Technology Solutions 1059 Multi ISO RFID Reader User Manual

Technology Solutions (UK) Ltd Multi ISO RFID Reader

User Manual

Multi ISO RFID 1059 User Guide.docMulti ISO RFID 1059 User GuideTechnology Solutions UK Ltd Suite CLoughborough Technology CentreEpinal WayLoughboroughLeicsLE11 3GETel: +44 (0) 1509 238248Fax: +44 (0) 1509 220020Email: enquiries@tsl.uk.com
Multi ISO RFID 1059 User Guide.doc 1059Page 2 of 22© 2006 TSL. All rights reserved.No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Technology Solutions (UK) Ltd. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.Technology Solutions (UK) Ltd (TSL) reserves the right to make changes to any product to improve reliability, function, or design. TSL does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which TSL products might be used. An implied license exists only for equipment, circuits, and subsystems contained in TSL products. TSL and the TSL logo are registered trademarks of TSL. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.All software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. TSL grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of TSL. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a licensed program in a network without written permission from TSL. The user agrees to maintain TSL’s copyright notice on the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof.TSL reserves the right to make changes to any software or product to improve reliability, function, or design.TSL does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.Symbol is a registered trademark of Symbol Technologies, Inc.
Multi ISO RFID 1059 User Guide.doc 1059Page 3 of 22Contents1 Introduction ...............................................................................................................................42 Parts of the RFID 1059 ............................................................................................................43 Attaching to an MC70...............................................................................................................54 Detaching from an MC70.........................................................................................................65 Using the RFID 1059................................................................................................................75.1 Basic operation .................................................................................................................75.2 Software support for the RFID 1059................................................................................95.2.1 Low level command set ............................................................................................95.2.2 API..............................................................................................................................95.3 Power management with the RFID 1059........................................................................ 95.4 Fitting a SAM................................................................................................................... 105.5 Compatible peripherals .................................................................................................. 115.6 ActiveSync....................................................................................................................... 116 Troubleshooting and Maintenance........................................................................................ 126.1 Maintenance.................................................................................................................... 126.2 Troubleshooting .............................................................................................................. 127 Technical specifications......................................................................................................... 147.1 Summary of specifications............................................................................................. 147.2 Pin-outs ...........................................................................................................................177.3 Regulatory Information................................................................................................... 187.4 Statement of compliance................................................................................................ 198 Health and Safety Recommendations .................................................................................. 209 Waste Electrical and Electronic Equipment (WEEE)........................................................... 2110 Warranty.............................................................................................................................. 21HistoryVersion Date Modifications1.0 31/08/06 Document Creation1.1 1/11/06 Added FCC Compliance to Regulatory section
Multi ISO RFID 1059 User Guide.doc 1059Page 4 of 221 IntroductionTechnology Solutions’ Multi ISO RFID 1059 provides the Symbol MC70 with Radio Frequency Identification (RFID) functionality. The unit attaches as a snap on to the MC70. The mechanical design of the unit allows it to be quickly and easily removed, alternatively two screws may be used to make the installation semi-permanent. The unit is designed to retain compatibility with standard MC70 accessories such as desktop cradles and chargers.The RFID 1059 is powered from the MC70. It can be used with the majority of transponders operating at 13.56MHz, including ISO15693 and ISO 14443 compliant types.2 Parts of the RFID 1059Figure 1: The parts of the RFID 1059Latch locking screw holeLatch locking screw holeDocking connectorStatus LEDsMC70 mating connectorAntenna located behind label.
Multi ISO RFID 1059 User Guide.doc 1059Page 5 of 223 Attaching to an MC70Figure 2: Attaching to an MC70Spring Clip3. For semi-permanent installation fit M2×6mm pan head Pozidriv screws into the latch locking screw holes.1.Align the slots on the MC70 with the guides on the spring clips of the RFID 1059.2. Slide the RFID 1059 on to the MC70 ensuring the MC70 aligns with the MC70 mating connector on the RFID 1059. The spring clips will push out and then click in as the MC70 locks in place.
Multi ISO RFID 1059 User Guide.doc 1059Page 6 of 224 Detaching from an MC70Figure 3: Detaching from an MC701. Remove the latch locking screws if fitted.2.Squeeze the spring clips together by pressing on the latch locking screw holes.3.Slide the RFID 1059 off the MC70.
Multi ISO RFID 1059 User Guide.doc 1059Page 7 of 225 Using the RFID 10595.1 Basic operationRFID transponders can be read when they are in range of the antenna. The antenna is located behind the label on the front of the RFID 1059. The range at which a transponder can be read depends on the transponder type and size. Larger transponders can be read further away from the antenna. In many cases it will be possible to read transponders behind and to the side of the RFID 1059. For best performance the transponder must be orientated correctly with the antenna. In most cases this means that the transponder should be parallel to the RFID 1059 cover as shown below:Figure 4: Presenting a transponder to the RFID 1059There are no drivers required for the RFID 1059. The unit is automatically powered up when the serial port on the bottom of the MC70 (COM1) is opened.The default operating mode of the RFID 1059 as supplied from Technology Solutions is continuous polling for transponders with the unique identification number (UID) of any compatible transponder being sent out to the MC70 in Correct orientation; the transponder is parallel to the reader antenna and read range will be good.Incorrect orientation; the transponder is perpendicular to the reader antenna and read range will be poor.
Multi ISO RFID 1059 User Guide.doc 1059Page 8 of 22ASCII format (COM1, 19200 baud). In this default mode an easy way to display the data is to use a Terminal Emulation program, for example mToken from Choung Networks. A trial version is available from http://www.choung.net/mToken/Having installed mToken with ActiveSync connect to the reader as follows: Launch mToken.  Select “Direct Comm Port” from the “session” menu.  Select the COM1  Change the baud rate to “19200”. Data bits should be 8, stop bits should be 1, parity should be “None” and flow control should be “None”.  Click “Connect”The transponder UIDs are then displayed, prefixed by a letter identifying the transponder type as follows; 'M' for ISO14443A, 'Z' for ISO14443B, 'S' for SR176, 'V' for ISO15693.The status LEDs on the front of the RFID 1059 provide an indication of the operating status of the RFID 1059.LED colour StatusGreen flash The previous command was successfully received and processed by the reader.Red flash The previous command was not successfully processed by the reader.Note that custom configuration of the RFID 1059 may prevent it from operating as described above.
Multi ISO RFID 1059 User Guide.doc 1059Page 9 of 225.2 Software support for the RFID 1059To make full use of the functionality of the RFID 1059, a customised software application will be required. Technology Solutions support two approaches to this; direct communication with the reader using the low level command set or the use of an API to simplify application development. 5.2.1 Low level command setThe Low level command set supports two modes; ASCII and binary. ASCII mode is typically used for simple applications, for example collecting transponder unique identifiers (UIDs). The binary protocol is more suited where complex interaction with transponders is required, for example a Mifare ticketing or vending application.The command set format and content is described in the document ‘Multi ISO RFID 1059 Protocol.pdf’ which is available for download from the Technology Solutions website at http://www.tsl.uk.com/downloads.htm .5.2.2 APIAn API is provided for use with the RFID 1059. This can be downloaded from the Technology Solutions website at http://www.tsl.uk.com/downloads.htm .A document is provided as part of the .zip folder which introduces the API. The RFID API is provided with Microsoft style compiled HTML help (.chm) and an intelli-sense file for general reference to the API. A sample application is also provided which demonstrates the use of the API.5.3 Power management with the RFID 1059All power for the RFID 1059 is drawn from the MC70. Maximum operating time is therefore obtained by managing the operation of the RFID 1059 optimally.The RFID 1059 has two operating modes; continuous read mode and standby mode. The third mode is fully powered off. The reader is switched between the two operating modes by software commands, documented in the Low level command set. The reader is fully powered off when the COM port on the MC70 is closed.The recommended power saving method is to close the serial port when the reader is not being used. The current consumption in Standby mode is high enough to reduce the MC70 battery life and the time taken to exit Standby mode is not much shorter than that from the serial port being opened. Any application using the RFID 1059 should therefore only open the COM port when an RFID transaction is to be performed.
Multi ISO RFID 1059 User Guide.doc 1059Page 10 of 225.4 Fitting a SAMTo fit a SAM it is necessary to remove the cover of the RFID 1059. This must only be done in an ESD safe area with appropriate precautions to avoid the possibility of damage to the RFID 1059.Remove the four Pozidriv screws securing the front cover:Figure 5: Location of cover fixing screwsRemove the front cover by pulling it away from the body of the RFID 1059, starting at the docking connector end.The SAM socket is unlocked by sliding the metal cover towards the MC70 mating connector:Figure 6: Unlocking the SAM socketRemove four screws.
Multi ISO RFID 1059 User Guide.doc 1059Page 11 of 22Slide in the SAM, making sure that it is orientated correctly and then relock the SAM socket by sliding the metal cover back away from the MC70 mating connector:Figure 7: Inserting the SAMReassemble the RFID 1059 by refitting the cover and securing it with the four screws.5.5 Compatible peripheralsThe HF RFID 1059 is compatible with any standard Symbol peripheral that does not use the serial port (COM1) because this is used for RFID data. The serial port is not connected to the Docking Connector on the bottom of the HF RFID 1059. A list of compatible peripherals for the HF RFID 1059 is available for download from the Technology Solutions website at http://www.tsl.uk.com/downloads.htm .It is not possible to use the HF RFID 1059 with the vehicle cradle (part number VCD7000-P000R). To charge the MC70 in a vehicle it is necessary to remove the HF RFID 1059 from the MC70 or to use the Auto charge cable (part number 25-70979-01).5.6 ActiveSyncThe MC70 with HF RFID 1059 attached can be used with ActiveSync, but the USB rather than the serial connection must be used.Note orientation of SAM.
Multi ISO RFID 1059 User Guide.doc 1059Page 12 of 226 Troubleshooting and Maintenance6.1 MaintenanceFor trouble-free service treat the RFID 1059 in the same way as you would the MC70 and observe the following tips when using the RFID 1059: Do not store or use the RFID 1059 in any location that is dusty, damp, or wet. Protect the RFID 1059 from temperature extremes. Do not leave it on the dashboard of a car on a hot day, and keep it away from heat sources.6.2 TroubleshootingSymptoms Possible Cause ActionThe Application on the MC70 cannot communicate with the RFID 1059.The MC70 is not firmly seated into the RFID1059.Remove and re-insert the MC70 from the RFID1059, ensuring it is firmly seated.The port has not been opened.Check that the Application has been configured to use COM1.The port is in use by another application.Close the other application and try again.The baud rate is set incorrectly in the application.Check that the application is set to 19200 baud, 8 data bits, no parity and one stop bit (settings may be different if the RFID 1059 has been reconfigured) .The RFID 1059 does not read a particular transponderThe RFID 1059 has been configured to exclude some transponder types.Refer to the command documentation to include the appropriate transponder type.The transponder is out of range of the RFID 1059.Move the transponder closer to the antenna.MC70 battery does not chargeThe battery is faulty. Verify that other batteries charge properly. If so, replace
Multi ISO RFID 1059 User Guide.doc 1059Page 13 of 22Symptoms Possible Cause Actionthe faulty battery.Ambient temperature is too warm.Move the unit to an area where the ambient temperature is between 0°C and 35°C.The MC70 is not firmly seated into the RFID 1059.Remove and re-insert the MC70 from the RFID 1059, ensuring it is firmly seated.ActiveSync cannot connect to the MC70ActiveSync is not correctly configured on the PC or the MC70.Detach the RFID 1059from the MC70 and try to ActiveSync directly to the MC70. If this does not work then consult the MC70 User Guide.ActiveSync is using a serial connection.ActiveSync must use USB with the RFID 1059connected.The MC70 is not firmly seated into the RFID 1059.Remove and re-insert the MC70 from the RFID 1059, ensuring it isfirmly seated.An accessory connected to the RFID 1059 does not workThe accessory uses a serial connection to the MC70.The accessory is not compatible with the RFID 1059 because only the USB port is available on the docking connector.The MC70 is not firmly seated into the RFID 1059.Remove and re-insert the MC70 from the RFID 1059, ensuring it is firmly seated.
Multi ISO RFID 1059 User Guide.doc 1059Page 14 of 227 Technical specifications7.1 Summary of specificationsThe following table summarises the RFID 1059’s intended operating environment and technical hardware specifications:Performance Characteristics RF Transmit Frequency 13.56MHz Supported RFID Standards ISO14443A, ISO14443B, ISO 15693, ISO 18000-3, ICODETag-it HF-I SR176 Tag-it HF-I Light S SRIX4K Philips ICODE SL2 LRI 12Infineon ISO15693 LRI 64MIFARE® StandardLRI 512MIFARE® 4k EM4135MIFARE® Pro KSW Temp SenseMIFARE® Ultralight Sharp SMIFARE® DESFIRE ASK GTMLMIFARE® SmartMX ASK GTML2ISOSLE 55Rxx TOSMART P064SRF55VxxP +S Jewel Tag (IRT0302B11 KSW)SLE 66CL160S ISO14443A Tags SLE 66CLX320P ISO14443B Tags Supported Tag-ICs ISO15693 Tags Reading distance Up to 8cm (3") using ISO7810 size credit card format transponders. RF Transmission Speed Up to 848 kBit/s SAM supportSAM clock 3.39MHz
Multi ISO RFID 1059 User Guide.doc 1059Page 15 of 22SAM VCC 5VSAM type Form factor compatible with GSM SIM footprintCurrent consumption< 150mA during RFID read< 30mA in standby mode Current Consumption 0mA in shutdown modeUser indicationRed, Green LEDs Flash indicating activity (function may also be customised).Connection InterfacesPhysical interface USB and power in to charge MC70Reader power supply Powered from host terminalActiveSync via USBPhysical CharacteristicsDimensions 90×82×32mm (3.54"x3.23"x1.26")Weight 95g (3.35 oz)Enclosure material PC/ABSColour GreyMaterial finish Sparked surfaceMechanical attachment Snap-on action with optional locking screwsDocking Attachment maintains dockability with Symbol docking cradle for charging and ActiveSyncEnvironmentalOperating Temperature -10°C to +50°C (14°F to 122°F)Storage Temperature -40°C to +60°C (-40°F to 140°F)Humidity Up to 90% Relative humidity Non CondensingDrop specification 1.3m (4.26ft) to concrete, 6 drops per 6 sides over operating temperature; 1.5m (5ft) to concrete, 2 drops per 6 sides at ambient temperature 23ºC (73ºF)Sealing Internal components conformal coatedElectrostatic discharge +/-15kV air discharge, +/-8kV direct
Multi ISO RFID 1059 User Guide.doc 1059Page 16 of 22dischargeConstruction RoHS compliantRegulatoryEN 300 330, EN 301 489, CE markedEMI/RFIUSA - FCC Part 15Europe - EN60950-1Electrical SafetyUSA - UL60950NotesAll PCBs are conformally coated
Multi ISO RFID 1059 User Guide.doc 1059Page 17 of 227.2 Pin-outsPIN Docking Connector (Socket)1 Power Ground2 Cradle Detect3 RS232 DCD/Trigger4 USB_D-5 USB_D+6 USB_Gnd7 USB_Vbus8 USB_ID9 Not Connected10 Not Connected11 Not Connected12 Not Connected13 Not Connected14 Not Connected15 Not Connected16 External DC In 5.4V
Multi ISO RFID 1059 User Guide.doc 1059Page 18 of 227.3 Regulatory InformationAll TSL devices are designed to be compliant with appropriate regulations and standards and are CE marked. Any changes or modifications to TSL equipment, not expressly approved by TSL, could void the user's authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Multi ISO RFID 1059 User Guide.doc 1059Page 19 of 227.4 Statement of complianceTechnology Solutions hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directives 1999/5/EC, 89/336/EEC and 73/23/EEC. Declaration of Conformities may be obtained from Technology Solutions on request.The RFID 1059 has been tested to and found to comply with the following standards for use within the Economic Union:EMC Directive 89/336/EEC, R&TTE Directive 99/5/EC:EN 301 489-3 V1.4.1 (2002-08)EN 300 330-2 V1.1.1 (2001-06)Low Voltage Directive 73/23/EEC:IEC 60950-1 1st Edition 2001 (National and group differences in accordance with CB Bulletin No. 109A December 2005)The RFID 1059 has also been tested and found to comply with:Title 47 of the CFR:2004, Part 15, Subpart (c)FCC emission requirements for Intentional Radiators; Parts 15.207, 15.209 & 15.225The RFID 1059 complies with:RoHS Directive 2002/95/EC
Multi ISO RFID 1059 User Guide.doc 1059Page 20 of 228 Health and Safety RecommendationsErgonomic RecommendationsCaution: In order to avoid or minimize the potential risk of ergonomic injury, follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury.• Reduce or eliminate repetitive motion• Maintain a natural position• Reduce or eliminate excessive force• Keep objects that are used frequently within easy reach• Perform tasks at correct heights• Reduce or eliminate vibration• Reduce or eliminate direct pressure• Provide adjustable workstations• Provide adequate clearance• Provide a suitable working environment• Improve work procedures.For vehicle installation and useAn air bag inflates with great force. DO NOT place objects, including either installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result.RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (including safety systems). Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle.Power SupplyUse only Symbol-approved cradles, chargers and power supplies with the HF RFID 1059. Use of an alternative power supply will invalidate any approval given to this device, void the warranty for the product and may be dangerous.
Multi ISO RFID 1059 User Guide.doc 1059Page 21 of 229 Waste Electrical and Electronic Equipment (WEEE)For EU Customers: All products at the end of their life must be returned to TSL for recycling. For information on how to return product please contact TSL.10 Warranty(A) Warranty TSL’s hardware Products are warranted against defects in workmanship and materials for a period of twelve (12) months from the date of shipment, unless otherwise provided by TSL in writing, provided the Product remains unmodified and is operated under normal and proper conditions. Warranty provisions and durations on software, integrated installed systems, Product modified or designed to meet specific customer specifications (“Custom Products”), remanufactured products, and reconditioned or upgraded products, shall be as provided in the applicable Product specification in effect at the time of purchase or in the accompanying software license.(B) Spare Parts Spare parts (i.e. parts, components, or subassemblies sold by TSL for use in the service and maintenance of Products) are warranted against defects in workmanship and materials for a period of thirty (30) days from the date of shipment. Spare parts may be new or originate from returned units under the conditions set forth in subsection D below.(C) Repair of TSL branded hardware For repairs on TSL branded hardware Products under this Agreement, including repairs covered by warranty, the repair services provided are warranted against defects in workmanship and materials on the repaired component of the Product for a period of thirty (30) days from the shipment date of the repaired Product, or until the end of the original warranty period, whichever is longer. Any such defects shall be notified to TSL in writing within 7 days of the same becoming apparent.(D) Product Service Products may be serviced or manufactured with parts, components, or subassemblies that originate from returned products and that have been tested as meeting applicable specifications for equivalent new material and Products. The sole obligation of TSL for defective hardware Products is limited to repair or replacement (at TSL’s option) on a “return to base (RTB)” basis with prior TSL authorisation.Customer is responsible for prompt shipment to TSL and assumes all costs and risks associated with this transportation; return shipment to the Customer will be at TSL's expense. Customer shall be responsible for return shipment charges for product returned where TSL determines there is no defect (“No Defect Found”), or for product returned that TSL determines is not eligible for warranty repair. No charge will be made to Buyer for replacement parts for warranty repairs. TSL is not responsible for any damage to or loss of any software programs, data or removable data storage media, or the restoration or reinstallation of any software programs or data other than the software, if any, installed by TSL during manufacture of the Product.
Multi ISO RFID 1059 User Guide.doc 1059Page 22 of 22(E) Original Warranty Period Except for the warranty applying solely to the repaired component arising from a repair service as provided in Section C above, the aforementioned provisions do not extend the original warranty period of any Product that had either been repaired or replaced by TSL.(F) Warranty Provisions The above warranty provisions shall not apply to any Product(i) which has been repaired, tampered with, altered or modified, except by TSL’s authorized service personnel; (ii) in which the defects or damage to the Product result from normal wear and tear, misuse, negligence, improper storage, water or other liquids, battery leakage, use of parts or accessories not approved or supplied by TSL, or failure to perform operator handling and scheduled maintenance instructions supplied by TSL;(iii) which has been subjected to unusual physical or electrical stress, abuse, or accident, or forces or exposure beyond normal use within the specified operational and environmental parameters set forth in the applicable Product specification; nor shall the above warranty provisions apply to any expendable or consumable items, such as batteries, supplied with the Product.EXCEPT FOR THE WARRANTY OF TITLE AND THE EXPRESS WARRANTIES STATED ABOVE, TSL DISCLAIMS ALL WARRANTIES ON PRODUCTS FURNISHED HEREUNDER INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE LIMITED WARRANTY PERIOD. SOME STATES OR COUNTRIES DO NOT ALLOW A LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR CONSUMER PRODUCTS. IN SUCH STATES OR COUNTRIES, FOR SUCH PRODUCTS, SOME EXCLUSIONS OR LIMITATIONS OF THIS LIMITED WARRANTY MAY NOT APPLY.The stated express warranties are in lieu of all obligations or liabilities on the part of TSL for damages, including but not limited to, special, indirect or consequential damages arising out of or in connection with the use or performance of the Product or service. TSL’s liability for damages to Buyer or others resulting from the use of any Product or service furnished hereunder shall in no way exceed the purchase price of said Product or the fair market value of said service, except in instances of injury to persons or property.TSL is not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty. If the original shipping container was not kept, contact your local distributor or TSL to have another sent to you.TSL shall not be responsible for any injury, damage or loss of whatever kind caused directly or indirectly by the goods whether as a result of their manufacture, operation, use or otherwise and the customer shall indemnify TSL from any claim arising from any loss suffered by any third party.

Navigation menu