TheBIT AP6212 WI-FI/BT SIP MODULE User Manual WMDM 110G

TheBIT co.,Ltd WI-FI/BT SIP MODULE WMDM 110G

User Manual

正基科技股份有限公司 SPECIFICATION SPEC. NO.： REV： 1.1 DATE： 09. 02.2014PRODUCT NAME： AP6212 APPROVED CHECKED PREPARED DCC ISSUE NAME
AP6212 WiFi+Bluetooth+FM RX SIP Module Spec Sheet
1 Revision History Date Revision Content Revised By Version 2014/04/08 - PreliminaryBrian 1.0 2014/09/02 - Pin Definition ModifiedBrian 1.1
AP6212 Datasheet2 Contents Contents ................................................................................................................... 2 1. Introduction ......................................................................................................... 3 2. Features............................................................................................................... 43. Deliverables ........................................................................................................ 5 3.1 Deliverables .................................................................................................... 5 3.2 Regulatory certifications ................................................................................. 5 4. General Specification ......................................................................................... 6 4.1 General Specification ...................................................................................... 6 4.2 Voltages .......................................................................................................... 6 4.2.1 Absolute Maximum Ratings .................................................................... 6 4.2.2 Recommended Operating Rating ........................................................... 6 5. WiFi RF Specification ......................................................................................... 7 5.1 2.4GHz RF Specification................................................................................. 7 6. Bluetooth Specification ...................................................................................... 9 6.1 Bluetooth Specification ................................................................................... 9 7. FM Specification ............................................................................................... 10 7.1 FM Specification (TBD) ................................................................................. 10 8. Pin Assignments ............................................................................................... 11 8.1 Pin Outline .................................................................................................... 11 8.2 Pin Definition ................................................................................................ 11 9. Dimensions ....................................................................................................... 13 9.1 Physical Dimensions .................................................................................... 13 9.2 Layout Recommendation .............................................................................. 14 10. External clock reference .................................................................................. 15 10.1 SDIO Pin Description .................................................................................. 15 11. Host Interface Timing Diagramo ..................................................................... 16 11.1 Power-up Sequence Timing Diagram ......................................................... 16 11.2 SDIO Default Mode Timing Diagram ........................................................... 18 11.3 SDIO High Speed Mode Timing Diagram .................................................... 19 12. Recommended Reflow Profile ......................................................................... 20 13. Package Information ........................................................................................ 21 13.1Label .......................................................................................................... 21 13.2 Dimension ................................................................................................. 22 13.3 MSL Level / Storage Condition ................................................................... 24
AP6212 Datasheet3 1. IntroductionTechnology would like to announce a low-cost and low-power consumption module which has all of the WiFi, Bluetooth and FM functionalities. The highly integrated module makes the possibilities of web browsing, VoIP, Bluetooth headsets, FM radio functional applications and other applications. With seamless roaming capabilities and advanced security, also could interact with different vendors’ 802.11b/g/n Access Points in the wireless LAN. The wireless module complies with IEEE 802.11 b/g/n standard and it can achieve up to a speed of 72.2Mbps with single stream in 802.11n draft, 54Mbps as specified in IEEE 802.11g, or 11Mbps for IEEE 802.11b to connect to the wireless LAN. The integrated module provides SDIO interface for WiFi, UART / I2S / PCM interface for Bluetooth and UART / I2S / PCM interface for FM. This compact module is a total solution for a combination of WiFi + BT + FM technologies. The module is specifically developed for Smart phones and Portable devices.
AP6212 Datasheet4 2. Features802.11b/g/n single-band radioBluetooth V4.0(HS) with integrated Class 1.5 PA Concurrent Bluetooth, FM (RX) RDS/RBDS, and WLAN operationSimultaneous BT/WLAN receive with single antennaWLAN host interface options:- SDIO v2.0 — up to 50 MHz clock rateBT host digital interface:- UART (up to 4 Mbps)FM multiple audio routing options: I2S, PCM, eSCO, A2DPIEEE Co-existence technologies are integrated die solutionECI — enhanced coexistence support, ability to coordinate BT SCO transmissionsaround WLAN receivesA simplified block diagram of the module is depicted in the figure below.
AP6212 Datasheet5 3. Deliverables3.1 Deliverables The following products and software will be part of the product. Module with packagingEvaluation KitsSoftware utility for integration, performance test.Product Datasheet.Agency certified pre-tested report with the adapter board.3.2 Regulatory certifications The product delivery is a pre-tested module, without the module level certification. For module approval, the platform’s antennas are required for the certification.
AP6212 Datasheet6 4. General Specification4.1 General Specification 4.2 Voltages 4.2.1 Absolute Maximum Ratings Symbol Description Min. Max. Unit VBAT Input supply Voltage -0.55.5 V WL_VIO_SD Digital/Bluetooth/SDIO/ I/O Voltage -0.53.6 V 4.2.2 Recommended Operating Rating The module requires two power supplies: VBAT and VDDIO. Min. Typ. Max. Unit Operating Temperature -3025 85 deg.CVBAT 3.0 3.74.8 V VDDIO 1.7 3.3 3.6 V Model Name AP6212 Product Description Support WiFi/Bluetooth/FM functionalities Dimension L x W x H: 12 x 12 x 1.5 (typical) mm WiFi Interface SDIOV2.0 BT Interface UART / PCM FM Interface UART / PCM / Audio Operating temperature -30°C to 85°CStorage temperature -40°C to 85°CHumidity Operating Humidity 10% to 95% Non-Condensing Storage Humidity 5% to 95% Non-Condensing
AP6212 Datasheet7 5. WiFi RF Specification5.1 2.4GHz RF Specification Conditions : VBAT=3.7V ; VDDIO=3.3V ; Temp:25°CFeature Description WLAN Standard IEEE 802.11b/g/n, WiFi compliant Frequency Range 2.400 GHz ~ 2.4835 GHz (2.4 GHz ISM Band)Number of Channels 2.4GHz：Ch1 ~ Ch11Modulation 802.11b : DQPSK, DBPSK, CCK 802.11 g/n : OFDM /64-QAM,16-QAM, QPSK, BPSK Output Power(Burst Average Power)802.11b /11Mbps : 7.5 dBm ± 1 dB @ EVM  -9dB802.11g /54Mbps : 7.5 dBm ± 1 dB @ EVM  -25dB802.11n /65Mbps : 7.5 dBm ± 1 dB @ EVM  -28dBReceive Sensitivity (11n,20MHz) @10% PER - MCS=0 PER @ -85 dBm, typical - MCS=1 PER @ -84 dBm, typical - MCS=2 PER @ -82 dBm, typical - MCS=3 PER @ -80 dBm, typical - MCS=4 PER @ -77 dBm, typical - MCS=5 PER @ -73 dBm, typical - MCS=6 PER @ -71 dBm, typical - MCS=7 PER @ -68 dBm, typical Receive Sensitivity (11g) @10% PER - 6Mbps PER @ -86 dBm, typical - 9Mbps PER @ -85 dBm, typical - 12Mbps PER @ -85 dBm, typical - 18Mbps PER @ -83 dBm, typical - 24Mbps PER @ -81 dBm, typical - 36Mbps PER @ -78 dBm, typical - 48Mbps PER @ -73 dBm, typical - 54Mbps PER @ -71 dBm, typical Receive Sensitivity (11b) @8% PER - 1Mbps PER @ -90 dBm, typical - 2Mbps PER @ -88 dBm, typical - 5.5Mbps PER @ -87 dBm, typical - 11Mbps PER @ -84 dBm, typical Data Rate 802.11b : 1, 2, 5.5, 11Mbps 802.11g : 6, 9, 12, 18, 24, 36, 48, 54Mbps
AP6212 Datasheet8 Data Rate (20MHz ,Long GI,800ns) 802.11n: 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps Data Rate (20MHz ,short GI,400ns) 802.11n : 7.2, 14.4, 21.7, 28.9, 43.3, 57.8, 65,72.2Mbps Maximum Input Level 802.11b : -10 dBm 802.11g/n : -20 dBm Antenna Reference Small antennas with 3.691 dBi peak gain
AP6212 Datasheet9 6. Bluetooth Specification6.1 Bluetooth Specification Conditions : VBAT=3.7V ; VDDIO=3.3V ; Temp:25°CFeature Description General Specification Bluetooth Standard Bluetooth of 1, 2 and 3 Mbps. Host Interface UART Antenna Reference Small antennas with 3.691 dBi peak gainFrequency Band 2402MHz ~ 2480MHz Number of Channels 79 channels Modulation FHSS, GFSK, DPSK, DQPSK RF Specification Min. Typical. Max. Output Power (Flame Average Power) BDR : 7.5 ± 1 dB EDR : 3.5 ± 1 dBSensitivity @ BER=0.1% for GFSK (1Mbps) -86 dBmSensitivity @ BER=0.01% for π/4-DQPSK (2Mbps) -86 dBmSensitivity @ BER=0.01% for 8DPSK (3Mbps) -80 dBmMaximum Input Level GFSK (1Mbps):-20dBm π/4-DQPSK (2Mbps) :-20dBm 8DPSK (3Mbps) :-20dBm
AP6212 Datasheet10 7. FM Specification7.1 FM Specification (TBD) Conditions : VBAT=3.7V ; VDDIO=3.3V ; Temp:25°CFeature Description General Specification Frequency Band 76MHz-108MHz Host Interface HCI UART, I2S/PCM Channel step 50 KHz Analog Audio output load RL>30KΩ, CL>20pF Characteristics Condition MIN TYP MAX UNIT Transmitter (FM Tx load = 120nH, Q>30)Output Power Level dBuV Audio harmonic distortion (fmod=1KHz, △f=75KHz,Pilot △f=6.75KHz) % Audio SNR (△f=22.5KHz, I2Saudio in SNR ≧57dB ) MONO dB Stereo Receiver (FM Tx Antenna = 120nH, Q>30) RDS Sensitivity dBm Audio harmonic distortion (Vin=1mV, △f=75KHz) fmod=1KHz % fmod=3KHz Maximum SNR (fmod=1KHz,△f=22.5KHz, BW=300Hz to 15KHz) MONO dB Stereo RF input power level dBuV
AP6212 Datasheet11 8. Pin Assignments8.1 Pin Outline < TOP VIEW > 8.2 Pin Definition NO Name Type Description 1 GND － Ground connections 2 WL_BT_ANT I/O RF I/O port 3 GND － Ground connections 4 FM_RX I FM radio RF input antenna port 5 NC － Floating (Don’t connected to ground) 6 BT_WAKE I HOST wake-up Bluetooth device 7 BT_HOST_WAKE O Bluetooth device to wake-up HOST 8 NC － Floating (Don’t connected to ground) 9 VBAT P Main power voltage source input 10 XTAL_IN I Crystal input 11 XTAL_OUT O Crystal output 12 WL_REG_ON I Internal regulators power enable/disable 13 WL_HOST_WAKE O WLAN to wake-up HOST
AP6212 Datasheet12 14 SDIO_DATA_2 I/O SDIO data line 2 15 SDIO_DATA_3 I/O SDIO data line 3 16 SDIO_DATA_CMD I/O SDIO command line 17 SDIO_DATA_CLK I/O SDIO clock line 18 SDIO_DATA_0 I/O SDIO data line 0 19 SDIO_DATA_1 I/O SDIO data line 1 20 GND － Ground connections 21 VIN_LDO_OUT P Internal Buck voltage generation pin 22 VDDIO P I/O Voltage supply input 23 VIN_LDO P Internal Buck voltage generation pin 24 LPO I External Low Power Clock input (32.768KHz) 25 PCM_OUT O PCM Data output 26 PCM_CLK I/O PCM clock 27 PCM_IN I PCM data input 28 PCM_SYNC I/O PCM sync signal 29 NC － Floating (Don’t connected to ground) 30 NC － Floating (Don’t connected to ground) 31 GND － Ground connections 32 NC － Floating (Don’t connected to ground) 33 GND － Ground connections 34 BT_RST_N I Low asserting reset for Bluetooth core 35 NC － Floating (Don’t connected to ground) 36 GND － Ground connections 37 GPIO4 I/O WiFi Co-existence pin with LTE 38 GPIO3 I/O WiFi Co-existence pin with LTE 39 GPIO2 I/O WiFi Co-existence pin with LTE 40 GPIO1 I/O WiFi Co-existence pin with LTE 41 UART_RTS_N O Bluetooth/FM UART interface 42 UART_TXD O Bluetooth/FM UART interface 43 UART_RXD I Bluetooth/FM UART interface 44 UART_CTS_N I Bluetooth/FM UART interface 45 TP1 O FM Analog AUDIO left output 46 TP2 O FM Analog AUDIO right output 47 TP3 (NC) － Floating (Don’t connected to ground)
AP6212 Datasheet13 9. Dimensions9.1 Physical Dimensions (Unit: mm) < TOP VIEW > < Side View > < TOP VIEW >
AP6212 Datasheet14 9.2 Layout Recommendation (Unit: mm) < TOP VIEW >
AP6212 Datasheet15 10. External clock referenceExternal LPO signal characteristics Parameter Specification Units Nominal input frequency 32.768 kHz Frequency accuracy 30ppm Duty cycle 30 - 70 % Input signal amplitude 400 to 1800mV, p-p Signal type Square-wave - Input impedance >100k<5 pF Clock jitter (integrated over 300Hz – 15KHz) <1 Hz Output high voltage 0.7Vio - Vio V External Ref_CLK signal characteristics 10.1 SDIO Pin Description The module supports SDIO version 2.0 for 4-bit modes (100 Mbps), and high speed 4-bit (50 MHz clocks – 200 Mbps). It has the ability to stop the SDIO clock and map the interrupt signal into a GPIO pin. This ‘out-of-band’ interrupt signal notifies the host when the WLAN device wants to turn on the SDIO interface. The ability to force the control of the gated clocks from within the WLAN chip is also provided.
AP6212 Datasheet16 Function 0 Standard SDIO function (Max BlockSize / ByteCount = 32B)Function 1 Backplane Function to access the internal System On Chip (SOC)address space (Max BlockSize / ByteCount = 64B)Function 2 WLAN Function for efficient WLAN packet transfer through DMA (MaxBlockSize/ByteCount=512B)SDIO Pin Description SD 4-Bit Mode DATA0 Data Line 0 DATA1 Data Line 1 or Interrupt DATA2 Data Line 2 or Read Wait DATA3 Data Line 3 CLK Clock CMD Command Line 11. Host Interface Timing Diagram11.1 Power-up Sequence Timing Diagram The module has signals that allow the host to control power consumption by enabling or disabling the Bluetooth, WLAN and internal regulator blocks. These signals are described below. Additionally, diagrams are provided to indicate proper sequencing of the signals for carious operating states. The timing value indicated are minimum required values: longer delays are also acceptable. ※WL_REG_ON: Used by the PMU to power up the WLAN section. When this pin ishigh, the regulators are enabled and the WLAN section is out of reset. When thispin is low the WLAN section is in reset.※BT_RST_N: Low asserting reset for Bluetooth and FM only. This pin has no effecton WLAN and does not control any PMU functions. This pin must be driven high orlow (not left floating).
AP6212 Datasheet17 WLAN=ON, Bluetooth=ON WLAN=OFF, Bluetooth=OFF WLAN=ON, Bluetooth=OFF
AP6212 Datasheet18 WLAN=OFF, Bluetooth=ON 11.2 SDIO Default Mode Timing Diagram
AP6212 Datasheet19 11.3 SDIO High Speed Mode Timing Diagram
AP6212 Datasheet20 12. Recommended Reflow ProfileReferred to IPC/JEDEC standard. Peak Temperature : <250°C Number of Times : 2 times 2.5℃/sec 2.5°C/sec40~70 sec 250℃
AP6212 Datasheet21 13. Package Information13.1Label Label A Anti-static and humidity notice Label B MSL caution / Storage Condition Label C Inner box label . Label D Carton box label .
AP6212 Datasheet22 13.2 Dimension
AP6212 Datasheet23 AB C Humidity indicator Desiccant C D
AP6212 Datasheet24 13.3 MSL Level / Storage Condition ※NOTE : Accumulated baking time should not exceed 96hrs
Regulatory Notices1. FCCFCC Part 15.19 Statements:This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation.FCC Part 15.21 statementAny changes or modifications not expressly approved by the party responsible for compliance couldvoid the user's authority to operate this equipment.FCC Part 15.105 statement This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may cause harmful interference toradio communications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiveris connected.Consult the dealer or an experienced radio/TV technician for help.OEM Responsibilities to comply with FCC and Industry Canada RegulationsThe module has been certified for integration into products only by OEM integrators under thefollowing condition:- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). End Product Labeling The module is labeled with its own FCC ID. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:“Contains FCC ID: 2AI4I-AP6212

Navigation menu