Top Victory Electronics CM995T Color Monitor User Manual S995T EPI

Top Victory Electronics (Taiwan) Co Ltd Color Monitor S995T EPI

Exhibit 7 The user manual of EUT

Your Work Never Looked BetterPlug & Play Drivers for the AOC Spectrum Series Monitors are availableat : www.epius.com9Glr/9GlrAUSER MANUALTABLE OF CONTENTSFOR YOUR SAFETY --------------------------------------------------1SAFETY PRECAUTIONS -------------------------------------- 2BEFORE YOU OPERATE THE MONITOR ---------------------- 3FEATURES -------------------------------------------------------- 3PACKING LIST --------------------------------------------------- 3INSTALLATION INSTRUCTIONS --------------------------- 3CONTROLS AND CONNECTORS -------------------------- 4OPERATING INSTRUCTIONS ------------------------------------- 5GENERAL INSTRUCTIONS ---------------------------------- 5HOW TO ADJUST A SETTING ------------------------------ 7ADJUSTING THE PICTURE ---------------------------------- 7POWER MANAGEMENT FEATURE -----------------------9PLUG AND PLAY ------------------------------------------------10TECHNICAL SUPPORT(FAQ) -------------------------------------12APPENDIX ---------------------------------------------------------------13SPECIFICATIONS -------------------------------------------13-14FACTORY PRESET TIMING TABLE -----------------------15CONNECTOR PIN ASSIGNMENT --------------------------15Thank you very much for choosing the AOC Color Monitor.We recommend that you take a few minutes to read carefully through thisbrief but comprehensive manual before installing and switching on themonitor. Please keep this manual in a safe place for you future reference.
1Before operating the monitor please read this manual thoroughly. Thismanual should be retained for future reference.FCC Class B Radio Frequency Interference StatementWARNING: (FOR FCC CERTIFIED MODELS)NOTE: This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses andcan radiate radio frequency energy, and if not installed and used inaccordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:1. Reorient or relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.4. Consult the dealer or an experienced radio/TV technician for help. NOTICE1. The changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate theequipment.2. Shielded interface cables and AC power cord, if any, must be used inorder to comply with the emission limits.3. The manufacturer is not responsible for any radio or TV interferencecaused by unauthorized modification to this equipment. It is theresponsibilities of the user to correct such interference.As an ENERGY STAR Partner Envision Peripherals, Inc. has determinedthat this product meets the ENERGY STAR guidelines for energy efficiency. WARNING :To prevent fire or shock hazard, do not expose the monitor to rain ormoisture. Dangerously high voltages are present inside the monitor. Do notopen the cabinet. Refer servicing to qualified personnel only.
2 lDo not use the monitor near water, e.g. near a bathtub, washbowl,kitchen sink, laundry tub, swimming pool or in a wet basement.lDo not place the monitor on an unstable cart, stand, or table. If themonitor falls, it can injure a person and cause serious damage to theappliance. Use only a cart or stand recommended by the manufacturer orsold with the monitor. If you mount the monitor on a wall or shelf, use amounting kit approved by the manufacturer and follow the kit instructions.lSlots and openings in the back and bottom of the cabinet are provided forventilation. To ensure reliable operation of the monitor and to protect itfrom overheating, be sure these openings are not blocked or covered. Donot place the monitor on a bed, sofa, rug, or similar surface. Do not placethe monitor near or over a radiator or heat register. Do not place themonitor in a bookcase or cabinet unless proper ventilation is provided.lThe monitor should be operated only from the type of power sourceindicated on the label. If you are not sure of the type of power supplied toyour home, consult your dealer or local power company.lThe monitor is equipped with a three-pronged grounded plug, a plug witha third (grounding) pin. This plug will fit only into a grounded power outletas a safety feature. If your outlet does not accommodate the three-wireplug, have an electrician install the correct outlet, or use an adapter toground the appliance safely. Do not defeat the safety purpose of thegrounded plug.lUnplug the unit during a lightning storm or when it will not be used forlong periods of time. This will protect the monitor from damage due topower surges.lDo not overload power strips and extension cords. Overloading can resultin fire or electric shock.lNever push any object into the slot on the monitor cabinet. It could shortcircuit parts causing a fire or electric shock. Never spill liquids on themonitor.lDo not attempt to service the monitor yourself; opening or removingcovers can expose you to dangerous voltages and other hazards. Pleaserefer all servicing to qualified service personnel.lTo ensure satisfactory operation, use the monitor only with UL listedcomputers which have appropriate configured receptacles markedbetween 100 - 240V AC, Min. 2.5A.PRECAUTIONS
3BEFORE YOU OPERATE THE MONITOR FEATURES•48.3cm(19”) Color Monitor•Crisp, Clear Display for Windows•Supports Resolutions up to 1600 5 1200•Power Management•Space Saving, Compact Case Design The product package should include the following items:1. Monitor2. Owner's Manual3. Power Cord4. Swivel Base5. Audio Cable/DC Power Cable ( for 9GlrA only ) INSTALLATION INSTRUCTIONS. SWIVEL BASETo attach the swivel base to the monitor, do the following:•Carefully turn the monitor on its side or upside down. ( see figure 1 )•Locate the cavities at the bottom front of the monitor.•Insert the pegs on the swivel base into these cavities. Push the swivelbase forward until the swivel base locks in place.•To remove the swivel base, hold the bottom of the swivel base, then pushit out.Install Remove Install Remove9Glr 9GlrAFigure 1 Installing and Removing the Swivel BaseFEATURESCHECKING THE CONTENTS OF THE MONITOR PACKAGEINSTALLATION INSTRUCTIONS
4 POWER CORDPower Source:1. Make sure the power cord is the correct type that required in your area.2. This monitor has a universal power supply that allows operation in either100/120V AC or 220/240V AC voltage area ( No user adjustment isrequired. )3. Connect the power cord into your monitor’s power input socket, and thenplug the other end into a 3-pin AC power outlet. The power cord may beconnected to either a wall power outlet or the power outlet socket on yourPC, depending on the type of power cord supplied with your monitor. VIDEO CABLEConnecting the Video Cable: the monitor comes with a built-in video cable.Plug the signal cable′s 15-pin connector into the computer's video port andtighten the two screws on the cable connector. (see figure 2)Caution: Don’t bend the signal cable, otherwise it will break the inner wire.Connecting the Power Cord: Plug the power cord into the monitor's ACpower socket. Then plug the power cord into a grounded AC outlet or UL-approved power strip or the power output socket on your PC.Caution: If the AC outlet is not grounded, install the proper groundingadapter (not supplied).Connecting the Audio Cable ( 9GlrA only ): Plug audio cable between thecomputer multi-media (or sound) card's audio output and monitor's audioinput.Connecting the DC Power Cable ( 9GlrA only ): Plug DC power cablebetween monitor to swivel base for audio power13425 9Glr 9GlrAFigure 2 Connecting Cables1. Power Cord 4. PC Audio Output2. Signal Cable 5. DC Output3. VGA Card AdapterCONTROLS AND CONNECTORS
5OPERATING INSTRUCTIONS The other control knobs are located at the base of the monitor (See Figure3). By changing these settings, the picture can be adjusted to your personalpreferences.•The power cord should be connected.•Connect the video cable from the monitor to the video card.•To turn the monitor on, press the standby POWER switch to ON position.The power indicator will light up.•Your monitor features a unique quick switch system which provides apicture within seconds after the monitor is switched on.1234123456789Glr 9GlrAFigure 3 External Control Knob EXTERNAL CONTROLS9Glr 9GlrA1. OSD Exit 1. OSD Exit 5.Earphone Jack2. Shuttle Knob 2. Shuttle Knob 6.Volume3. Standby Power 3. Standby Power 7. Audio Power IndicatorON/OFF Switch ON/OFF Switch4. Power Indicator 4. Power Indicator 8. Audio Power ON/OFFGENERAL INSTRUCTIONS
6 FRONT PANEL CONTROL•Standby power key :When pressed, the monitor enters the off mode, and the LED turnsorange. Press again and hold to restore normal status.•Shuttle Knob :The Shuttle Knob is used to control the monitor functions. Rotate toswitch functions or adjust settings. Press to select or execute a function .•OSD Key :The OSD Key is used to activate the OSD window, or to exit the OSDwindow and save the settings.•Power Indicator :Green — Power On mode.Orange — Stand-by mode, Suspend mode, or Off mode. SWIVEL BASE CONTROL (9GlrA ONLY ) :•Audio Power ON or OFF Audio Power•Power IndicatorGreen — Audio Power ON.•VolumeAdjustable Audio volume. NOTES•Do not install the monitor in a location near heat sources such asradiators or air ducts , or in a place subject to direct sunlight , orexcessive dust or mechanical vibration or shock.•Save the original shipping carton and packing materials, as they willcome in handy if you ever have to ship your monitor.•For maximum protection, repackage your monitor as it was originallypacked at the factory.•To keep the monitor looking new, periodically clean it with a soft cloth.Stubborn stains may be removed with a cloth lightly dampened with amild detergent solution. Never use strong solvents such as thinner,benzene, or abrasive cleaners, since these will damage the cabinet. As asafety precaution, always unplug the monitor before cleaning it.
7 1. Press the Shuttle Knob or OSD Key to make the OSD window appear.See figure 4.2. Rotate the Shuttle Knob to select the desired function. See figure 4.3. Press the Shuttle Knob again to select the function that you want toadjust.4. Rotate the Shuttle Knob to change the settings of the current function.5. When the OSD window is active, it shows the input signal timing. The"H" stands for the horizontal frequency and "V" for the vertical frequency.6. To exit and save, either press the OSD Key, select the exit function, orleave the monitor alone for 10 seconds. If you want to adjust any otherfunction, repeat steps 2-4.70V: 85Hz9300 6500H: 68.8KHzContrastFigure 4 The OSD Message The description for function control LEDS1. CONTRAST Adjust the picture contrast.2. BRIGHTNESS Adjust the picture brightness.3. H- CENTER Adjust the horizontal position of the picture.4. H- SIZE Adjust the picture’s horizontal size.5. V- CENTER Adjust the vertical position of the picture.ADJUSTING THE PICTUREHOW TO ADJUST A SETTING
86. V- SIZE Adjust the picture’s vertical size.7. ZOOM Adjust the picture’s horizontal and verticalsize simultaneously.8. PINCUSHION Adjust the pincushion and barrel9. TRAPEZOID Adjust the picture’s trapezoid distortion.10. PIN-BALANCE Adjust to compensate the pincushionunbalance.11. PARALLELOGRAM Adjust the picture to be a rectangle.12. ROTATION Adjust the picture tilt to horizontal position.13. 6500°K/9300°K( COLORTEMPERATURE )The color temperature for 6500°K isx=0.313, y=0.329 and 9300°K is x=0.283,y=0.297. It presents two different color setson the screen. You can select 9300°K or6500°K by pressing the Shuttle Knob.14. USER COLOR( Red / Blue ) If the 9300°K normal white or 6500°Kwarmer white do not satisfy your desire,properly adjust R . B GAIN controls to obtainyour optimum whiteness level.15. DEGAUSS If color impurity occurs when moving orswiveling the monitor, press the Shuttle Knoband degauss to fix the picture condition.16. MOIRE REDUCE Moire is the result of interference betweenthe phosphor layout and the video signal. Insome cases, you may find the moire verynoticeable. Press the Shuttle Knob to enter inthe moire reduce setting. Please adjust thelevel to the optimum condition. Note: Toohigh of a setting will cause the picture toshake.17. RECALL Press RECALL to restore the monitor tofactory settings.18. EXIT Close OSD window.
9 The power management feature of this product complies with every powersaving requirements of ENERGY STAR and VESA DPMS when activated,it automatically reduces unnecessary power consumption of the monitorwhen your computer is not in use.To use the feature, the monitor needs to be connected to a VESA DPMScomputer. There are three power management modes available, these aredescribed below. The required settings, including the timer setting, should bemade by the computer.•Stand-by ModeWhen the H-sync signal from the computer is off, the monitor enters intoStand-by Mode which reduces the power consumption to less than 15W.The screen becomes dark, and the power indicator turns to orange. FromStand-by Mode, the screen reappears instantaneously when the keyboardor the mouse is touched again.•Suspend ModeWhen the V-sync signal from the computer is off, the monitor enters intoSuspend Mode which reduces the power consumption to less than 15W.The screen becomes dark, and the power indicator turns to orange. FromSuspend Mode, the screen reappears instantaneously when the keyboardor the mouse is touched again.•Active-off ModeWhen both the H and V sync signals from the computer are off, themonitor enters into Active-off Mode which reduces the powerconsumption to less than 8W. The screen becomes dark, and the powerindicator turns to orange. From Active-off Mode, the screen reappearsinstantaneously when the keyboard or the mouse is touched again.•The power-saving mode can be indicated by the light-emitting diode (LED)on the front panel: Signal PowerMode Cable H-Sync V-Sync Video Indicator ConsumptionOn*Attached Yes Yes Active Green ≤ 130 WStand-by Attached No Yes Blank Orange ≤ 15 WSuspend Attached Yes No Blank Orange ≤ 15 WOff Attached No No Blank Orange ≤ 8 WPOWER MANAGEMENT FEATURE
10 FEATURESGreen monitor•The monitor has a power saving function that conforms to the VESADPMS standard. This feature will only work if your PC is a green PC. Thisfeature is similar to a screen saver, except that your monitor will turn it offinstead of activating the screen saver.To activate this feature in Windows® 98 :In Windows® 98, this feature can be activated and customized under thescreen saver setting of the display properties.1. Right click on the desktop and choose Properties.2. Click on the tab that says Screen Saver. If your system supports GreenPC, there will be a section entitled “Energy Saving Features of Monitor.”If there isn’t a section like that, then your PC does not support GreenMonitor. The monitor will behave just like a normal monitor, so you willhave to turn it off manually to save energy.3. In the “Energy Saving Features of Monitor” sections are two boxes,Standby and Shut off. To activate either one, click the box next to eachone.4. You can specify the amount of inactive time before your monitor entersstandby mode or shuts off. Plug & Play DDC1/2B FeatureThis monitor is equipped with VESA DDC1/2B capabilities according to theVESA DDC STANDARD. It allows the monitor to inform the host system ofits identity and, depending on the level of DDC used, communicate additionalinformation about its display capabilities. The communication channel isdefined in two levels, DDC1 and DDC2B.The DDC1 is a unidirectional data channel from the display to the host thatcontinuously transmits EDID information. The DDC2B is a bidirectional datachannel based on the I²C protocol. The host can request EDID informationover the DDC2B channel.PLUG AND PLAY
11THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE ISNO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TOOPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.This monitor meets the Power Management standards as set by the VideoElectronics Standards Association (VESA) and/or the United StatesEnvironmental Protection Agency (EPA) and The Swedish ConfederationEmployees ( NUTEK ). This feature is designed to conserve electrical energyby reducing power consumption when there is no video input signal present.When there is no video input signal this monitor, following a time-out period,will automatically switch to an OFF mode. This reduces the monitor's internalpower supply consumption. After the video input signal is restored, full poweris restored and the display is automatically redrawn. The appearance issimilar to a "Screen Saver" feature except the display is completely off. Thedisplay is restored by pressing a key on the keyboard, or clicking the mouse. USING THE RIGHT POWER CORD :The accessory power cord for the Northern American region is the walletplug with NEMA 5-15 style and is UL listed and CSA labeled. The voltagerating for the power cord shall be 125 volts AC.Supplied with units intended for connection to power outlet of personalcomputer: Please use a cord set consisting of a minimum No. 18 AWG, typeSJT or SVT three conductors flexible cord. One end terminates with agrounding type attachment plug, rated 10A, 250V, CEE-22 maleconfiguration. The other end terminates with a molded-on type connectorbody, rated 10A, 250V, having standard CEE-22 female configuration.
12TECHNICAL SUPPORT (FAQ)Problem & Question Possible SolutionPower LED is not on *Power Cord should be connectedNo Plug & Play *Check if the PC system is Plug & Playcompatible*Check if the Video Card is Plug & Playcompatible*Check if the D-15 plug pin of Video Cableis bent*Make sure the AOC Monitor Drivers areinstalled(AOC Monitor Drivers are available at:www.epius.com)No picture *Computer Power Switch should be in theON position*Computer Video Card should be snuglyseated in its slot*The Signal Cable should be completelyconnected to the computer*Check the color of the Power LEDindicator. If it is orange, then the monitorand the PC system are in power-savingmode. You need press your keyboard ormove the mouse to reactivate thesystem.Picture is fuzzy *Adjust the Contrast and BrightnessControls.Picture bounces or a wavepattern is present in the picture *Move electrical devices that may causeelectrical interference.Monitor is stuck in “PowerSaving Mode”*Make sure monitor’s video cable isproperly connected to the computer.*Inspect monitor’s video cable and makesure none of the pins are bent.*Make sure computer is operational byhitting the CAPS LOCK key on thekeyboard while observing the CAPSLOCK LED. The LED should either turnON or OFF after hitting the CAPS LOCKkey.Missing one of the primarycolors (RED, GREEN, orBLUE)*Inspect the monitor’s video cable andmake sure that none of the pins arebent.North America technicalsupport telephone number: 1-800-343-5777
13APPENDIX SPECIFICATIONSCRT Size 48.3cm(19"), 29mm neck,CRT Viewable ImageSize 45.7cm (18"), diagonalType 0.26 mm dot pitch.Video 0.7Vpp, R,G,B AnalogInput Separate Sync. TTL LevelH./V.- Sync. Positive / NegativeScanning H-Frequency 30kHz - 95kHzFrequency V-Frequency 50Hz-160HzMax. Resolution 1600 x 1200Video Dot Rate 200MHzFactory Preset mode :8UserProgrammable mode : 12Power Source Universal AC 100 - 240V,50Hz / 60HzOperating 0ºC to 40ºC ambientHumidity 10% to 85%relative, non-condensingDimensions9Glrs Monitor & Base 460(W) × 466(H) × 470(D)mm9GlrsA: Monitor & Base 460(W) × 503(H) × 470(D)mmWeight9Glr: Unit (net) 20kgs ( Net )9GlrA: Unit (net) 20.8kgs ( Net )Signal Cable: Attached Mini D-sub 15 Male460466470(in mm)9Glr
14Switch •Shuttle Knob•Standby Power Switch•OSD Key•Volume(9GlrA)External Controls: Functions •Contrast•Brightness•H-Center•H-Size•V-Center•V-Size•ZOOM•Pincushion•Trapezoid•Pin-Balance•Parallelogram•Rotation•6500°K•User Color•9300°K•Degauss•Moire Reduce•Recall•ExitPlug & Play DDC1/2BPower Management EPA, VESA DPMSPower Consumption ( Maximum ) 130 WattsPre-set Display Area 346mm x 260mmAudio Output(for 9GlrA only) Rated Power 1W rms(Per channel)Regulatory Compliance UL, CSA, FDA, FCC, TÜV/GS, CE,TCO’92 (TCO’95/TCO’99)503460 470(in mm)
159GlrASTANDARD RESOLUTION HORIZONTALFREQUENCY VERTICALFREQUENCYVGA 720 × 400 31.5kHz 70HzVGA 640 × 480 31.5kHz 60HzVESA/85 640 × 480 43.3kHz 85HzVESA/85 800 × 600 53.7kHz 85HzVESA/85 1024 × 768 68.7kHz 85HzVESA/85 1280× 960 85.9kHz 85HzVESA/85 1280× 1024 91.1kHz 85HzVESA/75 1600× 1200 93.8kHz 75Hz1 561011 1515 - Pin Color Display Signal CablePIN NO. DESCRIPTION PI N NO. DESCRIPTION1. Red 9. NC2. Green 10. Ground3. Blue 11. Ground4. Ground 12. DDC-Serial Data5. Ground 13. H-Sync6. R-Ground 14. V-Sync / *V-Clk7. G-Ground 15. DDC-Serial Clock8. B-Ground *For DDCFACTORY PRESET TIMING TABLECONNECTOR PIN ASSIGNMENT

Navigation menu