Transtek Medical Electronics AW2540-LS Bluetooth Module User Manual gbf 1251 b

Guangdong Transtek Medical Electronics Co.,Ltd Bluetooth Module gbf 1251 b

UserManual.wiki >

Transtek Medical Electronics >

AW2540-LS User Manual >

gbf-1319-b user Manual

Contents

1. AW2540 User Manual
2. gbf-1319-b user Manual

gbf-1319-b user Manual

User ManualBody Fat Analyzer GBF-1319-Bversion:1.0Please do read the user manual carefully and thoroughly so as to ensure the safe usage of this product, and keep the manual well for further reference in case you have problems.Thank you very much for selecting the Transtek Body Fat Analyzer GBF-1319-B. GUANGDONG TRANSTEK MEDICAL ELECTRONICS CO., LTDZone A, 5/F., Investment Building, No. 12, Huizhan East Rd., Torch Development District, Zhongshan, Guangdong, 528437, ChinaTEL:86-760-88282982 www.transtek.cnContains FCC ID:OU9AW2540-LS

2 3The warning signs and symbols are essential to ensure your correct and safe use of this product and protect you and others from injury. Please kindly find the meanings of the warning signs and symbols, which you may encounter in the label and user manual, as follows:To ensure your safety as well as the service life of your scale, please avoid using the scale under the following circumstances:Concurrent use of this device and implantable medical electronic instruments, e.g. Cardiac PacemakerConcurrent use of this device and wearable medical electronic instruments, e.g. electrocardiographConcurrent use of this device and other medical electronic instruments for life support, e.g. mechanical heartSlippery floor such as tile floorJumping onto the platform immediately after bath or with wet handsNear a cell phone or microwave ovenAvoid storage in the following locations:Where there is waterWhere the device may be exposed to extreme temperatures, humidity, moisture, direct sunlight, dust, or salt airWhere there is risk of shock or dropWhere you store chemicals or full of corrosive gasesWhere in reach of the infants or children Safety and Usage InformationYour Scale and Its EnvironmentSafety InformationSafety InformationINDICATIONS FOR USEThe Transtek Body Fat Analyzer measures weight and uses bio-electrical impedance analysis (BIA) technology to estimate body fat, total body water percentage, bone mass, and muscle mass in generally healthy adults 18 years of age or older. It is intended for use in the home / domestic setting only. CONTRAINDICATIONS1. This device is contraindicated for any female subject who may be suspected of, or is pregnant. Besides provided inaccurate readings, the affects of this device on the fetus are unknown. 2. This device is contraindicated for any person who is connected to a wearable or implantable electronic device or instrument such as a pacemaker or defibrillator.CAUTIONSymbol for “THE OPERATION GUIDE MUST BE READ” Symbol for “MANUFACTURER”Symbol for “ENVIRONMENT PROTECTION – Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice”Symbol for “TYPE BF APPLIED PARTS” The Bluetooth Combination MarkSymbol for “SERIAL NUMBER”Symbol for “DIRECT CURRENT”Symbol for “INDOOR USE ONLY”Symbol for “COMPLIES WITH FCC RULES”Transtek’s Body Fat Analyzer GBF-1319-B offers you a seamless way to manage your health. Please be aware that this device is designed for adults’ self-measuring and self-monitoring body fat level. Any information provided by this device is in no way meant to treat, cure or prevent any disease or illness from happening. This device should not be used by anyone who is acutely or chronically ill, suffering from a disease or taking medications that affect your water levels. The accuracy of readings for these patients has not been verified. Specific medical advice should be obtained from a physician.GBF-1319-B is equipped with data transmission function. It may emit electromagnetic energy so as to perform its intended function. Nearby portable and mobile RF communications equipment can affect the performance of GBF-1319-B.Portable and mobile RF communications equipment can affect the measuring accuracy of GBF-1319-B.Kindly note that the use of accessories, transducers or cables other than those specified, with the exception of transducers and cables sold by the manufacturer as replacement parts for internal components, may result in increased EMISSIONS or decreased IMMUNITY of GBF-1319-B.Be aware that misuse of electrical equipments can cause electric shock, burns, fire and other hazards. Warning that the GBF-1319-B should not be used adjacent to or stacked with other equipment.Manufacturer will make available on request circuit diagrams, component parts list,etc.WARNING:No modifications of this equipment is allowed.During using the Analyzer, the patient will contact with the surface and the electrode of the Analyzer.The device doesn’t need to be calibrated in two years lifetime.

4 5Efficient Use of Your ScaleList1. Body Fat Analyzer GBF-1319-B2. 3xAAA Batteries (1.5V each)3. User ManualUp ButtonSet ButtonDown Button LCD DisplayElectrodeBattery CompartmentUNIT ButtonElectrodeTo ensure the accuracy of measurement, please follow below instructions when you start measurement.Place the scale on a flat, hard surface. Soft surface such as carpet will affect the performance of the scale.Step onto the platform with bare feet. Stand still and keep full contact with the electrodes until the measurement is complete.Start measurement at least two hours after Getting up or Dinning.Avoid measurement immediately after strenuous exercise, sauna or bath, drinking, and dinning.Always start measurement in the same time slot and on the same scale located on the same flat, hard surface.OverviewDevice ComponentsSafety Information

76Transtek Body Fat Analyzer GBF-1319-B applies BIA (Bio-impedance Analysis) technology. A small amount of weak current flows through the human body so as to detect the bio-impedance and estimate body fat, body water, muscle mass and CAL-MAX. The electrical current is small and may not be felt. This BIA technology is cheap, safe, non-invasive, toxic-free and harmless. It also possesses the characteristics of simple operation and abundant information. The current mentioned above is less than 1mA. However, please be aware that anyone with an wearable or implantable medical electronic instrument, such as a pacemaker, must avoid using this device.The intended use of this device is for adult’s indoor use only. Body Fat Analysis ResultTotal Body Water Analysis ResultMuscle Mass Analysis ResultCalorie Analysis ResultStonePoundKilogramPercentageFootCentimeter AgeMaleMale AthleteFemaleFemale AthleteUser ID (Range from P1 to P8)LCD Display General InstructionsInitial Start-UpInsert the BatteriesOpen the battery door in the back of the scale.Insert the batteries (3 x AAA) into the battery compartment according to the polarity indications marked inside the compartment.* The digits “8888” will be shown on the LCD.Close the battery door and wait until the digits “0.0” are shown on the LCD.CAUTIONWhen the symbol “Lo ” appears, the device will power off in four seconds. Then you shall replace with a new set of batteries. Please replace all three batteries at the same time. Do NOT mix the old batteries with the new one. Worn batteries are hazardous waste. Do NOT dispose of them together with the household garbage. Please refer to the local ordinances and recycling instructions regarding disposal of the worn batteries.Less than target weightMore than target weightBluetooth iconData hasn’t been sent outTarget WeightDifference compare with target weightOverview

98With batteries correctly installed, press “UNIT” button in the back of the scale to select measurement unit. The default measurement unit is “pound”. You may press “UNIT” button to choose among pound, kilogram, stone.Initial Start-UpSelect Measurement UnitInitial Start-UpNote: If there is no operation in the weighing mode, the scale will turn off after a few seconds.If SUCCEED, symbol will be shown on the LCD.If FAIL, symbol “E1” will be shown on the LCD.Pair-UpWith the advanced Bluetooth 4.0 technology applied, the mobile or portable equipments, which are equipped with Bluetooth function in line with BLE Technical Specifications established by global organization Bluetooth SIG, are capable to receive your personal health data.Turn on Bluetooth and the App. Make sure both are ON when pair-up is proceeding.Press and hold “UNIT” button in the back of the scale to start pair-up. Symbol and symbol will be shown on the LCD alternatively, indicating pair-up is proceeding.Bluetooth Module No. :AW2540MV1Frequency RangeOutput Power RangeSupply Voltage2402MHz - 2480MHz-1 dBm2-3.6 VTransmitting Distance 10 meters

13126.Setting Athletic LevelAfter confirming Age, the system will divert to Athletic Level setting.As pictured below, the digit “1” blinks. The operator may press the function key or to increase or decrease the numeral. (Range: AC 1 to AC 5 )You may press and hold the function key or for fast changing the numeral. Press “SET” button to confirm Athletic Level.Weight Only OperationYour TRANSTEK Body Fat Analyzer will operate as a conventionalweight - reading scale. No special programming steps are required.Once the scale is initialized, as previously described, you may simply step onthe scale to measure your current weight. For only weight reading.1. Position the scale on a flat, hard surface. Carpeted or uneven floors may affect accuracy.2. Step onto the scale platform and remain still while the scale computes your weight.3. The scale will display your weight value.4. The scale will automatically turn off after a few seconds.Note: The weight value won’t be saved in the scale, and won’t be transmitted to the APP.1. Press the platform centre and remove your foot.2. “0.0” will be displayed.3. The scale will switch off and is now ready for use.This initialisation process must be repeated if the scale is moved.At all other times step straight on the scale.Initialising Your Scale5.Setting AgeAfter confirming Stature, the system will divert to Age setting.As pictured below, the digits “30” blinks. The operator may press the function key or to increase or decrease the numeral. (Age Setting Range for Normal Mode: 10 to 85 years old, Age Setting Range for Athlete Mode: 15-85years old)You may press and hold the function key or for fast changing the numeral. Press “SET” button to confirm Age.7. The display will show your settings once, then display “0.0”, you can start measuring. 8. Repeat procedure for a second user, or to change user details.Note: To update or overwrite the memorised data, follow the same procedure, making changes as required.Initial Start-UpInitial Start-Up

With original SENSE ON patent technology, GBF-1319-B will automatically switch on as you step on the platform barefooted. Stand still and keep full contact with the electrodes until the LCD stops displaying moving “o”.According to the analysis results, the system will automatically identify the possible User ID with most similar history records. Then the measuring results will be displayed sequentially three times .STEP 2: Stand still and keep full contact with the electrodes until the LCD stops displaying moving “o”.STEP 3: Your weight will be displayed followed by Body Fat, Total Body Water, Muscle Mass , CAL-MAX and the weight difference value. The data will be displayed three times. * If it fails to complete the analysis, the LCD will only display the weight data.(To find out the solutions, please refer to Troubleshooting for more details.)STEP 1: Step on the platform barefooted when the LCD displays “0.0”.1514First MeasurementDaily MeasurementStart MeasuringWhen your scale is successfully paired with your iPhone and the Bluetooth is ON, GBF-1319-B will process data transmission automatically. (Please refer to Data Transmission for more details.)• Position scale on a firm flat surface.• Press SET button.• While the user number of the latest measurement is flashing, select your user number by pressing or button. After 3s, the selected number is locked, the user’s personal data will be shown once, and then the scale shows zero reading.(Note: When the user number is flashing, if you press SET button again, it will enter the setting mode, after all the settings are finished, the settings will be shown once, and then display zero reading. )Start Measuring

When the system finds out two or more users with similar history records, it will notify you to choose between, for example, P1 and P2. You may press key for P1 and or key for P2. The measuring results will then be sorted into the User ID you selected and displayed sequentially three times.1716Start Measuring Data TransmissionIf it fails to identify the possible User ID, the LCD will only display the weight data. (To find out the solutions, please refer to Troubleshooting for more details.)When your scale is successfully paired with your iPhone and the Bluetooth is ON, GBF-1319-B will process data transmission instead. (Please refer to Data Transmission for more details.)With GBF-1319-B successfully pair-up with your iPhone, the measurement data will be transmitted to your mobile via Bluetooth.ONLY when the measuring results are attached to a specific User ID will it be transmitted to your mobile after measurement.The symbol will disappear after successful data transmission, and you may check your personal health data stored in your iPhone.If the data transmission fails, the symbol will remain. The pending measurement data will be temporarily kept in the scale and transmitted to your iPhone when next measurement is complete.Successful Bluetooth ConnectionData transmitting to wireless wellness system:-If SUCCEED, the symbol disappears;-If FAIL, the symbol remains.Data TransmissionCAUTIONInterference may occur in the vicinity of equipment marked with the following symbol . And the Analyzer may interfere vicinity electrical equipment.To enable the data transmission function, this product should be paired to a Bluetooth end at 2.4 GHz.How to mitigate possible interference?1. The range between the Analyzer and the Bluetooth end should be reasonably close, from 1 meter to 10 meters. Please ensure no obstacles between the Analyzer and the Bluetooth end so as to obtain quality connection.2. To avoid interference, other electronic devices (particularly those with Bluetooth transmission / Transmitter) should be kept at least 1 meter away from the Analyzer.

Error PromptError Description SolutionOverload. The device will power off in four seconds.Stop using this scale for measurement.Low Battery. The device will power off in four seconds.Replace all three batteries at the same time. Please purchase the authorized batteries for replacement.1918Measuring error. Stand still, and measure again.Failure of pairing up your scale with your smartphone.Please check below items:-Bluetooth is ON.-App Collector is ON.-Both devices are within the transmission distance of Bluetooth.Problem Root Cause SolutionIncorrect postureAbnormal measuring results:- Too high; OR- Too low; OR- Huge difference between two recent measurement.Please step on the platform barefooted and stand still.The device is located on the soft ground such as a carpet OR on a rugged surface.Please place the device on a flat, hard surface.When Measuring ...Either your hands or your feet are too dry.No display on LCD when the device powers on.Wipe your feet with a damp cloth, keeping them slightly damp when starting measurement.Batteries not yet installed.Worn batteries.Install the batteries.(Please refer to Insert the Batteries)Replace all three batteries at the same time. Please purchase the authorized batteries for replacement.Troubleshooting Troubleshooting

When carrying out usual maintenance, please ensure practice of the following Do’s and Don’ts:Transtek warrants its products free of defects in materials and workmanship in normal use for a period of TWO years from the date of retail purchase.This warranty does NOT cover damages caused by misuse or abuse, including but not limited to: Failure caused by unauthorized repairs or modifications;Damage caused by shock or drop during transportation;Failure caused by improper operation inconsistent with the instructions stated in this user manual;Malfunction or damage from failure to provide the recommended maintenance;Damage caused by improper use of power supply.Should this device require maintenance (or replacement at our option) under warranty, please deliver the original package to GUANGDONG TRANSTEK MEDICAL ELECTRONICS CO., LTD prepaid. Please return the store receipt (with the retail purchase date) and a note with reasons to return on it as well.SpecificationsMaintenanceWarrantyProduct NameDimensionBody Fat Analyzer (GBF-1319-B)Scale: 300x300x23mmPanel: 300x300x6mmNet Weight Approximately 1.85 kgDisplayDigital LCD V.A.: 76x51mmMeasurement Unit Kilogram / Stone/ PoundMeasurement Range 5kg to 180kg / 0st: 11lb to 28st: 5lb / 11lb to 397lbDivision 0.1kg / 0.2lbAccuracy 5-50kg: ±0.3kg;100-150kg: ±0.5kg;Working Environment Temperature: 10℃ to 40℃Humidity: ≤90% RHStorage Environment Temperature: -20℃ to 55℃Power Source 4.5V (3xAAA Batteries)Turn on Method SENSE ON technologyAuto-OFF The scale will turn off after about 10s if there is no operation.Accessories 1. 3xAAA batteries2. User ManualAbout the Accuracy of This ProductThis product passes strict inspection before delivery and therefore its accuracy is guaranteed by the manufacturer. Please refer to the above table for the descriptions on accuracy.This product is specially designed for body fat analysis as well as weight measurement. It should NOT be used by anyone during the process of transaction for verification of goods’ weight.GUANGDONG TRANSTEK MEDICAL ELECTRONICS CO., LTDZone A, 5/F., Investment Building, No. 12 Huizhan East Rd., Torch Development District, Zhongshan, 528437, Guangdong, ChinaTel: 86-760-88282982Website: http://www.transtek.cn 2250-100kg: ±0.4kg;150-180kg: ±0.7kgHumidity: 15%RH to 90% RHMode of Operation Continuous OperationProtection AgainstIngress of Water IPX0Software Version 1.0SpecificationsDO use a dry soft cloth to wipe the dust.DO use a wet soft cloth, dipped into water and wrung out, to wipe the dirt. Then use a dry soft cloth to dry up the device.DON’T wash the device with water or immerse it in water.DON’T use propellant, abrasive or other chemicals to wipe the dirt in avoidance of discolor or malfunction.DON’T disassemble this device. If you have any problems, please contact Transtek. (Please refer to Warranty for contact information)Maintenance23

Table of Body Fat Level (Unit: %)Table of Body Water Level (Unit: %)FCC Regulations Appendix24FCC User Guide InformationRadio Frequency Interface Requirements - FCCNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna;Increase the separation between the equipment and receiver;Connect the equipment into an outlet on a circuit different from that to which the receiver is connected;Consult the dealer or an experienced radio / TV technician for help.Radio Transmitters (Part 15)This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.FCC RF Exposure GuidelinesSafety InformationReducing RF Exposure - Use ProperlyOnly operate the device in accordance with the instructions supplied.This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possiblity of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.FCC RegulationsStandard for MenRatinglowNormalModerately HighHighAge20-29<13 <14 <16 <17 <1814-20 15-21 17-23 18-24 19-2521-23 22-24 24-26 25-27 26-28>23 >24 >26 >27 >2830-39 40-49 50-59 60+Standard for WomenRatinglowNormalModerately HighHighAge20-29<19 <20 <21 <22 <2320-28 21-29 22-30 23-31 24-3229-31 30-32 31-33 32-33 33-35>31 >32 >33 >34 >3530-39 40-49 50-59 60+a) The body fat percentage (%): 5%-60%/0.1%Source: University of Illinois Department of Food Science and Human Nutrition. Body Fat Percentage Calculator. www.ag.uiuc.edu/~food-lab/ai/bfc.htmlb) The body water percentage (%): 43%-73%/0.1%MenWomenBF % RANGE4 to 14%15 to 21%22 to 24%25 and over4 to 20%21 to 29%30 to 32%33 and over70 to 63%63 to 57%57 to 55%55 to 37%70 to 58%58 to 52%52 to 49%49 to 37%OPTIMAL TBW % RANGESource: Derived from Wang & Deurenberg: “Hydration of fat-free body mass”. American Journal Clin Nutr 1999,69833-841.25

Fat is essential for human body. It can not only store energy and protect viscera, but also regulate body temperature and maintain normal physiological function of human body. However, too much body fat is harmful to human body. It is always accompanied by Fatty Liver, diabetes, coronary heart disease, etc. Therefore self-measuring and self-monitoring body fat level are beneficial to your health. Since we can’t judge body fat level simply by our weight, this body fat analyzer GBF-1319-B, with BIA (Bio-impedance Analysis) technology applied, is an accurate device that offers a quick and comfortable way to obtain your body fat level. Health Tips - About Body FatMuscle Mass Percentage(Source: International Commission on Radiological Protection,1975)MenWomenApproximately 40% of total body weightApproximately 30% of total body weightBone Mass Percentage(Source: Rico et al.1993)The average bone mass percentage for both men and women is between 4 to 5%.EMC GuidanceTable 1 – Guidance and MANUF ACTURER’S declaration – ELECTROMAGNETIC EMISSIONSfor all ME EQUIPMENT and ME SYSTEMSGuidance and manufacturer’s declaration – electromagnetic emissions The device is intended for use in the electromagnetic environment specified below.The customer or the user of the device should assure that it is used in such anenvironment.Emissions test Compliance Electromagnetic environment-guidanceRF emissions CISPR 11 RF emissions CISPR 11 Harmonic emissions IEC 61000-3-2 Voltage fluctuations/ flicker emissions IEC 61000-3-3 Group 2 Class B Not applicableNot applicableThe device must emit electromagneticenergy in order to perform its intendedfunction. Nearby electronic equipment may be affected.Appendix Appendix26 27

Not applicableNot applicableNot applicableTable 2 – Guidance and MANUFACTURER’S declaration – electromagnetic IMMUNITY – for all ME EQUIPMENT and ME SYSTEMSCompliance levelElectromagnetic environment –guidance± 6 kV contact ± 8 kV air ro etercnoc ,doow eb dluohs sroolF ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30 %. a fo taht eb dluohs ytilauq rewop sniaMtypical commercial or hospital environment. ± 1 kV line(s) to line(s)± 2 kV line(s) to earth a fo taht eb dluohs ytilauq rewop sniaMtypical commercial or hospital environment. <5 % UT(>95 % dip in UT)for 0,5 cycle 40 % UT(60 % dip in UT)for 5 cycles 70 % UT(30 % dip in UT)for 25 cycles <5 % UT(>95 % dip in UT)for 5 s sdleif citengam ycneuqerf rewoP m/A 3 m/A 3 should be at levels characteristic of a typical location in a typical commercial or hospital environment. NOTE UT is the a.c. mains voltage prior to application of the test level. Mains power quality should be that of a typical commercial or hospital environment. If the user of the device requires continued operation during power mains interruptions, it is recommended that the device be powered from an uninterruptible power supply or a battery.Guidance and manufacturer’s declaration – electromagnetic immunity The device is intended for use in the electromagnetic environment specified below. Thecustomer or the user of the device should assure that it is used in such an environment.IMMUNITY testElectrostatic discharge (ESD) IEC 61000-4-2 Electrical fast transient/burst IEC 61000-4-4 Surge IEC 61000-4-5 Voltage dips, short interruptions and voltage variations on power supply input lines IEC 61000-4-11 Power frequency (50/60 Hz) magnetic field IEC 61000-4-8 IEC 60601 test level± 6 kV contact ± 8 kV air ± 2 kV for power supply lines ± 1 kV for input/output lines Not applicableTable 4 – Guidance and MANUFACTURER’S declaration – electromagnetic IMMUNITY – forME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTINGGuidance and manufacturer’s declaration – electromagnetic immunity IMMUN ITY test IEC 60601 TEST LEVE LCompliance levelElectromagnetic environment –guidanceConducted RF IEC 61000-4-6 Radiated RF IEC 61000-4-3 3 Vrms 150 kHz to 80 MHz 3 V/m 80 MHz to 2,5 GHz 3 V/m Recommended separation distance PV=d ]5,3[1P=d 2.333 800 MHz to 2,5 GHz where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres (m ). Field strengths from fixed RF transmitters, as deter-mined by an electromagnetic site survey,a should be less than the compliance level in each frequency range.bInterference m ay occur in the vicinity of equipment marked with the following symbol: NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadc ast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the device is used exceeds the applicable RF compliance level above, the device should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the device.b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than [V1] V/m. The device is intended for use in the electromagnetic environment specified below. Thecustomer or the user of the device should assure that it is used in such an environment.Portable and mobile RF communications equipment should be used no closer to any part of the device, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter.P=d 80 MHz to 800 MHz 1.167 Appendix Appendix28 29

Table 6 – Recommended separation distances between portable and mobile RF communications equipment and the ME EQUIPMENT or ME SYSTEM – forME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTINGRecommended separation distances between portable and mobile RF communications equipment and the device The device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the device can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the device as recommended below, according to the maximum output power of the communications equipment.Separation distance according to frequency of transmitter mRated maximum output power of transmitter W150 kHz to 80 MHz PV=d ]5,3[180 MHz to 800 MHz 800 MHz to 2,5 GHz 10,0 1,0 1 01 001For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic prop agation is affected by absorption and reflection from structures, objects and people. 0.2330.1170.7380.3692.3331.1677.3783.69023.3311.67Not applicableNot applicableNot applicableNot applicableNot applicableP=d 2.333P=d 1.167Appendix30

Navigation menu