.r.p.) is not more than that permitted for successfulcommunication.This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions:1. This device may not cause interference, and2. This device must accept any interference, including interference thatmay cause undesired operation of the device.This radio transmitter (IC: 6545A-PBE2ACN has been approved byIndustry Canada to operate with the antenna types listed below with themaximum permissible gain and required antenna impedance for eachantenna type indicated. Antenna types not included in this list, having again greater than the maximum gain indicated for that type, are strictlyprohibited for use with this device.Antenna Information: Dish antenna, Gain: 18 dBiCAN ICES-3(A)/NMB-3(A)Cet appareil numérique de la classe A est conforme à la norme NMB-003du Canada.Pour réduire le risque d’interférence aux autres utilisateurs, le typed’antenne et son gain doivent être choisies de façon que la puissanceisotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessairepour une communication réussie.Cet appareil est conforme à la norme RSS Industrie Canada exempts delicence norme(s). Son fonctionnement est soumis aux deux conditionssuivantes:1. Cet appareil ne peut pas provoquer d’interférences et2. Cet appareil doit accepter toute interférence, y compris lesinterférences qui peuvent causer un mauvais fonctionnement dudispositif.Cet émetteur radio (IC: 6545A-PBE2ACN) a été approuvée par IndustrieCanada pour l’exploitation avec l’antenne types énumérés ci-dessous avecle gain maximal admissible et requis l’impédance de l’antenne pour chaquetype d’antenne indiqué. Types d’antenne non inclus dans cette liste, ayantun gain supérieur au gain maximal indiqué pour ce type, sont strictementinterdits pour une utilisation avec cet appareil.Informations d’antenne: Antenne parabolique, Gain: 18 dBi

RF Exposure WarningThe antennas used for this transmitter must be installed to provide aseparation distance of at least 28 cm from all persons and must not be lo-cated or operating in conjunction with any other antenna or transmitter.Les antennes utilisées pour ce transmetteur doivent être installé enconsidérant une distance de séparation de toute personnes d’au moins28cm et ne doivent pas être localisé ou utilisé en conflit avec tout autreantenne ou transmetteur.Australia and New ZealandWarning: This is a Class A product. In a domestic environment thisproduct may cause radio interference in which case the user maybe required to take adequate measures.CE MarkingCE marking on this product represents the product is in compliance with alldirectives that are applicable to it.

RoHS/WEEE Compliance StatementEnglishEuropean Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.DeutschDie Europäische Richtlinie 2012/19/EU verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.

EspañolLa Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.FrançaisLa directive européenne 2012/19/UE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.ItalianoLa direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.

Declaration of Conformityбългарски [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че този тип радиосъоръжение това устройство UBIQUITI NETWORKS е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.com/complianceHrvatski [Croatian] UBIQUITI NETWORKS ovime izjavljuje da je radijska oprema tipa ovaj UBIQUITI NETWORKS uređaj u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: www.ubnt.com/complianceČeština [Czech] Tímto UBIQUITI NETWORKS prohlašuje, že typ rádiového zařízení že toto UBIQUITI NETWORKS zařízení je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: www.ubnt.com/complianceDansk [Danish] Hermed erklærer UBIQUITI NETWORKS., at radioudstyrstypen denne UBIQUITI NETWORKS enhed er i overensstemmelse med direktiv 2014/53/EU. EU‑overensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse: www.ubnt.com/complianceNederlands [Dutch] Hierbij verklaar ik, UBIQUITI NETWORKS, dat het type radioapparatuur UBIQUITI NETWORKS apparaat conform is met Richtlijn 2014/53/EU. De volledige tekst van de EU‑conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: www.ubnt.com/complianceEnglish Hereby, UBIQUITI NETWORKS declares that the radio equipment type this UBIQUITI NETWORKS device is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.ubnt.com/complianceEesti keel [Estonian] Käesolevaga deklareerib UBIQUITI NETWORKS, et käesolev raadioseadme tüüp antud UBIQUITI NETWORKS seade vastab direktiivi 2014/53/EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: www.ubnt.com/complianceSuomi [Finnish] UBIQUITI NETWORKS vakuuttaa, että radiolaitetyyppi että tämä UBIQUITI NETWORKS laite on direktiivin 2014/53/EU mukainen. EU‑vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.ubnt.com/complianceFrançais [French] Le soussigné, UBIQUITI NETWORKS, déclare que l’équipement radioélectrique du type l’appareil UBIQUITI NETWORKS est conforme à la directive 2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l’adresse internet suivante: www.ubnt.com/complianceDeutsch [German] Hiermit erklärt UBIQUITI NETWORKS, dass der Funkanlagentyp dieses UBIQUITI NETWORKS Gerät der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EU‑Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: www.ubnt.com/complianceΕλληνικά [Greek] Με την παρούσα ο/η UBIQUITI NETWORKS, δηλώνει ότι ο ραδιοεξοπλισμός αυτή η συσκευή UBIQUITI NETWORKS πληροί την οδηγία 2014/53/ΕΕ. Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: www.ubnt.com/complianceMagyar [Hungarian] UBIQUITI NETWORKS igazolja, hogy a UBIQUITI NETWORKS készülék típusú rádióberendezés megfelel a 2014/53/EU irányelvnek. Az EU‑megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: www.ubnt.com/complianceÍslenska [Icelandic] Hér með lýsir UBIQUITI NETWORKS yfir því að þetta UBIQUITI NETWORKS tæki er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 2014/53/EU. Fullur texti ESB samræmisyfirlýsing er að finna á eftirfarandi netfangi: www.ubnt.com/complianceItaliano [Italian] Il fabbricante, UBIQUITI NETWORKS, dichiara che il tipo di apparecchiatura radio questo dispositivo UBIQUITI NETWORKS èconforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.com/compliance

Latvių kalba [Latvian] Ar šo UBIQUITI NETWORKS deklarē, ka radioiekārta ka UBIQUITI NETWORKS ierīce atbilst Direktīvai 2014/53/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: www.ubnt.com/complianceLietuvių kalba [Lithuanian] Aš, UBIQUITI NETWORKS, patvirtinu, kad radijo įrenginių tipas šis UBIQUITI NETWORKS įrenginys atitinka Direktyvą 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu: www.ubnt.com/complianceMalti [Maltese] B’dan, UBIQUITI NETWORKS, niddikjara li dan it‑tip ta’ tagħmir tar‑radju dan il‑mezz UBIQUITI NETWORKS huwa konformi mad‑Direttiva 2014/53/UE. Id‑dikjarazzjoni tal‑konformità tista’ tiġi kkonsultata minn www.ubnt.com/complianceNorsk [Norwegian] UBIQUITI NETWORKS erklærer herved at utstyret denne UBIQUITI NETWORKS enheten er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 2014/53/EU. Den fulle teksten til EU‑samsvarserklæringen er tilgjengelig på følgende internettadresse: www.ubnt.com/compliancePolski [Polish] UBIQUITI NETWORKS niniejszym oświadcza, że typ urządzenia radiowego urządzenie UBIQUITI NETWORKS, jest zgodny z dyrektywą 2014/53/UE. Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym: www.ubnt.com/compliancePortuguês [Portuguese] O(a) abaixo assinado(a) UBIQUITI NETWORKS declara que o presente tipo de equipamento de rádio este dispositivo UBIQUITI NETWORKS está em conformidade com a Diretiva 2014/53/UE. O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: www.ubnt.com/complianceRomână [Romanian] Prin prezenta, UBIQUITI NETWORKS declară că tipul de echipamente radio acest dispozitiv UBIQUITI NETWORKS este în conformitate cu Directiva 2014/53/UE. Textul integral al declarației UE de conformitate este disponibil la următoarea adresă internet: www.ubnt.com/complianceSlovenčina [Slovak] UBIQUITI NETWORKS týmto vyhlasuje, že rádiové zariadenie typu toto UBIQUITI NETWORKS zariadenie je v súlade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: www.ubnt.com/complianceSlovenščina [Slovenian] UBIQUITI NETWORKS potrjuje, da je tip radijske opreme ta naprava UBIQUITI NETWORKS skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.ubnt.com/complianceEspañol [Spanish] Por la presente, UBIQUITI NETWORKS declara que el tipo de equipo radioeléctrico este dispositivo UBIQUITI NETWORKS es conforme con la Directiva 2014/53/UE. El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: www.ubnt.com/complianceSvenska [Swedish] Härmed försäkrar UBIQUITI NETWORKS att denna typ av radioutrustning denna UBIQUITI NETWORKS enhet överensstämmer med direktiv 2014/53/EU. Den fullständiga texten till EU‑försäkran om överensstämmelse finns på följande webbadress: www.ubnt.com/complianceOnline ResourcesSupport help.ubnt.comCommunity community.ubnt.comDownloads downloads.ubnt.com

Navigation menu