Ubiquiti LBE5ACG2 LBE-5AC-Gen2, LBE-5AC-Omni-Gen2 User Manual LiteBeam LBE 5AC Gen2 Quick Start Guide
Ubiquiti Networks, Inc. LBE-5AC-Gen2, LBE-5AC-Omni-Gen2 LiteBeam LBE 5AC Gen2 Quick Start Guide
Ubiquiti >
Contents
- 1. Quick Start Guide_Part 1
- 2. Quick Start Guide_Part 2
- 3. Quick Start Guide_Part 3
- 4. Quick Start Guide_Part 4
Quick Start Guide_Part 3
![5. Take one end of an Ethernet cable and push it through the rubber housing on the Port Cover and connect it to the Ethernet Port.6. Reattach the Port Cover to the Feed Receiver by turning it clockwise until it is secure.](https://usermanual.wiki/Ubiquiti/LBE5ACG2.Quick-Start-Guide-Part-3/User-Guide-3312372-Page-1.png)
![Pole Mounting1. Attach the Elevation Mount to the Feed Receiver by lining up the notches with the pins on the FeedReceiver and pressing forward until the Elevation Mount snaps on.2. Open the Metal Strap and feed it through the slot of the AzimuthMount.](https://usermanual.wiki/Ubiquiti/LBE5ACG2.Quick-Start-Guide-Part-3/User-Guide-3312372-Page-2.png)
![3. Wrap the Metal Strap around the pole. Use a 7 mm socket wrench or screwdriver to turn the screw clockwise and securely fasten the strap to the pole.4. Attach the Elevation Mount to the Azimuth Mount as shown below. Do not tighten the Wingnuts completely until the LiteBeam assembly has been adjusted and aimed properly.WingnutWingnut](https://usermanual.wiki/Ubiquiti/LBE5ACG2.Quick-Start-Guide-Part-3/User-Guide-3312372-Page-3.png)
![5. Aim the Antenna Feed toward the other end of the wireless link. Use the bubble level on the back of the Feed Receiver to ensure proper level alignment.6. Lock the aim by hand‑tightening the Wingnuts clockwise on both the Elevation Mount and the Azimuth Mount.](https://usermanual.wiki/Ubiquiti/LBE5ACG2.Quick-Start-Guide-Part-3/User-Guide-3312372-Page-4.png)
![Connecting Power1. Connect the Ethernet cable from the LiteBeam AC to the POE port on the Power Adapter.2. Connect an Ethernet cable from your LAN to the LAN port on the Power Adapter.3. Connect the Power Cord to the Power Adapter, and then plug the Power Cord to a power outlet.Mounting the PoE Adapter (Optional)1. Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes. 2. Pre‑drill the holes if necessary, and secure the bracket using two fasteners (not included).3. Align the adapter’s slots with the tabs of the PoE Mounting Bracket, and then slide the adapterdown.*640-00276-03*640-00276-03](https://usermanual.wiki/Ubiquiti/LBE5ACG2.Quick-Start-Guide-Part-3/User-Guide-3312372-Page-5.png)
![Accessing airOS via Wi‑FiVerify connectivity in the airOS Configuration Interface. There are two methods, the U Mobile App and Web Portal. Both are available for 15 minutes immediately after you power on the device. If necessary, you can power cycle the LiteBeam AC to re‑enable its Wi‑Fi.Proceed to the appropriate instructions:U Mobile App1. Download the U Mobile app from the AppStore (iOS) or Google Play™ (Android).2. Connect your device’s Wi‑Fi to the LiteBeam AC SSID named: LBE-5AC-Gen2:<MAC Address>Note: Ensure that DHCP is enabled on your Wi‑Fiadapter.3. Launch the app.4. Tap the LiteBeam 5AC on the Connections screen.LiteBeam 5AC Gen 2LBE-5AC-Gen2192.168.1.20](https://usermanual.wiki/Ubiquiti/LBE5ACG2.Quick-Start-Guide-Part-3/User-Guide-3312372-Page-6.png)