Trimble 99133 Smart Receiver Accessory User Manual

Trimble Navigation Limited Smart Receiver Accessory Users Manual

Users Manual

CAUTION: Please read the full user guide including all safety warnings, before operating this product.Trimble® PG200 GNSS Receiver©2014. Trimble Navigation Limited. All rights reserved. This product is protected by US and international copyright, trademark, and patent law as described in "Legal Notices" in the Trimble PG200 GNSS Receiver User Guide. PN 102388-00-ENG, Revision A (10/2014) Trimble Navigation Limited10368 Westmoor DriveWestminster, CO 80021USAwww.trimble.com102388-00-ENGTrimble Support SUPPORT TRIMBLE http://www.trimble.com/locator/locator.aspx TRIMBLE PG200 GNSS RECEIVER QUICK START GUIDE4 1PDF*102388-00-ENG*Made for• iPhone 6 Plus, iPhone 6• iPhone 5s, iPhone 5c, iPhone 5• iPad Air• iPad mini with Retina display• iPad (4th generation)• iPad miniDownload Trimble GNSS Status utility• Windows, Windows Embedded Handheld: www.trimble.com• Android: Google Play store• iOS: iTunes “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPhone or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPhone or iPad may affect wireless performance.PG200_ENG_QSG_MCS_1014.indd 2 10/28/2014 2:26:51 PM
LED information and power off1. Charge battery 2 35 hGNSS--- Pairing mode N/A--- --- ------ --- ------ --- --------- ------ ------ Solid CorrectedBluetooth / GNSS LED 3. Bluetooth connection Power LED Turn offHold Power button for 5 secondsuntil LED = - - -• Windows® 7, 8.x• Trimble Juno® 3 handheld (Windows Embedded Handheld 6.5)• Android* 4.1.x and later?2. Turn on1.2. When LEDs = , release Power button.After a few seconds, LED = --- --- ---1.2.Hold Power button LED = LED = 1.2. When LED = Offand LED = , release the Power button.Both LEDs = OffUse the Trimble® GNSS Status utility for: Use Settings > Bluetooth® for:• iOSPDF Solid <100% Solid 100%Off >50%--- --- --- <50%--- --- --- <15%- - - Charging and operationHold Power button LED = LED = *On Android devices, enable Mock Locations. See the Trimble PG200 GNSS Receiver User Guide for more information.PG200_ENG_QSG_MCS_1014.indd 3-4 10/28/2014 2:27:02 PM
FCC StatementThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesiredoperation.The device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Users are not permitted to make changes or modify the device in any way. Changes or modifications not expressly approved by Samsung will void the user’s authority to operate the equipment.FCC RF Radiation Exposure Statement: This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment. This device and itsantenna must not be co-located or operating in conjunction with any other antenna or transmitter.
Part 15.105 (B)Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules.
Industry Canada StatmentThis device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions: (1) This device may not cause interference and (2)this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts delicence.L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire debrouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si lebrouillage est susceptible d'en compromettre le fonctionnement.Industry Canada RF Radiation Exposure StatementThis equipment complies with Industry Canada RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.RF de l'Industrie Canada d'exposition aux radiations: Cet équipement est conforme à l'exposition del'Industrie Canada rayonnements RF limites établies pour unenvironnement non contrôlé. L’antenne pour ce transmetteur ne doit pas être meme endroit avecd’autres émetteurs sauf conformément à l'Industrie Canada procedures de produits Multi-émetteur.

Navigation menu