Top Victory Electronics CM769D 17" Color Monitor User Manual

Top Victory Electronics (Taiwan) Co Ltd 17" Color Monitor

User Manual

Note : The Audio port is not available till now. Top Victory doesn’t provide this port beforeSubmitted to FCC.Your Work Never Looked Better 7Elr/7ElrA7Elr+/7ElrA+USER MANUALTABLE OF CONTENTSFOR YOUR SAFETY -------------------------------------------------- 1SAFETY PRECAUTIONS -------------------------------------- 2BEFORE YOU OPERATE THE MONITOR ----------------------3FEATURES -------------------------------------------------------- 3PACKING LIST --------------------------------------------------- 3INSTALLATION INSTRUCTIONS --------------------------- 3CONTROLS AND CONNECTORS -------------------------- 4OPERATING INSTRUCTIONS ------------------------------------- 5GENERAL INSTRUCTIONS ---------------------------------- 5HOW TO ADJUST A SETTING ------------------------------ 6ADJUSTING THE PICTURE ---------------------------------- 7POWER MANAGEMENT FEATURE ----------------------- 7PLUG AND PLAY ------------------------------------------------ 9TECHNICAL SUPPORT(FAQ) -------------------------------------10APPENDIX ---------------------------------------------------------------11SPECIFICATIONS ------------------------------------------FACTORY PRESET TIMING TABLE -----------------------13CONNECTOR PIN ASSIGNMENT ------------------------- 13LIMITED THREE-YEAR WARRANTY -----------------------14-15Thank you very much for choosing the AOC Color Monitor.We recommend that you take a few minutes to read carefully through this brief butENGLISHDEUTSCHFRANÇAISESPAÑOLITALIANO11-12
1Before operating the monitor please read this manual thoroughly. This manualshould be retained for future reference.FCC Class B Radio Frequency Interference StatementWARNING: (FOR FCC CERTIFIED MODELS)NOTE: This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiateradio frequency energy, and if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one ormore of the following measures:1. Reorient or relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.4. Consult the dealer or an experienced radio/TV technician for help. NOTICE :1. The changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate theequipment.2. Shielded interface cables and AC power cord, if any, must be used inorder to comply with the emission limits.3. The manufacturer is not responsible for any radio or TV interferencecaused by unauthorized modification to this equipment. It is theresponsibilities of the user to correct such interference.As an ENERGY STAR Partner AOC International has determined that thisproduct meets the ENERGY STAR guidelines for energy efficiency. WARNING :To prevent fire or shock hazard, do not expose the monitor to rain or moisture.Dangerously high voltages are present inside the monitor. Do not open thecabinet. Refer servicing to qualified personnel only.Plug & Play Drivers for the AOC Spectrum Series Monitors are availableat AOC’s Web Site: www.aoc-europe.com
2!Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchensink, laundry tub, swimming pool or in a wet basement.!Do not place the monitor on an unstable cart, stand, or table. If the monitorfalls, it can injure a person and cause serious damage to the appliance.Use only a cart or stand recommended by the manufacturer or sold withthe monitor. If you mount the monitor on a wall or shelf, use a mounting kitapproved by the manufacturer and follow the kit instructions.!Slots and openings in the back and bottom of the cabinet are provided forventilation. To ensure reliable operation of the monitor and to protect itfrom overheating, be sure these openings are not blocked or covered. Donot place the monitor on a bed, sofa, rug, or similar surface. Do not placethe monitor near or over a radiator or heat register. Do not place themonitor in a bookcase or cabinet unless proper ventilation is provided.!The monitor should be operated only from the type of power sourceindicated on the label. If you are not sure of the type of power supplied toyour home, consult your dealer or local power company.!The monitor is equipped with a three-pronged grounded plug, a plug with athird (grounding) pin. This plug will fit only into a grounded power outlet asa safety feature. If your outlet does not accommodate the three-wire plug,have an electrician install the correct outlet, or use an adapter to groundthe appliance safely. Do not defeat the safety purpose of the groundedplug.!Unplug the unit during a lightning storm or when it will not be used for longperiods of time. This will protect the monitor from damage due to powersurges.!Do not overload power strips and extension cords. Overloading can resultin fire or electric shock.!Never push any object into the slot on the monitor cabinet. It could shortcircuit parts causing a fire or electric shock. Never spill liquids on themonitor.!Do not attempt to service the monitor yourself; opening or removing coverscan expose you to dangerous voltages and other hazards. Please refer allservicing to qualified service personnel.!To ensure satisfactory operation, use the monitor only with UL listedcomputers which have appropriate configured receptacles markedbetween 100 - 240V AC, Min. 1.5A.PRECAUTIONS
3BEFORE YOU OPERATE THE MONITOR•43.2cm(17”) Color Monitor•Crisp, Clear Display for Windows•Supports Resolutions up to 1280 ✕ 1024•Power Management•Ergonomic Design (MPR II Approved for 7Elr+/7ElrA+)•Space Saving, Compact Case DesignThe product package should include the following items:1. Monitor2. Owner's Manual3. Power Cord ( Refer to the "Using the right power cord" statement )4. Swivel Base5. Audio Cable ( For 7ElrA/7ElrA+ only ) SWIVEL BASETo attach the swivel base to the monitor, do the following:•Carefully turn the monitor on its side or upside down. ( see figure 1 )•Locate the cavities at the bottom front of the monitor.•Insert the pegs on the swivel base into these cavities. Push the swivelbase forward until the swivel base locks in place.•To remove the swivel base, hold the bottom of the swivel base, then pushit out.Figure 1 Installing and Removing the Swivel BaseFEATURESCHECKING THE CONTENTS OF THE MONITOR PACKAGEINSTALLATION INSTRUCTIONS
4 POWER CORDPower Source:1. Make sure the power cord is the correct type that required in your area.2. This monitor has a universal power supply that allows operation in either100/120V AC or 220/240V AC voltage area ( No user adjustment isrequired. )3. Connect the power cord into your monitor’s power input socket, and thenplug the other end into a 3-pin AC power outlet. The power cord may beconnected to either a wall power outlet or the power outlet socket on yourPC, depending on the type of power cord supplied with your monitor. VIDEO CABLEConnecting the Video Cable: the monitor comes with a built-in video cable.Plug the signal cable′s 15-pin connector into the computer's video port andtighten the two screws on the cable connector. (see figure 2)Caution:Don’t bend the signal cable, otherwise it will break the innerwire.Connecting the Power Cord: Plug the power cord into the monitor's ACpower jack. Then plug the power cord into a grounded AC outlet, UL-approved power strip, or the power output socket on your PC.Caution: If the AC outlet is not grounded, install the proper groundingadapter (not supplied).Connecting the Earphone Cable ( 7ElrA/7ElrA+ only ): Plug earphonecable into earphone output jack.Connecting the Audio Cable (7ElrA/7ElrA+ only ): Plug one end of theaudio cable into the computer’s multi-media (or sound) card′s audio output andthe other end into the monitor's audio input.321Figure 2 Connecting Cables1. AC InletCONTROLS AND CONNECTORS
52. Earphone (7ElrA/7ElrA+ only)3. Audio In (7ElrA/7ElrA+ only)
6OPERATING INSTRUCTIONSThe power switch is located at front panel of the monitor. Press the powerswitch to turn the monitor on or off. The other control knobs are located at thebase of the monitor (See Figure 3). By changing these settings, the picturecan be adjusted to your personal preferences.•The power cord should be connected.•Connect the video cable from the monitor to the video card.•To turn the monitor on, press the POWER switch to ON position. Thepower indicator will light up.•Your monitor features a unique quick switch system which provides apicture within seconds after the monitor is switched on.67891011121312345Figure 3 External Control Knob EXTERNAL CONTROLSSwitch: Functions:1. Power On/Off Switch 6. Contrast 11. V-Center2. LED 7. Brightness 12. Pincushion3. Up Key 8. H-Size 13. Trapezoid4. Down Key 9. H-Center5. Function Key 10. V-SizeGENERAL INSTRUCTIONS
7 NOTES•Do not install the monitor in a location near heat sources such as radiatorsor air ducts , or in a place subject to direct sunlight , or excessive dust ormechanical vibration or shock.•Save the original shipping carton and packing materials, as they will comein handy if you ever have to ship your monitor.•For maximum protection, repackage your monitor as it was originallypacked at the factory.•To keep the monitor looking new, periodically clean it with a soft cloth.Stubborn stains may be removed with a cloth lightly dampened with a milddetergent solution. Never use strong solvents such as thinner, benzene, orabrasive cleaners, since these will damage the cabinet. As a safetyprecaution, always unplug the monitor before cleaning it.1. Press the knob, the green LED lights and the power is ON.Press this knob again, the green LED disappears and the power is OFF.2. When press the “FUNC” key, the LED will flash to indicate the function hasbeen selected.3. When function has been selected, press or to adjust picture image.4. Press the Up or Down key to get the optimal volume for the multimediamodel only. The most left LED will flash to indicate the adjustable levelshave reached to the maximum or minimum.5. If you press the Func. & Down keys simultaneously it functions as an audiomute, and press Up or Down key to release audio function for multimediamodel only.6. Press the “FUNC” key until the LEDs of pincushion and trapezoid flashsimultaneously, then press Up or Down key to adjust the picture tilt tohorizontal position.HOW TO ADJUST A SETTING
8The description for function control LEDS1. CONTRAST Adjust the picture contrast.2. BRIGHTNESS Adjust the picture brightness.3. H-SIZE Adjust the picture’s horizontal size.4. H-CENTER Adjust the horizontal position of the picture.5. V-SIZE Adjust the picture’s vertical size.6. V-CENTER Adjust the vertical position of the picture.7. PINCUSHION Adjust the pincushion and barrel.8. TRAPEZOID Adjust the picture’s trapezoid distortion.9. +RECALL To recall original factory preset mode.10. +ROTATION Adjust the picture’s tilt to horizontal position.The power management feature of this product complies with every powersaving requirements of ENERGY STAR and VESA DPMS when activated, itautomatically reduces unnecessary power consumption of the monitor whenyour computer is not in use.To use the feature, the monitor needs to be connected to a VESA DPMScomputer. There are three power management modes available, these aredescribed below. The required settings, including the timer setting, should bemade by the computer.••••Stand-by ModeWhen the H-sync signal from the computer is off, the monitor enters intoStand-by Mode which reduces the power consumption to less than 15W.The screen becomes dark, and the power indicator turns to orange. FromStand-by Mode, the screen reappears instantaneously when the keyboardor the mouse is touched again.ADJUSTING THE PICTUREPOWER MANAGEMENT FEATURE
9••••Suspend ModeWhen the V-sync signal from the computer is off, the monitor enters intoSuspend Mode which reduces the power consumption to less than 15W.The screen becomes dark, and the power indicator turns to orange. FromSuspend Mode, the screen reappears instantaneously when the keyboardor the mouse is touched again.••••Active-off ModeWhen both the H and V sync signals form the computer are off, the monitorenters into Active-off Mode which reduces the power consumption to lessthan 8W. The screen becomes dark, and the power indicator turns toorange. From Active-off Mode, the screen reappears instantaneously whenthe keyboard or the mouse is touched again.•The power-saving mode can be indicated by the light-emitting diode (LED)on the front panel:Signal PowerMode Cable H-Sync V-Sync Video Indicator ConsumptionOn* Attached Yes Yes Active Green ≤ 120 WStand-by Attached No Yes Blank Orange ≤ 15 WSuspend Attached Yes No Blank Orange ≤ 15 WOff Attached No No Blank Orange ≤ 8 W FEATURESGreen monitor•The monitor has a power saving function that conforms to the VESA DPMSstandard. This feature will only work if your PC is a green PC. This featureis similar to a screen saver, except that your monitor will turn it off insteadof activating the screen saver.To activate this feature in Windows® 98 :In Windows® 98, this feature can be activated and customized under thescreen saver setting of the display properties.1. Right click on the desktop and choose Properties.2. Click on the tab that says Screen Saver. If your system supports GreenPC, there will be a section entitled “Energy Saving Features of Monitor.” Ifthere isn’t a section like that, then your PC does not support GreenMonitor. The monitor will behave just like a normal monitor, so you willhave to turn it off manually to save energy.3. In the “Energy Saving Features of Monitor” sections are two boxes,Standby and Shut off. To activate either one, click the box next to eachone.4. You can specify the amount of inactive time before your monitor entersstandby mode or shuts off.
10Plug & Play DDC1/2B FeatureThis monitor is equipped with VESA DDC1/2B capabilities according to theVESA DDC STANDARD. It allows the monitor to inform the host system of itsidentity and, depending on the level of DDC used, communicate additionalinformation about its display capabilities. The communication channel isdefined in two levels, DDC1 and DDC2B.The DDC1 is a unidirectional data channel from the display to the host thatcontinuously transmits EDID information. The DDC2B is a bidirectional datachannel based on the I²C protocol. The host can request EDID informationover the DDC2B channel.THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE ISNO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATEPROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.This monitor meets the Power Management standards as set by the VideoElectronics Standards Association (VESA) and/or the United StatesEnvironmental Protection Agency (EPA) and The Swedish ConfederationEmployees ( NUTEK ). This feature is designed to conserve electrical energyby reducing power consumption when there is no video input signal present.When there is no video input signal this monitor, following a time-out period,will automatically switch to an OFF mode. This reduces the monitor's internalpower supply consumption. After the video input signal is restored, full poweris restored and the display is automatically redrawn. The appearance is similarto a "Screen Saver" feature except the display is completely off. The display isrestored by pressing a key on the keyboard, or clicking the mouse. USING THE RIGHT POWER CORD :The accessory power cord for the Northern American region is the wallet plugwith NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating forthe power cord shall be 125 volts AC.Supplied with units intended for connection to power outlet of personalcomputer: Please use a cord set consisting of a minimum No. 18 AWG, typeSJT or SVT three conductors flexible cord. One end terminates with agrounding type attachment plug, rated 10A, 250V, CEE-22 male configuration.The other end terminates with a molded-on type connector body, rated 10A,250V, having standard CEE-22 female configuration.PLUG AND PLAY
11
12TECHNICAL SUPPORT (FAQ)Problem & Question Possible SolutionPower LED is not on *Check if the Power Switch is in the ONposition*Power Cord should be connectedNo Plug & Play *Check if the PC system is Plug & Playcompatible*Check if the Video Card is Plug & Playcompatible*Check if the D-15 plug pin of Video Cableis bent*Make sure the AOC Monitor Drivers areinstalled(AOC Monitor Drivers are available at:www.aoc-europe.com)No picture *Computer Power Switch should be in theON position*Computer Video Card should be snuglyseated in its slot*The Signal Cable should be completelyconnected to the computer*Check the color of the Power LEDindicator. If it is orange, then the monitorand the PC system are in power-savingmode. You need press your keyboard ormove the mouse to reactivate the system.Picture is fuzzy *Adjust the Contrast and BrightnessControls.Picture bounces or a wavepattern is present in the picture *Move electrical devices that may causeelectrical interference.Monitor is stuck in “PowerSaving Mode” *Make sure monitor’s video cable isproperly connected to the computer.*Inspect monitor’s video cable and makesure none of the pins are bent.*Make sure computer is operational byhitting the CAPS LOCK key on thekeyboard while observing the CAPSLOCK LED. The LED should either turnON or OFF after hitting the CAPS LOCKkey.Missing one of the primarycolors (RED, GREEN, orBLUE)*Inspect the monitor’s video cable andmake sure that none of the pins are bent.
13APPENDIX SPECIFICATIONSCRT Size 43.2cm(17"), 90º deflection, 27mmneck,CRT Viewable ImageSize 40.6cm (16"), diagonalType 0.28mm dot pitch.Video 0.7Vpp, R,G,B AnalogInput Separate Sync. TTL LevelH./V.- Sync. Positive / NegativeScanning H-Frequency 30kHz - 69kHzFrequency V-Frequency 50Hz-160HzMax. Resolution 1280 x 1024Video Bandwidth 110MHzFactory Preset mode : 6User Programmable mode : 10Power Source Universal AC 100 - 240V,50Hz / 60HzOperating 0ºC to 40ºC ambientHumidity 10%to 85%relative, non-condensingDimensions7Elr/7Elr+: Monitor & Base 410(W) × 411(H) × 430(D)mm7ElrA/7ElrA+: Monitor & Base 410(W) × 448(H) × 430(D)mmWeight7Elr/7Elr+: Unit (net) 16.0kgs ( Net )7ElrA/7ElrA+: Unit (net) 16.8kgs ( Net )Signal Cable: Attached Mini D-sub 15 Male430(in mm)7Elr/7Elr+
14Switch •Power On/Off switch•Up/Down Key•Function KeyExternal Controls: Functions •Contrast•Brightness•H-Size•H-Center•V-Size•V-Center•Pincushion•Trapezoid•Rotation (for 7ElrA/7ElrA+ only)Plug & Play DDC1/2BPower Management EPA, VESA DPMSPower Consumption ( Maximum ) 120 WattsPre-set Display Area 300mm x 230mmAudio Output (for 7ElrA /7ElrA+ only) Rated Power 1W rms(Per channel)Regulatory Compliance UL, CSA, FDA, FCC, TÜV/GS, CE,MPR IITCO’99( for 7Elr+/7ElrA+ only )360 385364(ln mm)
15STANDARD RESOLUTION HORIZONTALFREQUENCY VERTICALFREQUENCYIBM 720 x 400 31.5kHz 70HzVGA 640 x 480 31.5kHz 60HzVESA/85 640 x 480 43.2kHz 85HzVESA/85 800 x 600 53.6kHz 85HzVESA/85 1024 x 768 68.7kHz 85HzVESA/60 1280 x 1024 64.0kHz 60Hz1561011 1515 - Pin Color Display Signal CablePIN NO. DESCRIPTION PIN NO. DESCRIPTION1. Red 9. NC2. Green 10. Ground3. Blue 11. Monitor Ground4. Ground 12. DDC-Serial Data5. Ground 13. H-Sync6. R-Ground 14. V-Sync / *V-Clk7. G-Ground 15. DDC-Serial Clock8. B-Ground ✲For DDCFACTORY PRESET TIMING TABLECONNECTOR PIN ASSIGNMENT
16LIMITED THREE-YEAR WARRANTY*forAOC Spectrum Color Monitors sold within EuropeAOC International (Europe) GmbH warrants this product to be free fromdefects in material and workmanship for a period of Three (3) years after theoriginal date of consumer purchase. During this period, AOC International(Europe) GmbH will, at its option, either repair the defective product with newor rebuilt parts, or replace it with a new or rebuilt product at no charge exceptas *stated below. The defective products that are replaced become theproperty of AOC International (Europe) GmbH.If the product appears to be defective, please contact your local dealer orrefer to the warranty card when attached to the product.Deliver the product freight pre-paid, along with the dated proof of purchase, tothe AOC Authorized Service Center. If you cannot deliver the product inperson:• Pack it in its original shipping container (or equivalent)• Put the RMA number on the address label• Put the RMA number on the shipping carton• Insure it (or assume the risk of loss/damage during shipment)• Pay all shipping charges AOC International (Europe) GmbH is responsible neither for any damage orloss during inbound transport damage nor to inbound product that was notproperly packaged. AOC International (Europe) GmbH will pay the return shipping charges withinone of the countries specified within this warranty statement. AOC International (Europe) GmbH is not responsible for any costs associatedwith the transportation of product across international borders. This includesthe international border within the European Union. * This limited warranty does not cover any losses or damages that occur as aresult of• Shipping or improper installation or maintenance• Misuse• Neglect• Any cause other than ordinary commercial or industrial application• Adjustment by non-authorized source• Repair, modification, or installation of options or parts by anyoneother than an AOC Authorized Service Center• Improper environment• Excessive or inadequate heating or air conditioning or electricalpowers failures, surges, or other irregularities
17This limited warranty does not cover any of the product firmware or hardwarethat you or any third party have modified or altered; you bear the soleresponsibility and liability for any such modification or alteration.ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT(INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESSFOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO APERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THEORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHEREXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD.AOC INTERNATIONAL (EUROPE) GMBH OBLIGATIONS AND YOURREMEDIES HEREUNDER ARE SOLELY AND EXCULSIVELY AS STATEDHERE. AOC INTERNATIONAL (EUROPE) GMBH LIABILITY, WHETHERBASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OROTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUALUNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NOEVENT SHALL AOC INTERNATIONAL (EUROPE) GMBH BE LIABLE FORANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT,OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE.SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OFINCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVELIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITEDWARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVEOTHER RIGHTS, WHICH MAY VARY FROM COUNTRY TO COUNTRY.THIS LIMITED WARRANTY IS ONLY VALID FOR PRODUCTS PURCHASEDIN THE MEMBER COUNTRIES OF THE EUROPEAN UNION.

Navigation menu