Topcon RF10 2.4GHz BAND DATA COMMUNICATION MODULE User Manual RF 10

Topcon Corporation 2.4GHz BAND DATA COMMUNICATION MODULE RF 10

manual

10-JUNE-2011 TOPCON CORPORATION RF-10 User Manual Rev. 1 Page 1 of 8 RF-10 User Manual Confidential
10-JUNE-2011 TOPCON CORPORATION RF-10 User Manual Rev. 1 Page 2 of 8 List of Contents 1. General 1.1 Overview 1.2 Features 1.3 Application 1.4 Interface connecter pin assignment 1.5 Outline View 1.6 Package Dimensions 2. Characteristics 2.1 Electrical Characteristics 2.2 RF Characteristics 3. Notes
10-JUNE-2011 TOPCON CORPORATION RF-10 User Manual Rev. 1 Page 3 of 8 1 General 1.1 Overview This specification covers RF-10 Data Radio Unit, which complies with ARIB STD T-66, FCC Part 15 247 RSS-210 and ETSI EN 300 400. This unit consist of Texas CC2500 radio IC and for Radio Data communication in 2.4GHz band. All detailed specification may be changed without notice. CC2500 TEXAS RADIO IC UART Interface 2.4GHz Antenna
10-JUNE-2011 TOPCON CORPORATION RF-10 User Manual Rev. 1 Page 4 of 8 1.2 Features • Radio Data rate up to 32kbps. • Support Slow Hopping 22channels in 2.401GHz ~ 2.479.75GHz • Ultra Low Power Consumption • RoHS Compliant • Support USART connection speed up to 115.2kbps • Small Package Size (38.7 x 19.0 x 5.9) • Integrated 26MHz Crystal Unit 1.3 Application • Radio Data Modem • Wireless Controller • Wireless Data Logger • Wireless Security Sensor 1.4 Interface connecter pin assignment TOP Side View of RF-10 1.2. VB (Power In) 3.4. GND (Power GND) 5.6. PWR CONT (Unit Power Control) 7.8. RXD(UART RXD) 9.10. SCLK(Clock In) 11.12. TXD(UART TXD) 13.14. GDO2 MONI(Not Used) 15.16. GDO0 MONI(Not Used) 17. CS (Chip Select) 18. Cont1(RF In / Out Select) 1.5 19. Cont2(RF In / Out Select) 20. Cont3(RF Amp Switch)) 1219 20
10-JUNE-2011 TOPCON CORPORATION RF-10 User Manual Rev. 1 Page 5 of 8 1.5 Outline View 1.6 Package Dimensions Left Side View Top View Right Side ViewSide View Weight 6g 38.7 19.0 5.9 Interface connector Pattern Antenna
10-JUNE-2011 TOPCON CORPORATION RF-10 User Manual Rev. 1 Page 6 of 8 2. Characteristics 2.1 Electrical Characteristics Absolute Maximum Rating Rating Minimum Typical Maximum Unit Supply Voltage 3.2 3.5 6.5 V Operating Temperature Range -20 25 55 C RX Current consumption 36 mA TX Current consumption 40 mA 2.2 RF Characteristics Transmitter Specification Condition Min. Typ. Max. Output Transmit Power Normal -1dBm Frequency Range Normal GHz 2.401 2.4797520dB Bandwidth Normal MHz 0.1 Modulation Characteristics Normal MHz 0.05 Carrier Frequency Drift -20 ~ +50 C 2.5ppm Receiver Specification Condition Min. Typ. Max. Sensitivity BER 0.1% -90dBmMaximum Input Level Normal -20dBmAdjacent Channel rejection Normal 18dB
10-JUNE-2011 TOPCON CORPORATION RF-10 User Manual Rev. 1 Page 7 of 8 3. Notes FCC Statements: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT CAUTION: This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. End user cannot modify this transmitter device. Any unauthorized modification made on the device could avoid the user's authority to operate this device. CAUTION: To comply with FCC RF exposure compliance requirements, a separation distance of at least 20cm must be maintained between the antenna of this device and all persons. The following sentence has to be displayed on the outside of the device in which the transmitter module is installed: “Contains FCC ID:H5P-RF10 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
10-JUNE-2011 TOPCON CORPORATION RF-10 User Manual Rev. 1 Page 8 of 8 IC Statements: The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. This device complies with RSS 210 of Industry Canada “IC”. “Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.” "The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website www.hc-sc.gc.ca/rpb" L’ utililisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. "The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website www.hc-sc.gc.ca/rpb" “To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.” The following sentence has to be displayed on the outside of the device in which the transmitter module is installed: “Contains IC:6050A-RF10

Navigation menu