Ubiquiti AF5XHD Digital Transmission Radio User Manual airFiber AF 5XHD Quick Start Guide

Ubiquiti Networks, Inc. Digital Transmission Radio airFiber AF 5XHD Quick Start Guide

UserManual.wiki >

AF5XHD User Manual

Quick Start Guide

5 GHz Carrier Radio with LTU TechnologyModel: AF-5XHDDATAMGMTGPSLINKDATAMGMTGPSLINK

IntroductionThank you for purchasing the Ubiquiti Networks® airFiber® AF-5XHD. This Quick Start Guide is designed to guide you through installation. Warranty terms, safety notices, and compliance information are in the airFiberAF-5XHD User Guide, available at: www.ubnt.com/download/airfiberPackage ContentsairFiber AF-5XHD GPS Antenna Mount External GPS AntennaMetal Strap Cable Ties (Qty. 2)Universal Bracket5 GHz Carrier Radio with LTU TechnologyModel: AF-5XHDDATAMGMTGPSLINKDATAMGMTGPSLINKGigabit PoE (24V, 1A) with Mounting Bracket Power Cord Quick Start GuideTERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable™ is designed for outdoor installations. It is the professional installer’s responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements.

Antenna CompatibilityThe airFiber AF-5XHD radio is designed for use with the following airFiber X antenna models:• AF-5G23-S45• AF-5G30-S45• AF-5G34-S45The AF-5XHD can also operate with the following RocketDish™ antenna models:• RD-5G30*• RD-5G34** Requires Universal Bracket (included) or AF-5G-OMT-S45 Conversion Kit (not included).Installation Requirements• Clear line of sight between airFiber radios• Clear view of the sky for proper GPS operation• Vertical mounting orientation• Mounting point:• At least 1 m below the highest point on the structure• For tower installations, at least 3 m below the top of thetower• Ground wires – min. 10 AWG (5 mm2) and max. length: 1m. Asa safety precaution, ground the airFiber radio to grounded masts, poles, towers, or grounding bars. WARNING: Failure to properly ground your airFiber radio will void your warranty.• (Recommended) 2 Outdoor Gigabit PoE surge protectorsNote: For guidelines about grounding and lightning protection, follow your local electrical regulatory codes.• Outdoor, shielded Category 6 (or above) cabling and shielded RJ-45 connectors are required for all wired Ethernet connections.

Hardware OverviewPort CoverLEDPanelConnects toExternal GPS Antenna Chain 1: Connects to- 45° on airFiber AntennaChain 0: Connects to+ 45° on airFiber Antenna

PortsReset ButtonManagement PortData PortManagement Port 10/100/1000 Mbps, secured Ethernet port for configuration. In-Band Management is enabled by default in the airFiber Configuration Interface. When In-Band Management is disabled, the MGMT port is the only port that can monitor, configure, and/or update firmware. This port can also be used to provide redundant PoE power.Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is already poweredon.Data Port Gigabit PoE port for handling all user traffic and powering the device.

LEDsSignal LEDsSignal 4 LED will light blue when on.Signal 3 LED will light green when on.Signal 2 LED will light yellow when on.Signal 1 LED will light red when on.Bootup to airOS When powering on, the Power, GPS, LINK, and Signal 1-4 LEDs light on. Once the CPU code takes over, the GPS, LINK, and Signal 1-3 LEDs turn off. Signal 4 LED remains on to indicate the boot sequence is underway.Initializing airFiber Software When the airFiber application begins to boot under airOS, the Signal 4 LED goes from solidly on to a 2.5 Hz flash. This continues until the AF-5XHD is fully booted.Signal Level Once fully booted, the Signal 1-4 LEDs act as a bar graph showing how close the AF-5XHD is to ideal aiming. This is auto-scaled based on the link range, the antenna gains, and the configured TX power of the remote AF-5XHD. Each Signal LED has three possible states: On, Flashing, and Off. All Signal LEDs would be solidly on in an ideal link. If the link has a 1 dB loss, the Signal4 LED will flash; a 2 dB loss and the Signal 4 LED will turn off. The full bar graph LED states are shown below.dB loss 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -131F000000000000111F000000000011111FF00000001111111111FFF00 = Off, 1 = On, F = Flashing

Additional LEDsLED State StatusLINKOff RF OffShort Flash* SyncingNormal Flash* BeaconingLong Flash* RegisteringOn OperationalGPSOff No GPS SynchronizationNormal Flash* Non-Operational (Weak Signal) On Operational (Strong Signal)MGMTOff No Ethernet LinkOn Ethernet Link EstablishedRandom Flash Ethernet ActivityDATAOff No Ethernet LinkOn Ethernet Link EstablishedRandom Flash Ethernet Activity Off No PowerOn Powered On* Short Flash (1:3 on/off cycle) Normal Flash (1:1 on/off cycle) Long Flash (3:1 on/off cycle)*640-00338-01*640-00338-01

Installation OverviewWe recommend that you configure your paired AF-5XHD radios before site installation. The overview below summarizes the installation procedure, and the subsequent sections provide detailed installation information. • Connect the airFiber PoE Adapter to the DATA port, and connect your computer to the MGMTport.• Configure the AF-5XHD.• Install a ground wire and mount the AF-5XHD on an airFiberX or RocketDish antenna.• At the installation site, install the airFiber X or RocketDish antenna with the mounted AF-5XHD radio (see the antenna’s Quick Start Guide for installation instructions).• Secure the ground wire and mount the GPS antenna.• Establish and optimize the RF link.Connecting Power over Ethernet1. Lift the release latch on the bottom of the AF-5XHD and slide the Port Cover off.

2. Connect an Ethernet cable to the DATA port.3. Connect the Ethernet cable from the DATA port of the AF-5XHD to the POE port of the adapter.WARNING: Use only the included adapter, model GP‑H240‑100G‑WH‑03. Failure to do so can damage the unit and void the product warranty.4. Connect the Power Cord to the adapter’s power port. Connect the other end of the Power Cord to a poweroutlet.

airFiber ConfigurationThe instructions in this section explain how to access the airFiber Configuration Interface and configure the following settings: • Wireless Mode Configure one AF-5XHD as the AP and the other as the CPE.• Frequency Setting The operating Frequency must be the same on both the AP and the CPE.1. Connect an Ethernet cable from your computer to the MGMT port on the AF-5XHD.2. Configure the Ethernet adapter on your computer with a static IP address on the 192.168.1.x subnet.3. Launch your web browser. Type http://192.168.1.20 in the address field and press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login.Note: U.S. product versions are locked to the U.S. Country Code to ensure compliance with FCC regulations. 5. Click the Wireless tab.6. Configure the Basic Wireless Settings:a. For one AF-5XHD, select AP PTP as the Wireless Mode. For the other AF-5XHD, select CPE PTP as the Wireless Mode.b. Enter a name in the SSID field. This should be the same on both the AP and the CPE.c. Select USA for the Country code to ensure compliance with FCC regulations.d. Change the Distance Scale to be larger than the anticipated distance between the AP and CPE.e. If needed, change the Channel Width, Frequency, Output Power (EIRP), Antenna Gain, and Maximum TX Modulation settings. The Channel Width and Frequency should be the same on both the AP and the CPE.7. Configure the Wireless Security: a. Select WPA2‑AES for the Security mode.b. Select PSK for the WPA Authentication mode.c. In the WPA Preshared Key field, enter a combination of alphanumeric characters (0-9, A-Z, or a-z).Note: Currently only ASCII mode is supported.8. Configure the Advanced wireless settings:a. Enter the Duty Cycle on the AP.b. Enter the Frame Length on both the AP and the CPE. This should be the same on both the AP and the CPE.9. Click Save Changes.

10. Configure each airFiber radio with a unique IP address for the DATA port:a. Click the Network tab.b. For both the Data LAN Address and Management IP Address options: - DHCP Keep the default, DHCP, to use DHCP reservation on your router to assign a unique IPAddress. - Static Change the IP Address, Netmask, and other settings to make them compatible with your network.c. Enable the Ethernet Carrier Drop settings if needed.d. Click Save Changes.Repeat the instructions in the airFiber Configuration section on the other AF-5XHD radio.For details on the airFiber Configuration Interface, refer to the airFiber AF-5XHD User Guide, available at: www.ubnt.com/download/airfiber

Hardware InstallationInstall a Ground Wire1. Remove the nut from the Ground Bonding Point located on the back of the AF-5XHD.Ground Bonding Point2. Attach a ground wire (min. 10 AWG or 5 mm2) to the lug and replace the nut to secure the wire.3. At the installation site, secure the other end of the ground wire to a grounded mast, pole, tower, or grounding bar.WARNING: Failure to properly ground your airFiber radio will void your warranty.Note: The ground wire should be as short as possible and no longer than one meter in length.

Mount to an airFiber X AntennaFollow the instructions in this section to mount the AF-5XHD to an airFiber X antenna or to a RocketDish antenna equipped with the AF-5G-OMT-S45 Conversion Kit.Note: To mount the AF-5XHD to a RocketDish using the included Universal Bracket, see the Mount to a RocketDish Antenna section.The airFiber X antenna AF-5G23-S45 is shown in this section:1. Attach the airFiber X radio to the antenna by aligning the four tabs on the back of the radio with the slots of the radio mount. Then slide the radio down to lock it into place.

2. Attach the RF connectors to the radio in this combination: +45° to Chain0 and -45° to Chain 1. Then slide the jackets over the RF connectors to protect them.3. Attach the external GPS antenna (included with the radio) to the RF connector labeled GPS on the radio.

4. Attach the Protective Shroud by sliding it down over the radio until it locks into the radio mount.

Mount to a RocketDish AntennaNote: If you are mounting the AF-5XHD on a RocketDish equipped with the AF-5G-OMT-S45 Conversion Kit, the Universal Bracket is not needed. Refer instead to the Mount to an airFiber X Antenna section for instructions.The RocketDish RD-5G30 antenna is shown in this section:1. Position the Universal Bracket over the back of the AF-5XHD with the bracket clips over the AF-5XHD mounting tabs.2. Push the bracket onto the AF-5XHD until it locks in place.3. Attach the AF-5XHD to the RocketDish mounting bracket. a. Align the mounting tabs on the Universal Bracket with the RocketDish mounting bracket.b. Slide the AF-5XHD down to lock it into place.

Mount the External GPS AntennaLocate a mounting point that has a clear view to the sky, and is above and as far away as possible from the AF-5XHD.1. Attach the GPS Antenna Mount to the pole using the metal strap, or attach it to a wall using the appropriate fasteners (notincluded).2. Place the External GPS Antenna on the mount.3. Secure the cable of the External GPS Antenna to the mount with a Cable Tie.

Connecting Power over Ethernet1. Lift the release latch on the bottom of the AF-5XHD and slide the Port Cover off. 2. Connect an outdoor, shielded Ethernet cable to the DATAport.3. Connect the Ethernet cable from the DATA port of the AF-5XHD to the POE port of the adapter.WARNING: Use only the included adapter, model GP‑H240‑100G‑WH‑03. Failure to do so can damage the unit and void the product warranty.

4. Connect an Ethernet cable from your LAN to the adapter’s LAN port.5. Connect the Power Cord to the adapter’s power port. Connect the other end of the Power Cord to a power outlet.Mount the PoE Adapter (Optional)1. Remove the Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes.2. Pre-drill the holes if necessary, and secure the bracket using two fasteners (not included). 3. Align the adapter’s slots with the tabs of the Mounting Bracket, and then slide the adapter down.Surge ProtectionFor added protection, install two surge suppressors, such as the Ubiquiti Ethernet Surge Protector, model ETH-SP, at the end of each link. Install the first surge protector within one meter of the airFiber DATA port, and install the second surge protector at the ingress point of the location housing the wired network equipment.

Ground to Pole, Tower,or Grounding Block:Max. 1 m from AF-5XHDMax. 1 mairFiberPoE AdapterEdgeRouter™Power SourceETH-SPGPS AntennaETH-SPAF-5XHDMounted onAF-5G23-S45AlignmentTips• To accurately align the airFiber radios for best performance, you MUST align only one end of the link at a time.• You may need to use additional hardware to compensate for issues such as the improper orientation of a mounting pole or significant elevation differences between airFiber radios.

Establishing a LinkAdjust the positions of the AP and the CPE to establish a link. The following section features the airFiber X antenna, AF-5G23-S45:Note: The AP must be aimed first at the CPE because the CPE does not transmit any RF signal until it detects transmissions from the AP.1. AP Visually aim the AP at the CPE. To adjust the AP’s position, adjust the azimuth and the elevation.Adjust the azimuth:a. Loosen the two Flange Nuts on the U-Bolt.b. Rotate the antenna to point towards the other end of the link.c. Tighten the two Flange Nuts.The elevation angle may be adjusted ±15°. Adjust the elevation angle:d. Loosen the four Hex Bolts on both sides of the antenna.e. Pivot the antenna to the desired elevation.f. Tighten the four Hex Bolts.

Note: Do NOT make simultaneous adjustments on the AP and CPE.2. CPE Visually aim the CPE at the AP. To adjust the CPE’s position, adjust the azimuth and elevation as described in step 1.3. Check to see if a link is established. Ensure that the LINK LED is solidly lit green and the Signal LEDs of the CPE are displaying signal levels.4. CPE Aim the CPE at the AP to achieve the strongest signal level on the AP.Note: Refer to the Signal LEDs section for details on the signal values.Note: Maximum signal strength can best be achieved by iteratively sweeping through both azimuth and elevation.

5. AP Aim the AP at the CPE to achieve the strongest signal level on the CPE.6. Repeat steps 4 and 5 until you achieve an optimal link, with all four Signal LEDs solidly lit. This ensures the best possible data rate between the airFiber radios.7. Lock the alignment on both airFiber antennas by tightening all the nuts and bolts.8. Observe the Signal LEDs of each airFiber radio to ensure that the values remain constant while tightening the nuts and bolts. If any LED value changes during the locking process, loosen the nuts and bolts, finalize the alignment of each airFiber antenna again, and retighten the nuts and bolts.Installer Compliance ResponsibilityDevices must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within local country regulatory requirements.The Frequency, Output Power, Antenna Gain, and Cable Loss fields are provided to the professional installer to assist in meeting regulatory requirements.

SpecificationsAF-5XHDDimensions 224 x 82 x 48 mm (8.82 x 3.23 x 1.89")Weight 0.35 kg (0.77 lb)RF Connectors (2) RP-SMA Weatherproof (CH0, CH1)(1) SMA Weatherproof (GPS)GPS Antenna External, Magnetic BasePower Supply 24V, 1A PoE Gigabit Adapter (Included)Power Method Passive Power over Ethernet Networking InterfaceData PortManagement Port(1) 10/100/1000 Ethernet Port(1) 10/100/1000 Ethernet PortBluetooth Bluetooth v4.0Mounting Rocket Mount CompatibleGPS Pole Mount (Included)Operating Temperature -40 to 55° C (-40 to 131° F)Certications FCC Part 15.407CE EN 302502 v1.2.1, EN 301 893 v1.7.1 SystemMaximum Throughput 1 GbpsEncryption 128-bit and 256-bit AESOS airOS 8Wireless Modes AP/CPERadioOperating Frequency 5150-5925 MHz (Depends on Regulatory Region)Max. Conducted TX Power26 dBm (Depends on Regulatory Region)Frequency Accuracy ± 2.5 ppm without GPS Synchronization± 0.2 ppm with GPS SynchronizationChannel Bandwidth 10/20/30/40/50/60/80/100 MHz Selectable Programmable Uplink and Downlink Duty Cycles

Installer Compliance ResponsibilityDevices must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within local country regulatory requirements.FCCChanges or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This radio transmitter (FCC: SWX-AF5XHD) has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.• Omni antenna, gain: Up to 13 dBi• Sector antenna, gain: Up to 22 dBi• Dish antenna, gain: Up to 34 dBiDFS Regulatory RegionsOperation in DFS regulatory regions requires an antenna with minimum gain of 23 dBi.

ISED CanadaCAN ICES-3(B)/NMB-3(B)To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.This radio transmitter (IC: 6545A-AF5XHD) has been approved by ISED Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.• Omni antenna, gain: Up to 13 dBi• Sector antenna, gain: Up to 22 dBi• Dish antenna, gain: Up to 34 dBiCAN ICES-3(B)/NMB-3(B)Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie. Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :1. Cet appareil ne peut pas provoquer d’interférences et 2. Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.Le présent émetteur radio (IC: 6545A-AF5XHD) a été approuvé par ISDE Canada pour l’exploitation avec l’antenne types énumérés ci-dessous avec le gain maximal admissible et requis l’impédance de l’antenne pour chaque type d’antenne indiqué. Types d’antenne non inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type, sont strictement interdits pour une utilisation avec cet appareil.• Antenne omnidirectionnelle, gain: Jusqu’à 13 dBi• Antenne secteur, gain: Jusqu’à 22 dBi• Antenne parabolique, gain: Jusqu’à 34 dBi

RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 126 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter.Les antennes utilisées pour ce transmetteur doivent être installé en considérant une distance de séparation de toute personnes d’au moins 126cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre antenne ou transmetteur.Australia and New ZealandWarning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.CE MarkingCE marking on this product represents the product is in compliance with all directives that are applicable to it.RoHS/WEEE Compliance StatementEnglishEuropean Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

DeutschDie Europäische Richtlinie 2012/19/EU verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.EspañolLa Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.FrançaisLa directive européenne 2012/19/UE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.

ItalianoLa direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.Declaration of Conformityбългарски [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че този тип радиосъоръжение AF-5XHD е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.com/complianceHrvatski [Croatian] UBIQUITI NETWORKS ovime izjavljuje da je radijska oprema tipa AF-5XHD u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: www.ubnt.com/complianceČeština [Czech] Tímto UBIQUITI NETWORKS prohlašuje, že typ rádiového zařízení AF-5XHD je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: www.ubnt.com/complianceDansk [Danish] Hermed erklærer UBIQUITI NETWORKS, at radioudstyrstypen AF-5XHD er i overensstemmelse med direktiv 2014/53/EU. EU-overensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse: www.ubnt.com/complianceNederlands [Dutch] Hierbij verklaar ik, UBIQUITI NETWORKS, dat het type radioapparatuur AF-5XHD conform is met Richtlijn 2014/53/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: www.ubnt.com/complianceEnglish Hereby, UBIQUITI NETWORKS declares that the radio equipment type AF-5XHD is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.ubnt.com/complianceEesti keel [Estonian] Käesolevaga deklareerib UBIQUITI NETWORKS, et käesolev raadioseadme tüüp AF-5XHD vastab direktiivi 2014/53/EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: www.ubnt.com/complianceSuomi [Finnish] UBIQUITI NETWORKS vakuuttaa, että radiolaitetyyppi AF-5XHD on direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.ubnt.com/complianceFrançais [French] Le soussigné, UBIQUITI NETWORKS, déclare que l’équipement radioélectrique du type AF-5XHD est conforme à la directive 2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l’adresse internet suivante: www.ubnt.com/complianceDeutsch [German] Hiermit erklärt UBIQUITI NETWORKS, dass der Funkanlagentyp AF-5XHD der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: www.ubnt.com/complianceΕλληνικά [Greek] Με την παρούσα ο/η UBIQUITI NETWORKS, δηλώνει ότι ο ραδιοεξοπλισμός AF-5XHD πληροί την οδηγία 2014/53/ΕΕ. Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: www.ubnt.com/compliance

Magyar [Hungarian] UBIQUITI NETWORKS igazolja, hogy a AF-5XHD típusú rádióberendezés megfelel a 2014/53/EU irányelvnek. Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: www.ubnt.com/complianceÍslenska [Icelandic] Hér með lýsir UBIQUITI NETWORKS yfir því að AF-5XHD er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 2014/53/EU. Fullur texti ESB samræmisyfirlýsing er að finna á eftirfarandi netfangi: www.ubnt.com/complianceItaliano [Italian] Il fabbricante, UBIQUITI NETWORKS, dichiara che il tipo di apparecchiatura radio AF-5XHD èconforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.com/complianceLatvių kalba [Latvian] Ar šo UBIQUITI NETWORKS deklarē, ka radioiekārta AF-5XHD atbilst Direktīvai 2014/53/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: www.ubnt.com/complianceLietuvių kalba [Lithuanian] Aš, UBIQUITI NETWORKS, patvirtinu, kad radijo įrenginių tipas AF-5XHD atitinka Direktyvą 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu: www.ubnt.com/complianceMalti [Maltese] B’dan, UBIQUITI NETWORKS, niddikjara li dan it-tip ta’ tagħmir tar-radju AF-5XHD huwa konformi mad-Direttiva 2014/53/UE. Id-dikjarazzjoni tal-konformità tista’ tiġi kkonsultata minn www.ubnt.com/complianceNorsk [Norwegian] UBIQUITI NETWORKS erklærer herved at utstyret AF-5XHD er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 2014/53/EU. Den fulle teksten til EU-samsvarserklæringen er tilgjengelig på følgende internettadresse: www.ubnt.com/compliancePolski [Polish] UBIQUITI NETWORKS niniejszym oświadcza, że typ urządzenia radiowego AF-5XHD jest zgodny z dyrektywą 2014/53/UE. Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym: www.ubnt.com/compliancePortuguês [Portuguese] O(a) abaixo assinado(a) UBIQUITI NETWORKS declara que o presente tipo de equipamento de rádio AF-5XHD está em conformidade com a Diretiva 2014/53/UE. O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: www.ubnt.com/complianceRomână [Romanian] Prin prezenta, UBIQUITI NETWORKS declară că tipul de echipamente radio AF-5XHD este în conformitate cu Directiva 2014/53/UE. Textul integral al declarației UE de conformitate este disponibil la următoarea adresă internet: www.ubnt.com/complianceSlovenčina [Slovak] UBIQUITI NETWORKS týmto vyhlasuje, že rádiové zariadenie typu AF-5XHD je v súlade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: www.ubnt.com/complianceSlovenščina [Slovenian] UBIQUITI NETWORKS potrjuje, da je tip radijske opreme AF-5XHD skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.ubnt.com/complianceEspañol [Spanish] Por la presente, UBIQUITI NETWORKS declara que el tipo de equipo radioeléctrico AF-5XHD es conforme con la Directiva 2014/53/UE. El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: www.ubnt.com/complianceSvenska [Swedish] Härmed försäkrar UBIQUITI NETWORKS att denna typ av radioutrustning AF-5XHD överensstämmer med direktiv 2014/53/EU. Den fullständiga texten till EU-försäkran om överensstämmelse finns på följande webbadress: www.ubnt.com/complianceOnline ResourcesWebsite www.ubnt.comSupport help.ubnt.comCommunity community.ubnt.comDownloads downloads.ubnt.com

Navigation menu