Thales Defense and Security 4102023501 LAND MOBILE RADIO User Manual Liberty Users Guide

Thales Communications Inc LAND MOBILE RADIO Liberty Users Guide

Contents

Manual rev

LIBERTYTM LAND MOBILE RADIO PRC7332 USER’S GUIDE APRIL 2009
FRONT MATTER 2 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION ! NOTE LIBERTYTM RADIOS Please use the following field support contact information: Contact Info: Bob DiDonato, Thales Communications, Inc. Mobile: 1-410-908-7678 Email: Bob.DiDonato@thalescomminc.com Scott Glazer, Thales Communications, Inc. Mobile: 1-240-422-2612 Email: Scott.Glazer@thalescomminc.com
FRONT MATTER Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION iii COPYRIGHT: APRIL 2009 THALES COMMUNICATIONS, INC. PUBLISHED AND CONFIDENTIAL WORK ALL RIGHTS RESERVED CONFIGURATION NOTICE: This document contains technical information pertinent to the LibertyTM Radio. The information contained herein is for the support of the LibertyTM Radio. PROPRIETARY NOTICE: This document contains information proprietary to THALES COMMUNICATIONS, INC. It is furnished for operation and support purposes only and not for reprocurement. All reprocurement and manufacturing rights are expressly reserved by THALES COMMUNICATIONS, INC., and no such use may be made of this document, either directly or indirectly without the prior written consent of THALES COMMUNICATIONS, INC. LICENSE AGREEMENTS This software is licensed solely for use within this product. US Patent Nos. #6,912,495 B2, #6,199,037 B1, #5,870,405, #5,826,222, #5,754,974, #5,715,365, #5,701,390, #5,649,050, #5,630,050, #5,630,011, #5,581,656, #5,517,511, #5,491, 772, #5,247,579, #5,226,084, and #5,195,166. The AMBE ® voice compression software included in the product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this software is explicitly prohibited from attempting to decompile, reverse engineer, or disassemble the object code, or in any other way convert the object code into a human-readable form. ! NOTE This manual contains information that is current as of the date shown below. Additional functionality is being developed for the radio and the appearance of operating screens is subject to change from those shown herein. Thales Part 84382 Rev 2 April 2009
FRONT MATTER iv Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION RECORD OF CHANGES Revision Date Description of Change Author Rev 1 Jan 2009 Initial Pilot Field Trials Version SJA Rev 2 April 2009 Updated to include scan functions, use of pre-programmable side buttons, and added FCC information. SJA
FRONT MATTER Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION v TABLE OF CONTENTS CHAPTER .......................................................................................................................................... PAGE LICENSE AGREEMENTS ..................................................................................................................................... III LIST OF FIGURES ................................................................................................................................................. VII LIST OF TABLES ................................................................................................................................................. VIII RADIO FREQUENCY ENERGY SAFETY INFORMATION ........................................................................... IX ELECTROMAGNETIC INTERFERENCE COMPATIBILITY .......................................................................... X SAFETY SUMMARY .............................................................................................................................................. XI NOTATIONS USED IN THIS MANUAL ............................................................................................................. XII FOREWORD ......................................................................................................................................................... XIII CHAPTER 1 GETTING TO KNOW THE RADIO........................................................................................ 1-1 GENERAL INFORMATION........................................................................................................................................ 1-1 EQUIPMENT CHARACTERISTICS ............................................................................................................................. 1-2 TECHNICAL CHARACTERISTICS ............................................................................................................................. 1-3 LIBERTYTM RADIO – LOCATION OF CONTROLS AND INDICATORS .......................................................................... 1-4 CONTROLS AND INDICATORS ............................................................................................................................... 1-7 CONTROLS ............................................................................................................................................................. 1-7 Special “Hot Keys” .......................................................................................................................................... 1-8 Four-Way Navigation Buttons with Enter Button ............................................................................................ 1-9 Side-Buttons ................................................................................................................................................... 1-10 INDICATORS ......................................................................................................................................................... 1-11 LCD and Keypad Backlight ........................................................................................................................... 1-11 LED Indicators ............................................................................................................................................... 1-11 Connectors ..................................................................................................................................................... 1-12 CHAPTER 2 DISPLAY / MENU SCREENS .................................................................................................. 2-1 GENERAL INFORMATION .................................................................................................................................. 2-1 DISPLAY/ MENU SCREENS ................................................................................................................................ 2-2 SPLASH Screen ............................................................................................................................................... 2-2 HOME Screen .................................................................................................................................................. 2-3 MENU Screen Displays ................................................................................................................................... 2-6 SELECT Menu Screen ..................................................................................................................................... 2-7 VIEW Menu Screen ......................................................................................................................................... 2-8 PROGRAM Menu Screen ................................................................................................................................ 2-9 RADIO INFORMATION Menu Screen ........................................................................................................ 2-18 MAINTENANCE Menu Screen .................................................................................................................... 2-19 CHAPTER 3 OPERATING INSTRUCTIONS ............................................................................................... 3-1 GENERAL INFORMATION........................................................................................................................................ 3-1 OPERATING INSTRUCTIONS .............................................................................................................................. 3-1 Connecting the Battery ..................................................................................................................................... 3-1 Connecting the Antenna ................................................................................................................................... 3-1 Radio Programming ......................................................................................................................................... 3-1 Turning on the Radio ....................................................................................................................................... 3-2 Menu Access .................................................................................................................................................... 3-3 Transmitting ..................................................................................................................................................... 3-4
FRONT MATTER vi Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Receiving ......................................................................................................................................................... 3-4 P25 Unit to Unit Call ....................................................................................................................................... 3-5 Scanning – Conventional and Priority ............................................................................................................. 3-6 Using the Pre-Programmed Side Buttons ......................................................................................................... 3-8 Modifying Menu Selections – SELECT Menu or PROGRAM Menu ............................................................. 3-9 Changing ZONES ............................................................................................................................................ 3-9 Screensaver .................................................................................................................................................... 3-10 CHAPTER 4 MAINTENANCE ........................................................................................................................ 4-1 GENERAL INFORMATION ........................................................................................................................................ 4-1 OPERATIONAL CHECKOUT ..................................................................................................................................... 4-2 RADIO PREVENTIVE MAINTENANCE ...................................................................................................................... 4-2 Inspection and Cleaning ................................................................................................................................... 4-2 EXTERNAL BATTERY PREVENTIVE MAINTENANCE ............................................................................................... 4-2 TROUBLESHOOTING ............................................................................................................................................... 4-3 REMOVAL/REPLACEMENT PROCEDURES - OPERATOR ........................................................................................... 4-4 Audio Accessory Removal/Replacement . ....................................................................................................... 4-4 Antenna Removal/Replacement. ...................................................................................................................... 4-4 Battery Removal/Replacement. ........................................................................................................................ 4-5 RADIO DISASSEMBLY ............................................................................................................................................ 4-5 CHAPTER 5 BATTERY CHARGERS ............................................................................................................ 5-1 GENERAL INFORMATION .................................................................................................................................. 5-1 PHYSICAL CHARACTERISTICS ................................................................................................................................ 5-2 Weight and Dimensions ................................................................................................................................... 5-2 Temperature ..................................................................................................................................................... 5-2 ELECTRICAL CHARACTERISTICS ............................................................................................................................ 5-2 PERFORMANCE ...................................................................................................................................................... 5-2 OPERATING INDICATIONS ...................................................................................................................................... 5-3 CHAPTER 6 ACCESSORIES AND ANCILLARY EQUIPMENT .............................................................. 6-1 GENERAL ............................................................................................................................................................... 6-1 AVAILABLE ACCESSORIES AND ANCILLARY EQUIPMENT FOR THE LIBERTYTM RADIO ...................................... 6-1 Antennas .......................................................................................................................................................... 6-1 Batteries ........................................................................................................................................................... 6-2 Battery Chargers .............................................................................................................................................. 6-2 Cases / Holsters ................................................................................................................................................ 6-3 Audio Accessories ............................................................................................................................................ 6-3 Cables ............................................................................................................................................................... 6-4 Surveillance Equipment ................................................................................................................................... 6-4 CHAPTER 7 GLOSSARY ................................................................................................................................. 7-1 ACRONYMS’ ...................................................................................................................................................... 7-1 DEFINITIONS .......................................................................................................................................................... 7-2 APPENDIX A – QUICK REFERENCE GUIDE .................................................................................................. 7-1 INDEX ..........................................................................................................................................................INDEX - 1
FRONT MATTER Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION vii LIST OF FIGURES FIGURE 1-1 LIBERTYTM RADIO ................................................................................................................................... 1-0 FIGURE 1-1 LIBERTYTM RADIO PHYSICAL CHARACTERISTICS .................................................................................... 1-4 FIGURE 1-2 KEYPAD ................................................................................................................................................... 1-7 FIGURE 1-3 LIBERTY SPECIAL “HOT KEYS” ............................................................................................................... 1-8 FIGURE 1-4 FOUR-WAY NAVIGATION BUTTONS WITH ENTER BUTTON ..................................................................... 1-9 FIGURE 1-5 PROGRAMMABLE SIDE BUTTONS ........................................................................................................... 1-10 FIGURE 1-6 LOCATION OF LED ................................................................................................................................ 1-11 FIGURE 1-7 SIDE CONNECTOR .................................................................................................................................. 1-12 FIGURE 1-8 ANTENNA CONNECTOR.......................................................................................................................... 1-13 FIGURE 1-9 BATTERY CONNECTOR .......................................................................................................................... 1-14 FIGURE 2-1 LIBERTYTM HOME SCREEN DISPLAY (SAMPLE) ....................................................................................... 2-2 FIGURE 2-2 DEFAULT “SPLASH” SCREEN ................................................................................................................... 2-2 FIGURE 2-3 LIBERTYTM HOME SCREEN DISPLAY (SAMPLE) ....................................................................................... 2-3 FIGURE 2-4 OPERATING SCREEN – “HOME” SAMPLE SCREEN .................................................................................... 2-4 FIGURE 2-5 OPERATING SCREEN – SOFTKEYS MENU ................................................................................................. 2-5 FIGURE 2-6 SELECT MENU SCREEN ......................................................................................................................... 2-7 FIGURE 2-7 VIEW MENU SCREEN.............................................................................................................................. 2-8 FIGURE 2-8 PROGRAM MENU SCREEN – P25 CHANNEL TYPE ................................................................................. 2-9 FIGURE 2-9 PROGRAM MENU SCREEN – ANALOG NARROWBAND (AN) ............................................................... 2-12 FIGURE 2-10 PROGRAM MENU SCREEN – ANALOG WIDEBAND (AW) ................................................................. 2-14 FIGURE 2-11 RADIO INFORMATION MENU SCREEN ........................................................................................... 2-18 FIGURE 2-12 MAINTENANCE MENU SCREEN ....................................................................................................... 2-19 FIGURE 3-1 RADIO ON/OFF/VOLUME KNOB AND ZONE SELECT ............................................................................. 3-2 FIGURE 3-2 MENU ACCESS ......................................................................................................................................... 3-3 FIGURE 3-3 RADIO ON/OFF/VOLUME KNOB ............................................................................................................. 3-4 FIGURE 3-4 P25 UNIT TO UNIT CALL ......................................................................................................................... 3-5 FIGURE 4-1 MAINTENANCE MENU SCREEN ............................................................................................................... 4-1
FRONT MATTER viii Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION LIST OF TABLES TABLE 1- 1 EQUIPMENT CHARACTERISTICS ............................................................................................................... 1-2 TABLE 1- 2 TECHNICAL CHARACTERISTICS ............................................................................................................... 1-3 TABLE 1-3 PHYSICAL DESCRIPTION ........................................................................................................................... 1-5 TABLE 1-4 KEYPAD CHARACTERS .............................................................................................................................. 1-8 TABLE 1-5 LED INDICATORS ................................................................................................................................... 1-11 TABLE 2-1 STATUS AREA SYMBOLS ........................................................................................................................... 2-3 TABLE 2-2 CONTEXT AREA DESCRIPTIONS ................................................................................................................ 2-4 TABLE 2-3 SOFTKEY MENU OPTIONS ......................................................................................................................... 2-6 TABLE 2-4 FUNCTIONAL CATEGORY OPTIONS ........................................................................................................... 2-6 TABLE 2-5 SELECT MENU OPTIONS ......................................................................................................................... 2-7 TABLE 2-6 VIEW CHANNEL PARAMETERS .................................................................................................................. 2-8 TABLE 2-7 PROGRAM MENU – P25 CHANNEL TYPE ............................................................................................. 2-10 TABLE 2-8 PROGRAM MENU – ANALOG NARROWBAND (AN) .............................................................................. 2-12 TABLE 2-9 PROGRAM MENU – ANALOG WIDEBAND (AW) .................................................................................. 2-15 TABLE 2-10 CTCSS TONES AND CODES .................................................................................................................. 2-17 TABLE 2-11 CDCSS CODES ..................................................................................................................................... 2-17 TABLE 2-12 MAINTENANCE MENU OPTIONS ....................................................................................................... 2-20 TABLE 3-1 SCAN AND PRIORITY SCAN SIDE BUTTON OPTIONS .................................................................................. 3-7 TABLE 4-1 OPERATOR TROUBLESHOOTING GUIDE .................................................................................................... 4-3 FIGURE 5-1 LIBERTYTM SINGLE-BAY CHARGER ......................................................................................................... 5-1 TABLE 5-2 BATTERY CHARGER WEIGHTS AND DIMENSIONS ..................................................................................... 5-2 TABLE 5-3 CHARGING AND STORAGE TEMPERATURES .............................................................................................. 5-2 TABLE 5-4 CHARGING AND STORAGE TEMPERATURES .............................................................................................. 5-2 TABLE 5-5 CHARGER PERFORMANCE ......................................................................................................................... 5-2 TABLE 5-6 SINGLE-BAY CHARGE STATUS INDICATORS ............................................................................................. 5-3 TABLE 6-1 ANTENNA VERSIONS ................................................................................................................................ 6-1 TABLE 6-2 LIBERTYTM BATTERIES ............................................................................................................................ 6-2 TABLE 6-3 LIBERTYTM BATTERY CHARGERS ............................................................................................................. 6-2 TABLE 6-4 LIBERTYTM CASES / HOLSTERS ................................................................................................................ 6-3 TABLE 6-5 LIBERTYTM AUDIO ACCESSORIES ............................................................................................................. 6-3 TABLE 6-6 LIBERTYTM CABLES ................................................................................................................................. 6-4 TABLE 6-7 LIBERTYTM SURVEILLANCE EQUIPMENT .................................................................................................. 6-4
FRONT MATTER Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION ix RADIO FREQUENCY ENERGY SAFETY INFORMATION This THALES transceiver has been evaluated and complies with the standards listed below, in regards to Radio Frequency (RF) energy and electromagnetic energy (EME) generated by the transceiver. • FCC RF exposure limits for Occupational Use Only. RF Exposure limits adopted by the FCC are generally based on recommendations from the National Council on Radiation Protection and Measurements, & the American National Standards Institute. • FCC OET Bulletin 65 Edition 97-01 Supplement C • American National Standards Institute (C95.1 . 1992) • American National Standards Institute (C95.3 . 1992) WARNING: This THALES transceiver generates RF EME while transmitting. RF EME (Radio Frequency Electric & Magnetic Energy) has the potential to cause slight thermal or heating effects to any part of your body less than the recommended distance from this radio transmitter’s antenna. RF energy exposure is determined primarily by the distance to and the power of the transmitting device. In general, RF exposure is minimized when the lowest possible power is used or transmission time is kept to the minimum required for consistent communications, and the greatest distance possible from the antenna to the body is maintained. The transceiver has been designed for and is classified for Occupational Use Only. Occupational/ controlled exposure limits are applicable to situations in which persons are exposed to RF energy as a consequence of their employment, and such persons have been made aware of the potential for exposure and can exercise control over their exposure. This means you can use the transceiver only if you are aware of the potential hazards of operating a transceiver and are familiar in ways to minimize these hazards. This transceiver is not intended for use by the general public in uncontrolled environments. Uncontrolled environment exposure limits are applicable to situations in which the general public may be exposed to RF energy, or in which the persons who are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. The following list provides you with the information required to ensure that you are aware of RF exposure and of how to operate this transceiver so that the FCC RF exposure limitations are not exceeded. • Do not transmit for more than 50% of the total transceiver use time; transmitting over 50% of the total use time may exceed the limits in accordance to the FCC RF exposure requirements. Nominal transceiver operation is 10% transmission time, 10% reception time, and 80% stand-by time. • Use only the specified antenna for this transceiver; this may be either the antenna provided with the transceiver or another antenna authorized by THALES.  CAUTION To ensure that your exposure to RF EME is within the FCC limits for occupational use, you must observe and adhere to the above points.
FRONT MATTER x Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION RF EXPOSURE GUIDELINES To ensure that exposure to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines: • DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may cause the FCC RF exposure to be exceeded. A proper antenna is the antenna supplied with the radio or an antenna specifically authorized by Thales Communications Inc. (Refer to Table 6-1, Antenna Versions) • ALWAYS use Thales authorized accessories (antenna, batteries, speaker/mic, etc…). When worn on the body, always place the radio in a Thales recommended clip or holster meant for this product. The use of other than recommended or approved body-worn accessories may result in RF exposure levels which exceed the FCC Occupational/Controlled environment RF exposure limits. (Refer to Chapter 6 for a complete listing of Available Accessories and Ancillary Equipment authorized for use on the LibertyTM Radio. • ALWAYS keep the radio and its antenna away from the body and face when transmitting to ensure FCC RF exposure compliance requirements are not exceeded: Face with NO Accessory Radio: 2.5 cm Antenna: 5.5 cm Body worn using belt clip Radio: 1.6 cm Antenna: 2.0 cm Body worn using belt holster Radio 2.0 cm Antenna: 2.2 cm ELECTROMAGNETIC INTERFERENCE COMPATIBILITY Electronic devices are susceptible to electromagnetic interference (EMI) if they are not adequately shielded or designed for electromagnetic compatibility. Because this transceiver generates RF energy, it can cause interference to such equipment. • Turn OFF your transceiver where signs are posted to do so. Hospitals and health care facilities use equipment that is sensitive to electromagnetic radiation. • Turn OFF your transceiver while on board an aircraft when so instructed. Use of the transceiver must be in accordance with airline regulations and/or crew instructions. “OCCUPATIONAL USE ONLY” RADIO The LibertyTM Radio generates RF electromagnetic energy during transmit mode of operation. This radio is designed and classified for “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards and the ways to minimize such hazards. This radio is NOT intended for use by the General Population in an uncontrolled environment. LIBERTYTM RADIO COMPLIANCE WITH FCC PART 15 RULES This device complies with Part 15 of the FCC Rules. Operation is subject to condition that this device does not harmful interference.
FRONT MATTER Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION xi SAFETY SUMMARY The following are general safety precautions that are not related to any specific procedure, and do not appear elsewhere in this manual. These Safety Summaries are recommended precautions that all personnel must understand and apply during any given phase of operation and maintenance. Each chapter has other specific warnings and cautions. KEEP AWAY FROM LIVE CIRCUITS Personnel must at all times observe all safety regulations. Do not replace components or make adjustments inside equipment with power turned on. Under certain conditions, dangerous voltages may exist when the power switch is in the off position due to charges retained by capacitors. To avoid injury, always remove power and discharge and ground a circuit before touching it. VOLTAGES WITHIN THIS EQUIPMENT ARE HIGH ENOUGH TO ENDANGER LIFE. (Applies to battery chargers only) Covers are not to be removed except by persons qualified and authorized to do so and these persons should always take extreme care once the covers have been removed. HAZARDS OF ELECTROMAGNETIC RADIATION TO ORDNANCE (HERO) DO NOT operate the radio within 27 feet (8 meters) of any type of fuzed ordnance. Operating the radio in close proximity to ordnance MAY induce or otherwise couple currents and/or voltages of magnitudes large enough to initiate electro-explosive devices or other sensitive explosive components of weapon systems, ordnance, or explosive devices. CAUTION - LITHIUM ION BATTERIES Li-ion batteries have a very high energy density. Exercise precaution when handling and testing. Do not short circuit, overcharge, crush, mutilate, nail penetrate, apply reverse polarity, expose to high temperature or disassemble. High case temperature resulting from abuse could cause physical injury. REPAIRS, ALTERATIONS TO EQUIPMENT Repairs to this equipment should be made only by an authorized technician or facility designated by Thales. Any repairs, alterations, or substitutions of recommended parts made by the user to this equipment not approved by the manufacturer could void the user’s authority to operate the equipment in addition to Thales’s Warranty.
FRONT MATTER xii Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION NOTATIONS USED IN THIS MANUAL Throughout this manual, there are WARNING, CAUTION, or NOTE Statements that emphasize safety hazards, or care that should be observed. WARNING: A WARNING Statement is an operation procedure, practice, or other condition that might result in injury or death if not carefully observed. Do not proceed beyond a WARNING symbol until the conditions identified are fully understood or met.  CAUTION A CAUTION Statement indicates an operational procedure, practice or other condition, which, if not performed correctly or adhered to, could result in a risk of danger, damage to the equipment, or severely degrade equipment performance. ! NOTE A NOTE Statement that calls attention to supplemental information that may improve system performance or clarify a process or procedure.
FRONT MATTER Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION xiii FOREWORD ! NOTE The radio operation (man-machine interface) shown in this manual reflect Radio Software Version 70 and PC Programmer Version 00.00.01.14. Some screens do not correspond to those in earlier radio software or PC Programmer versions. The organization of the LibertyTM User’s Guide is as follows: a. Chapter 1 Getting to Know the Radio. This chapter provides general information for the LibertyTM Radio including equipment description and purpose. b. Chapter 2 Display / Menu Screens – This chapter covers information covering the various displays / menu screens that can be found on the radio. c. Chapter 3 Operating Instructions – This chapter describes the operating instructions for the radio. d. Chapter 4 Maintenance - This chapter provides instructions required for on-equipment and off-equipment preventive and corrective maintenance of the LibertyTM Radio. e. Chapter 5 Battery Chargers – This chapter provides a brief overview on the operation of the chargers . f. Chapter 6 Accessories / Ancillaries – This chapter provides a complete listing of accessories and ancillaries used with the LibertyTM Radio. g. Chapter 7 Glossary - The glossary provides a definition of the special terms and acronyms used in this document. h. Index i. Attachments – Quick Reference Guide (QRG)
GETTING TO KNOW THE RADIO 1-0 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Figure 1-1 LibertyTM Radio
GETTING TO KNOW THE RADIO Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 1-1 CHAPTER 1 GETTING TO KNOW THE RADIO Description Page Number General Information 1-1 Equipment Characteristics 1-2 Technical Characteristics 1-3 LibertyTM Radio – Location of Controls and Indicators 1-4 Controls and Indicators 1-7 Controls 1-7 Special “Hot Keys” 1-8 Four Way Navigation Buttons with ENT Button 1-9 Indicators 1-10 LCD and Keypad Backlight 1-11 LED Indicators 1-11 Connectors 1-12 GENERAL INFORMATION The LibertyTM Multi-Band Radio is a portable, hand-held, battery operated transceiver capable of providing both secure and non-secure communications. The radio is software upgradeable in the field, and selected features are capable of being enabled and disabled on a per radio basis. In addition, multiple software loads will be available with encryption support added or removed. The LibertyTM Multi-Band radio is designed to provide Public Safety communications, both voice and data, in the following frequency bands • VHF (136-174 MHz), • UHF (380-520 MHz), • 700 MHz (763-775/793-805 MHz), and • 800 MHz (806/851-824/869 MHz) The LibertyTM Radio is designed to be extremely easy-to-use and programmable intuitively via either Keypad or PC. The LibertyTM Radio consists of the following items: • LibertyTM Multi-band portable radio • Multi-band Antenna • Lithium-Ion Battery
GETTING TO KNOW THE RADIO 1-2 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION • Standard Battery Charger • Belt Clip EQUIPMENT CHARACTERISTICS Table 1- 1 Equipment Characteristics Characteristics Specification Modes of Operation • Analog 12.5/25 kHz • P25 Digital (12.5 kHz), Conventional • P25 Trunking (Future) Channel Spacing • 12.5 / 25 kHz channels • 2.5 / 3.125 kHz Frequency Increments Frequency Stability • 1.5 ppm (-30°C (22°F ) to + 60°C (140°F)) Interoperability • Legacy Analog FM Radios • P25 Digital Radios • P25 Trunking Systems (Future) Programmable Channels Initial Release • 1 banks (Groups of Zones) • 16 Zones (up to 256 Channels) • User Programmable from o Front Panel Menu o PC Programmer Production Release • Up to 2608 Conventional Channels or Trunked Talkgroups (Any Combinations) • 10 banks (Groups of Zones) • 175 Zones (up to 16 channels / talkgroups each) • 3 additional event zones with up to 16 channels / talkgroups each) • User Programmable from o Front Panel Menu o PC Programmer o Radio to Radio Cloning • Clear / Encrypted Selection on a Channel-by-Channel or Talkgroup Base • Password Protected to Limit Access
GETTING TO KNOW THE RADIO Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 1-3 TECHNICAL CHARACTERISTICS Table 1- 2 Technical Characteristics Characteristics Specification Weight LibertyTM Radio including battery ~28 ounces (794 grams) Dimension 2.5” W x 1.9” D x 7” L (excluding antenna and knobs) 6.4cm W x 4.8cm D x 17.8 cm L (excluding antenna and knobs) Operating Temperature (-30°C* (22°F ) to + 60°C (140°F)) (*cold starts below -25°C may require a 3 minute warm-up for full specification compliance) Storage Temperature Low Temperature – minimum of -40°C (-40°F) for 24 hours High Temperature -- maximum of 85°C (+85°F) for 24 hours Operational Low Pressure 15,000 feet operational Storage Low Pressure Exposure to storage at 30,000 ft. Charging Temperature 0°C (32°F) to + 45°C (113°F) Rechargeable Battery Operating Temperature Range -20°C (-4°F) to + 60°C (140°F) Rated Power UHF – 5W VHF – 5W 700 MHz – 2.5W 800 MHz – 3.0W
GETTING TO KNOW THE RADIO 2-4 Doc No. 84403 Rev 2 THALES COMMUNICATIONS, INC PROPRIETARY INFORMATION LIBERTYTM RADIO – LOCATION OF CONTROLS AND INDICATORS The LibertyTM Radio Physical Features are as shown in the figure below. Figure 2-1 LibertyTM Radio Physical Characteristics
GETTING TO KNOW THE RADIO Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 1-5 Table 1-3 Physical Description Item No. Description Programmed by PC Programmer 1 Channel Switch – This switch can be programmed to select any 16 settings, (not all positions need be programmed).  2 2-Position Programmable Switch – Although often referred to as the “Encryption Switch”, this switch is actually a programmable switch. This switch can be programmed to select any two settings. There is no “typical” setting for this switch. Current Version -- EXT/INT Audio (“ ” EXT and “0” INT)  3 Antenna connector – Antenna connects to the radio here for TX and RX of RF signals. 4 Status LED – Used to visually indicate various states of the radio. May be solid RED, GREEN, or YELLOW-ORANGE, or flashing individual colors or combinations of colors, depending on the radio state. 5 Speaker – radio internal speaker 6 Programmable Soft-key Button 1 – This button activates the feature or function displayed immediately above it on the color display. Additional entries are accessed by scrolling through the selections using the left/right navigation buttons. The features on the display can be programmed to select any programmable function of the radio.  7 Programmable Soft-key Button 3 – This button activates the feature or function displayed immediately above it on the color display. Additional entries are accessed by scrolling through the selections using the left/right navigation buttons. The features on the display can be programmed to select any programmable function of the radio.  8 Programmable Soft-key Button 2 – This button activates the feature or function displayed immediately above it on the color display. Additional entries are accessed by scrolling through the selections using the left/right navigation buttons. The features on the display can be programmed to select any programmable function of the radio. Current Version – Locked to PRIV Call on P25  9 Keypad – Used to enter alpha-numeric and symbols similar to a cell phone. 10 4-Way Navigation Buttons with Enter – UP/DOWN/LEFT/RIGHT/ENTER buttons used to navigate around the Color Display and highlight displayed icons or fields. The ENTER button is used to “enter” the feature highlighted, which may be a menu, a programming option, or other function as programmed into the radio. 11 Microphone – radio internal microphone 12 Color Display – Color LCD for the display of radio status and other information.
GETTING TO KNOW THE RADIO 1-6 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Item No. Description Programmed by PC Programmer 13 3-Position Programmable Switch – This switch can be programmed to select any three settings. Typically, this switch is programmed for 3-different Zones/Groups. Current Version – Locked to Zones 1, 2, and 3.  14 ON/OFF/Volume Control Knob – Used to turn the radio ON & OFF, and to control the volume level for the internal speaker when the radio is on. The most counter-clockwise position, (first position), is radio OFF; the next clockwise position, (second position), is radio ON with the internal speaker muted; the next 14 clockwise positions, (positions 3 through 16), are radio ON while sequencing through the lowest to highest volume settings on the internal speaker. 15 Side Button 1 – This button can be programmed to select any feature. Current programmable functions are : Disabled, Ni/Low Power, Monitor, Scan, Priority Scan, and Talkaround.  16 Side Button 2 – This button can be programmed to select any feature Current programmable functions are : Disabled, Ni/Low Power, Monitor, Scan, Priority Scan, and Talkaround.  17 Side Button 3 – this button can be programmed to select any feature. Current programmable functions are : Disabled, Ni/Low Power, Monitor, Scan, Priority Scan, and Talkaround.  18 PTT (Push-to-Talk) Button – Press and Hold button used to initiate a call, i.e., transmit on a channel. 19 Battery – Provides DC power to the radio. 20 Emergency Button – Although commonly referred to as the “Emergency Button”, this PRESS & Hold button is actually a programmable button. This button can be programmed to cause the radio to enter any radio feature/state. Typically, this button is programmed to cause the radio to enter into an “Emergency” mode of operation.  21 Side Connector – Used to connect to accessories and devices, PC Programmer (i.e., PC), KFD, etc. Note: A “” indicates that this function is programmable via the PcProgrammer.
GETTING TO KNOW THE RADIO Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 1-7 CONTROLS AND INDICATORS CONTROLS The keypad (Refer to Figure 1-2) for the radio provides an interface to the radio’s features. The keypad functions are similar to a standard cell phone or telephone keypad when entering numeric digits. Figure 1-2 Keypad When the keypad is used to edit a list, each key can generate different characters of the alphabet (refer to Table 1-4 or a complete list of keypad characters.) By default, the first letter in each word will automatically be capitalized; the remaining letters in the word will automatically be lower case. However, the user may override this by pressing to switch between upper case, lower case, and automatic case. To select the case of an individual letter, press before pressing the key. If the entry being edited is a numeric, such as frequency, then the keypad will generate only numbers. For example: L e t ‘ s e a t .
GETTING TO KNOW THE RADIO 1-8 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Table 1-4 Keypad Characters Key Number times the key is pressed 1 2 3 4 5 6 7 8 9 Space 0 ! ? , ; : ( ) . 1 / - + < = > A B C 2 D E F 3 G H I 4 J K L 5 M N O 6 P Q R S 7 T U V 8 W X Y Z 9 Switches letter case # * & " ' % $ Special “Hot Keys” Figure 1-3 Liberty Special “Hot Keys” ENT Button
GETTING TO KNOW THE RADIO Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 1-9 ENT Button While on the MAIN Screen – and only on this screen – the ENT button (refer to Figure 1-3) on the Navigation keypad acts as a hotkey to display the SELECT MENU screen. • Pressing and holding the ENT hotkey button for more than ½ second displays the SELECT MENU Screen. Four-Way Navigation Buttons with Enter Button The Navigation, (Left/Right/Up/Down) (refer to Figure 1-4), buttons are used to scroll through the radio’s lists, or items in the display, or both. When an item/icon is highlighted, the ENT button – in the center of the Navigation buttons – is used to enter the highlighted function or screen. ! NOTE When the OPERATING/MAIN Screen is displayed, the ENT button functions as a “hotkey” short-cut to the SELECT MENU Screen. ! NOTE The screen names “MAIN” and “OPERATING” and “HOME” are used interchangeably throughout this document. Figure 1-4 Four-Way Navigation Buttons with Enter Button Navigational Keys
GETTING TO KNOW THE RADIO 1-10 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Side-Buttons The three (3) side buttons (refer to Figure 1-5), can be preprogrammed to select variety of features. Programming is achieved using the PcProgrammer. Currently, these buttons can each be set for Hi/Low Power, Monitor, Scan, Priority Scan, or Talk Around. Figure 1-5 Programmable Side Buttons
GETTING TO KNOW THE RADIO Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 1-11 INDICATORS LCD and Keypad Backlight The user may turn on the backlighting for the display, keypad, and channel numbers (around the 16-position Select knob), by pressing any key or button. These lights will remain on for a pre-determined time period before they turn off automatically. LED Indicators The LED on the top of the radio indicates the radio’s operating status. Table 1-5 LED Indicators LED Indicator What it Means RED Radio Transmitting Flashing RED Low Battery (while transmitting) GREEN Receiving/Busy Channel Indication OFF Standby Figure 1-6 Location of LED LED Indicator
GETTING TO KNOW THE RADIO 1-12 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Connectors Side Connector The side connector (Refer to Figure 1-7) is a 20-pin connector located on the right side of the radio. This connector is used for multiple functions, including interfacing with the Radio Programmer, Accessories, Cloning and Data Mode cables. Figure 1-7 Side Connector Side Connector
GETTING TO KNOW THE RADIO Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 1-13 Antenna Connector The antenna connector (Refer to Figure 1-8) is a male type connector on the top of the radio. It is recommended that an antenna ALWAYS be connected to the radio when transmitting, even though the radio includes protective circuits to prevent damage from transmitting without an antenna. An antenna should be connected whenever the radio is immersed. ! NOTE It is recommended that an antenna ALWAYS be connected to the radio when transmitting. Figure 1-8 Antenna Connector Antenna Connector
GETTING TO KNOW THE RADIO 1-14 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Battery Connector The battery connector is a 4-pin connector located on the back of the radio. The battery is connected to the radio by inserting the top of the battery under the flap at the top of the radio and snap down into place. Figure 1-9 Battery Connector Battery Connector Underside of Battery
DISPLAY / MENU SCREENS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 2-1 CHAPTER 2 DISPLAY / MENU SCREENS GENERAL INFORMATION This section describes the Display / Menu Screens of the radio. This chapter contains the following: Description Page Number General Information 2-1 Display / Menu Screens 2-2 SPLASH Screen 2-2 HOME Screen 2-3 MENU Screen Display 2-6 SELECT Menu Screen 2-7 VIEW Menu Screen 2-8 PROGRAM Menu Screen 2-9 Channel Type - P25 2-9 Channel Type – Analog Narrowband (AN) 2-12 Channel Type – Analog Wideband (AW) 2-14 RADIO INFORMATION Menu Screen 2-18 MAINTENANCE Menu Screen 2-19
DISPLAY / MENU SCREENS 2-2 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION DISPLAY/ MENU SCREENS The LibertyTM radio display consists of a color QVGA liquid crystal display (LCD). After the initial power-up sequence, the overall display is shown in Figure 2-1. It is divided into three distinct regions as shown in Figure 2-1. Figure 2-1 LibertyTM Home Screen Display (Sample) SPLASH Screen Immediately upon powering on the radio, a SPLASH screen (Figure 2-2) is displayed. The SPLASH screen appears, or “fades in”, first the picture, followed by the “THALES” logo, followed by the “Slogan”, and finally the Version. This screen is displayed while the radio is executing its Power-Up sequence. Figure 2-2 Default “Splash” Screen GIVE ME LIBERTYTM VERSION 00 . 00 MENU PRIV BAKLIT
DISPLAY / MENU SCREENS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 2-3 The makeup of this screen is: • Status Area – displays the Thales Logo horizontally centered in the center of the Status Area on a DARK BLUE Background. • Context Area – displays a “Power-Up” picture. • Softkeys Area – displays a Thales inspired slogan, such as “GIVE ME LIBERTYTM” and the LibertyTM Version information. HOME Screen The Home Screen (refer to Figure 2-3) is the first screen that is displayed after the radio has completed its Power-Up Sequence. Figure 2-3 LibertyTM Home Screen Display (Sample) The operating screen contains three separate areas – Status Area– The area contains symbols that indicate various radio operating conditions. Refer to Table 2-1 for a complete breakdown of these symbols and their meanings. Table 2-1 Status Area Symbols Symbol Indication Received Signal Strength Indication (RSSI) (FUTURE) Battery Conventional ⇒ flashes when battery is low Smart ⇒ the number of bars shown indicate the charge remaining in the battery, flashes when the battery is low. The color also changes to indicate general state: • GREEN – Good to Full Charge • YELLOW – Marginal charge • RED – little if any charge left Monitor (CSQ) - The selected channel is being monitored during conventional operation only. Battery – No Connection with Radio HI LO HI = High TX power setting (Default) LO = Low TX power setting Status Area Context Area SoftKeys Area MENU PRIV TLKARND
DISPLAY / MENU SCREENS 2-4 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Context Area – The Context Area of the Operating screen provides the status of the radio’s current operation, including: – Current Zone Name – Current Channel Name – Zone and Group information – Communication Mode (Talk Around or Repeater) – Channel Type (AN, AW, P25) Figure 2-4 Operating Screen – “Home” Sample Screen Table 2-2 Context Area Descriptions Context Area Details Line #1 Indicates the current selected ZONE name. • A icon is displayed at the beginning of this line to indicate the current zone. Line #2 Indicates the current selected Channel/Talkgroup Name. • A icon is displayed at the beginning of this line to indicate the current channel. • A icon indicates that the channel is operating in UHF frequency range. • A icon indicates that the channel is operating in VHF frequency range. • A icon indicates that the channel is operating in the 700 MHz frequency range. • A icon indicates that the channel is operating in the 800 MHz frequency range. The user may toggle this zone channel scan selection using the softkeys. 800 CHAN 700 CHAN VHF CHAN UHF CHAN MENU PRIV BAKLIT Context Area – Line #1 Context Area – Line #2 Context Area – Line #3 Context Area – Line #4
DISPLAY / MENU SCREENS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 2-5 Context Area Details Line #3 Indicates the presence of an active received channel. The icon shall appear when an active receive carrier is detected and received. This entire row text string is also held for 5.0 seconds after the RX carrier is removed while the radio returns to standby state. If a new call is received, this line is updated to reflect the new receive channel. If the user PTT’s the radio, this line is cleared. Line #4 This line contains four (4) symbols Indicates the following: = Talk-around Mode Indicates the following: = P25 Mode = Analog Narrowband = Analog Wideband Indicates the following: = HI TX power setting (Default) = Low Tx power setting Individual Call or Page/call Alert Call Received. Flashes when an individual call is received. SoftKeys Area – The Softkeys Area of the “OPERATING”, shall display one row of softkeys situated directly above the 3 softkey button as shown in Figure 2-5 . ◄ MENU PRIV BAKLIT ► Figure 2-5 Operating Screen – Softkeys Menu The left (◄) and right (►) arrows indicate that there are more softkey selections programmed that can be displayed by scrolling left or right. If there are no more softkey selections available, the left and right arrows do not appear; instead a  symbol appears. ! NOTE The BOLD values in the parentheses are the defaults for each softkey. VHFHILOHILO■ ■ ■ ■ ■ ■
DISPLAY / MENU SCREENS 2-6 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Table 2-3 Softkey Menu Options Softkey Option Description MENU Changes the display to the SELECT Menu Screen PRIV Changes the display to the P25 Individual Call Contact List in order to make or to cancel an P25 Individual Call. It can also be used to make a Unit to Unit Call. BAKLIT Turns backlight -- (ON/OFF) MENU Screen Displays Once you hit the MENU and the SELECT menu screen appears, the left (◄) and right (►) arrows allows navigation between each screens, by paging left or right. Table 2-4 Functional Category Options Functional Category Description Programming PROGRAM – RED Information/Maintenance VIEW, INFORMATION, MAINTENANCE –BLUE Selection SELECT – GREEN The Softkey Menu entry SAVE is used to save the changes made on any selection or programming screen. If the softkey below SAVE is pressed, the current changes are saved and displayed. If the softkey below SAVE is pressed and held for 2.0 seconds, the current data is saved and the curser returned to the top tab so that the menu screens may be scrolled without scrolling to the top. The Softkey Menu entry EXIT is used to return to the MAIN OPERATING / HOME Menu Screen.
DISPLAY / MENU SCREENS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 2-7 SELECT Menu Screen When highlighted on the Menu Screen, the SELECT Menu Screen is displayed as a window selection list as shown in Figure 2-6. The Up/Down Navigation Keys are used to scroll through the available selections. Figure 2-6 SELECT Menu Screen ! NOTE Currently, the Channel List and Talk Groups on this screen are grayed out. To change channels, use the Channel Knob located on top of the radio. Table 2-5 SELECT Menu Options Channel Parameters Description of function BANK This election allows the user to select a Bank from a drop down list as the active Bank. The Bank selection reverts to the default Bank if the battery is removed for an extended time. When BANK is selected and ENT is pressed, a drop down list appears will appear containing a listing of the BANK selections. ZONE This selection allows the user to select a Zone corresponding to the active/selected Bank. The Zone selection replaces the toggle switch setting if programmed for zone switching. When ZONE is selected and ENT is pressed, a drop down list appears containing the list of ZONE selections. CHAN LIST Lists the current channel name. TALKGRPS Displays the current talk group. TLKARND This selection allows the user to turn ON or OFF talk-around.
DISPLAY / MENU SCREENS 2-8 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION VIEW Menu Screen The VIEW Menu Screen allows the user to view the parameter settings for the selected channel or Talkgroup. Reprogramming is not permitted on this screen. The channel is determined by the channel knob on the top of the radio. While in this screen, changing the channel knob position changes the displayed parameters to reflect the settings for the selected channel. The displayed parameters are shown in Figure 2-7. Figure 2-7 VIEW Menu Screen The displayed channel parameters are defined as follows: Table 2-6 View Channel Parameters Channel Parameters Description Name Channel / Talk-Group Name Type Waveform (AN/AW/P25) Encrypt OFF / AES / DES RX Freq xxx.xxxxx RX SQ Mode Receive Squelch Mode RX SQ Level Receive Squelch Level TX Freq xxx.xxxxx TX SQ Mode Transmit Squelch Mode TX SQ Level Transmit Squelch Level LO PWR Displays Power Level HI PWR Displays Power Level
DISPLAY / MENU SCREENS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 2-9 PROGRAM Menu Screen The PROGRAM Menu Screen (Figure 2-8) allows the user to program the parameter settings for the selected channel. The Up/Down Navigation Keys are used to scroll through the available selections. The displayed parameters are shown in Figure 2-8 for P25, Figure 2-9 for Analog Narrowband (AN) and Figure 2-10 for Analog Wideband (AW). The Channel is selected by using the channel knob on the top of the radio. While in this screen, changing the channel knob position changes the displayed parameters to reflect the parameter settings for the channel selected by the channel knob. Channel Type - P25 Figure 2-8 PROGRAM Menu Screen – P25 Channel Type ! NOTE Only the parameters that are programmable for the selected TYPE are displayed. For example, ENCRYPT has no meaning for Analog; therefore, ENCRYPT is not displayed if the TYPE is either AN (Analog Narrowband) or AW (Analog Wideband).
DISPLAY / MENU SCREENS 2-10 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Table 2-7 PROGRAM Menu – P25 Channel Type Channel Parameters Description NAME Displays the Channel Name. TYPE This selection provides the user with the ability to select the waveform type. When TYPE is selected and ENT is pressed, a drop down list will appear with P25/ AN / AW as the other available options. RX SQ MODE RX SQ MODE is used to set the receive squelch mode and level. For P25, the desired receive NAC and Talkgroup value, as appropriate for the selected P25 squelch mode, is entered in an entry box. When the radio is set for P25, the available selections are as follows: P25 Monitor Normal (NAC) Selective (NAC/Talkgroup) Rx FREQ This selection allows the user to enter the Receive Frequency in MHz as: XXX.XXXXX For RX FREQ, the radio checks the frequency entered versus the band limits, (UHF, VHF, 700 MHz, 800 MHz). The four band limits are as follows: • VHF: 136–174 MHz • UHF: 380–520 MHz • 700 MHz: 763–775 MHz • 800 MHz: 851–869 MHz TX FREQ This selection allows the user to enter the Transmit Frequency in MHz as: XXX.XXXXX For TX FREQ, the radio checks the frequency entered versus the band limits, (UHF, VHF, 700 MHz, 800 MHz). The four band limits are as follows: • VHF: 136–174 MHz • UHF: 380–520 MHz • 700 MHz: 763–775 MHz/793–805 MHz • 800 MHz: 806–824/851–869 MHz For the 700 MHz and 800 MHz bands, the radio also checks the frequency separation of TX and RX for valid values; i.e., for the 700 MHz band, the separation is 30 MHz with Receive the lower RF, while for the 800 MHz band, the separation is 45 MHz with Receive the higher RF. (In the 700/800 bands, the radio can automatically set the second frequency once the first frequency, (typically RX), is entered.) Also, since frequency is in steps of 3.125 and 2.5 kHz only, the radio rounds each entered frequency to the nearest acceptable value. RX NAC P25 NAC RX: 1 – 0xFFF Hex (1 - 4095 Decimal). Excluding the reserved value of 0xF7F (3967) used for repeater functionality. TX NAC P25 NAC TX: 1 – 0xFFF Hex (1 – 4095 Decimal). Excluding the reserved values of 0xF7E (3966) and 0xF7F (3967). RX TG 1 – 65535 Decimal (1 – 0xFFFF Hex).
DISPLAY / MENU SCREENS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 2-11 Channel Parameters Description TX TG 1 – 65535 Decimal (1 – 0xFFFF Hex). ENCRYPT Not enabled this release LO TX PWR This selection allows the user to set the low transmit power setting to any of the values in the following table with default values in bold underlined type: (VHF) (UHF) (700) (800) 0.1 0.1 0.1 0.1 0.5 0.5 0.5 0.5 1.0 1.0 1.0 1.0 2.0 2.0 2.0 2.0 3.0 3.0 2.5 3.0 4.0 4.0 5.0 5.0 HI TX PWR This selection allows the user to set the low transmit power setting to any of the values in the following table with default values in bold underlined type: (VHF) (UHF) (700) (800) 0.1 0.1 0.1 0.1 0.5 0.5 0.5 0.5 1.0 1.0 1.0 1.0 2.0 2.0 2.0 2.0 3.0 3.0 2.5 3.0 4.0 4.0 5.0 5.0 ! NOTE The decimal point is automatically display/entered by the radio as the user types in the frequency value.
DISPLAY / MENU SCREENS 2-12 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Channel Type – Analog Narrowband (AN) Figure 2-9 PROGRAM Menu Screen – Analog Narrowband (AN) Table 2-8 PROGRAM Menu – Analog Narrowband (AN) Channel Parameters Description NAME Displays the Channel and Channel name. TYPE This selection provides the user with the ability to select the waveform type. When TYPE is selected and ENT is pressed, a drop down list will appear with P25/ AN / AW as the available options. RX SQ MODE RX SQ MODE is used to set the receive squelch mode and level. For Analog mode, the desired receive CTCSS or CDCSS value, as appropriate, is entered in an entry box, while the squelch NOISE level contains a drop down selection list with ranges of 0-16, with 0 being open squelch. When the radio is set for AN, the available selections are as follows: RX SQ MODE is selected and ENT is pressed, a drop down list with the Analog selections. Analog CSQ CTCSS Tone (Refer to Table 3-7) CDCSS Code (Refer to Table 3-8) TX SQ MODE TX SQ MODE is used to set the transmit squelch mode and level. For Analog mode, the desired receive CTCSS or CDCSS value, as appropriate, is entered in an entry box, while the squelch NOISE level while the squelch NOISE level contains a drop down selection list with ranges of 0-16, with 0 being open squelch. When the radio is set for AN, the available selections are as follows: TX SQ MODE is selected and ENT is pressed, a drop down list with the either
DISPLAY / MENU SCREENS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 2-13 Channel Parameters Description Analog selections. Analog OFF CTCSS Tone (Refer to Table 2-10) CDCSS Code (Refer to Table 2-11) RXSQLVL This selection allows the user to enter the desired receive squelch level. The available options are 0-16, with 0 being open squelch. TXSQLVL This selection allows the user to enter the desired transmit squelch level when CTCSS or CDCSS squelch mode is selected. Rx FREQ This selection allows the user to enter the Receive Frequency in MHz as: XXX.XXXXX For RX FREQ, the radio checks the frequency entered versus the band limits, (UHF, VHF, 700 MHz, 800 MHz). The four band limits are as follows: • VHF: 136–174 MHz • UHF: 380–520 MHz • 700 MHz: 763–775 MHz • 800 MHz: 806–824/851–869 MHz TX FREQ This selection allows the user to enter the Transmit Frequency in MHz as: XXX.XXXXX For TX FREQ, the radio checks the frequency entered versus the band limits, (UHF, VHF, 700 MHz, 800 MHz). The four band limits are as follows: • VHF: 136–174 MHz • UHF: 380–520 MHz • 700 MHz: 763–775 MHz/793–805 MHz • 800 MHz: 806–824/851–869 MHz For the 700 MHz and 800 MHz bands, the radio also checks the frequency separation of TX and RX for valid values; i.e., for the 700 MHz band, the separation is 30 MHz with Receive the lower RF, while for the 800 MHz band, the separation is 45 MHz with Receive the higher RF. (In the 700/800 bands, the radio can automatically set the second frequency once the first frequency, (typically RX), is entered.) Also, since frequency is in steps of 3.125 and 2.5 kHz only, the radio rounds each entered frequency to the nearest acceptable value ENCRYPT Not enabled this release. LO TX PWR This selection allows the user to set the low transmit power setting to any of the values in the following table with default values in bold underlined type: (VHF) (UHF) (700) (800) 0.1 0.1 0.1 0.1 0.5 0.5 0.5 0.5 1.0 1.0 1.0 1.0 2.0 2.0 2.0 2.0 3.0 3.0 2.5 3.0 4.0 4.0
DISPLAY / MENU SCREENS 2-14 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Channel Parameters Description 5.0 5.0 HI TX PWR This selection allows the user to set the low transmit power setting to any of the values in the following table with default values in bold underlined type: (VHF) (UHF) (700) (800) 0.1 0.1 0.1 0.1 0.5 0.5 0.5 0.5 1.0 1.0 1.0 1.0 2.0 2.0 2.0 2.0 3.0 3.0 2.5 3.0 4.0 4.0 5.0 5.0 Channel Type – Analog Wideband (AW) Figure 2-10 PROGRAM Menu Screen – Analog WideBand (AW)
DISPLAY / MENU SCREENS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 2-15 Table 2-9 PROGRAM Menu – Analog Wideband (AW) Channel Parameters Description NAME Displays the Channel and Channel name. TYPE This selection provides the user with the ability to select the waveform type. When TYPE is selected and ENT is pressed, a drop down list will appear with P25/ AN / AW as the available options. RX SQ MODE RX SQ MODE is used to set the receive squelch mode and level. For Analog mode, the desired receive CTCSS or CDCSS value, as appropriate, is entered in an entry box, while the squelch NOISE level while the squelch NOISE level contains a drop down selection list with ranges of 0-16, with 0 being open squelch. When the radio is set for AN, the available selections are as follows: RX SQ MODE is selected and ENT is pressed, a drop down list with the Analog selections. Analog CSQ CTCSS Tone (Refer to Table 3-7) CDCSS Code (Refer to Table 3-8) TX SQ MODE TX SQ MODE is used to set the transmit squelch mode and level. For Analog mode, the desired receive CTCSS or CDCSS value, as appropriate, is entered in an entry box, while the squelch NOISE level while the squelch NOISE level contains a drop down selection list with ranges of 0-16, with 0 being open squelch. When the radio is set for AN, the available selections are as follows: TX SQ MODE is selected and ENT is pressed, a drop down list with the either Analog selections. Analog OFF CTCSS Tone (Refer to Table 2-10) CDCSS Code (Refer to Table 2-11) RXSQLVL This selection allows the user to enter the desired receive squelch level. The available options are 0-16, with 0 being open squelch. TXSQLVL This selection allows the user to enter the desired transmit squelch level when CTCSS or CDCSS squelch mode is selected. Rx FREQ This selection allows the user to enter the Receive Frequency in MHz as: XXX.XXXXX For RX FREQ, the radio checks the frequency entered versus the band limits, (UHF, VHF, 700 MHz, 800 MHz). The four band limits are as follows: • VHF: 136–174 MHz • UHF: 380–520 MHz • 700 MHz: 763–775 MHz • 800 MHz: 851–869 MHz TX FREQ This selection allows the user to enter the Transmit Frequency in MHz as: XXX.XXXXX For TX FREQ, the radio checks the frequency entered versus the band limits, (UHF,
DISPLAY / MENU SCREENS 2-16 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Channel Parameters Description VHF, 700 MHz, 800 MHz). The four band limits are as follows: • VHF: 136–174 MHz • UHF: 380–520 MHz • 700 MHz: 763–775 MHz/793–805 MHz • 800 MHz: 806–824/851–869 MHz For the 700 MHz and 800 MHz bands, the radio also checks the frequency separation of TX and RX for valid values; i.e., for the 700 MHz band, the separation is 30 MHz with Receive the lower RF, while for the 800 MHz band, the separation is 45 MHz with Receive the higher RF. (In the 700/800 bands, the radio can automatically set the second frequency once the first frequency, (typically RX), is entered.) Also, since frequency is in steps of 3.125 and 2.5 kHz only, the radio rounds each entered frequency to the nearest acceptable value ENCRYPT Not enabled this release. LO TX PWR This selection allows the user to set the low transmit power setting to any of the values in the following table with default values in bold underlined type: (VHF) (UHF) (700) (800) 0.1 0.1 0.1 0.1 0.5 0.5 0.5 0.5 1.0 1.0 1.0 1.0 2.0 2.0 2.0 2.0 3.0 3.0 2.5 3.0 4.0 4.0 5.0 5.0 HI TX PWR This selection allows the user to set the low transmit power setting to any of the values in the following table with default values in bold underlined type: (VHF) (UHF) (700) (800) 0.1 0.1 0.1 0.1 0.5 0.5 0.5 0.5 1.0 1.0 1.0 1.0 2.0 2.0 2.0 2.0 3.0 3.0 2.5 3.0 4.0 4.0 5.0 5.0
DISPLAY / MENU SCREENS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 2-17 If CTCSS is chosen, a drop down list will be made available that contains the 42 valid CTCSS tones and codes as listed in Table 2-10. The CTCSS tones are either provided as the actual audio tone (i.e. 127.3 Hz) or the Code (i.e. 3A). The drop down list provides both – select the required tone. The default value is 67.0 Hz (XZ) (in bold). Table 2-10 CTCSS Tones and Codes 67.0 Hz (XZ) 97.4 Hz (ZB) 141.3 Hz (4A) 203.5 Hz (M1) 69.3 Hz (WZ) 100.0 Hz (1Z) 146.2 Hz (4B) 206.5 Hz (8Z) 71.9 Hz (XA) 103.5 Hz (1A) 151.4 Hz (5Z) 210.7 Hz (M2) 74.4 Hz (WA) 107.2 Hz (1B) 156.7 Hz (5A) 218.1 Hz (M3) 77.0 Hz (XB) 110.9 Hz (2Z) 162.2 Hz (5B) 225.7 Hz (M4) 79.7 Hz (WB) 114.8 Hz (2A) 167.9 Hz (6Z) 229.1 Hz (9Z) 82.5 Hz (YZ) 118.8 Hz (2B) 173.8 Hz (6A) 233.6 Hz (M5) 85.4 Hz (YA) 123.0 Hz (3Z) 179.9 Hz (6B) 241.8 Hz (M6) 88.5 Hz (YB) 127.3 Hz (3A) 186.2 Hz (7Z) 250.3 Hz (M7) 91.5 Hz (2Z) 131.8 Hz (3B) 192.8 Hz (7A) 254.8 Hz (07) 94.8 Hz (2A) 136.5 Hz (4Z) If CDCSS is chosen, a drop down list will be made available that contains the 83 valid CDCSS codes as listed in Table 2-11. The default value is 023 (in bold). Table 2-11 CDCSS Codes 023 114 174 315 445 631 025 115 205 331 464 632 026 116 223 343 465 654 031 125 226 346 466 662 032 131 243 351 503 664 043 132 244 364 506 703 047 134 245 365 516 712 051 143 251 371 532 723 054 152 261 411 546 731 065 155 263 412 565 732 071 156 265 413 606 734 072 162 271 423 612 743 073 165 306 431 624 754 074 172 311 432 627
DISPLAY / MENU SCREENS 2-18 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION RADIO INFORMATION Menu Screen When highlighted on the Menu Screen, the RADIO INFORMATION Menu Screen is displayed as a window select list as shown in Figure 2-11. This screen is for information only. The user cannot change any parameter, including the enabled options on this screen. Figure 2-11 RADIO INFORMATION Menu Screen ! NOTE Please use the following support contacts: Bob DiDonato, Thales Communications, Inc. Mobile: 1-410-908-7678 Email: Bob.DiDonato@thalescomminc.com Scott Glazer, Thales Communications, Inc. Mobile: 1-240-422-2612 Email: scott.glazer@thalescomminc.com For support on any other Thales Equipment, please call 1-800-914-0303.
DISPLAY / MENU SCREENS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 2-19 MAINTENANCE Menu Screen When highlighted on the Menu Screen, the MAINTENANCE Menu Screen is displayed as a window select list as shown in Figure 2-12. The Up/Down Navigation Keys are used to scroll through the available selections. ! NOTE For additional information relating to Maintenance, refer to Chapter 4 of this manual. Figure 2-12 MAINTENANCE Menu Screen ! NOTE This screen is temporarily being used for Downloading Radio configuration file to radio (puts radio in program mode by being on this screen) – for future releases of the radio – this will be automatic. ! NOTE The radio does not transmit or received while on the Maintenance Screen.
DISPLAY / MENU SCREENS 2-20 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Table 2-12 MAINTENANCE Menu Options Channel Parameters Description of Function DATE This selection displays the date in mm/dd/yyyy. CLOCK This selection displays the time in hours:minutes:seconds:tenths of seconds. A Global Setting determine whether a 24 hour or a 12 hour (with AM or PM) time is displayed. ELAPSED TIME This selection displays the total time the radio has been in Transmit mode (PTT pressed), Receive mode (actively receiving radio signals with audio output), and Standby mode (powered on but neither transmitting nor receiving). The time is shown in hours:minutes. IBIT FUTURE -- The IBIT (Initiated Built-In-Test) function runs self-test of the primary radio boards and functions. If there is a failure, the screen will show the test results (PASS or FAIL) for each test. RESET FUTURE -- The RESET function provides a means for the user to “reset” the radio by initiating a “Warm Boot” of the radio. A “Warm Boot” is a restart of the radio by resetting the radio configuration parameters and executing POST, but not performing a battery authentication or powering down the radio. Selecting “OK” and pressing ENT resets the radio by initiating the “Warm Boot”.
OPERATING INSTRUCTIONS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 3-1 CHAPTER 3 OPERATING INSTRUCTIONS GENERAL INFORMATION This section describes the operating procedure for the radio. This chapter contains the following: Description Page Number General Information 3-1 Operating Instructions 3-1 Connecting the Battery 3-1 Connecting the Antenna 3-1 Radio Programming 3-1 Turning on the Radio 3-2 Menu Access 3-3 Transmitting 3-4 Receiving 3-4 P25 Unit to Unit Call 3-5 SCAN – Conventional and Priority 3-5 Using the Programmable Side Buttons 3-8 Squelch Monitor 3-8 Hi/Low Power 3-8 Talk Around 3-8 Modifying Menu Selections – SELECT Menu or PROGRAM Menu 3-9 Changing ZONES 3-9 Screen Saver 3-10 OPERATING INSTRUCTIONS Connecting the Battery The battery is connected to the radio by inserting the top of the battery under the flap at the top of the radio and snap down into place. Connecting the Antenna The antenna is connected to the radio through a connector on top of the radio. Screw the antenna clockwise onto the connector until it is fully seated. Radio Programming Prior to operation for the first time, the radio should be programmed via the PC Programmer. For help in programming a radio using the PC Programmer see the MA6941U PC Programmer's User Manual, Thales part number 84404.
OPERATING INSTRUCTIONS 3-2 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Turning on the Radio Turn on the radio using the On/Off/Volume knob. The radio will go through a boot-up sequence, displaying a blank screen, the Thales Screen, the Liberty Screen and an Operating Screen. The radio has a Power-On-Self-Test (POST) function that checks basic radio functions every time the radio is powered up. Use the switch to set the volume to a comfortable level. Select the desired channel using the Channel Select Switch. The radio is now ready for operation. Figure 3-1 Radio ON/OFF/Volume Knob and ZONE Select ON/OFF/Volume, ZONE Select
OPERATING INSTRUCTIONS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 3-3 Menu Access ! NOTE Refer to Chapter 1 for additional information relating to the navigation keys. ! NOTE When the HOME Screen is displayed, the ENT button functions as a “hotkey” short-cut to the MENU Screen. • Press the MENU softkey or the ENT button to access menus • Once in the MENU’s, the user uses the left (◄) and right (►) arrows allows navigation between each screens, by paging left or right to the applicable Menu. • Press EXIT to return to the HOME Screen. Figure 3-2 Menu Access MENU Softkey NAV ENTER
OPERATING INSTRUCTIONS 3-4 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Transmitting ! NOTE Prior to transmitting, verify that the LED is NOT lit Green (solid or flashing) as this indicates RF traffic on that channel. Wait for it to clear. • To Transmit: – Push the PTT button – Speak into microphone (3-6 inches away) • LED Transmit Indications: – OFF – Not Transmitting or Receiving – RED - Transmitting • Transmitting with Speaker/Mic: – Push PTT on Speaker/Mic – Speak into Speaker/Mic Receiving • Conventional Channels Talkgroups: – Verify PTT is NOT pressed – Audio will come through the Speaker or Speaker/Mic. • LED Receive Indications: – OFF – Not Transmitting or Receiving – GREEN – Receiving Signal • Transmitting with Speaker/Mic: – Push PTT on Speaker/Mic – Speak into Speaker/Mic LED MIC PTT Speaker Figure 3-3 Radio ON/OFF/Volume Knob and ZONE Select
OPERATING INSTRUCTIONS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 3-5 P25 Unit to Unit Call To place a call within your unit, 1. Press the PRIV Softkey from the HOME screen. 2. Enter the Unit ID number. 3. Press enter, then press PTT to initial the call. The Unit ID will be active until a different channel is selected, or the user presses EXIT. ! NOTE The Individual Call or Page icon ( ) will appear on the Operating Screen. Figure 3-4 P25 Unit to Unit Call
OPERATING INSTRUCTIONS 3-6 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Scanning – Conventional and Priority ! NOTE Selection of Channels for scanning is preprogrammed through the PcP. Up to 16 channels can be scanned at a time. ! NOTE Scanning can be performed by pressing one of the pre-programmed side buttons. Enable SCAN 1. Press one of the side buttons that has been pre-programmed to SCAN. ! NOTE A scan bar on the main screen will provided indication that the radio is scanning the channels in the SCANLIST. ! NOTE If the SCAN list is empty or there is no scan list, the user will not be able to select SCAN ON. Priority Scan To enable priority scan, press the pre-programmed side button. When the radio is in Priority Scan, the main screen will show the scan bar, plus any of the following: • “P1” if no priority channels are defined (current channel will become P1) • “P1” if only P1 was defined or only P2 was defined (1 priority channel) • “P2” if P1 and P2 were both defined. The radio will continue to scan using the P1/P2 priority channels, alternating between P1 and P2. 1. If one of the side button has been enabled for Priority Scan , press the side button to enable Priority Scan. ! NOTE If SCAN is not ON, than pressing the programmed “Priority Scan” button just sets the mode to priority scanning. Scanning does not actually turn on until SCAN is set ON.
OPERATING INSTRUCTIONS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 3-7 ! NOTE If no priority channels are defined the radio includes the current channel as the priority (P1) channel. Table 3-1 Scan and Priority Scan Side Button Options Side Buttons Comment PSCAN->SCAN Priority scanning is alternately enabled/disabled on PSCAN press. SCAN->PSCAN-SCAN When priority scanning is running and the SCAN side button is pressed the radio will stop scanning. The next SCAN button press will resume priority scanning (priority scanning persists until power down) Receiving a Voice Call on a Channel in the Scan List If a voice call is received on a channel that is in the scan list, the radio will break squelch on the channel when the call is received. The main screen will “temporarily change to the scan Rx channel, indicating which ZONE, SCAN Channel, frequency, and ID information. ! NOTE When a call is received, the scan function will stop. And when the call has ended, the radio will resume scanning. Monitor Timer The Monitor Timer is the amount of time the radio will sample a channel picked up during a scan before the radio returns to scan operation. At the end of the monitor period, the radio will break reception and continue with the scan sequence. If the signal is still there during the next scan cycle, it will be picked up again. The Monitor Timer is pre-programmed by the PcP. SCAN Hold Timer If Talkback is disabled, the Scan Hold Timer allows a user to monitor a channel that was picked up while scanning prior to re-entering the scan sequence. In addition, if Talkback is disabled, the Talkback Scan Timer is not used. This is required to hear both sides of a conversation for example.
OPERATING INSTRUCTIONS 3-8 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Using the Pre-Programmed Side Buttons The side buttons have been pre-programmed using the PcP. The following information provides a quick summary on how to use each of the buttons. ! NOTE The following information assumes that the side buttons have been pre-programmed using the PcProgrammer. Currently the side buttons can be programmed for HI/Low Power; Monitor, Scan, Priority Scan, and Talk-Around Squelch Monitor Side Button 1. Select an analog channel that has a RX squelch setting of anything other than “0”. 2. Press the Monitor side button. 3. The radio will immediately breaks squelch on the current channel. The channel will remain “open squelch” indefinitely in this mode. 4. To stop monitoring on this channel, press the monitor side button. 5. The radio reverts to its current squelch mode setting. If squelch signal is present on the channel the radio will remain open squelch, otherwise it will close squelch. If a channel or Zone is changed with Monitor Enabled: 1. If a channel or zone is changed on the radio, the radio will immediately open squelch on the new channel (monitor mode remains on). 2. Once the Monitor side button is pressed, the radio will close squelch. 3. The user may change back to the original channel. 4. The original channel is operating with normal squelch settings. HI/LO Power Side Button The Hi/Low Power Side Button provides the user with the capability to switch power setting on any given channel. The main menu will either display a HI or LO icon ( or ) depending on the particular channel power settings. Talk Around ! NOTE The following information assumes that the channel has Talk-Around option has been enabled and that one of the side buttons has been pre-programmed by the PcProgrammer. 1. The user selects a channel that has been programmed for Talk Around. 2. Press the Talk Around side button. When the radio is in Talk-Around, the main screen will display the TA icon ( ). 3. The radio transmits and receives on the same frequency. HILO
OPERATING INSTRUCTIONS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 3-9 Modifying Menu Selections – SELECT Menu or PROGRAM Menu ! NOTE Unless otherwise noted, the following “hints” apply to each menu: • If an entry is grayed out – it cannot be changed by the user. • If a drop down menu appears after ENT is pressed, the user may select from this drop-down menu. • If no drop down screen appears, the user may use the numeric keypad to enter the required information, such as frequency range, RX/TX NAC, RX/TX TG using the numeric keypad. 1) Press the MENU Softkey or press ENT from the HOME screen to enter the menus. 2) Using the left / right arrow keys scroll to the applicable menu. 3) To edit an entry in that menu, press either the up () or down () arrows to scroll to desired line item. The user may either select from drop-down menus or enter data directly using the numeric keypad. 4) After the changes have been completed, hit the SAVE softkey. 5) To move to the next menu, press the up arrow until you reach the top of the menu, then use the left (◄) and right (►) arrows to move to the next menu. ! NOTE If you click EXIT after you have save your changes, you will be returned to the HOME Screen. Changing ZONES The first three (3) zones can be selected by the 3-position switch (FIXED at Zone Select for Initial Release) (Refer to Figure 3-1). Additional zones can be accessed by going to SELECT Menu (as described in Chapter 2).
OPERATING INSTRUCTIONS 3-10 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Screensaver The Liberty ™ Radio is equipped with a screensaver that turns the color display OFF after a period of inactivity (similar to cell-phones) to conserve battery life. The color screen can be re-activated by any of the following actions: • Received call • Press PTT • Change volume or channel • Press any key ! NOTE The ENTER Light stays ON, but maybe difficult to see in bright light.
MAINTENANCE Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 4-1 CHAPTER 4 MAINTENANCE GENERAL INFORMATION This chapter provides operator maintenance instructions for the LibertyTM Radio. This includes operational checkout, inspection and preventive maintenance, troubleshooting, and removal/replacement procedures. This chapter contains the following: Description Page Number General Information 4-1 Operational Checkout 4-2 Radio Preventative Maintenance 4-2 Inspection and Cleaning 4-2 External Battery Preventative Maintenance 4-2 Troubleshooting 4-3 Removal/Replacement Procedures - Operator 4-4 Audio Removal/Replacement 4-4 Antenna Removal/Replacement 4-4 Battery Removal/Replacement 4-5 Radio Disassembly 4-5 Figure 4-1 Maintenance Menu Screen
MAINTENANCE 4-2 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION OPERATIONAL CHECKOUT The LibertyTM radio provides three types of BIT: • POST – Power On Self Test (POST) function that checks the basic radio functions every time the radio is powered up. • CBIT – Continuous Built In Test (CBIT); this series of radio self tests are run in the background during normal operation • IBIT – Initiated Built In Test (IBIT); this series of radio self tests are run when requested by the user (FUTURE) RADIO PREVENTIVE MAINTENANCE Inspection and Cleaning The radio should be occasionally inspected for external damage, such as bent connectors, and wear items, such as loose attaching hardware (screws and setscrews). The radio should be cleaned periodically, particularly after exposure to salt water, sand, or mud. The user should wipe exposed contacts, such as the side connector, battery connector, and audio connector with fresh water and then dry with low pressure air, if available. Small pieces of dirt and debris may infiltrate the grill of the internal speaker and should be cleaned out with a soft brush or blown out with low pressure air (if available) to remove any particles EXTERNAL BATTERY PREVENTIVE MAINTENANCE Lithium-ion batteries will self-discharge over time. If not periodically recharged, the voltage level can get so low that the maximum potential capacity is reduced or the battery may not accept a recharge. In order to prevent the effect of excessive self-discharge, it is recommended that lithium-ion batteries that are not in regular use (e.g., in storage) be regularly recharged to full capacity. However, the LibertyTM Battery has an 18 month shelf life. In ideal situations, it is recommended that the battery be stored at room temperature and low humidity.
MAINTENANCE Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 4-3 TROUBLESHOOTING There are only a limited number of equipment failures that can be corrected by the operator. The following table describes them. Table 4-1 Operator Troubleshooting Guide Symptom Probable Cause Corrective Action Radio does not operate • Battery not properly connected • Before removing battery from the radio, make sure the radio is turn-off first. • Remove and re-install battery – be sure to clean the battery contacts before re-installing the battery. • Battery dead • Either Charge or Replace battery Screen Blank • Radio in screen saver mode • To re-activate the screen – press PTT, change the volume or channel, or press any key. The screen will also be re-activated when a call is received. Cannot communicate with other radio users • Radios set to different frequencies • Set all radios to the same frequency (can be accomplished by loading from PC Programmer). • Radios are set with different CTCSS tones • Set receive and transmit CTCSS tones the same in all radios • Radios set to different modulation types • Set radios to same modulation type External Speaker/Microphone not working (no audio) • External Speaker/Mic not properly installed • Verify speaker / mic is attached correctly. • No audio • Remove and replace the external audio speaker/microphone. • Check the INT/EXT Audio Switch - Current Functionality – EXT/INT Audio (“” EXT and “0” INT) Radio does not scan • SCANLISTS not programmed into radio. • Set SCANLISTS in the PcP and download to the radio. Radio does not communicate with PcProgrammer • PcProgrammer not installed correctly. • Refer to PcProgrammer manual for installation instructions of the software. • PcProgrammer Cable not connected properly • Check cable connections, remove and re-attach PcProgramming cable.
MAINTENANCE 4-4 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION REMOVAL/REPLACEMENT PROCEDURES - OPERATOR The first step for any remove/replace procedure is to power down the equipment. Prior to removing or installing any LibertyTM assembly, remove all accessories (antenna, microphone, etc.). Removal/replacement procedures that are authorized to be performed by the operator are given in the following paragraphs.  CAUTION Before performing removal/replacement procedures, make sure the radio is powered down and the battery is removed from the radio. Audio Accessory Removal/Replacement . Remove/replace the audio accessory as follows: a. Disconnect the audio accessory (e.g., handset), from the audio accessory connector on the side of the radio. b. Replace the audio accessory with a known good one. Antenna Removal/Replacement. Remove/replace antenna as follows: a. Disconnect the antenna from the antenna connector at the top of the radio by first grasping the antenna at the base and turning counterclockwise until unthreaded. Then remove the antenna from the connector. b. Replace the antenna with a known good antenna. Turn antenna clockwise to thread it into position. The antenna should be hand-tightened only.
MAINTENANCE Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 4-5 Battery Removal/Replacement. Remove/replace battery as follows: WARNING: The LibertyTM Li-ion Rechargeable Batteries are fully recyclable and should be disposed of using an appropriate system (such as a special recycling center or via your local government waste disposal center. Never throw your battery out with the household waste or attempt to incinerate. Lithium Ion cells contain non-biodegradable components, hazardous chemical and are prone to aggressive explosion under intense heat.  CAUTION Turn off power before removing the battery by setting the volume switch to the OFF position. Failure to do so may corrupt the programmed configuration and may damage the radio circuitry. a. To disconnect the battery from the radio, press the tabs on both sides to release and lift out from battery. b. To replace the battery, insert the top of the battery, under the flap at the top and click tabs in place at the bottom of the radio. RADIO DISASSEMBLY The LibertyTM Radio is not authorized for disassembly. If the chassis is inadvertently opened, it MUST be returned to Thales Communications Inc for inspection and repair.
MAINTENANCE 4-6 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION THIS PAGE INTENTIONALLY LEFT BLANK
BATTERY CHARGERS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 5-1 CHAPTER 5 BATTERY CHARGERS GENERAL INFORMATION This chapter contains the following: Description Page Number General Information 5-1 Physical Characteristics 5-2 Weight and Dimensions 5-2 Temperature 5-2 Electrical Characteristics 5-2 Performance 5-2 Operating Indications 5-3 For the DHS Initial Pilot Field Trials, only the following chargers will be available: • Standard Single-Bay Charger (PN 1600682-1) The single unit charger (P/N 1600682-1) operates on 90 to 260 VAC power only. The battery charger charges the battery to full charge within three hours, automatically adjusting to the appropriate settings when the battery is inserted. The battery chargers communicate with the circuitry in the battery to monitor charge current, temperature, and voltage to prevent improper charging. Indicator LED’s on the chargers provide status. Figure 5-1 LibertyTM Single-Bay Charger
BATTERY CHARGERS 5-2 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION PHYSICAL CHARACTERISTICS Weight and Dimensions The charger weights and dimensions are shown below: Table 5-2 Battery Charger Weights and Dimensions Charger Configuration Part Number Weight (excluding power cord or vehicle adapter) Size (excluding power cord) Standard Single Unit Charger 1600682-1 < 2 pounds Approx. 5.0 inches (W) x 4.0 inches (H) x 4.0 inches (D). Temperature The chargers’ charging and storage temperature ranges are shown below: Table 5-3 Charging and Storage Temperatures Descriptions Temperature Charging Temperature Range -10°C (+14°F) to +55°C (+131°F) Storage (Non-operational) Temperature Range: -40°C (-40°F) to +85°C (+185°F) Attempting to charge batteries outside the operating temperature range can result in damage to both the chargers and batteries. ELECTRICAL CHARACTERISTICS Table 5-4 Charging and Storage Temperatures Charger Type Electrical Characteristics Single Unit Charger 90 to 264 VAC, 47-63 Hz PERFORMANCE Battery charge time can be affected by various conditions, such as the charger input current. When inserting a battery, make sure it is firmly seated in the charger. The battery chargers communicate with the circuitry in the battery to monitor charge current, temperature, and voltage to prevent improper charging. Indicator LED’s on the chargers provide status. Table 5-5 Charger Performance Charger Configuration Capacity Charge Time Single Bay AC One battery pack Three hours
BATTERY CHARGERS Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 5-3 OPERATING INDICATIONS All versions of the chargers use LEDs to indicate the current charging status and/or charging problems. The meanings of the LED’s are as follows: Table 5-6 Single-Bay Charge Status Indicators Description Indication The charger will display a flashing yellow/green LED indication while it attempts to establish communications with the battery. FLASHING YELLOW/GREEN If the battery temperature exceeds its maximum operating temperature the charger shall set the status LED to solid RED RED If the battery status indicates an over-discharged condition, the charger shall set the status LED to flashing RED FLASHING RED If the battery temperature is below 0°C, the charger shall set the status LED to flashing YELLOW. FLASHING YELLOW During charging, the charger shall set the status LED to solid Yellow. YELLOW When charging is > 90%, the charger shall set the status LED to GREEN. GREEN When a battery/charger error is detected, the charger shall set the status LED to flash RED/GREEN. FLASHING RED/GREEN When a Charger error condition is detected, the charger shall set the status LED to flashing YELLOW/RED. FLASHING YELLOW/RED  CAUTION Do not insert a new battery in the charger until the LED is turned off. ! NOTE If a battery is inserted in the charger while attached to a radio and the radio is ON, the radio fuel gauge may indicate that the battery is fully charged before the charger indicates full charge. ! NOTE The battery can be charged while attached to a radio.
BATTERY CHARGERS 5-4 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION THIS PAGE INTENTIONALLY LEFT BLANK
ACCESSORIES/ANCILLARY EQUIPMENT Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 6-1 CHAPTER 6 ACCESSORIES AND ANCILLARY EQUIPMENT GENERAL This chapter provide information concerning the various accessories that can be used with the LibertyTM Radio manufactured by Thales Communications, Inc., Clarksburg, Maryland. This chapter contains the following: Description Page Number General 6-1 Available Ancillary Equipment for the LibertyTM Radio 6-1 Antennas 6-1 Batteries 6-2 Battery Chargers 6-2 Cases / Holsters 6-3 Audio Accessories 6-3 Cables 6-4 Surveillance Equipment 6-4 AVAILABLE ACCESSORIES AND ANCILLARY EQUIPMENT FOR THE LIBERTYTM RADIO Antennas One antenna is supplied for the LibertyTM Radio: Table 6-1 Antenna Versions Part Number Freq Band 1600678-1 136-174 MHz, 380-520 MHz, 763-869 MHz The antenna is attached via a connector on the top of the radio. A protective screw-on cap is attached to the connector at the base of each antenna to protect the connector from dirt and moisture when the antenna is not attached to the radio.
ACCESSORIES/ANCILLARY EQUIPMENT 6-2 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Batteries The following batteries are available for the LibertyTM Radio: Table 6-2 LibertyTM Batteries Part Number Description 1600691-1 3-Cell Sealed Rechargeable Lithium Ion Battery Pack, 2400 mAh Capacity 1600691-2 6-Cell Sealed Rechargeable Lithium Ion Battery Pack, 4800 mAh Capacity 4102201-501 (FUTURE) AA Clamshell – Black, AA battery (12 AA Alkaline Cells) Clamshell Cassette 4102201-502 (FUTURE) AA Clamshell – Orange, AA battery (12 AA Alkaline Cells) Clamshell Cassette 4102265-501 (FUTURE) Battery Eliminator, powers the radio from external DC power source, provides reverse polarity as well as over voltage and over-current protection for the radio. Accepts nominal 12V DC input voltage. Battery Chargers There are several battery charger options available. Table 6-3 LibertyTM Battery Chargers Part Number Description 1600682-1 Replacement Desktop / Vehicle Charger Unit for PN 6752 1600683-1 (FUTURE) –Advanced Six Slot Lithium-Ion Rechargeable Battery Charger, 120 V AC only, recommended for desktop use only. Also includes battery diagnostics and charge status LED’s. 1600694-1 (FUTURE) Volt DC Cigarette Lighter Adapter for MA6752. 1600695-1 (FUTURE) Replacement 120V AC Power Supply for MA6752. 1600700-1 (FUTURE) Basic Six-Slot Lithium-Ion Rechargeable batter Charger – 120V AC power only. Recommended for desk-top use only. 1600701-1 (FUTURE) Basic Single Slot Lithium-Ion Rechargeable batter Charger – 120V AC power only. Recommended for desk-top use only. MA6752 Desktop/Vehicle DC Lithium Ion Charger Kit, 120 V AC power for desktop use, or 12 VDC vehicle adapter for vehicle charging. Also includes battery diagnostics and charge status LED’s. Refer to Chapter 5 for additional battery charger information, such as characteristics and operation.
ACCESSORIES/ANCILLARY EQUIPMENT Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION 6-3 Cases / Holsters There are several cases / holsters that can be used with the radio: Table 6-4 LibertyTM Cases / Holsters Part Number Description 1600697-1 (FUTURE) Leather Carry Case, D-Ring for Radio with Rechargeable Battery(swivel D-ring included) 1600697-2 (FUTURE) Leather Carry Case, Belt-loop for Radio with AA Clamshell 1600702-1 (FUTURE) Nylon Duty Case for Radio with Rechargeable battery 1600704-1 (FUTURE) Chest Pack Holster – includes space for radio, spare battery, and map pouch. 40508 Spring Loaded Belt Clip – attaches to the battery for a slim profile Audio Accessories There are several cases / holsters that can be used with the radio: Table 6-5 LibertyTM Audio Accessories Part Number Description 1100542-501 (FUTURE) Earphone Kit for Speaker Microphone, plugs into the ear, connects to the Speaker Microphone and “mutes” its’ speaker. 1600696-1 Speaker Microphone, balanced audio, fits in the palm of the hand or attaches to shoulder strap, has its’ own Press-To-Talk (PTT) switch and volume control . 1600696-2 (FUTURE) Speaker Mic with Antenna, balanced audio, fits in the palm of the hand or attaches to shoulder strap, has its’ own Press-To-Talk (PTT) switch and volume control . Includes a top mounted antenna. 1600696-3 (FUTURE) GPS Speaker Mic, balanced audio, fits in the palm of the hand or attaches to shoulder strap, has its’ own Press-To-Talk (PTT) switch and volume control . Also includes GPS receiver. 1600703-1 Audio/Programming Side Connector Adapter, includes 6-pin Hirose connector for audio and keyfill, and USB for programming, cloning, and data transfer. 42803-001 (FUTURE) Lightweight Headset, contains boom microphone, PTT, and in/near ear headset 42804-001 (FUTURE) Heavy Duty Headset, contains boom microphone, PTT, and over the ear headset
ACCESSORIES/ANCILLARY EQUIPMENT 6-4 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Cables The following cables are available for use with the radio: Table 6-6 LibertyTM Cables Part Number Description 1600703-1 Audio/Programming Side Connector Adapter, includes 6-pin Hirose connector for audio and keyfill, and USB for programming, cloning, and data transfer. 1600705-1 (FUTURE) Universal Cable, cable with flying leads to connect radio to user-specific applications 3100965-501 PC Programming Cable Kit, consists of 1600703-1 Audio / Programming side connector adapter and COTS USB Type A male / Mini-AB cable. Used to connect radio to PC for programming. 3100966-501 (FUTURE) Radio Cloning Cable Kit, consists of two (2) 1600703-1 Audio / Programming side connector adapters and COTS USB Mini-AB / Mini-AB cable. Used to connect two radios together for channel cloning. Surveillance Equipment The following surveillance equipment is available for use with the radio: Table 6-7 LibertyTM Surveillance Equipment Part Number Description 1600497-1 (FUTURE) Security Harness (3 Wire), Tan in color with wired earpiece. Requires audio / programming Side Connector Adapter, PN 1600703-1. 1600497-2 (FUTURE) Security Harness (3 Wire), Black in color with wired earpiece. Requires audio / programming Side Connector Adapter, PN 1600703-1. 1600497-3 (FUTURE) Security Harness (2 Wire), Tan in color with wired earpiece. Requires audio / programming Side Connector Adapter, PN 1600703-1. 1600497-4 (FUTURE) Security Harness (2 Wire), Black in color with wired earpiece. Requires audio / programming Side Connector Adapter, PN 1600703-1. 1600497-6 (FUTURE) Wireless Earpiece for Security Harness, requires 1600497-8 neck loop transductor 1600497-8 (FUTURE) Neck Loop Transductor, for wireless earpiece
GLOSSARY Doc No. 84382 INITIAL PILOT FIELD TRIALS VERSION – JAN 2009 THALES PROPRIETARY INFORMATION 7-1 CHAPTER 7 GLOSSARY This glossary contains a listing of Acronyms’ and Definitions that are applicable to the LibertyTM Radio. ACRONYMS’ Term Description AES Advanced Encryption Standard AN Analog Narrowband AW Annalog Wideband BIT Built-In-Test CDCSS Continuous Digital Coded Squelch System CDCSS (also DCS) Continuous Digital Controlled Squelch System CTCSS Continuous Tone-Controlled Squelch System CTCSS Continuous Tone Coded Squelch System DES Data Encryption Standard DTMF Dual-Tone Multi-Frequency (DTMF) GPS Global Positioning System HMI Human-Machine Interface IBIT User Initiated Built-In-Test KEK Key Encryption Kay LCD Liquid Crystal Display LMR Land Mobile Radio NAC Network Access Code OTAP Over-The-Air-Programming OTAR Over-The-Air-Rekeying OTG On-The-Go P25 Project 25 (Digital) POST Power-On-Self Test PTT Push-to-Talk QRG Quick Reference Guide RF Radio Frequency RFSS RF Sub-System RSSI Received Signal Strength Indicator RX NAC Receive Project 25 Network Access Code RX TG Receive Talk Group SMS Short Message Service TEK Traffic Encryption Key TG Talk Group
GLOSSARY 7-2 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Term Description TX NAC Transmit Project 25 Network Access Code TX TG Transmit Talk Group USB Universal Serial Bus XCVR Transceiver DEFINITIONS Term Definition Active Channel The Selected Channel is receiving a signal that is of sufficient strength to overcome the programmed squelch level. Bank A bank is a group of zones. Zones can be assigned to banks during programming. The radio can store up to sixteen banks consisting of 16 zones each. Banks may be assigned names of up to eight characters Carrier Squelch (CSQ) Carrier Squelch (CSQ) is a squelch system based on RF signal present. It is adjustable and is also commonly referred to as Noise Squelch. Channel (xx channels) A group of characteristics, such as transmit / receive, radio parameters, encryption coding. Squelch, modulation, and power settings. Continuous Digital Coded Squelch System (CDCSS) CDCSS is a 23 bit data stream that is sent at a bit rate frequency of 134.4 Hz. It is also filtered prior to sending audio to the speaker. It is not widely used, but is also known by other names such as DCS, DPL, and others. Continuous Tone Coded Squelch System (CTCSS) CTCSS is an audio tone between 67.0 Hz and 254.8 Hz that is attached to the RF signal. It is used to filter out all unwanted communications present on that channel. The tone is filtered out of the signal prior to sending the demodulated audio to the speaker, which is why it is not heard. It is known by several brand names, such as Private Line, PL, Code Guard, and CG amongst others. Typically CTCSS tones are used by repeaters to filter out unwanted signals and also on a direct radio system to enable frequency sharing. Control Channel In a trunking system, one of the channels that is used to provide a continuous, two-way / data communications path between the central control and all radios on the system Conventional Typically refers to radio-to-radio communications, sometimes through a repeater. The user shares a frequency, or frequencies, with other users without the aid of a central controller to assign communication channels. Therefore, the user should monitor each channel before transmitting to avoid interfering with another user who may be transmitting. HOME Channel The Selected Channel when Scan is activated becomes the HOME channel. It is added to the active Scan Plan if not already included. Initial Synchronization Initial synchronization controls the length of time that the radio sends out a bit synchronization pattern.
GLOSSARY Doc No. 84382 INITIAL PILOT FIELD TRIALS VERSION – JAN 2009 THALES PROPRIETARY INFORMATION 7-3 Term Definition Monitor Time The Monitor Time is the amount of time the radio will sample a channel picked up during a scan before the radio returns to scan operation. At the end of the monitor period, the radio will break reception and continue with the scan sequence. The Monitor Time can be programmed for OFF (default) or ON. Network Access Code (NAC) NAC is a digital code providing filtering of unwanted signals. It is typically used to replace the CTCSS tones used for Repeater Access. There are 4096 possible NACs, which are represented either in hexadecimal format (0-FFF) or decimal (0-4095) or both. Open Channel The squelch setting is overridden and the radio is in a constant receive state. Quick Call The QUICK CALL screen displays the various call choices for the user. Radio Set Identifier (RSI) RSI (Radio Set Identifier) is similar to a UnitID, and is typically set to the same value, although not required. It is used to gain access into a network. RSI’s are typically used for network authentication reasons Scan Hold Timer If Talkback is disabled, the Scan hold Timer allows a user to monitor a channel that was picked up while scanning prior to re-entering the scan sequence. In addition, if Talkback is disabled, the Talkback Scan Timer is not used. Selected Channel The Channel/Frequency currently loaded into the radio for Receiving/Transmitting operations. Squelch The muting of audio circuits when received signals levels fall below a pre-determined threshold. With carrier squelch, the user will hear all channel activity which exceeds the radio’s preset squelch level. Standby An operating condition whereby the radio’s speaker is muted but still continues to receive data. Subscriber Unit (SU) Subscriber Unit is a generic name used for a mobile or portable radio unit that can terminate voice or data messages in a radio system. Talk Around Toggles channels enabled for talk around from talk around mode to repeater mode. Talk Around allows radio users to bypass a repeater and talk direct (DIRECT, CAR-CAR, TAC, etc) on a repeater channel. NOTE that the channels MUST have Talk Around enabled from the PC Programmer for this to have any affect. Talk-Group (TG) TG has multiple applications for Project 25. For conventional Project 25 channels, talkgroups are an additional method of breaking up channels, providing a means for several groups to share a repeater without disturbing one another (repeaters can re-transmit only one signal at a time). For trunked channels, talkgroups indicate where the control channel directs the radio. There are 65535 possible TGs, represented in hexadecimal format (FFFFFF) or decimal (0-65535). Transmit (TX) Timeout The radio can be programmed to end transmission automatically after a pre-determined length of time in transmit mode. The radio gives a warning tone and visual indication immediately before ending
GLOSSARY 7-4 Doc No. 84382 Rev 2 THALES COMMUNICATIONS, INC. PROPRIETARY INFORMATION Term Definition transmission. The visual indication ("TIME" on the front display) continues until the radio exits transmit mode or the radio is unkeyed, whichever comes first. UnitID UnitID (Unit Identifier) is a unique parameter that specifies one particular radio. It can be used to identify an incoming call or to initiate a unit-to-unit call. There are over 16,777,215 possible values. Every Project 25 device (handhelds, mobiles, repeaters, base stations, consoles, etc) may be assigned a UnitID Zone A zone is a group of channels. Each zone can be assigned up to 16 channels. The radio can store up to 16 zones, or groups of channels. Zone A zone is a group of channels. Each zone can be assigned up to 16 channels. The radio can store up to 16 zones, or groups of channels.
APPENDIX A APP-A-1 APPENDIX A – QUICK REFERENCE GUIDE
Stats Area Context area Softkey Menu ANTENNAS Antenna PN Frequency Range 1600678-1 136-174 MHz, 380-520 MHz, and 763-869 MHz INITIAL SET-UP 1. Attach a charged LIBERTYTM rechargeable battery to the radio. 2. Attach the antenna by twisting clockwise until it is secured to the radio antenna connector. 3. Use the ON/OFF/Volume control switch on top of the radio to turn on the radio. 4. Turn the channel select switch on top of the radio to the desired operating channel. 5. Use the ZONE Select (A/B/C) Switch to change zones. CONTROLS, INDICATORS, and KEYPADS WHAT IS THE RANGE? • Range is line of sight. If you can see the antenna location, you are in range. • On flat land, horizon is the limiting factor – will get 5-6 miles • Range can be extended by elevating an antenna (or using repeaters) • Best range when antenna is held vertical and away from body. • Use maximum RF output for best range (VHF, UHF: 5W, 700 MHz: 2.5W, 800 MHz: 3W) 2 Operating Screen: Status Area • Received Signal Strength • Battery Charge Status • High / Low TX Power Settings Context Area: • Current Zone Name • Current Channel Name • Zone and Group Information • Communication Mode (Talk-Around or Repeater) • Channel Type (AN, AW, or P25) • P25 ID Display (Also see P25 Unit to Unit Call) • P25 Unit Call Status (Also see P25 Unit to Unit Call) Softkey Menu (displays programmed softkeys only) • Menu • PRIV (Private Call ) • TLKARND (Talk Around) LED Indicators: LED Indicator What it Means RED Radio Transmitting Flashing RED Low Battery (while transmitting) GREEN Receiving/Busy Channel Indication 0FF Standby Programmable Side Buttons: Side Buttons Programmable* Options Each button can be pre-programmed: • Hi/Lo Power • Monitor • Scan • Priority Scan • Talkaround *Pre-Programmed via PcProgrammer 3 LibertyTM Multiband Land Mobile Radio Quick Reference Guide APRIL 2009 Refer to the LIBERTYTM User’s Guide (PN 84382) for additional detailed information on radio operation. Radio Information Menu: VIEWABLE access to all users for: • Manufacturer information • Radio Serial Number (SN) • Software Version • Transceiver Serial Number (SN) • Baseband Serial Number (SN) • Keypad Serial Number (SN) • Customer Support phone number TRANSMITTING / RECEIVING ! NOTE Prior to transmitting, verify that the LED is NOT illuminated GREEN (solid or flashing). This indicates RF traffic on that channel. Wait for it to clear. Transmitting To Transmit: • Push the PTT button • Speak into microphone (3-6 inches) LED Transmit indications • OFF – not transmitting or receiving • RED – transmitting Transmitting with Speaker/Mic • Push PTT on speaker/mic • Speak into speaker/mic 4 Status Area Context Area Softkey menu MENU PRIV TLKRND
MENU ACCESS: ! NOTE Some or all menus may not be accessible due to password protection (future). • PRESS MENU softkey or NAV ENTER button to access menus • Once in MENUS, use the left/right arrow keys to scroll to the desired parameter. • To Edit/Modify an entry -- either press ENT to view the drop down menu. Or use the numeric keypad to enter the required data. • To save changes, first press SAVE, then use the arrow up key to get to the top of the menu, the use the left/right arrows to scroll to the next menu. • To EXIT -- Press EXIT to return to HOME Channel. LCD and Keypad Backlight/Screen Saver The user may turn on the backlighting for the display, keypad, and channel numbers (around the 16-position Select knob), by pressing any key, button, or turning any knob. These lights will remain on for a pre-determined time period before they turn off automatically. ! NOTE Screen Options that are grayed out – are not available this version of software. 6 SELECT Menu ! NOTE The Channel List and Talk Groups on this screen are currently grayed out and cannot be modified in this version of software. To change channels, use the Channel Knob located on top of the radio. • Select Banks (collection of zones) • Select Zones (collection of channels/TG’s) • Turn Talk-Around ON or OFF (FUTURE) VIEW CHANNEL Menu VIEW access only • View Channel parameters 7 PROGRAM CHANNEL Menu PROGRAM CHANNEL – P25 • The Channel name is displayed. • Select the waveform TYPE P25 • Enter the RX/TX Freq • Enter the RX/TX NAC • Enter the RX/TX TG • Turn ENCRYPT ON or OFF • Adjust the LO/HI Power Setting PROGRAM CHANNEL – AN • The Channel name is displayed. • Select the waveform TYPE AN • Enter the RXSQMOD (CSQ, CTCSS, CDCSS) • Enter the TXSQMOD (OFF, CTCSS, CDCSS) • Enter the RXSGLVL (0-16, 0 is open squelch) • Enter the TXSQLVL • Enter the RX/TX Freq ranges • Adjust the LO/HI Power Setting  8 Transmitting/Receiving (cont.): Receiving Conventional Channels Talkgroups • Verify PTT is NOT depressed • Audio will come from speaker (or speaker/mic) LED Receive indications • OFF – not transmitting or receiving • GREEN – receiving signal P25 Unit to Unit Call To place a call within your unit, 1. Press the PRIV Softkey from the HOME screen. 2. Enter the Unit ID number. 3. Press enter, then press PTT to initial the call. The Unit ID will be active until a different channel is selected, or the user presses EXIT. SCAN – Conventional and Priority Enable SCAN – two (2) options: 1. Press the MENU Key and navigate to the scan menu and select SCAN and set to ON. Scanning will start immediately when ON is selected. Once the SCAN function is set to ON, exit the SCAN Menu Screen. OR 2. Press one of the side buttons that has been pre-programmed to SCAN. Enable PRI SCAN – two (2) options: 1. Press the MENU Key and navigate to the scan menu and select SCAN, select PRI SCAN, and set to ON. Scanning will start immediately when ON is selected. Exit the SCAN Menu Screen. OR 2. Press one of the side buttons that has been pre-programmed to PRI SCAN. 5
PROGRAM CHANNEL – AW • The Channel name is displayed. • Select the waveform TYPE AW • Enter the RXSQMOD (CSQ, CTCSS, CDCSS) • Enter the TXSQMOD (OFF, CTCSS, CDCSS) • Enter the RXSGLVL (0-16, 0 is open squelch) • Enter the TXSQLVL • Enter the RX/TX Freq ranges • Adjust the LO/HI Power Setting MAINTENANCE Menu • View Maintenance Information ! NOTE This screen is temporarily being used for Downloading Radio configuration file to radio (puts radio in program mode by being on this screen) – for future releases of the radio – this will be automatic. ! NOTE The radio does not transmit or receive while on the Maintenance Screen. 9 ! NOTE LIBERTYTM RADIOS Please use the following field support contact information: Contact Info: Bob DiDonato, Thales Communications, Inc. Mobile: 1-410-908-7678 Email: Bob.DiDonato@thalescomminc.com Scott Glazer, Thales Communications, Inc. Mobile: 1-240-422-2612 Email: Scott.Glazer@thalescomminc.com APRIL 2009 THALES COMMUNICATIONS, INC. 22605 GATEWAY CENTER DRIVE CLARKSBURG, MD 20871 Customer.Service@thalescommunications.com P/N: 3401448-1, Rev 2 12 Troubleshooting Symptom Probable Cause Corrective Action Radio does not operate • Battery not properly connected • Before removing battery from the radio, make sure the radio is turned-off first. • Remove and re-install battery – be sure to clean the battery contacts before re-installing the battery. • Battery dead • Either Charge or Replace battery Screen Blank • Radio in screen saver mode • To re-activate the screen – press PTT, change the volume or channel, or press any key. The screen will also be re-activated when a call is received. Cannot communicate with other radio users • Radios set to different frequencies • Set all radios to the same frequency (can be accomplished by loading from PC Programmer). • Radios are set with different CTCSS tones • Set receive and transmit CTCSS tones the same in all radios • Radios set to different modulation types • Set Radios to same modulation types External Speaker/Mic not working (no audio) • External Speaker/Mic not properly installed • Verify speaker / mic is attached correctly. • No audio • Remove and replace the external audio speaker/microphone • Check the INT/EXT Audio Switch - Functionality – EXT/INT Audio (“ ” EXT and “0” INT) Radio does not scan • SCANLISTS not programmed into radio • Set SCANLISTS in PcP and download to radio • SCAN is not set to ON • Set SCAN to ON via the SCAN Menu Radio does not communicate with Pc Programmer • Pc Programmer not installed correctly. • Refer to Pc Programmer Manual for installation instructions of the software. • Pc Programmer Cable not connected properly • Check cable connections, remove and re-attach Pc Programmer cable. USB Driver not installed or Network settings not properly configured. 11 RADIO INFORMATION Menu • View Radio Information MAINTENANCE Radio Preventive Maintenance • Check the radio for external damage, such as bent connectors and possible loose hardware. • Periodically clean the radio, especially after exposure to salt water, sand, or mud. • Wipe the exposed contacts (side connector, battery connector) with fresh water and then dry with low pressure air, if available. • Small particles of dirt and debris may infiltrate the grill of the speaker/microphone and should be cleaned using a small brush or low pressure air, if available. Battery and Antenna Installation/Removal 10 ANTENNA • Twist clockwise until fully seated to install • Twist counterclockwise to remove • DO NOT carry radio by antenna. BATTERY • Install and Remove by pressing tabs on both sides to release • To install, insert top of battery under flap at top and click tabs in place at bottom • To remove, press tabs and lift out from battery (recommend turning radio OFF first)
THIS PAGE INTENTIONALLY LEFT BLANK
INDEX Doc No.: 84382 Rev 2 Index-1 INDEX Available Accessories / Ancillary Equipment Antennas ........................................................... 6-1 Audio Accessories ............................................ 6-3 Batteries ............................................................ 6-2 Battery Chargers ............................................... 6-2 Cables ............................................................... 6-4 Cases / Holsters ................................................. 6-3 Surveillance Equipment .................................... 6-4 Battery Chargers Electrical Characteristics .................................. 5-2 General Information .......................................... 5-1 Operating Indications ........................................ 5-3 Performance ...................................................... 5-2 Physical Characteristics .................................... 5-2 Battery Chargers - Physical Characteristics Temperature ...................................................... 5-2 Weight and Dimensions .................................... 5-2 Connectors Antenna Connector ......................................... 1-13 Battery Connector ........................................... 1-14 Side Connector ................................................ 1-12 Controls Four Way Navigation Buttons w/ Enter Button 1-9 Side Buttons .................................................... 1-10 Special............................................................... 1-8 Controls and Indicators Controls............................................................. 1-7 Indicators ........................................................ 1-11 Display / Menu Screens Display/ MENU SCREENS .............................. 2-2 General Information .......................................... 2-1 HOME Screen ................................................... 2-3 MENU Screen Displays .................................... 2-6 PROGRAM Menu Screen................................. 2-9 SELECT Menu Screen ...................................... 2-7 SPLASH Screen ................................................ 2-2 VIEW Menu Screen .......................................... 2-8 Getting to Know the Radio Controls and Indicators ..................................... 1-7 Equipment Characteristics ................................ 1-2 General Information .......................................... 1-1 Liberty Radio – Location of Controls and Indicators ...................................................... 1-4 Technical Characteristics .................................. 1-3 Glossary Acrynoms .......................................................... 7-1 Definitions ........................................................ 7-2 HOME Screen Context Area ..................................................... 2-4 SoftKeys Area ................................................... 2-5 Status Area ........................................................ 2-3 Indicators Connectors ...................................................... 1-12 LCD and Keypad Backlight ............................ 1-11 LED Indicators ................................................ 1-11 Maintenance External Battery Preventive Maintenance ......... 4-2 General Information .......................................... 4-1 Operational Checkout ....................................... 4-2 Radio Disassembly ........................................... 4-5 Radio Preventive Maintenance ......................... 4-2 Removal/Replacement Procedures - Operator .. 4-4 Troubleshooting ................................................ 4-3 Operating Instructions Changing ZONES ............................................. 3-9 Connecting the Antenna .................................... 3-1 Connecting the Battery ..................................... 3-1 General Information .......................................... 3-1 Menu Access ..................................................... 3-3 Modifying Menu Selections – SELECT Menu or PROGRAM Menu ........................................ 3-9 Operating Instructions ....................................... 3-1 P25 Unit to Unit Call ........................................ 3-5 Radio Programming .......................................... 3-1 Receiving .......................................................... 3-4 Scanning – Conventional and Priority .............. 3-6 Screensaver ..................................................... 3-10 Transmitting ...................................................... 3-4 Turning on the Radio ........................................ 3-2 Using the Pre-Programmed Side Buttons ......... 3-8 PROGRAM Menu Screen Channel Type – Analog Narrowband (AN) .... 2-12 Channel Type – Analog Wideband (AW) ....... 2-14 Channel Type - P25 .......................................... 2-9 MAINTENANCE Menu Screen ..................... 2-19 RADIO INFORMATION Menu Screen ......... 2-18 Radio Preventative Maintenace Inspection and Cleaning .................................... 4-2 Removal/Replacement Procedures - Operator Antenna Removal/Replacement ........................ 4-4 Audio Accessory Removal/Replacement .......... 4-4 Battery Removal/Replacement ......................... 4-5 Scanning - Conventional and Priority Enable SCAN .................................................... 3-6 Monitor Timer .................................................. 3-7 Priority Scan ..................................................... 3-6 Receiving a Voice Call on a Channel in the Scan List ............................................................... 3-7 SCAN Hold Timer ............................................ 3-7 Special ................................................................... 1-9
INDEX Index-2 Doc No.: 84382 Rev 2 THIS PAGE INTENTIONALLY LEFT BLANK
THALES COMMUNICATIONS, INC. 22605 GATEWAY CENTER DRIVE, CLARKSBURG, MD 20871 Toll-Free: 1.800.258.4420 Phone: 1.240.864.7000 Fax: 1.240.864.7920 www.thalesliberty.com and liberty@thalescomminc.com

Navigation menu