UTC Fire and Security Americas 760A-EFOB Key Fob User Manual 4661716a

UTC Fire & Security Americas Corporation, Inc. Key Fob 4661716a

Exhibit G

Page 1ELM 4-Button Keychain TouchpadELM 4-Button Keychain TouchpadDocument Number: 466-1716 Rev. PRELIMINARYJune 1999INSTALLATIONINSTRUCTIONSProduct SummaryThe ELM (Encrypted Learn Mode™) 4-Button Key-chain Touchpad is an alkaline battery-powered, wire-less touchpad that allows users to arm and disarm their system, activate a police or auxiliary panic alarm, or activate a panel or SnapCard™ output. Encrypted signal transmissions (or rolling code) pro-vide higher security and virtually eliminate signal fraud.The touchpad is designed to fit on a keychain, in a pocket or purse.Installation GuidelinesUse the following guidelines when adding Keychain Touchpads to the system:■Keychain Touchpads are learned into the panel assensors.■Each learned Keychain Touchpad uses one of theavailable sensor numbers.■Keychain Touchpads are learned into unsuper-vised groups (since they don’t send supervisorysignals) that determine how the panel respondswhen the lock and unlock buttons are pressedtogether (police or auxiliary alarm).■Keychain Touchpads can be bypassed or deleted.to prevent lost or stolen ones from operating thesystem.Tools Needed■NoneLearning ELM Keychain Touch-pads into Panel MemoryThis section describes how to learn Keychain Touch-pads into Concord Express panels.To learn ELM Keychain Touchpads as sensors:1) Disarm the system to level 1.2) Using an alphanumeric touchpad, enter program mode by pressing 8 + installer/dealer CODE + 00. The display shows SYSTEM PRO-GRAMMING.3) Press ƒ and the display shows SECURITY.4) Press A or B until the display shows SENSORS, then press ƒ. The display shows LEARN SEN-SORS.5) Press ƒ and the display shows SENSOR GROUP 0. Select the appropriate unsupervised group number (01, 03, 06, 07, 32) and press ƒ. The display shows TRIP SENSOR n (n = next avail-able sensor number).6) To change the displayed sensor number, select the desired number (1 through 24) you want assigned to the Keychain Touchpad, then press ƒ. The display shows TRIP SENSOR n.7) Trip the Keychain Touchpad by as follows:a). Press and release the unlock button quickly two times before the LED blinks, then press and hold the unlock button until the LED blinks three times. Immediately release the button.b). Press and release the unlock button one time before the LED blinks, then press and hold the unlock button until the LED blinks two times. Immediately release the button.c). Press and hold the unlock button until the LED blinks one time, then immediately release the button.The display should advance to the next avail-able sensor number, after successful learning.60-833EXHIBIT GUser’s Manual
Page 2ELM 4-Button Keychain Touchpad8) Repeat 7 a, b, and c until all ELM Keychain Touchpads are learned.9) Exit programming mode.Testing Keychain Touchpad OperationTest Keychain Touchpad operation by pressing thebuttons as described below:1) Unlock Button - disarms system to level 1.2) Lock Button -■panel attempts arming from level 1 to level 2 or from level 2 to level 3.If protesting, the panel responds as if BYPASS was pressed.■panel arms directly to level 3, with no delay.If protesting, the panel responds as if BYPASS was pressed.3) Lock and Unlock Buttons Together - panelresponds with an alarm condition (police or aux-iliary), based on the sensor group the touchpad islearned into.4) Star Button - panel or SnapCard output activatesbased on output configuration setting.TroubleshootingTable 1 describes what to do if you experience trouble with Keychain Touchpad programming or operation.SpecificationsCompatibility: Concord ExpressPower Requirements: 12V 33 mAh Alkaline BatteryRange: At least 500’ open airDimensions: L = 2.30” x W = 1.45” x H = .48”NoticesThis device complies with part 15 of the FCC rules. Operation is subject to the followingtwo conditions:1) This device may not cause harmful interference.2) This device must accept any interference received, including interference that maycause undesired operation. FCC ID No. B4Z-760A-EFOB.Changes or modifications not expressly approved by Interactive Technologies, Inc. canvoid the users’ authority to operate the equipmentITI is a registered trademarks of Interactive Technologies, Inc. ELM, Concord and Snap-Card are trademarks of Interactive Technologies, Inc.Table 1. TroubleshootingProblem Action/SolutionTouchpad does not learn (alphanumeric touchpad display does not advance to next available sensor number).Make sure Keychain Touchpad LED does not blink during quick press and release.Panel does not respond to Keychain Touchpad sig-nals.1. Check panel memory to verify panel learned the touchpad. Repeat learn-ing procedure if neces-sary.2. Touchpad is out of sync with panel (caused by 64 or more touchpad button activations out of panel receiving range). Resync touch-pad and panel by enter-ing sensor test mode and pressing the lock and unlock buttons together.Table 1. Troubleshooting (Continued)Problem Action/Solution651/777-2690651/779-4890

Navigation menu