Trango Systems M5830SSU 5Ghz Wireless Internet Access Point Subscriber Uni User Manual TrangoLINK Pro Instal Guide

Trango Systems Inc 5Ghz Wireless Internet Access Point Subscriber Uni TrangoLINK Pro Instal Guide

Installation Manual for Class I Permissive Change

TrangoLINK-10™ Wireless Ethernet Bridge PROFESSIONAL INSTALLATION GUIDE -draft-
RU Antenna Alignment TrangoLINK-10-EXT Professional Installation Guide Trango Broadband Wireless – Rev. A Page 2 Overview This manual covers basic configuration and installation of the TrangoLINK-10-EXT system which consists of two radios, M5830S-MU-EXT (Master Unit) and M5830S-RU-EXT (Remote Unit). Since these devices require manual maximum power limit settings (for 5.25-5.35 GHz U-NII band operation only), they are classified by the FCC as a professional install devices. To be in compliance with FCC guidelines, the radios must be installed with one of several approved antennas listed in this document. The M5830S-MU-EXTR and M5830S-RU-EXT are currently FCC certified for use with three external antennas. Antenna Part # Descrition Gain AD5830-24-D 18” DSS Dish 24 dBi AD5830-23-D 15” Flat Panel 24 dBi SPD3-5.2 3’ Dish from Radiowaves 30 dBi The M5830S-MU-EXT Master Unit works in conjunction with the M5830S-RU-EXT Remote Unit. Please see the TrangoLINK-10 User Manual for general information on overall system implementation, configuration, and management of these radios. The TrangoLINK-10 User Manual also covers many important aspects of radio configuration and management which is applicable to the TrangoLINK-10-EXT. FCC Information This device complies with Part 15 of FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in any particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of more of the following measures: 1) Reorient the antenna; 2) Increase the separation between the affected equipment and the unit; 3) Connect the affected equipment to a power outlet on a different circuit from that which the receiver is connected to; 4) Consult the dealer and/or experienced radio/TV technician for help. FCC ID: NCYM5830SSUEXT Canada: to be announced soon IMPORTANT NOTE: Intentional or unintentional changes or modifications must not be made unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty. To comply with FCC RF exposure requirements, the following antenna installation and device operating configurations must be satisfied. The antenna for this unit must be fixed and mounted on outdoor permanent structures with a separation distance of at least two meters from all persons. Furthermore, it must not be co-located or operating in conjunction with any other antenna or transmitter. Warranty Information Radios from Trango Broadband Wireless are warranted from one year from date of purchase. Please see www.trangobroadband.com for complete description of warranty coverage and limitations.
RU Antenna Alignment TrangoLINK-10-EXT Professional Installation Guide Trango Broadband Wireless – Rev. A Page 3 General Information Contents Each TrangoLINK-10-EXT kit comes equipped with a Master Unit (MU) and Remote Unit (RU), two power-over-Ethernet (PoE) J-Boxes, two AC adapters, and two mounting kits. The MAC ID and Serial # are printed on a label on the back of the radio. Antenna Connections The radio is equipped with two reverse-polarity SMA connectors on the side for attachment to an external antenna. Each SMA connector is labeled with either “V” for Vertical or “H” for Horizontal polarization. VERTICAL HORIZONTAL Connect each cable to the appropriate vertical and horizontal ports on both the antenna and the radio. Ethernet / Power Connections See the TrangoLINK-10 User Manual for detailed diagram for connecting radio to network or PC utilizing the power over Ethernet (PoE) J-Box and cat-5 cables. ! IMPORTANT: DO NOT APPLY DC POWER TO THE RADIO UNTIL THE ANTENNA IS ATTACHED OTHERWISE DAMAGE TO THE RADIO MAY OCCUR. Setting the Maximum RF Power The FCC allows a maximum EIRP of 1 watt (30 dBm) for devices transmitting in the 5.25 to 5.35 U-NII band. The M5830S-MU-EXT and M5830S-RU-EXT’s factory default maximum power settings for this band is +6 dBm. If the radio is to be equipped with Trango standard antennas AD5830-23-D or AD5830-24-D, no manual adjustment to the max power setting is required since radio power output plus antenna gain does not exceed 30 dBm. However, due to FCC restrictions the professional installer must manually reduce the maximum power for the 5.25 to 5.35 GHz U-NII band if a higher gain antenna is to be used. The table below shows the maximum power setting for the radio to achieve an EIRP of 1 watt (FCC limit). Only the antennas listed below are FCC Certified for use with the TrangoLINK-10-EXT.
RU Antenna Alignment TrangoLINK-10-EXT Professional Installation Guide Trango Broadband Wireless – Rev. A Page 4 Antenna Model Antenna Gain (incl/cable loss) Radio Max power setting AD5830-23-D +24 dBi +6 dBm AD5830-24-D +24 dBi +6 dBm SPD3-5.2 +30 dBi 0 dBm ? Note: that in all cases, Antenna Gain + Radio Max Power Setting is 30 dBm. Once set, the power leveling feature will still operate normally, but the maximum EIRP will never exceed 1 watt (30 dBm). The Max Power Setting command is only accessible from the command line and is not available on the HTTP Browser interface. The telnet or serial port command to change the maximum power is: uniimaxpower <max power in dBm> The flash memory must be updated after running the command. save systemsetting The command must be run prior to installing the antenna and while the Opmode is OFF. Example: To set the max power setting for the AD5830-23-D: #> uniimaxpower 6 #> save systemsetting ? Note: The maximum RF power may be left at +22 dBm for the 5.725 to 5.85 GHz ISM band regardless of which FCC Certified antenna is used. No manual setting is required.
RU Antenna Alignment TrangoLINK-10-EXT Professional Installation Guide Trango Broadband Wireless – Rev. A Page 5 Radio Hardware Installation The M5830S-MU-EXT and M5830S-RU-EXT may be installed on a pole or a flat surface per the drawings below: TO ANTENNA TO ANTENNABOLTS FOR MOUNTING TO WALLNOT SUPPLIEDBRACKETS (SUPPLIED)POLE MOUNTING WALL MOUNTING Radios should always be mounted with Ethernet and RJ11 ports at the bottom. See the TrangoLINK-10 User Manual for grounding and additional weatherproofing guidelines. In addition to the guidelines listed in the TrangoLINK-10 User Manual, installers must cover cable-SMA connectors (both ends) with heat-shrink to provide weatherproofing of the RF cable connectors.
RU Antenna Alignment TrangoLINK-10-EXT Professional Installation Guide Trango Broadband Wireless – Rev. A Page 6 AD5830-24-D DSS STYLE ANTENNA See diagram below for proper installation of the AD5830-24-D These antennas are designed primarily for low rise building installations only. Do not install in an area where high (>70 mph) winds are expected. NOTE: Optimal alignment of this dish (to radio at horizon) is 20? below vertical.
RU Antenna Alignment TrangoLINK-10-EXT Professional Installation Guide Trango Broadband Wireless – Rev. A Page 7 AD5830-23-D PANEL ANTENNA To install the AD5830-23-D Panel antenna please see the drawing below: HEATSHRINK HERE AFTERTIGHTENING CONNECTOR4X 1) HAND TIGHTEN ALL THREAD INTO ENCLOSURE 2) TORQUE KEP NUTS (8-12 IN-LBS) 3) ATTACH TO POLE WITH "V" BRACKET 4) ATTACH KEP NUTS TO "V" BRACKET AND TORQUEHARDWARE TO ATTACH BRACKETTO WALL NOT SUPPLIED4X ATTACH WALL BRACKET WITH 5/16-18 X .500 HEX HEAD AND LOCK WASHERSHEAT SHRINK HERE AFTERTIGHTENING CONNECTORPOLE MOUNTINGWALL MOUNTING27°11°61°25°POLE MOUNT("V") BRACKETWALL MOUNT BRACKET2X CA-9023A-9014 RADIOWAVES SPD3-5.2 PRIME FOCUS DISH ANTENNAS The SPD3-5.2 from Radiowaves, Inc. is a parabolic prime focus dish antenna designed for long range applications and tower installations. These antennas are designed for superior performance in long range applications and tower installations that may be subject to high winds. Radomes are available from Radiowaves for installations subject to extreme weather. Contact Radiowaves, Inc. (www.radiowavesinc) for more information. The SPD3-5.2 is equipped with a standard “N” Female RF Connector interface. A special cable assembly is required to connect this antenna to the Trango M5830S-SU-EXT’s reverse polarity SMA Female connector. Recommended Cable Assembly: REVERSE POLARITY SMA MALE TO STANDARD N MALE 50 OHM, RG142B/U COAX, DOUBLE SHIELDED. Length: 24” – 48”. ? Note: To minimize loss, use the shortest cable length possible. Pre-Assembled Cable Assemblies are available from Pasternack Enterprises www.pasternack.com. Model No. PE34361-24 24” REVERSE POLARITY SMA MALE TO STANDARD N MALE Model No. PE34361-36 36” REVERSE POLARITY SMA MALE TO STANDARD N MALE
RU Antenna Alignment TrangoLINK-10-EXT Professional Installation Guide Trango Broadband Wireless – Rev. A Page 8 Model No. PE34361-48 46” REVERSE POLARITY SMA MALE TO STANDARD N MALE See the Radiowaves SPD3-5.2 User’s Manual for detailed hardware installation instructions. Remote Unit Antenna Alignment To align the RU antenna for optimal performance, follow the procedure outlined in the TrangoLINK-10 User Manual. This procedure is also included below for your convenience. The same procedure applies to both the P5830S-RU and the P5830S-RU-EXT. Once the RU’s antenna is mounted and aimed in the general direction of the MU, it is time to perform an RSSI test to determine the signal strength from the MU, and to precisely align the RU antenna for maximum signal strength. RU Antenna Alignment Procedure 1. Ensure MU is in opmode “ON” 2. Telnet into the RU (while in opmode “OFF”) or access the radio via hyperterminal/serial port. 3. Type command RSSI <channel> <polarization> - Example RSSI 3 V (chan. 3, vertical polarization) 4. Telnet session screen will begin a continuous readout of the received signal strength. 5. As you read the RSSI reading, move the antenna in the horizontal and vertical planes until the maximum RSSI reading is achieved. For short links you can expect an RSSI of –60 dBm or better. For longer links and RSSI of –75 dBm is acceptable. Any RSSI of less than –80 dBm may be too weak for the radios to reliably associate and pass data. 6. If it is not possible to receive an adequate RSSI reading, it may be necessary to reorient the MU (up/down, left/right), to increase the output power of the MU, or to move the RU to a location with better line-of-sight conditions to the MU. Once you are satisfied with the RSSI reading, tighten down the antenna in the optimum position. To stop the RSSI continuous readout, hit SPACE ENTER. ? Note: The amber light on the bottom of the RU will also indicate RSSI according to the following parameters: RSSI < -80dBm not lit RSSI > -80dBm blinking. RSSI ? -65dBm solid. (blink rate increases with signal strength.)
RU Antenna Alignment TrangoLINK-10-EXT Professional Installation Guide Trango Broadband Wireless – Rev. A Page 9 Specifications Radio Transmit Specifications Frequencies: Storable Channels: 30 memory locations Channel spacing: Low Band: 5.260 to 5.340 GHz in 1 MHz channel increments High Band: 5.736 to 5.836 GHz in 1 MHz channel increments Default Channels- Channel 1: 5.736 GHz Channel 2: 5.756 GHz Channel 3: 5.776 GHz Channel 4: 5.796 GHz Channel 5: 5.816 GHz Channel 6: 5.836 GHz Channel 7: 5.260 GHz Channel 8: 5.280 GHz Channel 9: 5.300 GHz Channel 10: 5.320 GHz Channel 11: 5.340 GHz Channel 12-30: Un-programmed Radio RF Conducted Power: Low Band: Max: +6 dBm +/- 2 dB Min: -8 dBm +/- 2 dB High Band: Max: +22 dBm +/- 2 dB Min: -8 dBm +/- 2 dB EIRP Max: +52 dBm High band with SPD3-5.2 antenna, +46 dBm with 24 dBi antenna. +30 dBm Low band Maximum (all antennas) Freq. Stability: .00025 % PLL Stabilized (2.5 ppm) over temp Freq. Plan: Single upconversion, 480 MHz IF Modulated BW: 22 MHz (null to null, 20 dB) 2nd Harmonic atten: Per CFR47 part 15.205 LO Supression: Per CFR47 part 15.205 Symbol Rate: 1.375 MSPS Error Correction: None Modulation: 1 Mbps DBPSK for header, 11 Mbps CCK spread spectrum for payload Receiver Section Cascade Noise Figure: < 6 dB Sensitivity: - 83 dBm typical-1600 byte packet (1E10-6 BER) - 87 dBm typical-64 byte packet Adj. Channel Rejection: > 20 dB for 10 % PER Image Rejection: > 60 dB for 10% PER Frequency Plan: Single conversion, IF at 480 MHz LO stability: .00025% PLL stabilized (+/-2.5ppm) over temperature range Data Input Section Data Rate (User): Up to 10 Mbps Sustained throughput Format: 10/100 BaseT IEEE 802.3 Ethernet compliant Ethernet packet: Up to 1600 byte long packets Power Input Voltage: Input voltage range at unit is 10.5 VDC to 24 VDC max
RU Antenna Alignment TrangoLINK-10-EXT Professional Installation Guide Trango Broadband Wireless – Rev. A Page 10 Power is supplied on Ethernet cable using junction box provided with up to 330 foot 24 AWG STP cable. Current Cons.: 575 mA in transmit mode at max power using 20 V standard adapter (11.5W) 500 mA in receive mode using 20 V standard adapter (10 W) Data Output Section Data Rate (User): 10 Mbps Maximum sustained throughput Format: 10/100 BaseT IEEE 802.3 Ethernet compliant Ethernet Protocols: TCP/IP, Telnet, TFTP, UDP, HTTP Physical Interfaces Serial Interface: Shielded RJ11 connector LAN Interface: Shielded RJ45 connector Power: Carried on 4 unused pins of Ethernet cable Mechanical and Environmental General Material: Powdercoated Aluminum base with polycarbonate radome Size: 12.5”x5”x8” including mounting studs Weight: 4 lb Mounting: Custom mounting bracket with azimuth-elevation adjustment. Environmental Operating Temp: -40 to 60 deg C Storage: -40 to 85 deg C NEMA Rating: NEMA 4 Standard Power Supply 20 Volt DC Power adapter and J-Box supplied with product. Type: Linear wall mount transformer Input: 120 VAC Output: 20 VDC +/- 1 V Max current: 1200 mA FCC Compliance Subpart B Class B Digital device verification Subpart C FCC 15.203 Antenna connection requirement – non-standard connection FCC 15.209 Unwanted emissions below 1GHz - FCC 15.207(a) AC conducted emissions 450Khz to 30 MHz FCC 15.205 Restricted bands (LO and harmonics)= 54 dBuV average @3 meters EN 301 489-1 Part 7.2 - RF Immunity AD5830-24-D DSS Style dish for M5830S-SU-EXT Type DSS Offset (Satelite TV style) 18" (see drawing) Polarization Vertical, horizontal electronically selectable Frequency 5.2 to 5.9 GHz Gain +24 dBi Azimuth Beamwidth 9 degrees Elevation Beamwidth 9 degrees Mount Standard DSS Style U-Bolt Mount AD5830-23-D Patch Antenna for M5830S-SU-EXT Type Patch - 15" Square
RU Antenna Alignment TrangoLINK-10-EXT Professional Installation Guide Trango Broadband Wireless – Rev. A Page 11 Polarization Vertical, horizontal electronically selectable Frequency 5.2 to 5.9 GHz Gain +24 dBi Azimuth Beamwidth 9 degrees Elevation Beamwidth 9 degrees Mount Heavy Duty Universal Mount. Radio Waves SPD3-5.2 Parabolic Dish for M5830S-SU-EXT Type Parabolic Prime Focus 36" Dish Polarization Vertical, horizontal electronically selectable Frequency 5.2 to5.9 GHz Gain +31 dBi (30 dBi with Cable Loss) Azimuth Beamwidth 4.2 degrees Elevation Beamwidth 4.2 degrees Cross Polarization 30 dB Front/Back Ratio 40 dB

Navigation menu