Tele Radio i Lysekil C1414A Transmitter User Manual

Tele Radio AB Transmitter

User manual

TELE RADIOPANTHERInstallation instructionsPN-RX-MN5 (PN-R8-1), PN-RX-MD11 (PN-R8-6), PN-RX-MN5E (PN-R8-10),PN-RX-MD11E (PN-R8-11), PN-TX-MD3M (PN-T13-3), PN-TX-MD6M (PN-T13-6),PN-TX-MD8M (PN-T13-8), PN-TX-MD10M (PN-T13-10), PN-TX-MD3 (PN-T21-3),PN-TX-MD6 (PN-T21-6), PN-TX-MD8 (PN-T21-8), PN-TX-MD10 (PN-T21-10),PN-TX-MN3 (PN-T7-16), PN-TX-MN6 (PN-T7-15), PN-TX-MN8 (PN-T7-14) Language: English (original)IM-PN-RX010-A04-EN
CONTENTSChapter 1: CUSTOMER INFORMATION 3Chapter 2: PRODUCT PAGES 5PN-RX-MN5, PN-RX-MN5E Base board receiver 5PN-RX-MD11, PN-RX-MD11E Base board receiver with a Relay expansion board 7PN-TX-MD, PN-TX-MDM, PN-TX-MN Transmitters 12Chapter 3: INSTALLERS GUIDE 15Default radio mode 15Start the transmitter 15Register the transmitter in the receiver 15Erase all transmitters from the receiver 16Turn the transmitter off 16Frequencies & channels 16Logout 17Make a Load selection 18Relay functionality 18Operating mode 1 19Chapter 4: BATTERY GUIDE 20Chapter 5: CERTIFICATIONS CHAPTER 22
Chapter 1: CUSTOMER INFORMATIONCHAPTER 1: CUSTOMER INFORMATIONTHANK YOU FOR PURCHASING A TELE RADIO AB PRODUCTREADALLINSTRUCTIONS ANDWARNINGS CAREFULLY BEFOREMOUNTING, INSTALLING ANDCONFIGURATING THEPRODUCTS.These instructions are published by Tele Radio AB without any guarantee. The instructions may be removed or revised by Tele Radio AB at any time and without further notice. Corrections and additions will be added to the latest version of the instruction.IMPORTANT! These instructions are directed to installers. There are separate instructions directed towards end users. The instructions that contain information on the installation and configuration of the radio remote control unit on the machine are not intended to be passed on to the end user. Only such information may be passed on to the end user that is needed to operate the machine correctly by radio remote control.Tele Radio AB products are covered by a guarantee/ warranty against material, construction or manufacturing faults. During the guarantee/ warranty period, Tele Radio AB may replace the product or faulty parts with new. Work under guarantee/ warranty must be carried out by Tele Radio AB or by an authorized service center specified by Tele Radio AB. Contact your Tele Radio AB representative if you need support or service.©Tele Radio ABDatavägen 21SE-436 32 ASKIMSWEDENTel: +46-31-748 54 60Fax: +46-31-68 54 64www.tele-radio.com-3-
Chapter 1: CUSTOMER INFORMATIONWARNINGS & RESTRICTIONSWARNING! Tele Radio remote controls are often built into wider applications. We recommend that the system is provided with a wired emergency stop where necessary.INSTALLING, CONNECTING AND MOUNTINGnAllow only licensed or qualified personnel to install the product.nSwitch the power supply off to the receiver before connecting the equipment.nCheck that you have connected the power supply to the correct connection terminal.nTo utilize the safety of the system, use the stop relays in the safety circuitry of the object that you want to control.nUse undamaged cables. No cables should hang loose.nAvoid installing in areas affected by strong vibrations.nPlace the receiver well away from wind, damp and water.nCable glands and vent plugs must face down to prevent water from seeping in.THE USERnMake sure that the user is following the instructions.nMake sure that the user has reached the certified age of your country to operate the equipment.nMake sure that the user is not under the influence of drugs, alcohol and medicines.nAllow only qualified personnel to have access to the transmitter and operate the equipment.nMake sure that the user does not leave the transmitter unsupervised.nMake sure that the user always turns the transmitter off when not in use.nMake sure that the user keeps a good overview of the work area.MAINTENANCEnUse the stop button to start and turn off the transmitter as often as possible.nWhen error messages are shown, it is very important to find out what caused them.nIf the stop button is mechanically damaged, contact your representative for service immediately.nAlways contact your representative for service and maintenance work on the product.nWrite down the serial numbers/ ID codes of the receivers and transmitters used. This inform-ation should be recorded on the “Settings document” for your product (download from our web-site).nAvoid registering transmitters to receivers where it is not being used.nKeep the safety instruction for future reference. Always download the configurations instruction from our web site for the latest version available.-4-
Chapter 2: PRODUCT PAGESCHAPTER 2: PRODUCT PAGES PN-RX-MN5, PN-RX-MN5E BASE BOARD RECEIVERWARNING! The receiver must NOT be opened by any other than a qualified installer. Make sure to turn the electricity off before opening the receiver.Base board:CO NO NC CO NO NC CO NO NC CO NO NC CO NO NC5 1 2 3 41 2 3 4 5136 7 8 9 10 11 12 14 15 16 17LEDs5 1 2 3 4LED7LED10LED8LED9LED6R5 R1 R2 R3 R412345678912-24V DC+ -1. Function relays 1-5 6. Function button (cancel)2. Function relay LEDs 1-5 (red) 7. Select button (OK) 3. Power LED (yellow) 8. Function LEDs (7=red, 8=yellow, 9=green, 10=orange)4. Radio module 9. Terminal block for input power 5. Programming connector TERMINAL BLOCK FOR INPUT POWER ON BASE BOARD1. 12 - 24V DC2. Negative terminal DC voltage-5-
FUNCTION LEDS INDICATION IN OPERATING MODEFunctionLED Off On Indicates7 (red)x  No transmitter is registered. x Flashes once: One or more transmitters are registered. No radio transmission established. x Double flash: One or more transmitters are registered and logged in. No radio transmission established. x Radio transmission established.8 (yellow)  x Receiving a radio packet from a transmitter other than a Panther.8 (yellow)9 (green)  x Receiving a radio packet from a transmitter set to the radio mode different from that of a receiver.8 (yellow)10 (orange)  x Receiving a radio packet from a transmitter that is not registered.9 (green)  x Receiving a radio packet, low signal (RSSI).10 (orange)  x Receiving a radio packet, configuration ID not accepted.9 (green)10 (orange)  x Receiving a radio packet, custom ID not accepted.8 (yellow)9 (green)10 (orange) x1. Receiving a radio packet from a registered transmitter. The receiver is already controlled by another registered transmitter. NOTE! "Radio link" must be activated in the receiver.2. Load select mode is activated. Incorrect Load is selected on the transmitter.-6-
PN-RX-MD11, PN-RX-MD11E BASE BOARD RECEIVER WITH A RELAY EXPANSION BOARDWARNING! The receiver must NOT be opened by any other than a qualified installer. Make sure to turn the electricity off before opening the receiver.Base board:1. Function relays 1-5 6. Function button (cancel)2. Relay LEDs 1-5 (red) 7. Select button (OK) 3. Power LED (yellow) 8. Function LEDs (7=red, 8=yellow, 9=green, 10=orange)4. Radio module 9. Terminal block for input power5. Programming connector -7-
Relay expansion board: 10. Function relays 6-11 12. Communication LED (green)11. Relay LEDs 6-11 (red) 13. Programming connectorTERMINAL BLOCK FOR INPUT POWER ON BASE BOARD1. 12 - 24V DC2. Negative terminal DC voltageTERMINAL BLOCK FOR INPUT POWER ON HIGH VOLTAGE EXPANSION BOARD21. Common 23. 24-110V AC22. Common 24. 230V AC-8-
FUNCTION LEDS INDICATION IN OPERATING MODEFunctionLED Off On Indicates7 (red)x  No transmitter is registered. x Flashes once: One or more transmitters are registered. No radio transmission established. x Double flash: One or more transmitters are registered and logged in. No radio transmission established. x Radio transmission established.8 (yellow)  x Receiving a radio packet from a transmitter other than a Panther.8 (yellow)9 (green)  x Receiving a radio packet from a transmitter set to the radio mode different from that of a receiver.8 (yellow)10 (orange)  x Receiving a radio packet from a transmitter that is not registered.9 (green)  x Receiving a radio packet, low signal (RSSI).10 (orange)  x Receiving a radio packet, configuration ID not accepted.9 (green)10 (orange)  x Receiving a radio packet, custom ID not accepted.8 (yellow)9 (green)10 (orange) x1. Receiving a radio packet from a registered transmitter. The receiver is already controlled by another registered transmitter. NOTE! "Radio link" must be activated in the receiver.2. Load select mode is activated. Incorrect Load is selected on the transmitter.TECHNICAL DATANumber of function relaysPN-RX-MN5, PN-RX-MN5E: 5 PN-RX-MD11, PN-RX-MD11E: 11 (potential free*, 10A, 250V AC)Input power 12-24V DCDigital inputs 8Duplex communication NoMax. number of registered transmitters 8IP class 66Size 120 x 117 x 51 mm / 4.7 x 4.6 x 2 inWeight 400 g / 0.8 lbs Operating temperature -20 - +55 °C / -4 - +130 °FOperating frequency 2405-2480 MHzNumber of channels 16 (channel 11-26)Channel separation 5 MHzAntennaPN-RX-MN5, PN-RX-MD11: 1 internal PCB antennaPN-RX-MN5E, PN-RX-MD11E: 1 external antenna, reversed SMA*potential free means that you have to supply voltage to get voltage out of a relay-9-
CURRENT CONSUMPTIONInput power Min.* Max.**12V DC 0.02A 0.3A24V DC 0.02A 0.2A24V AC 0.02A 0.2A48V AC 0.01A 0.05A110V AC 0.005A 0.03A230V AC 0.01A 0.02A*Minimum current consumption= Receiver powered, no radio session established, nothing else activated on the receiver.**Maximum current consumption= All relays activated on the receiver.ANTENNA - MOUNTING DESCRIPTIONNOTE! For optimum performance: Place well away from metal objects, such as metal girders, high-voltage cables and other antennas.lAntenna with cable - cable makes it possible for the antenna to be positioned freely and high above the ground.lAntenna without cable - if the receiver is installed on a wall, the antenna should be angled out from the wall.-10 -
RECEIVER MEASUREMENTS120.5 mm. (4.744 in.)102 mm. (4.016 in.)116.3 mm. (4.578 in.)90.4 mm. (3.559 in.)104 mm. (4.094 in.)Ø5 mm. (0.197 in.)51 mm. (2.007 in.)-11 -
PN-TX-MD, PN-TX-MDM, PN-TX-MN TRANSMITTERSPN-TX-MD PN-TX-MDM PN-TX-MN1. LED 1 (red) 1. LED 1 (red) 1. LED 1 (red)2. LED 2 (red) 2. Top LED (red, green) 2. Top LED (red, green)3. Top LED (red, green) 3. LED 2 (red) 3. LED 2 (red)4. LED 3 (red) 4. Buttons (1-10) 4. Buttons (1-8)5. LED 4 (red)  6. Buttons (1-10)  -12 -
TRANSMITTER BACKSIDE PN-TX-MD PN-TX-MDM PN-TX-MN1. On/Off switch 1. On/off switch 1. On/off switch2. Clip 2. Clip 2. Clip3. CE/FCC/IC label 3. CE/FCC/IC label 3. CE/FCC/IC labelON/OFF SWITCHThe transmitter has an on/off switch on the backside. The switch breaks the power supply from the battery. When in position 0/off, the transmitter cannot be started unless you connect the charger plug. When the transmitter is transported by airplane, the on/off switch must be in 0/off position. The switch should not be used as an on/off button for the transmitter.-13 -
TECHNICAL DATANO. OFBUTTONS PN-TX-MD3, PN-TX-MD3M, PN-TX-MN3 3 x 1-step buttonPN-TX-MD6, PN-TX-MD6M, PN-TX-MN6 6 x 1-step buttonPN-TX-MD8, PN-TX-MD8M, PN-TX-MN8 8 x 1-step buttonPN-TX-MD10, PN-TX-MD10M 10 x 1-step buttonBATTERY PN-TX-MD 3 x 1.5V AAAPN-TX-MDM, PN-TX-MN 2 x 1.5V AAAON/OFF SWITCH PN-TX-MD, PN-TX-MDM, PN-TX-MN YesDUPLEX COMMUNICATION PN-TX-MD, PN-TX-MDM, PN-TX-MN NoANTENNA PN-TX-MD, PN-TX-MDM, PN-TX-MN 1 internal PCB antennaSIZE PN-TX-MD 66 x 114 x 37.5 mm / 2.6 x 4.5 x 1.5 inPN-TX-MDM 66 x 114 x 37.5 mm / 2.6 x 4.5 x 1.5 inPN-TX-MN 52 x 83 x 17 mm / 2 x 3.3 x 0.7 inWEIGHT PN-TX-MD 135 g (0.29 lbs)PN-TX-MDM 135 g (0.29 lbs)PN-TX-MN 70 g (0.15 lbs)OPERATING FREQUENCY PN-TX-MD, PN-TX-MDM, PN-TX-MN 2.4 GHzNO. OF CHANNELS PN-TX-MD, PN-TX-MDM, PN-TX-MN 16 (channel 11-26)CHANNEL SEPARATION PN-TX-MD, PN-TX-MDM, PN-TX-MN 5 MHzIP CLASS PN-TX-MD, PN-TX-MDM 67PN-TX-MN 65OPERATING TEMPERATURE PN-TX-MD, PN-TX-MDM, PN-TX-MN -20 - +55 °C / -4 - +130 °F-14 -
Chapter 3: INSTALLERS GUIDECHAPTER 3: INSTALLERS GUIDEDEFAULT RADIO MODEThe transmitter is set to discontinuous radio mode by default. To establish a radio link between the transmitter and the receiver, both need to be in the same radio mode.The transmitter will start transmitting as soon as the batteries are inserted and any transmitter button is pressed. Radio transmission will end when all transmitter buttons are released.Note that some settings can only be made when the products are transmitting continuously. Those sections are marked with the text: "Only for continuous radio mode".To switch to continuous radio mode, the PC-program Settings Manager must be used. Please contact your representative for assistance.START THE TRANSMITTER1. Start the transmitter by pressing any button on the transmitter.REGISTER THE TRANSMITTER IN THE RECEIVERWARNING! Keep only transmitters, that you intend to use, registered in the receivers.1. Press the Function button on the receiver. Function LED lights red.2. Press the Select button on the receiver. All relay LEDs light red.3. Press button 1 and 2 on the transmitter. Keep pressed. All relay LEDs light red.4. Relay LEDs flash 2 times. 5. Release transmitter buttons 1 and 2.The relay LEDs flash 1 time. The transmitter is registered.-15 -
Chapter 3: INSTALLERS GUIDEERASE ALL TRANSMITTERS FROM THE RECEIVER1. Press the Function button on the receiver. Function LED lights red.2. Press the Select button on the receiver. All relay LEDs light red.3. All relay LEDs go out.4. Release the Select button.All transmitters are erased from the receiver.If the red function LED flashes, one or more transmitters are still registered in the receiver.TURN THE TRANSMITTER OFF1. The transmitter turns off when no transmitter button is pressed.FREQUENCIES & CHANNELSChannel Frequency11 240512 241013 241514 242015 242516 243017 243518 244019 244520 245021 245522 246023 246524 247025 247526 2480-16 -
Chapter 3: INSTALLERS GUIDESwitch channelNOTE! Only for the PN-TX-MD and when in continuous radio mode.1. Start the transmitter. The top LED flashes green.2. Press the Off-button on the transmitter. Keep pressed. The top LED flashes red.3. Within 2 seconds, press and hold button 1 or button 3 to switch channel.Button 1 = +1Button 3 = -1Top LED lights green. The channel is changed. The channel number is indicated by LED 1 and LED 4.Ex. channel 26: LED 1 flashes 2 times, LED 4 flashes 6 times.4. The transmitter switches off.LOGOUTNOTE! Only for the PN-TX-MD and when in continuous radio mode. NOTE! Logout function is deactivated by default. Contact your representative for assistance. Logout from the receiver1. Press the receiver Select button. LED 10 (orange) lights.2. Keep pressed (at least 4 seconds). LED 10 (orange) goes off.3. The transmitter is now logged off. Any other registered transmitter can be logged in.Quick logoutThere are two alternatives for logging out from the transmitter.Alternative 1:1. Press the Logout-button on the transmitter. Keep pressed.2. Press the Off-button. The top LED lights red.3. The transmitter switches off after logging out.Alternative 2:1. Press the Off-button. Keep pressed.2. Within 2 seconds, press the Logout-button. The top LED lights red. 3. The transmitter switches off after logging out.-17 -
Chapter 3: INSTALLERS GUIDE AUTOMATIC SHUTDOWNNOTE! You can not change the automatic shutdown time from the transmitter. Contact your representative for assistance.The transmitter automatic shutdown time is set to 3 minutes by default.MAKE A LOAD SELECTIONLoad select mode for the transmitter PN-TX-MDM, PN-TX-MN and PN-TX-MD is deactivated by default (Load select mode 0).NOTE! The loads are selected in the PC program Settings Manager. Contact your representative for assistance.RELAY FUNCTIONALITYNOTE! If Operating mode 0 is selected, you can not make these settings. Contact your representative for assistance.NOTE! Momentary relay functionality is default. That means that the relay will only be activated when you press a button on the transmitter. When the button is released, the relay deactivates. Setting a relay to latching means that the relay gets activated every time that you press a button, but in this case the relay remains active until the button is pressed again. NOTE! The settings options depend on the selected Operating mode. Momentary or latching relay functionality1. Press the receiver Function button 2 times. LED 8 (yellow) lights. The relay LEDs light.2. Press the receiver Select button to switch relay functionality. The relay LEDs flash to indicate that a latching or momentary functionality can be set to the corresponding relays.3. Press the receiver Function button to set latching or momentary functionality:LED 8 (yellow) off = momentary relay functionalityLED 8 (yellow) on = latching relay functionality4. Press the receiver Select button to step to the next available relay. When you have stepped through all the available relays, the receiver exits the settings menu.-18 -
OPERATING MODE 1 Button functionsOn relay -Working relay Relay 11 is active when relay 1-10 is activeRecommended Load Selection mode 0Programmable settings Relay 1-10 can be set latchingInterlocking -Radio mode DiscontinuousZero position check --19 -
Chapter 4: BATTERY GUIDECHAPTER 4: BATTERY GUIDEBATTERY INFORMATIONWARNING! Do not recharge the batteries. Attempts to recharge may cause rupture or the leaking of hazardous liquids, which will corrode the equipment.NOTE! Electronics and batteries must be physically separated before disposal. Make sure that electronics or batteries are not thrown in the household waste.Switch batteriesPN-TX-MDBattery type: 3 x 1.5V AAA / LR03 Alkaline1. Take off the transmitter backside by unscrewing the 5 screws.2. Switch the 3 x 1.5V AAA batteries. Use alkaline for optimal performance.3. Put the transmitter backside on againusing the screwdriver.PN-TX-MDMBattery type: 2 x 1.5V AAA / LR03 Alkaline++--1. Take off the transmitter backside by unscrewing the 5 screws.2. Switch the 2 x 1.5V AAA batteries. Use alkaline for optimal performance.3. Put the transmitter backside on againusing the screwdriver.PN-TX-MNBattery type: 2 x 1.5V AAA / LR03 Alkaline1. Take off the transmitter backside by unscrewing the 3 screws.2. Switch the 2 x 1.5V AAA batteries. Use alkaline for optimal performance.3. Put the transmitter backside on againusing the screwdriver.-20 -
BATTERY PRECAUTIONSObserve the following general battery warnings:nAs batteries contains flammable substances such as lithium or other organic solvents, they may cause heating, rupture or ignition.nRisk of explosion if battery is replaced with a battery of an incorrect type.nDo not short circuit, disassemble, deform or heat batteries.nNever try to charge a visibly damaged or frozen battery.nKeep batteries out of reach of small children. Should a child swallow a battery, consult a phys-ician immediately.nAvoid direct soldering to batteries.nWhen discarding batteries, insulate the + and - terminals of batteries with insulating/ masking tape. Do not put multiple batteries in the same plastic bag.nWhen improperly disposed, batteries may short circuit, causing them to become hot, burst or ignite.nStore in a cool location. Keep batteries away from direct sunlight, high temperature, and high humidity.nDo not throw batteries into fire.ROHS AND WEEEIn accordance with Directive 2011/65/EU on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS) and Directive 2012/19/EU on waste electrical and electronic equipment (WEEE), Tele Radio AB strives to minimize the use of hazardous materials, promotes reuse and recycling, and reduces emissions to air, soil and water. When a commercially viable alternative is available, Tele Radio AB strives to restrict or eliminate substances and materials that pose an environmental, health or safety risk.GUARANTEE, SERVICE, REPAIRS AND MAINTENANCEThe Tele Radio AB products are covered by a guarantee/warranty against material, construction and manufacturing faults. During the guarantee/warranty period, Tele Radio AB may replace the product or faulty parts. Work under guarantee/warranty must be carried out by Tele Radio AB or by an authorized service centre specified by Tele Radio AB.This is not covered by the guarantee/ warranty:nFaults resulting from normal wear and tearnParts of a consumable naturenProducts that have been subject to unauthorized modificationsnFaults resulting from incorrect installation and usenDamp and water damageMaintenance:nRepairs and maintenance must be carried out by qualified personnelnUse spare parts from Tele Radio AB onlynContact your representative if you require service or other assistancenKeep the product in a dry, clean placenKeep contacts and antennas cleannWipe off dust using a slightly damp, clean clothWARNING! Never use cleaning solutions or high-pressure water.-21 -
Chapter 5: CERTIFICATIONS CHAPTERCHAPTER 5: CERTIFICATIONS CHAPTERFCC STATEMENTStatement for warning:Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.This device complies with Industry Canada licence-exempt RSS standard(s) and Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence et la partie 15 des Règles FCC. L'exploitation est autorisée aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Cet appareil est conforme aux limites d’exposition au rayonnement RF stipulées par la FCC et l’IC pour une utilisation dans un environnement non contrôlé. L'utilisateur final doit suivre les instructions de fonctionnement spécifiques pour le respect d'exposition aux RF. Lesémetteurs ne doivent pas être placées près d’autres antennes ou émetteurs ou fonctionner avec ceux-ci.Note: this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—reorient or relocate the receiving antenna.—increase the separation between the equipment and receiver.—connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—consult the dealer or an experienced radio/TV technician for help.-22 -
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, th antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.FCC/IC LABEL ON THE TRANSMITTERPN-TX-MD PN-TX-MDM PN-TX-MN-23 -
EC/EEA DECLARATION OF CONFORMITY-24 -
-25 -
-26 -
(THISPAGEISINTENTIONALLYLEFTBLANK)-27 -


Navigation menu