UNION COMMUNITY T2 Fingerprint Access Controller User Manual AC7000 UserGuide 1 0

UNION COMMUNITY Fingerprint Access Controller AC7000 UserGuide 1 0

UserManual.wiki >

UNION COMMUNITY >

User Manual

eNBioAccess-T2 User Guide 3 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com <Glossary >  Administrator (Admin) - The administrator can access the terminal menu mode. He/she has the authority to add/modify/delete terminal users and to change the operating environment by changing settings. - If there is no registered administrator in the terminal, anybody can access to the terminal menu and change settings. It is recommended that more than one administrator will be necessarily registered in the terminal. - The administrator has the authority to change critical environmental settings of the fingerprint reader. So, special attention is required to its registration and operation.  1:1 Authentication - The user fingerprint is verified after entering User ID or Card. - Only User ID or the user fingerprint registered to the card is compared. This is called One-to-One Authentication.  1: N Identification - The user is searched only by the fingerprint. - The same fingerprint as the input fingerprint is identified among the registered fingerprints without User ID or Card entered. This is called One-to-N Identification.  Authentication Level - As a level used for fingerprint authentication, it is displayed in Step 1 to 9. Authentication cannot be allowed before the degree of match between two fingerprints is higher than the set authorization level. - The higher authentication level may ensure the higher security. But it requires the relatively high concordance rate. When authenticating User ID, it high likely to deny authentication. - 1:1 Level: Authentication level applied when 1:1 authentication - 1: N Level: Authentication level applied when 1: n authentication  Authentication Method - It refers FP(Fingerprint)Authentication, RF(Card)Authentication and a various types of authentication methods made by each of a combination.  LFD (Live Finger Detection): Fake fingerprint prevention function - The LFD allows only actual fingerprints to be entered, except for any fake fingerprints made of rubber, paper, film, and silicon and the like.

eNBioAccess-T2 User Guide 4 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com Table of Contents 1. Before Getting Started ................................................................................. 6 1.1. Safety Notes ........................................................................................................ 6 1.2. Product Details ................................................................................................... 7 1.2.1. FRONT ...................................................................................................... 7 1.2.2. REAR ......................................................................................................... 8 1.2.3. Input / Output ............................................................................................. 9 1.3. Screen information during operation .............................................................. 12 1.3.1. Initial Screen ............................................................................................ 12 1.3.2. Icons ........................................................................................................ 12 1.3.3. Function KEY ........................................................................................... 13 1.3.4. Main Screen ............................................................................................. 13 1.4. LED information during operation ................................................................... 15 1.5. Voice information during operation ................................................................. 15 1.6. Buzzer guide announced during operation .................................................... 15 1.7. How to register and enter the correct fingerprint ........................................... 16 2. Product Descriptions ................................................................................. 17 2.1. Product Features .............................................................................................. 17 2.2. Diagram ............................................................................................................. 18 2.2.1. Single Type (Door Lock) ........................................................................... 18 2.2.2. Single Type (Lock Controller) ................................................................... 18 2.2.3. Dummy Type (MCP040) ........................................................................... 18 2.2.4. Network Type (Door Lock) ........................................................................ 19 2.2.5. Network Type (Lock Controller) ................................................................ 19 2.3. Product Specification ....................................................................................... 20 3. Environment Setting .................................................................................. 21 3.1. Checkpoints before Environment Setting ....................................................... 21 3.1.1. Menu ........................................................................................................ 21 3.1.2. Administration authentication ................................................................... 21 3.1.3. How to access the menu without administrator authentication ................. 22 3.1.4. Save Settings ........................................................................................... 22 3.1.5. Default Setting ......................................................................................... 23 3.1.6. Setting guide for Network Configuration ................................................... 24 3.2. How to register the terminal in Admin App ..................................................... 27 3.2.1. Install iAccess M Plus................................................................................ 27 3.2.2. Execute and Log in iAccess M Plus ........................................................... 27 3.2.3. Access to Terminal BLE REDAY ................................................................. 27 3.2.4. Terminal login Admin App ......................................................................... 28 3.2.5. Administrator authentication of the terminal ............................................ 28 3.2.6. Terminal registration ................................................................................. 28 3.3. Access Device with Admin App ....................................................................... 29 3.4. Access and Registration between ACM Pro and terminal ............................. 30 3.4.1. Install ACM Pro ......................................................................................... 30 3.4.2. Execute ACM Pro ...................................................................................... 30 3.4.3. Set in terminal .......................................................................................... 31 3.4.4. LAN connection in terminal ....................................................................... 31 3.4.5. Register the terminal in ACM Pro .............................................................. 32 3.5. Menu Configuration .......................................................................................... 33 3.6. USER ................................................................................................................. 39

eNBioAccess-T2 User Guide 5 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.6.1. Menu Configuration .................................................................................. 39 3.6.2. ADD.......................................................................................................... 39 3.6.3. AUTO ADD ................................................................................................ 41 3.6.4. MODIFY .................................................................................................... 42 3.6.5. DELETE .................................................................................................... 43 3.6.6. DELETE ALL .............................................................................................. 43 3.7. Network Menu ................................................................................................... 44 3.7.1. Menu Configuration .................................................................................. 44 3.7.2. AUTH Mode .............................................................................................. 45 3.7.3. Terminal ID .............................................................................................. 45 3.7.4. Terminal ................................................................................................... 46 3.7.5. Server....................................................................................................... 47 3.8. Option Menu...................................................................................................... 48 3.8.1. Menu configuration .................................................................................. 48 3.8.2. ATTEND .................................................................................................... 48 3.8.3. Screen ...................................................................................................... 50 3.8.4. SAVE ........................................................................................................ 52 3.8.5. TIMEOUT.................................................................................................. 53 3.8.6. LOCKING .................................................................................................. 54 3.9. INT DEVICE ....................................................................................................... 56 3.9.1. Menu Configuration .................................................................................. 56 3.9.2. FP SENSOR ............................................................................................... 56 3.9.3. BEEP ........................................................................................................ 58 3.9.4. VOICE ...................................................................................................... 58 3.9.5. BLE ........................................................................................................... 58 3.9.6. TAMPER .................................................................................................... 59 3.10. EXT DEVICE ...................................................................................................... 60 3.10.1. Menu Configuration .................................................................................. 60 3.10.2. DOORLOCK .............................................................................................. 60 3.10.3. RS485....................................................................................................... 63 3.10.4. WIEGAND ................................................................................................. 64 3.11. STATUS ............................................................................................................. 67 3.11.1. Menu Configuration .................................................................................. 67 3.11.2. DB INFO ................................................................................................... 67 3.11.3. NETWORK ................................................................................................ 67 3.11.4. OPTION .................................................................................................... 68 3.11.5. INT DEVICE .............................................................................................. 68 3.11.6. EXT DEVICE ............................................................................................. 68 3.11.7. I/O PORT .................................................................................................. 68 3.11.8. VERSION .................................................................................................. 69 3.12. RECOVERY ....................................................................................................... 70 3.12.1. Menu Configuration .................................................................................. 70 3.12.2. INITIALIZE ............................................................................................... 70 3.12.3. SELF TEST ................................................................................................ 71 3.12.4. BACKUP .................................................................................................... 75 3.12.5. REBOOT ................................................................................................... 77

eNBioAccess-T2 User Guide 6 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 1. Before Getting Started 1.1. Safety Notes  Warning Do not operate the terminal with wet hands, and pay attention not to let any liquid such as water enter inside the terminal. - > Otherwise, malfunction or electric shock may be caused. Keep the terminal away from inflammables. - > Otherwise, it may cause a fire. Do not disassemble, repair or remodel the terminal at your disposal. - > Otherwise, it may cause malfunction, electric shock, or a fire. Do not allow children to touch the terminal carelessly. - > Otherwise, it may cause safety accidents of children or malfunction. - Non-compliance of safety notes may cause death or serious injury for users.  Cautions Do not install the terminal in a place exposed to direct sunlight. → Otherwise, it may cause malfunction, deformation and discoloration. Do not install the terminal in humid or dusty places. → Otherwise, it may cause malfunction. Do not clean this terminal by sprinkling water, nor wipe it with benzene, thinner, and alcohol. → Otherwise, it may cause electric shock or a fire. Keep the terminal away from magnets. → Otherwise, it may cause failure and malfunction. Keep the fingerprint input section clean. → Otherwise, the fingerprint cannot be recognized correctly. Do not spray insecticides or inflammables on the terminal. → Otherwise, it may cause deformation and discoloration. Keep the terminal away from shock or sharp objects. → Otherwise, it may damage the terminal and result in malfunction. Do not install the terminal in a place where there is a severe change in temperature. → Otherwise, it may cause malfunction. - Non-compliance of safety notes may cause personal injury or property damage for users. ※ We are not responsible for any accidents and damage that may arise from non-compliance of the information in this manual.

eNBioAccess-T2 User Guide 7 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 1.2. Product Details 1.2.1. FRONT Camera LCD Function KEY (F1~F4) Speaker Card Sensor (EM/SC/HID) Fingerprint Sensor State LED BLE embedded USB assist device (UDL10) connection

eNBioAccess-T2 User Guide 8 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 1.2.2. REAR Fixed bracket Cable harness

eNBioAccess-T2 User Guide 9 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 1.2.3. Input / Output 1.2.3.1. Cable & Connector

eNBioAccess-T2 User Guide 10 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 1.2.3.2. Pin Details Pin number Line color Label (Line name) Explanation IN/OUT Note 1 ORANGE EXT Inside open IN Connect to Exit button 2 YELLOW DM0 DoorMonitor0 IN Sense door state(DM0) 3 GREEN DM1 DoorMonitor1 IN Sense door state(DM1) 4 BLUE DM2 DoorMonitor2 IN Sense door state(DM2) 5 BLACK GND GND - Ground connection(for door monitor) 6 RED 5V DC5V OUT DC 5V output 7 BLACK PGND Power GND - Power supply ground connection 8 GREEN R4A RS485A BI RS-485 interface 9 BLUE R4B RS485B BI RS-485 interface 10 ORANGE WO0 WIE_OUT0 OUT Output WIGAND (WO0) 11 YELLOW WO1 WIE_OUT1 OUT Output WIGAND (WO1) 12 BROWN WI0 WIE_IN0 IN Input WIGAND (WI0) 13 PURPLE WI1 WIE_IN1 IN Input WIGAND (WI1) 14 BLACK GND GND - Ground connection (WIGAND signal) 15 RED - N_TXN OUT LAN I/F (LAN cable) 16 BLACK - N_TXP OUT LAN I/F (LAN cable) 17 GREEN - N_RXN IN LAN I/F (LAN cable) 18 WHITE - N_RXP IN LAN I/F (LAN cable) 19 RED 12V DC12V IN DC 12V power supply input 20 BLACK GND Power GND - Power supply ground connection (Adapter) 21 RED 12V DC12V OUT DC 12V put out power 22 GRAY L1C LOCK1_COM OUT Lock1 COM terminal 23 BROWN L1NC LOCK1_NC OUT Lock1 NC terminal 24 WHITE L1NO LOCK1_NO OUT Lock1 NO terminal 25 PURPLE L2 LOCK2 OUT Lock2 terminal 26 BLACK GND GND - Ground connection (Lock connecter) 27 BLACK PGND Power GND - Power supply ground connection (Lock power) 28 BLACK PGND Panel GND - Panel ground connection (Earth) 1.2.3.3. Terminal <- > MCP040 wiring Category T2 terminal (Line name) MCP040 RS485A R4A (green) RDRA+ RS485B R4B (blue) RDRA- ground connection GND (black) G

eNBioAccess-T2 User Guide 11 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 1.2.3.4. Terminal <- > LC015B wiring Category T2 terminal (Line name) LC015B RS485A R4A (green) 485A RS485B R4B (blue) 485B ground connection GND (black) GND DOOR MONITOR IN1(If this pin is not used, connect to GND Pin.) INSIDE OPEN IN0 DC12V (LC015B separate power supply) DC12V IN ground connection (Power only for LC015B) GND But, door open time can be set with DIP SWITCH of LC015B (Maximum open time is 5 sec.) 1.2.3.5. Terminal <- > EM Type Door Lock wiring Category T2 terminal (Line name) EM Door Lock Lock L1NC (Green) + GND GND (Black) - Door Monitor DM0 (Black) NC(Normal Close) 1.2.3.6. Terminal <- > WIEGAND Device wiring Category T2 terminal (Line name) WIEGAND Device WIEGAND INPUT0 WI0(갈색) Wiegand output0 WIEGAND INPUT1 WI1(보라) Wiegand output1 WIEGAND OUTPUT0 WO0(주황) Wiegand input0 WIEGAND OUTPUT1 WO1(노랑) Wiegand input1 GND GND (검정) GND

eNBioAccess-T2 User Guide 12 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 1.3. Screen information during operation 1.3.1. Initial Screen When powering on at first, the screen is displayed as follow. 1.3.2. Icons Server connection State NONE : No use network : LAN line is disconnected. : LAN line is connected. (Only link is connected.) : Connected with server Gate State : Gate is closed. : Gate is opened. : Gate is opened forcedly(unusual door open state) : Gate communication problem Warning signal State NONE : Normal : Terminal Disassembly State Fire detection State NONE : Normal : Sensed by fire detector(Valid on DM2 fire set) BLE connection State NONE : Disconnected with Admin App : Connected with Admin App MCP040 connection State NONE : MCP040 is not used.(Normal state) : MCP040 Mode and bad communication state. : MCP040 Mode and normal communication state. UDL connection State NONE : UDL is not used (Normal state). : UDL is connected. State icon Operation Mode TNA Mode Date and Time

eNBioAccess-T2 User Guide 13 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 1.3.3. Function KEY Icon Meaning Function Key Explanation UP F1 Move cursor up. DOWN F3 Move cursor down. LEFT F2 Move cursor to left. ESC F2 long Move to upper menu. RIGHT F4 Move cursor to right. ENTER F4 long or F4 Move to submenu. ENABLE DISABLE F2 Category choice (ENABLE or DISABLE). 1.3.4. Main Screen Operating in Exclusive mode Initial Screen Operating in Network mode Initial Screen Operating in Dummy mode Initial Screen Operating in lock mode (Reject all users authentication)

eNBioAccess-T2 User Guide 14 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com Menu of Initial Screen Authentication succeess Authentication failure Waiting for Card Input Waiting for Fingerprint Input Waiting for Admin App registration Upgrading firmware for eNBioAccess-T2

eNBioAccess-T2 User Guide 15 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 1.4. LED information during operation LED Operating state Remark RED Normal OFF Alarm ON or Flash Authentication Failure ON (Maintain during authentication time)  OFF GREEN Normal OFF LOCK OPEN ON Authentication Success ON (Maintain during authentication time)  OFF BLUE Terminal Normal(alive) Flash at intervals of 5 seconds Function Key LED Enter menu Always ON Touch in initial screen. ON(Maintain for 10 seconds)  OFF 1.5. Voice information during operation Category Voice information Fingerprint Input Please enter your fingerprint. Authentication success You are authorized. Authentication failure Please try again. 1.6. Buzzer guide announced during operation Buzzer Sound State Explanation Ppik Key touch Card tag Fingerprint touch -Pressing key or reading card -When inputting fingerprint, input has been completed and hands can take off. Ppibik Failure If authentication fails or the user's input is wrong Ppiriririk Waiting for input It shows the state for waiting user’s input such as fingerprint or password. Ppiririk Succeess Authentication success or setting completion

eNBioAccess-T2 User Guide 16 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 1.7. How to register and enter the correct fingerprint  Correct fingerprint input method Enter your fingerprint as if you take a thumbprint by using your forefinger if possible. The fingerprint cannot be correctly registered and entered only by your fingertips. The center of the fingerprint should be touched with the fingerprint input section.  Enter the fingerprint of your forefinger if possible. When using your forefinger, you can enter your fingerprint correctly and safely.  Make sure that the fingerprint is unclear or wounded. Too dry, wet, blurry or wounded fingerprints are difficult to recognize. In this case, the fingerprint of another finger should be registered.  Precautions subject to your fingerprint state. The availability of the fingerprint may vary subject to your fingerprint state.  This product consists of a fingerprint recognition system and cannot recognize the damaged or unclear fingerprints. The fingerprint should be registered using the RF card.  If your hands are dry, you can blow your breath on the system to operate it more smoothly.  For children, too small or unclear fingerprints may be difficult or impossible to use. They need to register a new fingerprint every six months.  For seniors, the fingerprint with too many lines may not be registered.

eNBioAccess-T2 User Guide 17 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com  It is recommended that you will register more than two fingerprints if possible.  In order to increase the fingerprint authentication rate, it is recommended to use six of the ten fingers as illustrated below (both thumbs, forefingers, middle fingers). 2. Product Descriptions 2.1. Product Features  BLE is equipped. Door Control with smartphone is possible at close range.  It is equipped with Color Camera, and it saves the visitor’s video when authentication succeeds or fails.  Optional, Available to use as RF(125kHz), Smart Card(13.56MHz), HID Reader  Easy to verify your ID via fingerprint - The use of the fingerprint recognition technology (Biometrics) can prevent forgetting your password, losing your card or key, or avoid the risk of their theft. The use of personal fingerprints enhances the security of authentication.  Access control system using the local area network (LAN) - The fingerprint reader communicates with the authentication server using a TCP/IP protocol. Therefore, this terminal can be applied to the existing LAN and has easy expandability. It ensures a fast speed by 10/100 Mbps Auto Detect and facilitates management and monitoring via the network.  Provide various registration and authentication method Fingerprint Fingerprint registration Fingerprint authentication Card Card registration Card authentication Card or Fingerprint Card, Fingerprint registration Card or Fingerprint authentication Card and Fingerprint Card, Fingerprint registration Fingerprint authentication after Card authentication Mobile card Mobile Card registration (registration only via server and admin App) Mobile Card authentication

eNBioAccess-T2 User Guide 18 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 2.2. Diagram 2.2.1. Single Type (Door Lock) 2.2.2. Single Type (Lock Controller) 2.2.3. Dummy Type (MCP040) Door Lock Lock control BLE 2.4G Mobile App T2 Close Open Lock Controller (LC010, LC015) Mobile App RS485 BLE 2.4G T2 Close Open RS485 MCP040 Ethernet Server T2 Lock/Open Lock/Open Lock/Open RS485ID #2 RS485ID #1 RS485ID #3

eNBioAccess-T2 User Guide 19 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 2.2.4. Network Type (Door Lock) 2.2.5. Network Type (Lock Controller) Lock Control BLE 2.4G Mobile App Close Ethernet Open T2 Door Lock Ethernet Internet Server Internet RS485 Lock Controller (LC010, LC015) BLE 2.4G Mobile App Ethernet Ethernet T2 Close Open Server

eNBioAccess-T2 User Guide 20 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 2.3. Product Specification Category Spec CPU 32Bit RISC CPU(400MHz) MEMORY 64M DDR RAM, 32M NOR,128M NAND Camera VGA, F2.8, View angle 61 degree LCD 1.77’’ Color LCD Fingerprint Sensor Optical / 500 DPI Authentication Method Fingerprint, RF Card, Mobile Card Authentication Speed 1:N < within1sec. (based on 1,000 fingerprints) Fingerprint capacity 20,000 Fingerprints, 10,000 users (Two identical fingerprints registration per user) Note) Similar fingerprint inspection is possible when the number of fingerprints is less than 200. Log capacity 100,000 logs Communication interface TCP/IP, Wiegand In/Out (26/34bit),RS485 Lock Deadbolt, EM Lock, Door Strike, Automatic Door Temperature / Humidity -20~60 ℃ / < RH 90% Certification KC, CE, FCC Size 58mm(W) * 191mm(H) * 62mm(D)

eNBioAccess-T2 User Guide 21 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3. Environment Setting 3.1. Checkpoints before Environment Setting 3.1.1. Menu Press F4 long until the menu screen is displayed. It is available to enter the menu without authentication because the manager doesn’t register when shipping the product. 3.1.2. Administration authentication When the administrator is registered, the admin authentication screen is displayed at first as follows. ▶ Administrator authentication Administrator authentication is progressed with fingerprint and card. You can access each menu if the authentication succeeds. Admin authentication is displayed only if there is a registered user. Admin authentication displays only if admin is enrolled already. The admin authentication is needed only in accessing menu mode. It enables to access every menu until you completely escape from main menu.

eNBioAccess-T2 User Guide 22 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.1.3. How to access the menu without administrator authentication This is the method to enter the Menu in exceptional cases such as losing your administrator card that is registered in the terminal or inability to make a fingerprint authentication because of absence of administrator. ① Power terminal OFF. ② Disassemble device and make case open state. ③ While case opens, make DIP of rear side switch ON state as follows. ④ Power terminal ON. ⑤ After the terminal completely booted, Press F1 longer to enter the menu with buzzer sound “Ppiririk”. ★ Caution: You should return DIP SWITCH OFF after modification. 3.1.4. Save Settings ▶ If there are some changes, the following screen appears. ▶ If you select “YES”, then save them with buzzer sound “Ppibibig” and reboot. ▶ If there are no changes, it returns to the previous menu screen. ▶ While changing the settings in the menu, if there is no input for 30 seconds, it returns to the previous menu. OFF ON ON 1 2

eNBioAccess-T2 User Guide 24 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com BIT or 34 BIT > SITE CODE > SEND INFO 3.1.6. Setting guide for Network Configuration 3.1.6.1. Single Type (Door Lock=STRIKE) Menu position Possible setting MENU>NETWORK> NO USE MENU>EXT DEVICE>DOORLOCK>LOCK1>TYPE STRIKE/OK MENU>EXT DEVICE>DOORLOCK>DM0 N/O or N/C MENU>EXT DEVICE>DOORLOCK>LOCK2>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM1 NONE MENU>EXT DEVICE>DOORLOCK>DM2 NONE MENU>EXT DEVICE>RS485>TYPE NONE 3.1.6.2. Single Type (Door Lock=MOTOR) Menu position Possible setting MENU>NETWORK> NO USE MENU>EXT DEVICE>DOORLOCK>LOCK1>TYPE MOTOR1 MENU>EXT DEVICE>DOORLOCK>DM0 N/O or N/C MENU>EXT DEVICE>DOORLOCK>LOCK2>TYPE MOTOR2 MENU>EXT DEVICE>DOORLOCK>DM1 N/O or N/C MENU>EXT DEVICE>DOORLOCK>DM2 NONE MENU>EXT DEVICE>RS485>TYPE NONE 3.1.6.3. Single Type (Lock Controller=LC010) Menu position Possible setting MENU>NETWORK> NO USE MENU>EXT DEVICE>DOORLOCK>LOCK1>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM0 NONE MENU>EXT DEVICE>DOORLOCK>LOCK2>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM1 NONE MENU>EXT DEVICE>DOORLOCK>DM2 NONE MENU>EXT DEVICE>RS485>TYPE LC010 MENU>EXT DEVICE>RS485>DEV ID 0 3.1.6.4. Single Type (Lock Controller=LC015) Menu Position Possible setting MENU>NETWORK> NO USE MENU>EXT DEVICE>DOORLOCK>LOCK1>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM0 NONE MENU>EXT DEVICE>DOORLOCK>LOCK2>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM1 NONE MENU>EXT DEVICE>DOORLOCK>DM2 NONE

eNBioAccess-T2 User Guide 25 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com MENU>EXT DEVICE>RS485>TYPE LC015 MENU>EXT DEVICE>RS485>DEV ID 0 3.1.6.5. Dummy Type (RS485=MCP040) Menu Position Possible setting MENU>NETWORK> N/A (Use : When only downloading DB) MENU>EXT DEVICE>DOORLOCK>LOCK1>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM0 NONE MENU>EXT DEVICE>DOORLOCK>LOCK2>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM1 NONE MENU>EXT DEVICE>DOORLOCK>DM2 NONE MENU>EXT DEVICE>RS485>TYPE MCP040 MENU>EXT DEVICE>RS485>DEV ID Use in 1~7 3.1.6.6. Network Type (Door Lock=STRIKE) Menu Position Possible setting MENU>NETWORK> USE MENU>NETWORK>USE>AUTH MODE TN MENU>NETWORK>USE>TERMINAL ID 0001 MENU>NETWORK>USE>TERMINAL>STATIC IP:192.168.0.3 SN:255.255.255.0 GW:192.168.0.1 MENU>NETWORK>USE>SERVER IP:192.168.0.2 PORT:7332 MENU>EXT DEVICE>DOORLOCK>LOCK1>TYPE STRIKE/OK MENU>EXT DEVICE>DOORLOCK>DM0 N/O or N/C MENU>EXT DEVICE>DOORLOCK>LOCK2>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM1 NONE MENU>EXT DEVICE>DOORLOCK>DM2 NONE MENU>EXT DEVICE>RS485>TYPE NONE 3.1.6.7. Network Type (Door Lock=MOTOR) Menu Position Possible setting MENU>NETWORK> USE MENU>NETWORK>USE>AUTH MODE TN MENU>NETWORK>USE>TERMINAL ID 0001 MENU>NETWORK>USE>TERMINAL>STATIC IP:192.168.0.3 SN:255.255.255.0 GW:192.168.0.1 MENU>NETWORK>USE>SERVER IP:192.168.0.2 PORT:7332 MENU>EXT DEVICE>DOORLOCK>LOCK1>TYPE MOTOR1 MENU>EXT DEVICE>DOORLOCK>DM0 N/O or N/C MENU>EXT DEVICE>DOORLOCK>LOCK2>TYPE MOTOR2 MENU>EXT DEVICE>DOORLOCK>DM1 N/O or N/C

eNBioAccess-T2 User Guide 26 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com MENU>EXT DEVICE>DOORLOCK>DM2 NONE MENU>EXT DEVICE>RS485>TYPE NONE 3.1.6.8. Network Type (Lock Controller=LC010) Menu Position Possible setting MENU>NETWORK> Use MENU>NETWORK>USE>AUTH MODE TN MENU>NETWORK>USE>TERMINAL ID 0001 MENU>NETWORK>USE>TERMINAL>STATIC IP:192.168.0.3 SN:255.255.255.0 GW:192.168.0.1 MENU>NETWORK>USE>SERVER IP:192.168.0.2 PORT:7332 MENU>EXT DEVICE>DOORLOCK>LOCK1>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM0 NONE MENU>EXT DEVICE>DOORLOCK>LOCK2>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM1 NONE MENU>EXT DEVICE>DOORLOCK>DM2 NONE MENU>EXT DEVICE>RS485>TYPE LC010 MENU>EXT DEVICE>RS485>DEV ID 0 3.1.6.9. Network Type (Lock Controller=LC015) Menu Position Possible setting MENU>NETWORK> USE MENU>NETWORK>USE>AUTH MODE TN MENU>NETWORK>USE>TERMINAL ID 0001 MENU>NETWORK>USE>TERMINAL>STATIC IP:192.168.0.3 SN:255.255.255.0 GW:192.168.0.1 MENU>NETWORK>USE>SERVER IP:192.168.0.2 PORT:7332 MENU>EXT DEVICE>DOORLOCK>LOCK1>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM0 NONE MENU>EXT DEVICE>DOORLOCK>LOCK2>TYPE NONE MENU>EXT DEVICE>DOORLOCK>DM1 NONE MENU>EXT DEVICE>DOORLOCK>DM2 NONE MENU>EXT DEVICE>RS485>TYPE LC015 MENU>EXT DEVICE>RS485>DEV ID 0

eNBioAccess-T2 User Guide 27 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.2. How to register the terminal in Admin App 3.2.1. Install iAccess M Plus iAccess M Plus is the smartphone App for administrator controlling device via BLE. You can download and install it from Play Store. For more details, please refer iAccess M Plus installation guide. 3.2.2. Execute and Log in iAccess M Plus 3.2.3. Access to Terminal BLE REDAY If you press F3 long on initial screen, the terminal turns to BLE READY.

eNBioAccess-T2 User Guide 28 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.2.4. Terminal login Admin App When the terminal is BLE REDAY, press ADD on iAccess M Plus App and select the terminal. If you know the administrator's ID and password, then click OK to log in. If you do not know the administrator’s ID & password and click OK in empty state. 3.2.5. Administrator authentication of the terminal If an administrator is registered in the terminal, it requires to input card or fingerprint for administrator authentication. If the administrator is not registered in the terminal, it requires no further authentication and authentication succeeds immediately. 3.2.6. Terminal registration When admin authentication is successful, Device registration screen is displayed. Press Registration button and complete Device registration. Input admin’s card or fingerprint “Ppiririk” Success & output Buzzer sound

eNBioAccess-T2 User Guide 29 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.3. Access Device with Admin App If the terminal registration on Admin App is successful, the list is displayed as follows. When pressing View, the pop-up window is displayed to connect the terminal. If the administrator is registered in the terminal, it requires the administrator authentication. If there is no administrator, the login succeeds immediately. If the login is successful, you receive the list of users registered with the Admin App screen. BLE icon is displayed on the terminal. When you log out after finishing the setting from Admin App, BLE icon disappears from the initial screen of the terminal. If it is successful to access, it is available to add / delete user, inquire log data, modify the setting and etc. For more details, please refer the document for Administrator App user guide.

eNBioAccess-T2 User Guide 30 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.4. Access and Registration between ACM Pro and terminal 3.4.1. Install ACM Pro When shipping the product, it installs ACM Pro Program in PC from the provided CD. For installation guide, please refer the relevant document. 3.4.2. Execute ACM Pro If executing the program, login screen is displayed. Enter User ID that is previously registered and password and then press OK. If login is successful, the screen is displayed as follows.

eNBioAccess-T2 User Guide 31 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.4.3. Set in terminal In order to connect the terminal to the server, set to the network mode and set the information. Move to MENU > NETWORK > USE > TERMINAL and check whether lower information is correct or not. If you have not changed the device network information, it is displayed as follows. In order to access the server Move to MENU > NETWORK > USE > SERVER and check the lower information correctly sets or not. If you do not change the server network information, it is displayed as follows. 3.4.4. LAN connection in terminal At first, you can see the unregistered state because the terminal is not registered.

eNBioAccess-T2 User Guide 32 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.4.5. Register the terminal in ACM Pro Select the unregistered terminal and press Registration button to activate the screen below. Enter device name and explanation to press OK. If the registration is successful, the screen is displayed as follow. For more details about ACM pro operation, please refer ACM Pro guide document.

eNBioAccess-T2 User Guide 33 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.5. Menu Configuration The whole menu is composed of seven, and main characteristics are as follows. Menu Submenu1 Submenu2 Submenu3 USER ADD USER USER ADMIN INPUT ID *Authentication Type Card FP MCARD *Authentication Condition OR AND ※ MCARD is OR condition only. ※ MCARD is not admitted to set up, state check only. Password AUTO ADD FP UID > FP1 > FP2 > OK Card UID > Card > OK MODIFY INPUT ID *Authentication Type Card FP MCARD *Authentication Condition OR AND ※ MCARD is OR condition only. ※ MCARD is not admitted to set up, state check only. FP registration (When checking authentication mode) Card registration (When checking authentication mode) DELETE Delete ID DELETE ALL

eNBioAccess-T2 User Guide 35 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com SETTING YYYYMMDD-hhmmss INT DEVICE FP SENSOR 1:1 LEVEL (1~9) 1:N LEVEL (5~9) LFD LEVEL NONE LOW MIDDLE HIGH AUTH TIME BEEP 0~3 VOICE 0~5 BLE BLE READY TAMPER NO ALARM ALARM EXT DEVICE DOOR LOCK LOCK1 *TYPE Not Use Strike/OK Indication Motor1 Schedule alarm *OPEN TIME 3[1~20sec] LOCK2 * TYPE NONE Fail Indication Motor2 Schedule alarm * OPEN TIME 3[1~20sec] OPEN ALARM TIME 5[0~20sec] 0: No Alarm 1~20: Alarm DM0 NONE Lock Normal Open Lock Normal Close DM1 NONE Lock Normal Open Lock Normal Close DM2 Not use Normal Open Normal Close Fire Normal Open Fire Normal Close Panic Normal Open Panic Normal Close Urgent Norm Open Urgent Normal Close

eNBioAccess-T2 User Guide 37 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com DATE: YYMMDD LOG SAVE: YES IMG SAVE:NO SHOW TO: x PING TO: x NET TO: x: INT DEVICE CARD TYPE: RF/SC CARD FMT: STD FP1:1:x FP1: N:x LFD: xx AUTH TIME: BEEP VOL: VOICE VOL: BLE Name/MAC---- XXXXXXX (BLE Name) XXXXXXXXXXXXXXXXX TAMPER:ALARM EXT DEVICE LOCK1---------------------- TYPE: STRIKE/OK OUT: N/O OPEN: 3000ms LOCK2 ------------------- TYPE: NONE OUT: N/O OPEN: 3000ms DOOR WARN: 0sec FORCE OPEN:NO RS485: LC010 RS485 ID: xxx WIEGAND---------------- IN/OUT :34B/34B SITECODE: xxx SEND:USERID I/O PORT LOCK1: HIGH LOCK2: HIGH DM0: HIGH DM1: HIGH DM2: HIGH W0IN: HIGH W1IN: HIGH INSIDE: HIGH TAMPER SW:HIGH VERSION HW FW Card BLE

eNBioAccess-T2 User Guide 38 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com SN(Serial Number) RECOVERY INITIALIZE CONFIG LOG DB FACTORY SELF TEST INT DEVICE VOICE CARD FP SENSOR CAMERA LED EXT DEVICE DOORLOCK SENSOR IN BACKUP LOG EXPORT USER EXPORT USER IMPORT FW UPDATE REBOOT

eNBioAccess-T2 User Guide 39 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.6. USER 3.6.1. Menu Configuration USER menu has the feature as follows. Category Explanation ADD Use to add user and admin with various certification conditions. AUTO ADD Use to add Card or Fingerprint user automatically. MODIFY Use to add certification conditions, card or fingerprint of registered user. DELETE Use to delete a registered particular user. DELETE ALL Use to delete all registered users. 3.6.2. ADD 3.6.2.1. USER TYPE If you press ADD in the menu, the screen asking the user type is displayed as follow. USER TYPE Explanation USER Only available for authentication No Authorization to access menu When selecting user, the screen is displayed as follow.

eNBioAccess-T2 User Guide 40 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com ADMIN Available to add and delete user. Available to access menu and modify it. When selecting the administrator, the screen is displayed as follows. 3.6.2.2. AUTH TYPE There are FP(Fingerprint), Card, and MCARD (Mobile card) in the menu. But MCARD can only provide the check state, and do not provide checking or unchecking. For checking or unchecking with MCARD, it is only available via Server and Admin App. There are AND and OR in authentication conditions. In AND, all authentication conditions should be satisfactory and then authentication succeeds. In OR, one of authentication conditions should be satisfactory and authentication succeeds. FP:0 ➔ FP is abbreviation of Finger Print. 0 means the registered FP number. (1FP means 2 fingerprints) CD:0➔ CD is abbreviation of CARD. 0 means the registered CARD number. Maximum card number is 1. (U) ➔ Means your Registration Authority is general user(USER). (A) ➔ Means your Registration Authority is administrator (ADMIN). [FR Authentication] [Card Authentication] [FP or Card Authentication] [FP and Card Authentication]

eNBioAccess-T2 User Guide 41 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.6.2.3. INPUT FP Input the same fingerprint twice when you check the Fingerprint as authentication type. If you want to add only one fingerprint, select 1. NO. If you input the fingerprint second times and they are normal, INPUT OK is displayed. If you want to add more fingerprints, select 2. YES. One user can register 20 people for maximum. 3.6.2.4. INPUT CARD When you check Card as AUTH TYPE, you will follow steps as below. If you input CARD on Waiting state, registration completes and INPUT OK screen is displayed. EM CARD ex) Card No.(5byte): 08h 01h 16h 1Dh D6h Card Format Card No. Display Method Standard 02207638 (16001DD6) (3+5)digits Decimal [022(16h)+07638(1DD6h)] SC CARD ex) Card No.(4byte): 52h 9Dh 06h E3h Card Format Card No. Display Method Standard 529D06E3 8digits Hex 3.6.3. AUTO ADD AUTO ADD is used when you want to register general users (not admin user) consecutively with card or fingerprint. If you select FP, it adds users by increasing ID consecutively only with fingerprint. If you select CARD, it adds users by increasing ID consecutively only with card.

eNBioAccess-T2 User Guide 42 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.6.3.1. AUTO ADD – 1. FP This is the menu when registering the users continuously only by fingerprint. Input fingerprint in twice and then the registration succeeded. If you want to add more users, select 2. YES, and continue the registration. User ID increases automatically. 3.6.3.2. AUTO ADD This is the menu when registering the users continuously only by card. After inputting the card, INPUT OK is displayed on the screen. If you want to add the other user, select 2. YES, and register the user. User IDs increases automatically. 3.6.4. MODIFY It is used when modifying the authentication type of the registered user. In authentication type, authentication type (fingerprint, card) and authentication condition (AND, OR) can be changed. If the modification type is modified, authentication information about the authentication type can be input.

eNBioAccess-T2 User Guide 43 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.6.5. DELETE It is used when deleting the registered users. 3.6.6. DELETE ALL It is used when deleting all the registered users. It should be careful when trying to delete, because all the users (general user, administrator) are deleted.

eNBioAccess-T2 User Guide 44 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.7. Network Menu 3.7.1. Menu Configuration Network menu has the following features. Category Explanation Remarks NO USE Network not used Standalone USE AUTH MODE TERMINAL ID TERMINAL SERVER Network mode Operation Mode Explanation Standalone This is the operation mode independently without server and communication. The administrator can control all the functions of the terminal. Authentication log is saved in the terminal but is not sent to server. After converting Standalone mode into Network mode and accessing in server, the authentication log saved internally is sent to sever. If you want to see the authentication log data in Standalone mode, move RECOVERY > BACKUP > LOG EXPORT from main menu, download it in USB through UDL module and check it by ACM Pro program. Network Mode This is the operation mode by communicating with the server and it can control the functions of the terminal by the remote-control. Depending on the authentication mode, the order of authentication can be different. (Authentication order about whether trying to authenticate in the terminal or the server first) Authentication log is sent to the server if the network is connected regardless of authentication mode.

eNBioAccess-T2 User Guide 45 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.7.2. AUTH Mode Authentication mode means the authentication priority to determine whether authentication processing is done in the terminal or the server when user-authentication. It is a valid setting only when using the network. All authentication log is sent to server through the network. AUTH MODE Explanation Server/Terminal Server  Terminal After trying to do server authentication at first, terminal authentication is processed. Terminal/Server Terminal  Server After trying to do terminal authentication at first, server authentication is processed. Server Server only Authentication is processed only in server. Terminal Terminal only Authentication is processed only in terminal. Even if it is “Terminal Only”, authentication log is sent to server. ★ In Server Only” mode, if the network is disconnected, all the authentication is processed in fail. If the mode is not “Server Only” (Server/Terminal, Terminal/Server, Terminal) and the network is disconnected, authentication is processed in the base of DB in the terminal. 3.7.3. Terminal ID Terminal ID is a valid information only when using the network, and it can be set in the range of 1~200. If a user registered in the terminal exist, you can’t change the Terminal ID.

eNBioAccess-T2 User Guide 46 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.7.4. Terminal It is used when setting the network information in the terminal. Network setting in the terminal can be set in Static IP and DHCP. STATIC: Set the value as a user wants. DHCP: Allocated flexibly. (It can be operated normally when using the router supporting DHCP.) If STATIC is used, it is used when setting IP, Subnet mark and Gateway address of the terminal. The following is the default setting value. Category Default Setting Value Terminal IP 192.168.0.3 SUBNET MASK 255.255.255.0 GATEWAY 192.168.0.1 It can set the address value as follows. Function Key Function Explanation F1 Increase the setting value F3 Decrease the setting value F2 Move to left F4 Move to right F4 Long Save the setting value

eNBioAccess-T2 User Guide 47 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.7.5. Server When the terminal accesses in server through the network, set the information. Default setting value is as follows. Category Default Setting Value Server IP 192.168.0.2 Port number 7332

eNBioAccess-T2 User Guide 49 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.8.2.1. TYPE It is used when setting ATTEND mode. If setting ATTEND mode, ATTEND mode is displayed in the screen when pressing Function Key shortly (F1~F4) in the default screen. Mode Explanation NONE F00 is only displayed in default screen. F1~F2 F1~F2 Function Key is recognized and F01, F02 are displayed in default screen. F1~F4 F1~F4 Function Key is recognized and, F01, F02, F03, F04 are displayed in default screen. F1~F49 F1~F4 Function Key is recognized and F01, F02, F03, F04, F11~F49 are displayed. Function Key Meaning F00 ACCESS MODE F01 CLOCK-IN MODE F02 CLOCK-OUT MODE F03 CHECK-OUT MODE F04 CHECK-IN MODE F11~F49 EXPANDED MODE TNA mode (F00~F49) is converted into F00 after 10 seconds if you don’t use AUTO TNA. 3.8.2.2. AUTO TNA AUTO TNA is the menu to determine whether to remain continually the setting TNA mode or not. Category Explanation NO The TNA mode is automatically returned into F00 after 10 seconds. YES The TNA mode is continuously displayed.

eNBioAccess-T2 User Guide 52 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.8.3.4. USER ID LEN It is used to change the length of user’s ID. If changing the user’s ID, it should change in the absence of a DB because it affects user’s DB that is internally registered. The setting range can be set from 4 to 16. If a user registered in the terminal exist, you can’t change the length of User ID. 3.8.3.5. DATE It is used to select the order of Year, Month and Day displayed in the default screen. YY: Year MM: Month DD: Day Through SETTING, you can set current Year, Month, Day and Time. 3.8.4. SAVE It is the menu including the function related to SAVE.

eNBioAccess-T2 User Guide 53 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.8.4.1. LOG SAVE It is used to set whether to save the authentication log in memory or not. The default setting is YES. 3.8.4.2. IMAGE SAVE It is used to set whether to save the captured photo from camera when authentication successes or fails. The default setting is Fail. 3.8.5. TIMEOUT It is the menu that has the setting related with timeout. 3.8.5.1. RESULT It is used to set the authentication result display how long it keeps for a seconds.

eNBioAccess-T2 User Guide 54 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com The setting range can be set from 0 to 5 seconds. If it set to 0, then don’t display the authentication result. 3.8.5.2. NET ERROR If it does not communicate with the server over a period of time, it is used to set whether there is a network communication error. If PING doesn’t come for a setting time in the server, it retries to connect the terminal. The setting range is available for 60~600 seconds. 3.8.5.3. PING It sets the cycle that terminal sets PING command to the server. The setting range is available for 30~255 seconds. 3.8.6. LOCKING Locking mode is the function that it rejects the authentication of all users until the administrator enters the menu and releases the locking mode. The default setting is NO USE.

eNBioAccess-T2 User Guide 55 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com The default screen is displayed as follows when setting to use locking mode.

eNBioAccess-T2 User Guide 56 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.9. INT DEVICE 3.9.1. Menu Configuration INT DEVICE menu has the features as follows. Category Explanation FP SENSOR 1:1 LEVEL 1: N LEVEL LFD LEVEL AUTH TIME BEEP Set Beep Sound. VOICE Set Voice Sound BLE BLE registration mode TAMPER Set the alarm when opening terminal case. 3.9.2. FP SENSOR For the fingerprint recognition, it sets for the user registration and authentication about the module installed inside. 3.9.2.1. 1:1 LEVEL It is the authentication level used when it tries 1:1 fingerprint authentication.

eNBioAccess-T2 User Guide 57 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.9.2.2. 1: N LEVEL It is the authentication level used when it tries 1: N fingerprint authentication. 3.9.2.3. LFD LEVEL It sets LFD LEVEL to prevent the duress fingerprint. If setting LFD LEVEL higher and higher, the ability to prevent the input of duress fingerprint produced by rubber, paper, film, and silicon etc. reinforces but too dry fingerprint cannot be input well. Also the authentication speed can be slow. 3.9.2.4. AUTH TIME It means the maximum time to process 1: N authentication. If the authentication time exceeds, authentication timeout occurs. The authentication time is 2 to 10 seconds, the default is 5 seconds.

eNBioAccess-T2 User Guide 58 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.9.3. BEEP It informs key touch, authentication success, and failure as beep and sets the beep level. The beep level is available from 0 to 3. 3.9.4. VOICE It supports the notice such as authentication success/failure and authentication retrial. It sets the authentication level. The voice level is available from 0 to 5. 3.9.5. BLE When registering the terminal in Administrator’s App, this menu is required. By using this menu, it can make the terminal BLE READY. Only if the terminal is BLE READY, it can perform the registration procedure of the terminal after the administrator app accesses the terminal. When pressing F3 long in the default screen of the terminal, it performs same operation with this menu. Regarding the method to register the terminal in the administrator APP, please refer 3.2 How to register the terminal in the administrator App.

eNBioAccess-T2 User Guide 59 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.9.6. TAMPER When disassembling the terminal randomly, it sets whether to sound the alarm. If selecting 1. NO ALARM, even if disassembling the terminal, the alarm doesn’t sound but icon is displayed. If selecting 2. ALARM, icon displays and the beep sounds in at regular intervals.

eNBioAccess-T2 User Guide 60 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.10. EXT DEVICE 3.10.1. Menu Configuration EXT DEVICE has the features as follows. Category Explanation DOORLOCK It sets the control device to lock through the internal relay. RS485 It sets the devices using RS485. WIEGAND It sets the device using WIEGAND. 3.10.2. DOORLOCK It is the menu to set lock device (Strike, Motor type door lock) by using LOCK1 and LOCK2 port. 3.10.2.1. LOCK1 type Category Explanation NONE No Use Strike/OK When connecting the light to mark authentication success/failure or 2. STRIKE/OK. MOTOR1 When connecting Motor lock

eNBioAccess-T2 User Guide 61 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.10.2.2. LOCK1 OPEN TIME It sets the time to give the signal when LOCK 1 sets 2. STRIKE/OK. Strike type means the time from opening to locking the door after authenticating. The default value is 3 seconds and the input range is 1 to 20 seconds. 3.10.2.3. LOCK2 type NONE When not using FAIL IND When connecting the light to mark authentication failure in Lock 2 MOTOR2 When connecting motor lock 3.10.2.4. LOCK2 OPEN TIME If Lock 2 sets FAIL IND, it sets the time to give the signal. The default value is 3 seconds and the input range is 1 to 20 seconds. 3.10.2.5. OPEN ALARM When the door open time expires and the door open alarm time is exceeded, the alarm sounds. The default value is 5seconds and the input range is 0 ~ 20 seconds. If it is set to 0, it will not beep. If it is set to 1 ~ 20 seconds, it will beep. Door open time Open alarm time DOOR OPEN state alarm

eNBioAccess-T2 User Guide 62 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.10.2.6. DM0 DM0(Door Monitor 0) is the input port and it is used to detect the signal state of door open. 3.10.2.7. DM1 DM1(Door Monitor 1) is the input port and it is used to detect the signal state of lock. 3.10.2.8. DM2 DM2(Door Monitor 2) is the input port and it is used to detect a various of sensor and alarm. For example, if connecting with fire sensor, it should set 4. FIRE N/O or 5. FIRE N/C and it may cause fire alarm and icon in case of fire. In case of fire, the door automatically opens for safety.

eNBioAccess-T2 User Guide 63 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.10.3. RS485 It is the setting for the device with RS485 communication to interface with external. 3.10.3.1. TYPE TYPE Explanation NONE It doesn’t use RS485. LC010 Lock Controller It controls LOCK through the other external module. LC015 Lock Controller It controls LOCK through the other external module. SR100 FP Dummy Reader When it installs the other FP dummy reader device in external and then operates, it is used. MCP040 Terminal operates as the dummy reader. If Terminal is connected with MCP040 device, icon is displayed in the default screen. If Terminal is not connected with MCP040, icon is displayed. The authentication result is determines whether or not successful by MCP040. RS485ID uses 1~7.

eNBioAccess-T2 User Guide 64 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.10.3.2. DEV ID DEV ID is the ID that distinguishes devices and it can be set up 0-7 during RS484 communication. 3.10.4. WIEGAND WIEGAND supports each one of Input port and Output port. 3.10.4.1. WIE-INPUT It is used to set the input type when working with the device connected into WIEGAND input port. Category Explanation NONE WIEGAND input port is not used. WIE26BIT EM, HID26 Card Module WIE34BIT Mifare Card Modules CUSTOM Use Access Manager program and set Wiegand format.

eNBioAccess-T2 User Guide 65 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.10.4.2. WIE-OUTPUT Category Explanation NONE WIEGAND output port is not used. WIE26BIT EM, HID26 Card Module WIE34BIT Mifare Card Modules CUSTOM Use Access Manager program and set Wiegand format. 3.10.4.3. CUSTOM BIT LENGTH It can set BIT length as 1~128. 3.10.4.4. SITE CODE It is used to set the value of Site Code that is sent to WIEGAND output port. 3.10.4.5. SEND INFO It is used to select the transmitting data by the output port.

eNBioAccess-T2 User Guide 66 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com SEND INFO Type None USER ID 26 Bit E.Parity(1)+ Site Code(8bit) + ID(16bit) + O.Parity(1) 34 Bit E.Parity(1)+ Site Code(8bit) + ID(24bit) + O.Parity(1) If the length of the User ID greater than 8, and sent in the following format without site code: E.Parity(1)+ ID(32bit) + O.Parity(1) Card 26 Bit E.Parity(1) + 24bit Card Number+ O.Parity(1) 34 Bit E.Parity(1) + 32bit Card Number + O.Parity(1)

eNBioAccess-T2 User Guide 67 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.11. STATUS 3.11.1. Menu Configuration STATE menu has the following features. STATE information Explanation DB INFO User DB, Authentication log data NETWORK The setting information related to network OPTION TNA, Screen setting, Saving, Time out, Lock mode INT DEVICE Display the setting state related to the internal device. EXT DEVICE Display the setting state related to the external device. I/O PORT Display the current signal of Input / Output port that interfaces with outside. VERSION Display the version of the equipped device in the terminal. 3.11.2. DB INFO It displays User’s DB information and the authentication log information. 3.11.3. NETWORK It displays the network setting value.

eNBioAccess-T2 User Guide 68 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.11.4. OPTION It displays the option setting value. 3.11.5. INT DEVICE It displays the setting value related to the internal device. 3.11.6. EXT DEVICE It displays the setting information related to the external device. 3.11.7. I/O PORT It reflects the current I/O Port state and displays it on the screen. Output Port: LOCK1, LOCK2 Input Port: DM0~DM2, W0IN, W1IN, INSIDE Open, Tamper When the input port shorts GND, the signal modifies from HIGH to LOW.

eNBioAccess-T2 User Guide 69 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.11.8. VERSION It displays the equipped module in the terminal and other version information.

eNBioAccess-T2 User Guide 70 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.12. RECOVERY 3.12.1. Menu Configuration RECOVERY has the features as follows. Category Explanation INITIALIZE CONFIG LOG DB FACTORY SELF TEST INT DEVICE EXT DEVICE BACKUP LOG EXPORT USER EXPORT USER IMPORT FW UPDATE REBOOT REBOOT 3.12.2. INITIALIZE It is used to initialize CONFIG, LOG DB, and FACTORY in the terminal. 3.12.2.1. CONFIG It is used to initialize the modified setting value in the menu as the default value when shipping from factory. If a user registered in the terminal exist, you can’t initialize the configuration information.

eNBioAccess-T2 User Guide 71 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.12.2.2. LOG DB INIT It is used to delete the user authentication log saved in the terminal. 3.12.2.3. FACTORY INIT If trying FACTORY INIT, setting data, authentication log data, and user registration information are initialized as setting state when shipping from factory. ★ It should be careful because the current data can be lost when you setting wrong. 3.12.3. SELF TEST It is used when the terminal tests the operation state about internal & external device by itself.

eNBioAccess-T2 User Guide 72 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.12.3.1. INT DEVICE It could test VOICE, CARD, FP SENSOR, CAMERA and LED equipped internally by itself. Category Explanation VOICE Voice output test CARD Card recognition test FP SENSOR Fingerprint recognition test CAMERA Camera equipment test LED LED output test Voice Test When authentication successes, it repeats and play voice guidance. Card Test As you see below, the screen displays “INPUT CARD” state at first. When recognizing the card, “Success” screen displays and it returns “INPUT CARD” state again. If you want to stop testing, press F2. FP Sensor Test FP Sensor Test is used to test the operation state of FP sensor from terminal. Input your fingerprint twice, if they are same, it shows “Success” screen. Otherwise, if not, it shows “Failure” screen.

eNBioAccess-T2 User Guide 73 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com Camera Test It is used to check whether the camera state is normal in the terminal to capture photos. LED Test It is used to check whether the state is normal about RED, GREEN and BLUE LED used to inform the operation state. At intervals of 2 seconds, RED, GREEN and BLUE LED changes from ON to OFF. 3.12.3.2. EXT DEVICE It can test the features related to the external device by itself. Category Explanation DOORLOCK Lock1, Lock2 SENSOR IN DM0 DM1 DM2 INSIDE OPEN TAMPER

eNBioAccess-T2 User Guide 74 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com DOORLOCK Test It is used to check the state of LOCK1, LOCK2 OPEN /CLOSE from the terminal. The procedure is as follows. SENSOR IN It is used to check the signal state about the input port. When the port shorts GND, if signal changes LOW, it is normal.

eNBioAccess-T2 User Guide 75 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.12.4. BACKUP When the saved data from the terminal sends to USB by using UDL device or brings the data from USB memory and then applies it, it is used. It is available only when the UDL module is. UDL is the option module, so it is not basically provided. If you want to get more information about UDL module, please contact NITGEN customer service. USB memory recommends using Sandisk.(NOTICE: UDL Device is not supported for all USB memory. UDL module may not work depending on the USB memory size, manufacturer, and method.) If Terminal detect UDL Device and USB memory, icon is displayed in the default screen. If icon isn’t displayed, all backup function doesn’t operate. 3.12.4.1. LOG EXPORT The saved log data from terminal saves in USB memory through UDL (User Data Downloader module). Only the log data in the selected period sends to USB and saves it through UDL. The file name saved in USB memory is divided by period as follows. 1. 1Day: L1Day.NLG, 2. 1~30Day: L30Day.NLG 3. 1~90Day: L90Day.NLG 4. 1~180Day: L180Day.NLG 5. ALL: ALL.NLG UDL module USB memory

eNBioAccess-T2 User Guide 76 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com or 3.12.4.2. USER EXPORT The saved User DB from the terminal saves in USB memory through UDL. It saves as USER.NDB file. or 3.12.4.3. USER INPUT It reads the user DB from USB memory through UDL and add it in terminal user DB. If inputting user DB in the terminal, all existing user DB are deleted. If you need the existing user DB saved in the terminal, back up first and try to input the user. It opens USER.NDB file in USB memory and brings into the terminal through UDL. The user registration data that you brought is reflected in the internal DB and added. ※ CAUTION: If you press F2 Key to stop in READ state, users loading will fail. or 3.12.4.4. FW update It is used when reading the firmware from USB memory through UDL and updating the terminal firmware. Firmware proceeds only when there is FW.NFW file name in USB memory. . or

eNBioAccess-T2 User Guide 77 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com 3.12.5. REBOOT It is used when rebooting the terminal.

eNBioAccess-T2 User Guide 78 12F, Daemyung Valeon bldg., 127, Beobwon-ro, Songpa-gu, Seoul, Korea (05836) Tel : 02-6488-3232 , Fax : 02-6488-3099, E-Mail :customer@nitgen.com http://www.nitgen.com FCC Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. “CAUTION : Exposure to Radio Frequency Radiation. This equipment should be installed and operated with a minumum distance of 20 cm between the radiator and your body.

Navigation menu