Technicolor Delivery Technologies Belgium TG789VNV3 WLAN Access Point TG789vn v3, TG788vn, TG589vn v2 User Manual TG789vn v3 SetupUserGuide en

Technicolor Delivery Technologies Belgium WLAN Access Point TG789vn v3, TG788vn, TG589vn v2 TG789vn v3 SetupUserGuide en

Contents

User Manual

SETUP AND USER GUIDETechnicolor TG789vn v3
SETUP AND USER GUIDETechnicolor TG789vn v3
CopyrightCopyright ©1999-2011 Technicolor. All rights reserved. Distribution and copying of this document, use and communication of its contents is not permitted without written authorization from Technicolor. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by Technicolor. Technicolor assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.Technicolor Delivery Technologies Belgium NVPrins Boudewijnlaan, 47 2650 Edegem Belgium http://www.technicolor.comTrademarksThe following trademarks may be used in this document:DECT™ is a trademark of ETSI.Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.Ethernet™ is a trademark of Xerox Corporation.Wi-Fi®, WMM® and the Wi-Fi logo are registered trademarks of the Wi-Fi Alliance®. Wi-Fi CERTIFIED, Wi-Fi ZONE, Wi-Fi Protected Access, Wi-Fi Multimedia, Wi-Fi Protected Setup, WPA, WPA2 and their respective logos are trademarks of the Wi-Fi Alli-ance®.UPnP™ is a certification mark of the UPnP™ Implementers Corporation.DLNA® is a registered trademark, DLNA disc logo is a service mark, and DLNA Certified is a trademark of the Digital Living Network Alliance. Digital Living Network Alliance is a service mark of the Digital Living Network Alliance.Microsoft®, MS-DOS®, Windows®, Windows NT® and Windows Vista® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.Apple® and Mac OS® are registered trademarks of Apple Computer, Incorporated, registered in the United States and other countries.UNIX® is a registered trademark of UNIX System Laboratories, Incorporated.Adobe®, the Adobe logo, Acrobat and Acrobat Reader are trademarks or registered trademarks of Adobe Systems, Incorporated, registered in the United States and/or other countries.Other brands and product names may be trademarks or registered trademarks of their respective holders. All other logos, trademarks and service marks are the property of their respective owners, where marked or not.Document InformationStatus: v0.1 (November 2011)Reference: DMS-CTC-20101206-0033Short Title: Setup and User Guide Technicolor TG789vn v3 R8.4.x
iCONTENTSDMS-CTC-20101206-0033 v0.11 Getting Started ......................................................................................................... 31.1 Features At A Glance............................................................................................................................... 41.2 User Scenarios ............................................................................................................................................51.3 Components .............................................................................................................................................. 61.3.1 Power ................................................................................................................................................................................71.3.2 Local Network Connection........................................................................................................................................... 81.3.3 Broadband Connection ................................................................................................................................................. 91.3.4 Voice Connection........................................................................................................................................................ 101.3.5 Buttons............................................................................................................................................................................ 111.3.6 Status LEDs ...................................................................................................................................................................121.4 Preparing for the Installation...................................................................................................................152 Guided Installation...................................................................................................173 Manual Installation...................................................................................................193.1 Connecting the Technicolor Gateway to your Service Provider’s Network.................................... 203.1.1 Setting up your Technicolor Gateway as DSL Gateway .........................................................................................213.1.2 Setting up your Technicolor Gateway as Local Router........................................................................................... 243.2 Powering on the Technicolor Gateway.................................................................................................253.3 Connecting Your Network Devices to the Technicolor Gateway.................................................... 263.3.1 Setting up a Wireless Connection...............................................................................................................................273.3.2 Setting up a Wired Connection.................................................................................................................................. 283.4 Configure the Technicolor Gateway.................................................................................................... 293.5 Setting Up the 3G Fall-Back WAN Connection................................................................................. 303.5.1 Managing your Mobile Connection with the Technicolor Gateway GUI .............................................................313.5.2 Inserting a Mobile USB Adapter.................................................................................................................................324 Configuration Tools.................................................................................................334.1 Technicolor Gateway GUI......................................................................................................................344.1.1 Access............................................................................................................................................................................ 354.1.2 Components ................................................................................................................................................................. 364.1.3 Protecting Access to the Technicolor Gateway....................................................................................................... 384.2 Backing Up/Restoring your Configuration...........................................................................................394.3 Access From the Internet....................................................................................................................... 405 The Technicolor Gateway Wireless Access Point...................................................415.1 Connecting Your Wireless Client via WPS ......................................................................................... 425.2 Connecting Your Wireless Client without WPS ................................................................................. 445.3 Securing Your Wireless Connection..................................................................................................... 456 Telephony................................................................................................................ 476.1 Setting Up Your Telephone Network .................................................................................................. 486.1.1 Connection to the Traditional Telephone Network................................................................................................ 496.1.2 Configuring the Technicolor Gateway VoIP Service..............................................................................................506.2 Address Book............................................................................................................................................52
iiCONTENTSDMS-CTC-20101206-0033 v0.16.3 Telephony Services................................................................................................................................. 546.3.1 Activating a Telephony Service on your Technicolor Gateway............................................................................. 556.3.2 Common Telephony Services .................................................................................................................................... 566.4 Viewing Call Logs ................................................................................................................................... 597 Saving Energy with Your Technicolor Gateway......................................................617.1 Code of Conduct.................................................................................................................................... 627.2 ECO Manager..........................................................................................................................................637.3 Manually Switching Off Services to Reduce Power ........................................................................... 648 Sharing Content on your Technicolor Gateway..................................................... 658.1 The Network File Server .........................................................................................................................678.2 The UPnP AV Media Server................................................................................................................. 708.2.1 Configuring the UPnP AV Media Server ..................................................................................................................718.2.2 Using the UPnP AV Media Server .............................................................................................................................728.3 The FTP Server....................................................................................................................................... 748.4 Managing your Shared Content.............................................................................................................768.5 Safely Removing your USB Storage Device.........................................................................................789 Technicolor Gateway Network Services................................................................. 799.1 UPnP.........................................................................................................................................................809.1.1 Accessing Your Technicolor Gateway via UPnP......................................................................................................819.1.2 Managing your Internet connection via UPnP ......................................................................................................... 829.1.3 Configuring UPnP on the Technicolor Gateway..................................................................................................... 849.1.4 Installing UPnP on Windows XP................................................................................................................................ 859.2 Assigning a service (HTTP, FTP,...) to a Computer...........................................................................879.3 Dynamic DNS ......................................................................................................................................... 8910 Internet Security.......................................................................................................9110.1 Parental Control ...................................................................................................................................... 9210.1.1 Configuring Content-based Filtering........................................................................................................................ 9410.1.2 Adding Rules for Address-Based Filtering................................................................................................................ 9510.2 Firewall ......................................................................................................................................................9711 Support.................................................................................................................... 9911.1 Setup Troubleshooting......................................................................................................................... 10011.2 General Technicolor Gateway Troubleshooting ............................................................................... 10111.3 Wired Connection Troubleshooting ...................................................................................................10211.4 Wireless Connection Troubleshooting................................................................................................10311.5 Voice over IP Troubleshooting ........................................................................................................... 10411.6 Reset to Factory Defaults .....................................................................................................................105
1ABOUT THIS SETUP AND USER GUIDEDMS-CTC-20101206-0033 v0.1About this Setup and User GuideIn this Setup and User GuideThe goal of this Setup and User Guide is to show you:Set up your Technicolor Gateway and local networkConfigure and use the main features of your Technicolor Gateway.For more advanced scenarios and features visit the documentation pages on www.technicolor.com.Used Symbols Te r m i n o l o g yGenerally, the Technicolor TG789vn v3 will be referred to as Technicolor Gateway in this Setup and User Guide.Typographical ConventionsFollowing typographical convention is used throughout this manual:This sample text indicates a hyperlink to a Web site.Example: For more information, visit us at www.technicolor.com.This sample text indicates an internal link.Example: If you want to know more about guide, see “About this Setup and User Guide” on page 1.This sample text indicates an important content-related word.Example: To enter the network, you must authenticate yourself.This sample text indicates a GUI element (commands on menus and buttons, dialog box elements, file names, paths and folders).Example: On the File menu, click Open to open a file.The danger symbol indicates that there may be a possibility of physical injury.The warning symbol indicates that there may be a possibility of equipment damage.The caution symbol indicates that there may be a possibility of service interruption.The note symbol indicates that the text provides additional information about a topic.
2ABOUT THIS SETUP AND USER GUIDEDMS-CTC-20101206-0033 v0.1
31 GETTING STARTEDDMS-CTC-20101206-0033 v0.11 Getting StartedIntroductionThis chapter gives you a brief overview of the main features and components of the Technicolor Gateway. After this chapter we will start with the installation. Do not connect any cables to the Technicolor Gateway until instructed to do so.
41 GETTING STARTEDDMS-CTC-20101206-0033 v0.11.1 Features At A GlanceIntroductionThis section provides a brief overview of the main features of your Technicolor Gateway.Internet connection featuresBroadband Internet access via the integrated DSL modem.The first chapters describe how to connect your Technicolor Gateway to the Internet.Broadband Internet access via the Gigabit WAN port.The first chapters describe how to connect your Technicolor Gateway to the Internet.3G (Fall-back) High-speed Internet Access via the optional mobile USB adaptor.For more information, see “3.5 Setting Up the 3G Fall-Back WAN Connection” on page 30.Internet Security for your entire network.For more information, see “10 Internet Security” on page 91.Useful network tools like UPnP, Dynamic DNS and many more.For more information, see “9 Technicolor Gateway Network Services” on page 79.Local networking featuresWired access for your local network devices via the Ethernet interface.For more information, see “3.3.2 Setting up a Wired Connection” on page 28.Wireless access for your local network devices via the integrated IEEE 802.11n wireless access point.For more information, see “5 The Technicolor Gateway Wireless Access Point” on page 41.An Integrated Media Server allowing you to share your media with media players and other network devices. For more information, see “8 Sharing Content on your Technicolor Gateway” on page 65.Telephony featuresThe Technicolor Gateway offers Voice over IP (VoIP) connectivity for traditional phones and IP phones.For more information see “6 Telephony” on page 47ECO labelTechnicolor’s ECO label guarantees you that the Technicolor Gateway is able to reduce its power consumption to an absolute minimum. For more information, see “7 Saving Energy with Your Technicolor Gateway” on page 61.Technicolor Gateway configuration toolsThe Technicolor Gateway Setup CD allows you to configure your Technicolor Gateway and helps you to connect your computers to the Technicolor Gateway.The Technicolor Gateway GUI allows you to configure your Technicolor Gateway via your web browser.For more information, see “4.1 Technicolor Gateway GUI” on page 34.
51 GETTING STARTEDDMS-CTC-20101206-0033 v0.11.2 User ScenariosScenariosDepending of the architecture of your home network, you can use the Technicolor Gateway in either of the following scenarios:DSL GatewayLocal RouterDSL GatewayThe Technicolor Gateway is connected to the DSL network of your service provider and brings the Internet to your home.Local RouterThe Technicolor Gateway is placed behind another gateway or modem. In this setup the gateway or modem in front of the Technicolor Gateway will establish the connection to the Internet:This scenario is used when:The Internet connectivity is provided by another device (for example, a cable modem). The Technicolor Gateway is used to add specific services to your home network.Your service provider is using Ethernet in the First Mile (EFM).The Ethernet signal is directly coming into your home.Your service provider is using Ethernet To The Home (ETTH).Technicolor Gateway is directly connected to the terminator of your service provider’s fiber-optic network and your local network InternetTechnicolor GatewayInternetModem/Router Technicolor Gateway
61 GETTING STARTEDDMS-CTC-20101206-0033 v0.11.3 ComponentsOverviewThis section provides an overview of the different components of the Technicolor Gateway:To p i c Page1.3.1 Power 71.3.2 Local Network Connection 81.3.3 Broadband Connection 91.3.4 Voice Connection 101.3.5 Buttons 111.3.6 Status LEDs 12
71 GETTING STARTEDDMS-CTC-20101206-0033 v0.11.3.1 PowerOverviewPower inletThe power inlet () allows you to connect the power supply.Power switchThe power switch () allows you to power on/off your Technicolor Gateway.Only use the power supply delivered with your Technicolor Gateway.
81 GETTING STARTEDDMS-CTC-20101206-0033 v0.11.3.2 Local Network ConnectionOverviewWireless Access PointThe built-in WiFi-certified wireless access point provides wireless access to your WiFi-certified wireless clients.For more information, see “5 The Technicolor Gateway Wireless Access Point” on page 41.Ethernet switchThe Ethernet switch () allows you to connect an Ethernet device (for example, a computer) to your local network. For more information, see “3.3.2 Setting up a Wired Connection” on page 28.A LED may be provided per Ethernet port to indicate link integrity (or activity).USB PortThe USB port () can be used to:Connect a USB mass storage device to share your content (for example, music, movies,...):On your local network via the Network File server or the UPnP AV Media Server.On Internet via FTP.For more information, see “8 Sharing Content on your Technicolor Gateway” on page 65.LED Status DescriptionSolid on Device connected.Blinking Device connected and sending/receiving data.Off No device connected.
91 GETTING STARTEDDMS-CTC-20101206-0033 v0.11.3.3 Broadband ConnectionOverviewDSL portThis port can be used to connect your Technicolor Gateway to your service provider’s DSL network.WAN portThis port allows you to use your Technicolor Gateway as Local Router. For more information, see “1.2 User Scenarios” on page 5.WANDSL
101 GETTING STARTEDDMS-CTC-20101206-0033 v0.11.3.4 Voice ConnectionOverviewPhone PortThe Phone ( ) port allows you to connect a traditional phone to your Technicolor Gateway. This way you will be able to make phone calls over the Internet and save on communication costs, especially for long-distance calls.For more information, see “6.1 Setting Up Your Telephone Network” on page 48.PSTN Port (optional)The PSTN port allows you to connect the Technicolor Gateway to the traditional telephone network, i.e. the Public Switched Telephone Network (PSTN). When the VoIP connection is not available, the Technicolor Gateway will automatically switch from VoIP to the traditional telephone network.For more information, see “6.1.1 Connection to the Traditional Telephone Network” on page 49.PSTNIf your Technicolor Gateway does not have a PSTN port, this means that:Your Technicolor Gateways has an integrated filterThe Technicolor Gateway separates the phone signal from the signal coming from the DSL port. Your Technicolor Gateway has an integrated filter if the product name printed on the label of your Technicolor Gateway ends with “wIF” (with Integrated Filter). If this suffix is not present, then your Technicolor Gateway does not have an integrated filter.- or -Your Technicolor Gateway is VoIP-onlyAll calls passing through the Technicolor Gateway will be done via VoIP.Be aware that, if you are not connected to the traditional telephone network, emergency calls will not be possible when your Internet connection is down or your Technicolor Gateway is powered off.
111 GETTING STARTEDDMS-CTC-20101206-0033 v0.11.3.5 ButtonsOverviewWPS buttonThe WPS ( ) button allows you to add new wireless clients to your network in a swift and easy way, without the need to enter any of your wireless settings manually.For more information, see “5.1 Connecting Your Wireless Client via WPS” on page 42.ECO buttonThe ECO ( ) button allows you to disable your wireless access point. You can do this when you do not have any devices that are connected to the wireless access point. This allows you to save the energy that the Technicolor Gateway would be using for the wireless access point. For more information, see “ECO button” on page 64.Reset buttonThe Reset button allows you to reset your Technicolor Gateway to factory defaults.For more information, see “11.6 Reset to Factory Defaults” on page 105.Reset
121 GETTING STARTEDDMS-CTC-20101206-0033 v0.11.3.6 Status LEDsIntroductionOn the front panel of your Technicolor Gateway, you can find a number of status LEDs, indicating the state of the device.Power LEDEthernet LEDUpgradePowerEthernetUSBWirelessVoiceBroadbandInternetTVWPSColour State DescriptionGreen Solid on Power on, normal operationBlinking Bootloader active (during upgrade)Red Solid on Power on, self-test failed, indicating device malfunctionOrange Solid on Bootloader selftestBlinking Bootloader active (during upgrade)Off The Technicolor Gateway is powered off.Colour State DescriptionGreen Solid on Network device connected to the Ethernet switch.Blinking Network device connected to the Ethernet switch and sending/receiving data.Off No Ethernet connection on your local network
131 GETTING STARTEDDMS-CTC-20101206-0033 v0.1USB LEDWireless LED Broadband LED (if you are using the DSL Gateway scenario)Broadband LED (if you are using the Local Router scenario)Internet LEDColour State DescriptionGreen Solid on Device(s) connected to the Technicolor Gateway’s USB portOff No device connected to the Technicolor Gateway’s USB portColour State DescriptionGreen Solid on No wireless activity, WPA(2) encryptionBlinking Wireless activity, WPA(2) encryptionOrange Solid on No wireless activity, WEP encryptionBlinking Wireless activity, WEP encryptionRed Solid on No wireless activity, no securityBlinking Wireless activity, no securityRed/green Toggling Wireless client registration phaseOff Wireless access point disabledColour State DescriptionGreen Solid on DSL line synchronisedBlinking Trying to detect carrier signal or pending DSL line synchronisationOff Technicolor Gateway powered off. Colour State DescriptionGreen Solid on Connected to the WAN deviceOff Not connected to the WAN deviceColour State DescriptionGreen Solid on Connected to the Internet, no activityBlinking Connected to the Internet, sending/receiving dataRed Solid on Failed to setup the Internet connectionOff No Internet connection
141 GETTING STARTEDDMS-CTC-20101206-0033 v0.1TV LEDPhone LEDUpgrade LEDWPS LEDFor more information about WPS, see “5.1 Connecting Your Wireless Client via WPS” on page 42.Colour State DescriptionGreen Solid on Set-Top Box (STB) connected to the Technicolor GatewayBlinking Unknown STB connected to the Technicolor GatewayOff No STB connected to the Technicolor GatewayColour State DescriptionGreen Solid on Registered at your VoIP provider, no activity.Blinking Registered at your VoIP provider, activity.Off Not registered to your VoIP provider.Colour State DescriptionBlue Solid on Software upgrade ongoingOff No software upgrade ongoingDo not power off your Technicolor Gateway or disconnect any cables as long as the Upgrade LED is on. Interrupting the upgrade procedure may damage your Technicolor Gateway.Colour State DescriptionGreen Solid On Client successfully registered via WPSOrange Blinking WPS registration ongoingRed Blinking Error occurred
151 GETTING STARTEDDMS-CTC-20101206-0033 v0.11.4 Preparing for the InstallationDSL service requirementsThis section is only applicable if you are using your Technicolor Gateway as DSL gateway. For more information, see “1.2 User Scenarios” on page 5.Make sure that:Your service provider activated the DSL service on your telephone line by your service provider.You have the installation information (for example, user name, password, service profile,...) provided by your service provider at hand.Local connection requirementsWireless connectionIf you want to connect your computer using a wireless connection, your computer must be equipped with a WiFi-certified wireless client adapter.Wired connectionIf you want to connect a computer using a wired connection, your computer must be equipped with an Ethernet Network Interface Card (NIC).Start with the installationYou are now ready to start with the installation of your Technicolor Gateway.
161 GETTING STARTEDDMS-CTC-20101206-0033 v0.1
172 GUIDED INSTALLATIONDMS-CTC-20101206-0033 v0.12 Guided InstallationIntroductionIn the guided installation, the Setup wizard on the Setup CD will assist you with the installation of your Technicolor Gateway.If you do not want to use the Setup CD or if the Setup CD is not included in your package, follow the installation procedure described in “3 Manual Installation” on page 19.RequirementsTo use the guided installation you must comply with the following requirements:Your computer must run one of the following operating systems:Microsoft Windows 7 and higherMicrosoft Windows 7 x64 and higherMicrosoft Windows Vista and higherMicrosoft Windows XP Service Pack 2 (SP2) and higherMac OS X 10.6 (Snow Leopard)Mac OS X 10.5 (Leopard)Mac OS X 10.4 (Tiger)You must have administrative rights on your computer.If you do not comply with these requirements, use the “3 Manual Installation” on page 19.Running the Setup wizardTo start the Setup wizard:1Insert the Setup CD into your computer's CD- or DVD drive. 2If your computer runs:Microsoft Windows: The Setup CD starts automatically.If the Setup CD does not autostart, see “The Setup CD does not start automatically” on page 100.Mac OS X: Double-click Menu in the window with the content of the Setup CD.3Select the language of your choice and click OK.4The Setup wizard will now guide you through the installation of your Technicolor Gateway.5At the end of the installation, the following screen appears:Select Go to the Technicolor Gateway web interface if you want to go to the Technicolor Gateway GUI after closing the wizard. On the Technicolor Gateway GUI, you can configure all services of your Technicolor Gateway.
182 GUIDED INSTALLATIONDMS-CTC-20101206-0033 v0.16Click Finish.7The CD menu appears.CD MenuOn the CD Menu, you can click:Initial Setup to connect your computer to the Technicolor Gateway and configure your local network.Reconfigure my Technicolor Gateway to fully reconfigure your Technicolor Gateway.Setup my computer to connect your computer to the Technicolor Gateway network.Documentation to view a list of the documentation that is available for your Technicolor Gateway.Visit technicolor.com to visit the online support sections.In case of problemsIf you encounter problems during this installation please refer to “11.1 Setup Troubleshooting” on page 100.Backup your configurationOnce you successfully installed your Technicolor Gateway, it is recommend to backup your configuration. This will allows you to return to this configuration when needed (for example, after misconfiguration).For more information, see “4.2 Backing Up/Restoring your Configuration” on page 39If you reconfigure your Technicolor Gateway via the CD menu, the Technicolor Gateway will be reconfigured from scratch. All your current settings will be lost. If you only want to make small changes to your configuration (for example, changing the security), we recommended you to do this via the Technicolor Gateway GUI. For more information, see “4.1 Technicolor Gateway GUI” on page 34.Actual available items depend on the Setup CD delivered with your Technicolor Gateway.
193 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13 Manual InstallationInstallationThis chapter will help you to manually install your Technicolor Gateway.Setting up your networkProceed as follows:1Connect your Technicolor Gateway to your service provider’s network.For more information, see “3.1 Connecting the Technicolor Gateway to your Service Provider’s Network” on page 20.2Power on the Technicolor Gateway.For more information, see “3.2 Powering on the Technicolor Gateway” on page 25.3Connect your computer to the Technicolor Gateway.For more information, see “3.3 Connecting Your Network Devices to the Technicolor Gateway” on page 26.4Configure your Technicolor Gateway.For more information, see “3.4 Configure the Technicolor Gateway” on page 29.5Connect your phones.For more information, see “6 Telephony” on page 47.6Share your content or media on your local network, continue with “8 Sharing Content on your Technicolor Gateway” on page 65.7If you purchased the mobile USB adapter, setup the 3G backup connection.For more information, see “3.5 Setting Up the 3G Fall-Back WAN Connection” on page 30.8Once you successfully installed your Technicolor Gateway, it is recommend to backup your configuration. This will allows you to return to this configuration when needed (for example, after misconfiguration). For more information, see “4.2 Backing Up/Restoring your Configuration” on page 39.
203 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13.1 Connecting the Technicolor Gateway to your Service Provider’s NetworkIdentifying your setupIf you are using the Technicolor Gateway as:DSL Gateway, continue with “3.1.1 Setting up your Technicolor Gateway as DSL Gateway” on page 21.Local Router, continue with “3.1.2 Setting up your Technicolor Gateway as Local Router” on page 24.For more information, see “1.2 User Scenarios” on page 5, you can use your Technicolor Gateway in either of the following scenarios
213 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13.1.1 Setting up your Technicolor Gateway as DSL GatewayIntroductionThis section helps you to connect the Technicolor Gateway to your service provider’s network.Signal arriving at your homeThe Line signal that arrives at your home consists the following components:A Phone signal carrying the traffic for telephony.A DSL signal carrying the Internet traffic.DSL Gateways have a built-in solution to remove the Phone component. No additional devices are needed, you can connect them directly to the Line.Telephones do not have this capability, so here you have to use a filter or splitter to remove the DSL signal.How does a filter/splitter look likeA splitter/filter is a box that typically has the following connectors:A Line inputThis connector must be connected to the input signal that needs to be filtered.A Phone/PSTN outputThis connector offers filtered output signal. It only contains the Vo i c e component and can only be used for connecting phones.A Modem/DSL output (optional)This connector offers unfiltered output. It contains both the Phone and DSL signal and can be used to connect your Technicolor Gateway.Connecting the cablesThe procedure to be followed depends on the fact if this filter has been integrated into your Technicolor Gateway or not.Check the label of your Technicolor Gateway. If the product name contains:“wIF” (for example Technicolor TG789vn v3 wIF) then your Technicolor Gateway has an integrated filter. No external filters are needed. Follow the steps described in “Scenario 2: A Technicolor Gateway without integrated filter” on page 22.No “wiF” (for example Technicolor TG789vn v3) then your Technicolor Gateway does not have an integrated filter. Follow the steps described in “Scenario 2: A Technicolor Gateway without integrated filter” on page 22.Scenario 1: A Technicolor Gateway with integrated filterProceed as follows:1Take the DSL cable. This is the gray cable that is included in your box.This Phone signal is only used for communication over the traditional telephone network (PSTN). Voice over IP communication will be carried by the DSL signal.DSL + VoiceVoiceDSL + VoiceServiceProviderFilter/SplitterLINEPHONEMODEM
223 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.12Plug one end of the cable in the grey DSL port on the back of your Technicolor Gateway.3Plug the other end of the cable:In the DSL/Modem output of your splitter/filter.Directly into the telephone wall outlet if there is no splitter/filter between the network terminator and your local phone network.Scenario 2: A Technicolor Gateway without integrated filterProceed as follows:1Take the DSL cable. This is the grey cable that is included in your box.2Plug one end of the cable in the grey DSL port on the back of your Technicolor Gateway.3Plug the other end of the cable into the DSL/MODEM output port of your filter/splitter.DSLDSL
233 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.1If your Technicolor Gateway has a black PSTN port on the back, you are able to use the PSTN (this is the traditional telephone network) as a backup for your Voice over IP connection. When the VoIP connection is down, the Technicolor Gateway will automatically switch back to the PSTN network.To setup this backup connection:1Take a Telephone Cable2Plug one end of the cable in the black PSTN port on the back of your Technicolor Gateway.3Plug the other end of the cable into the Phone output port of your filter/splitter.PSTN
243 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13.1.2 Setting up your Technicolor Gateway as Local RouterProcedureProceed as follows:1Take an Ethernet cable. If your box contains an Ethernet cable with red connectors, you can use that cable.2Plug one end of the cable in the red WAN port on the back of your Technicolor Gateway.3Plug the other end of the cable into the Ethernet port of your Internet gateway/modem.The WAN port can only be used to connect your Technicolor Gateway to an Internet gateway/modem. You can not use it to connect other devices (for example, a computer) to the Technicolor Gateway.WAN
253 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13.2 Powering on the Technicolor GatewayProcedureProceed as follows:1Connect the power cord to the power port of the Technicolor Gateway.2Plug the other end of the power cord into an electrical outlet.3Press the power button to turn on the Technicolor Gateway.4Wait at least two minutes to allow the Technicolor Gateway to complete the start up phase.
263 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13.3 Connecting Your Network Devices to the Technicolor GatewayChoose your connection methodTo connect your device via:A wireless connection, continue with “3.3.1 Setting up a Wireless Connection” on page 27.A wired connection, continue with “3.3.2 Setting up a Wired Connection” on page 28.
273 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13.3.1 Setting up a Wireless ConnectionThe Technicolor Gateway access pointYour Technicolor Gateway is equipped with a wireless access point that supports the following standards:IEEE 802.11n (2.4 Ghz)IEEE 802.11gIEEE 802.11bRequirementsYour network device must be equipped with a WiFi-certified wireless client.Connection speedWhen setting up your wireless network, keep in mind that the following factors may have a negative impact on your wireless connection speed:The obstacles (walls, ceilings,...) between the wireless client and the access point.Distance between the wireless client and the access point.To fully benefit from the improved connection speed offered by the IEEE 802.11n standard, it is recommended to only connect IEEE 802.11n wireless clients to your Technicolor Gateway. Connecting older (for example, IEEE 802.11g) wireless clients may also slow down connection speed of the IEEE 802.11n capable clients.If you have problems with your wireless performance, see “Poor Wireless Connectivity or Range” on page 103.To set up a wireless connectionsFor more information on how to setup a wireless connection between your network device and your Technicolor Gateway, see “5 The Technicolor Gateway Wireless Access Point” on page 41.
283 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13.3.2 Setting up a Wired ConnectionRequirementsBoth your network device (for example, a computer, a gaming console,...) and Technicolor Gateway must have a free Ethernet port.Your network device must be configured to obtain an IP address automatically. This is the default setting.Ethernet cableIn your package, you will find a cable with yellow connectors. This is the Ethernet cable.ProcedureProceed as follows:1Connect one end of the Ethernet cable to one of the yellow Ethernet ports of your Technicolor Gateway: 2Connect the other end of the Ethernet cable to your network device.3Your network device is now connected to your network. No additional configuration is needed unless specified by your service provider.You can not use the red WAN port to connect to the local Ethernet network. The WAN port can only be used to connect your Technicolor Gateway to your broadband source.For more information, see “1.2 User Scenarios” on page 5.The Technicolor Gateway does not support Power over Ethernet (PoE). All network devices that are connected to the Technicolor Gateway must be powered by their own power source.
293 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13.4 Configure the Technicolor GatewayIntroductionIf your service provider did not preconfigure your Technicolor Gateway, you may have to configure the Technicolor Gateway via its Graphical User Interface (GUI).RequirementsJavaScript must be enabled on your web browser (this is the default setting). For more information, consult the help of your web browser.ProcedureProceed as follows:1Open your web browser.2The Technicolor Gateway informs you that you have not yet configured your Technicolor Gateway.If this window does not appear, browse to http://dsldevice.lan or to the IP address of your Technicolor Gateway (by default: 192.168.1.254) and click Technicolor Gateway on the menu on the left-hand side.3Click Setup my Technicolor Gateway.4The Easy Setup wizard appears. This wizard will guide you through the configuration of your Technicolor Gateway. Click Next and follow the instructions.
303 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13.5 Setting Up the 3G Fall-Back WAN ConnectionIntroductionMany SOHO (Small Offices, Home Offices) and SME (Small/Medium Enterprises) businesses choose DSL as their access technology for a Wide Area Network (WAN) connection because this is typically cheaper than using leased lines. A dropout of a DSL line can however have expensive consequences due to inaccessibility of the Internet and E-mail. Therefore backup solutions are available that provide an alternative path when the DSL line is down.For example it is possible to switch to 2G / 3G mobile access technologies such as GPRS, UMTS, HSDPA, HSUPA, HSPA+, WIMAX and LTE when internet connectivity is not available via the main WAN connection. By plugging a mobile USB adapter into one of the USB ports of your Technicolor Gateway, IP connectivity via a 2G / 3G network becomes possible.3G is an umbrella-term to indicate the third generation mobile telephony technology. The services associated with 3G provide the ability to transfer both voice data and non-voice data. 3G networks are the successors of the 2G networks, such as the GSM networks and provide new services and higher data transfer speeds.What do I need?To start using 2G / 3G as a connection on the Technicolor Gateway, you need:A mobile USB adapterA registered Security Identity Module (SIM) card.Configure 2G / 3G as WAN connectionProceed as follows:1Configure your mobile connection.For more information, see “3.5.1 Managing your Mobile Connection with the Technicolor Gateway GUI” on page 31.2Insert your mobile USB adapter.For more information, see “3.5.2 Inserting a Mobile USB Adapter” on page 32.3Now your mobile connection is up and ready to use.ResultTechnicolor Gateway will automatically enable your 3G backup connection when both of the following conditions are met:The main Internet connection has been unavailable for at least 60 seconds.The Technicolor Gateway received a request to access the Internet (for example, when browsing to an Internet web site).The Technicolor Gateway will automatically disable the 3G connection in either of the following cases:The main Internet connection is available again. In this case the Technicolor Gateway switches back to the main Internet connection.No Internet traffic has been detected during the last 10 seconds. For example, you finished surfing the Internet.If you need to remove your mobile USB adapter, make sure the Technicolor Gateway is powered off first.
313 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13.5.1 Managing your Mobile Connection with the Technicolor Gateway GUIIntroductionYou can view and manage the parameters of your mobile connection via the Technicolor Gateway GUI.ProcedureTo manage your mobile USB connection via the Technicolor Gateway GUI:1Browse to the Technicolor Gateway GUI.2On the Broadband Connection menu, click Internet Services.3Click View more... for the mobile USB connection. The Overview page of the mobile USB connection is shown. 4In the location bar, click Configure. The Configure page of the mobile connection appears.5Under Mobile Information, update the following fields if necessary:APN:The public APN used to access the Internet, or the private APN to access a local network.Operator Mode:2G / 3G / automatic (let the Technicolor Gateway choose the best operator mode)Pin:The PIN code of your SIM card.6Click Apply to apply your configuration changes.Configuration changes via the Technicolor Gateway GUI are automatically saved.
323 MANUAL INSTALLATIONDMS-CTC-20101206-0033 v0.13.5.2 Inserting a Mobile USB AdapterProcedureOnce the mobile connection is configured you can proceed as follows to insert the mobile USB adapter:1Power off the Technicolor Gateway.2Insert your SIM card into the mobile USB adapter.3Plug the mobile USB adapter in (one of) the USB port(s) of your Technicolor Gateway:4Power on the Technicolor Gateway.If you do not power off the Technicolor Gateway first, the mobile USB adapter will not be detected.
334 CONFIGURATION TOOLSDMS-CTC-20101206-0033 v0.14 Configuration ToolsConfiguration ToolsYou can use the following tools to configure your Technicolor Gateway:The Technicolor Gateway Setup CD allows you to configure your Technicolor Gateway and helps you to connect your computers to the Technicolor Gateway. For more information, see “2 Guided Installation” on page 17.The Technicolor Gateway GUI allows you to configure your Technicolor Gateway via your web browser.For more information, see “4.1 Technicolor Gateway GUI” on page 34.
344 CONFIGURATION TOOLSDMS-CTC-20101206-0033 v0.14.1 Technicolor Gateway GUIIntroductionThe Technicolor Gateway Graphical User Interface (GUI) allows you to configure your Technicolor Gateway using your web browser.RequirementsJavaScript must be enabled on your browser (this is the default setting). For more information, consult the help of your web browser.
354 CONFIGURATION TOOLSDMS-CTC-20101206-0033 v0.14.1.1 AccessAccessing the Technicolor Gateway GUIProceed as follows:1Open your web browser.2Browse to http://dsldevice.lan or to the IP address of your Technicolor Gateway (by default: 192.168.1.254).3If you have protected your Technicolor Gateway with a user name and password, the Technicolor Gateway will prompt you to enter these. Enter your user name and password and click OK.4The Technicolor Gateway GUI appears.Access the Technicolor Gateway via UPnPYou can also access the Technicolor Gateway GUI using the Internet Gateway Device (IGD) icon if your computer runs one of the following operating systems:Microsoft Windows 7Microsoft Windows VistaMicrosoft Windows XPFor more information, see “9.1 UPnP” on page 80.Remote accessIt is also possible to access the Technicolor Gateway GUI from the Internet. For more information, see “4.3 Access From the Internet” on page 40.For more information, see “4.1.3 Protecting Access to the Technicolor Gateway” on page 38.
364 CONFIGURATION TOOLSDMS-CTC-20101206-0033 v0.14.1.2 ComponentsOverviewDepending on your user right and location on the GUI, the following components can be available:MenuThe menu consists of the following menu items:Home:Allows you to go back to the Technicolor Gateway home page.Technicolor Gateway:Provides basic information on the Technicolor Gateway.Broadband Connection:Allows you to view/configure your broadband connections.To o l b o x :Allows you to configure the network services and security settings of your Technicolor Gateway.Home Network:Allows you to manage your local network.Help:Allows you to view context-related help information.Label Description1Menu2Login section3Language bar4Notification area5Navigation bar6Content pane7Tasks pane4513672
374 CONFIGURATION TOOLSDMS-CTC-20101206-0033 v0.1Each of these items contain a number of sub-menu items.Login sectionIn the login section you can see the current user name.By clicking the user name, you can:Change your password.Switch to another user.Language barIf more than one GUI language is available, a language bar is showed. This language bar allows you to change the language of the Technicolor Gateway GUI.Notification areaThe notification area displays:Error messages, indicated by a red traffic light.Warning messages, indicated by an orange traffic light.Information messages, indicated by a green traffic light.Navigation barThe Navigation bar displays your current position in the Technicolor Gateway GUI.Some page are available in different configuration levels. These pages have additional links (for example, Overview, Configure) in the right part of the navigation bar that allow you to switch between the configuration levels.Content paneThe content pane displays the information and configurable items of the selected item.Tasks paneTo allow a quick configuration of your Technicolor Gateway, some pages may offer you a number of related tasks in the Pick a task list. These tasks will guide you to the page where you can perform the selected task.If none of these events occur, the notification is not shown.
384 CONFIGURATION TOOLSDMS-CTC-20101206-0033 v0.14.1.3 Protecting Access to the Technicolor GatewayIntroductionTo prevent that every user on your local network can access the Technicolor Gateway, the Technicolor Gateway is secured with a user name and password.Default user nameThe default user name is Administrator.Default passwordThe default password is either blank or the ACCESS KEY printed on the label of your Technicolor Gateway. This depends on the settings chosen by your Service Provider.Protected itemsThe following items are protected by these is will secure access to:The Technicolor Gateway GUI.The embedded FTP Server.for more information, see “8.3 The FTP Server” on page 74.How to change your passwordProceed as follows:1On the Toolbox menu, click User Management.2In the Pick a task list, click Change my password.3Enter your new password and click OK.4Your new password is now active. The next time that you log on to the Technicolor Gateway GUI you will have to enter this password.It is recommended to change the default password settings.Choose a password that your can easily remember or write it down. If you forget your password the only option is to reset your Technicolor Gateway. For more information, see “11.6 Reset to Factory Defaults” on page 105.This password will also be used by the network file server and FTP server.For more information about the network file server and FTP server, see “8 Sharing Content on your Technicolor Gateway” on page 65
394 CONFIGURATION TOOLSDMS-CTC-20101206-0033 v0.14.2 Backing Up/Restoring your ConfigurationIntroductionOnce you have configured your Technicolor Gateway to your needs, it is recommended to backup your configuration for later use. This way you can always return to your working configuration in case of problems.Backing up your configurationProceed as follows:1Browse to the Technicolor Gateway GUI.For more information, see “4.1 Technicolor Gateway GUI” on page 34.2On the Technicolor Gateway menu, click Configuration.3In the Pick a task list, click Save or Restore Configuration.4Under Backup current configuration, click Backup Configuration Now.5The Technicolor Gateway prompts you to save your backup file.6Save your file to a location of your choice.Restoring your configurationProceed as follows:1Browse to the Technicolor Gateway GUI.For more information, see “4.1 Technicolor Gateway GUI” on page 34.2On the Technicolor Gateway menu, click Configuration.3In the Pick a task list, click Save or Restore Configuration.4Under Restore saved configuration, click Browse and open your backup file.5The Technicolor Gateway restores your configuration.Do not edit the backup files, this may result in corrupt files making them worthless as configuration backup.Backup files usually have.ini as extension.
404 CONFIGURATION TOOLSDMS-CTC-20101206-0033 v0.14.3 Access From the InternetModesTo access your Technicolor Gateway from the Internet, you can choose between two modes:Permanent Mode (Remote Access):The remote session ends when you disable remote assistance or after restarting your Technicolor Gateway.Temporary Mode (Remote Assistance):The remote session ends when you disable remote assistance, after restarting your Technicolor Gateway or after 20 minutes of inactivity.To enable Remote Assistance / Remote Access.To enable remote assistance/access:1Browse to the Technicolor Gateway GUI.For more information, see “4.1 Technicolor Gateway GUI” on page 34.2 Complete and check the following parameters:Mode:Select the mode that you want to use.URL:Contains the URL that must be used to access the Technicolor Gateway from the Internet.User name and Password:Contains the user name and password are needed to access your Technicolor Gateway remotely. If wanted you can change the automatically generated password in the Password box.3Click Enable Remote Assistance.Accessing your Technicolor Gateway from the InternetProceed as follows:1Open your web browser.2Type the URL that was listed in the URL field on the Remote Assistance page (for example https://141.11.249.150:51003).3Enter the user name and password that you specified on the Remote Assistance page.4The Technicolor Gateway GUI appears.It is now possible for a remote user to access your Technicolor Gateway via the specified URL using the provided user name and password.Enabling remote assistance is only possible when you are connected to the Internet.You can replace the IP address in this URL by the dynamic DNS host name if you enabled and configured Dynamic DNS. For more information, see Dynamic DNS.Example: https://141.11.249.150:51003 can be replaced by https://mygateway.dyndns.org:51003.
415 THE TECHNICOLOR GATEWAY WIRELESS ACCESS POINTDMS-CTC-20101206-0033 v0.15 The Technicolor Gateway Wireless Access PointIntroductionThis section will help you set up your wireless network.What you need to set up a wireless networkTo set up a wireless network, you need the following components:A Wireless Access Point (already integrated into your Technicolor Gateway)A Wireless client the device that you want to connect (for example, a computer, smartphone, network printer,...)Wireless Access PointThe wireless access point is the heart of your wireless network. The wireless access point:Connects different wireless devices.Secures the data sent over wireless connection.The Technicolor Gateway comes with an integrated wireless access point.Wireless clientThe wireless client allows you to connect a device, typically a computer, to a wireless access point. Both built-in and external (for example via USB) clients are available.Check the documentation of your computer if you are not sure if your computer is equipped with a wireless client.Configuring your wireless clientsFor more information on how to establish a wireless connection to the Technicolor Gateway, see “5.1 Connecting Your Wireless Client via WPS” on page 42 and “5.2 Connecting Your Wireless Client without WPS” on page 44.Secure your wireless connection!When using an unsecured connection, everyone who is within the range of your Technicolor Gateway can access your network. If not:People may use your connection to access the Internet.Hackers may use your connection to commit computer crimes.You can easily prevent this by securing your wireless access point. For more information, see “5.3 Securing Your Wireless Connection” on page 45.Devices like media players and smartphones may also have a built-in wireless client. Check the documentation of your device for more information.
425THE TECHNICOLOR GATEWAY WIRELESS ACCESS POINTDMS-CTC-20101206-0033 v0.15.1 Connecting Your Wireless Client via WPSWPSWi-Fi Protected Setup (WPS) allows you to add new wireless clients to your local network in a swift and easy way, without the need to enter any of your wireless settings (network name, wireless key, encryption type).RequirementsYour wireless client must support WPS. Check the documentation of your wireless client for this.Your Technicolor Gateway must use WPA(2)-PSK encryption (default encryption) or no encryption. WPS with WEP encryption is not possible.ProcedureProceed as follows:1Shortly press the WPS button on the Technicolor Gateway:2The WPS button LED starts blinking orange. This indicates that the Technicolor Gateway is now searching for wireless clients that are in registration mode. You now have two minutes to start WPS on your wireless client.3Start WPS on your wireless client.4The Technicolor Gateway is now exchanging the security settings.5At the end of the procedure the status of the WPS LED will change to either of the following:Solid greenThis indicates that you have successfully registered your wireless client. You are now connected to the Technicolor Gateway network.Blinking redThis indicates that the Technicolor Gateway could not find your wireless client. Use the same procedure to try again (you do not need to wait until the LED turns off).TroubleshootingIf you are having trouble connecting your wireless client via WPS, this may be cause by one of the following reasons:WPS can not be correctly executed:Configure your wireless manually. For more information, see “5.2 Connecting Your Wireless Client without WPS” on page 44.Both Windows 7 and Windows Vista Service Pack 1 have native WPS support.
435 THE TECHNICOLOR GATEWAY WIRELESS ACCESS POINTDMS-CTC-20101206-0033 v0.1Your wireless client is out of range:If possible move your wireless client closer to your Technicolor Gateway or use a wireless repeater to extend the range of your wireless network.Another device is interfering on the selected wireless channel:Change the wireless channel of your Technicolor Gateway. For more information, see “Change the wireless channel” on page 103.
445THE TECHNICOLOR GATEWAY WIRELESS ACCESS POINTDMS-CTC-20101206-0033 v0.15.2 Connecting Your Wireless Client without WPSBefore you startBefore you can connect a wireless client (for example, a computer) to your wireless network you need to know the wireless settings that are currently used by the Technicolor Gateway, i.e.:The Network Name (SSID)The wireless keyWhat Network Name (SSID) is my Technicolor Gateway using?If you did not change the SSID, your Technicolor Gateway uses the Network Name that is printed on the back panel label of your Technicolor Gateway.What wireless key is my Technicolor Gateway using?If you did not change the security settings, no wireless key is used. Forgot your wireless key?If you have changed the wireless settings manually and you can’t remember your settings, try one of the following:1Use a computer that is already connected to your network.2Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.3On the Home Network menu, click Wireless.4In the upper-right corner, click Details.5Under:Configuration, you can find the network name (SSID).Security, you can find the encryption.Connecting your wireless clientConfigure your wireless client with the same wireless settings as your Technicolor Gateway (network name and wireless key). For more information, consult the documentation of your wireless client.If your service provider did choose to use a default wireless key, use the Wireless Key that is printed on the bottom panel label of your Technicolor Gateway.If none of your computers is connected yet, connect one with an Ethernet cable. For more information, see “3.3.2 Setting up a Wired Connection” on page 28.
455 THE TECHNICOLOR GATEWAY WIRELESS ACCESS POINTDMS-CTC-20101206-0033 v0.15.3 Securing Your Wireless ConnectionIntroductionYou can protect the wireless communication between the wireless clients and your Technicolor Gateway with a wireless key. This means that:Only clients which use the correct Network Name (SSID) and wireless key can connect to your network.All data passing through your wireless access point is secured and encrypted.Encryption typesOver the years a number of encryption types have been developed. The list below gives you an overview of the supported encryption types ordered by descending security level; you will find the highest level of security at the top of the list:WPA-PSK Encryption:The wireless connection is secured with a pre-shared key that has been defined by the user. Wireless clients must be configured with this key before they can connect to the Technicolor Gateway. The Technicolor Gateway supports the following WPA versions (ordered by descending security):WPA2:The most recent and most secure version of WPA. Choose this version if you are sure that all your wireless clients support WPA2.WPA+WPA2:This is a mixed mode. In this mode WPA2, is the preferred encryption type but wireless clients do not support WPA2, can still use WPA as encryption type. Choose this option if not all of your wireless clients support WPA2 or if you are not sure. Wireless clients that support WPA2 will use WPA2, the others will use WPA.WPA:The first version of WPA. Choose this option if you are sure that none of your wireless clients support WPA2.WEP Encryption:The least safe encryption type used for wireless connections. Like WPA-PSK it uses a user-defined key, but WEP has been proven to have security issues.ConfigurationProceed as follows:1Open the Technicolor Gateway GUI.2Under Home Network, click Wireless.3The Wireless Access Point page appears. In the upper-right corner, click Configure.4Under Encryption, select Use WPA-PSK Encryption.5In the WPA-PSK Encryption Key box, type a the key of your choice. The key must be in one of the following formats:8 to 63 alphanumeric characters. For example: MyKey1238 to 64 hexadecimal characters (characters from 0 to 9 and from A to F). For example: C54F48A5.If you want to configure WPA2 on the built-in wireless utility of Windows XP Service Pack 2 (SP2), you first have to:Upgrade your Windows XP to Service Pack 3.- or -Install the following update: http://support.microsoft.com/kb/917021.Although the Technicolor Gateway allows you to use WEP or no security, we strongly advise against using one of them! Use WPA(2)-PSK instead.
465THE TECHNICOLOR GATEWAY WIRELESS ACCESS POINTDMS-CTC-20101206-0033 v0.16In the WPA-PSK Version list, click the WPA-version of your choice. For more information, see “Encryption types” on page 45.7Click Apply.8Reconnect your wireless client(s) to the Technicolor Gateway using these new security settings.For more information, see “5.1 Connecting Your Wireless Client via WPS” on page 42 or “5.2 Connecting Your Wireless Client without WPS” on page 44.
476 TELEPHONYDMS-CTC-20101206-0033 v0.16 TelephonyVoice over IP (VoIP)VoIP is a technology in which telephone calls are made over the Internet. This allows you to save on communication costs, especially for long-distance calls.The expensive solutionTo be able to make your phone calls over the Internet you could either:Buy an IP phone.These IP phones are special phones that you can connect to your Internet Gateway.Install VoIP software on your computer and make your phone calls via your computer.The Technicolor solutionWith the Technicolor Gateway you can make both VoIP and traditional telephone calls using a traditional analogue phone.If your Technicolor Gateway is not powered, the traditional telephone network (if connected) will automatically selected. This way you are still able to make emergency calls.In this chapterThis chapter covers following topics:To p i c Page6.1 Setting Up Your Telephone Network 486.2 Address Book 526.3 Telephony Services 546.4 Viewing Call Logs 59
486 TELEPHONYDMS-CTC-20101206-0033 v0.16.1 Setting Up Your Telephone NetworkProcedureTo set up your telephone network, follow these steps:1Connect your traditional phone(s), DECT base station or fax to the green Phone port(s) on the back panel of your Technicolor Gateway.2Connect your Technicolor Gateway to the traditional network.For more information, see “6.1.1 Connection to the Traditional Telephone Network” on page 49.3Configure the VoIP service on your Technicolor Gateway.For more information, see “6.1.2 Configuring the Technicolor Gateway VoIP Service” on page 50.
496 TELEPHONYDMS-CTC-20101206-0033 v0.16.1.1 Connection to the Traditional Telephone NetworkCombining VoIP with the traditional telephone networkSome service providers use the traditional telephone network (PSTN) as a backup solution for your VoIP connection. This way, you can still make calls over the traditional network if the VoIP service is down (for example, your Technicolor Gateway is powered off).Be aware that, if you are not connected to the traditional telephone network, emergency calls will not be possible when your Internet connection is down or your Technicolor Gateway is powered off.ApplicabilityIf your Technicolor Gateway:Has an integrated filter, no additional connections are needed.The DSL port must be directly connected to your telephone outlet. Do not put any filter or splitter between them!How do I know if my Technicolor Gateway has an integrated filter?Check if the product name printed on the label of your Technicolor Gateway ends with “wIF” (with Integrated Filter). If this suffix is not present, then your Technicolor Gateway does not have an integrated filter.Does not have an integrated filter, check if your Technicolor Gateway has a PSTN port on the back panel (for more information, see “PSTN Port (optional)” on page 10). If your Technicolor Gateway has:A PSTN port:Connect the PSTN port to the Phone output of your filter or splitter.No PSTN port, no connections are needed.This is a VoIP-only variant. All calls passing through the Technicolor Gateway will be done via VoIP.
506 TELEPHONYDMS-CTC-20101206-0033 v0.16.1.2 Configuring the Technicolor Gateway VoIP ServiceIntroductionIf your VoIP service has not been configured yet, follow the instructions in this section.How can I check if the VoIP service has already been configured?If the Phone LED is:Solid or blinking green then the VoIP service is configured correctly. No configuration is needed.Off then telephony service is not configured (yet). Follow the instructions below.RequirementsYour Internet connection must be up and running before you can configure Internet telephony.Configuring the VoIP settingsProceed as follows:1Enter the proxy and registrar settings.2Enter your VoIP account settings.Enter the proxy and registrar settingsProceed as follows:1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2On the Toolbox menu, click Te l e p h o n y.3In the Navigation bar, click Expert configure.4Complete the following fields based on the settings provided by your VoIP provider:Proxy:Type the URL (for example: sip.provider.com) or IP address of the proxy.Registrar:Type the URL (for example: sip.provider.com) or IP address of the registrar.Registrar Port and Proxy Port.In most cases the default port (5060) will be used. Only change these values if your provider is using other port numbers.5Click Apply.Enter your VoIP account settingsProceed as follows:1In the Navigation bar, click Configure.2Under Service Configuration, select Enable Telephony.3Under Telephone Numbers, complete the following fields:SIP URI:The Uniform Resource Identifier (URI) of your SIP account (for example: 035051979, john.doe,...). This is the telephone number that people have to dial to call you.Username:The user name of your VoIP account (for example: 035051979, john.doe,...).
516 TELEPHONYDMS-CTC-20101206-0033 v0.1Password:The password of your VoIP account.Displayname:The name that you want people to see on the display of their phone when you are calling.Your VoIP provider may not support this feature.Abbreviated number:An internal number to call the phones associated with this VoIP account.Port:The phone port that you want to associate with this VoIP account. selectAll to use this VoIP account for all connected phone.Phone 1/2 to use this VoIP account for the phone connected to the Phone 1/2 port of your Technicolor Gateway.4Click Apply.Verifying Telephone ConnectivityProceed as follows to verify the voice connection:1Make sure the Technicolor Gateway is turned on.2Make sure the Internet telephony service is enabled and configured. The Phone LED must be solid green.3Pick up your phone, wait for the dialling tone, and dial the number.
526 TELEPHONYDMS-CTC-20101206-0033 v0.16.2 Address BookIntroductionThe Address Book page allows you to:Store your contacts on the Technicolor Gateway GUI.Initiate a call or send a message by clicking the phone number or e-mail address in the contact details.Everyone with access to the Technicolor Gateway GUI can view and use the address book.Accessing the Address Book pageProceed as follows:1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2On the Toolbox menu, click Address Book.3The Address Book page appears.For each contact, you can provide the following information:Business: to make a call to the contact’s business telephone numberHome: to make a call to the contacts home telephone numberMobile: to make a call to the contact’s mobile telephone numberOther or SIP uri: to make a call to the contact’s VoIP telephone number E-mail to send an E-mail message to the contact with your e-mail client.Managing contactsClick... To . . .Add Add a contactEdit Edit a contactDelete Delete a contactAll information provided per contact is optional except for the last and first name. The information can be updated or completed at any time.Making a phone call from the address bookProceed as follows:1Browse to the Address Book page.
536 TELEPHONYDMS-CTC-20101206-0033 v0.12Click on the phone number of your contact.3The following page appears:4Pick up the phone.5The Technicolor Gateway is now initiating the call. Your contact’s phone is now ringing.6At the end of the conversation, click Done to go to the Last Calls page. This page allows you to view the statistics of your last calls (including the call that you just made).You can use the buttons in the Remote Number column to make a new call to one of the contacts in your call log.
546 TELEPHONYDMS-CTC-20101206-0033 v0.16.3 Telephony ServicesIntroductionTelephony services add extra functionality to your phone. For example: putting a call on hold, transferring calls,...RequirementsBefore you can use a service, must both be:1Supported by your service provider.2Activated on your Technicolor Gateway.Checking if a telephone service is activated/supportedTo check which services are supported or activated, proceed as follows:1Browse to the Technicolor Gateway GUI.For more information, see “4.1 Technicolor Gateway GUI” on page 34.2On the Toolbox menu, click Te l e p h o n y.3In the Navigation bar, click Configure.4In the Pick a task list, click View Telephony Services.5Under Te lephony Services, you can see the services that are supported by your provider.In the Activated column, you can see if this service is also activated on the Technicolor Gateway.6To (de)activate a service, proceed with “6.3.1 Activating a Telephony Service on your Technicolor Gateway” on page 55.
556 TELEPHONYDMS-CTC-20101206-0033 v0.16.3.1 Activating a Telephony Service on your Technicolor GatewayHow can I (de)activate a service on my Technicolor Gateway?You can (de)activate services in two ways:Via the Technicolor Gateway GUI.Via (de)activation codes on your phone.Activating a Telephony Service via the Technicolor Gateway GUIProceed as follows:1Browse to the Technicolor Gateway GUI.For more information, see “4.1 Technicolor Gateway GUI” on page 34.2On the Toolbox menu, click Te l e p h o n y.3In the Navigation bar, click Configure.4In the Pick a task list, click View Telephony Services.5In the Navigation bar, click Configure.6Under Telephony services you can now activate or deactivate the services of your choice:To :Activate a service select the check box next to the service.Deactivate a service clear the check box next to the service.7Click Apply.Activating a Telephony Service via Your PhoneTo (de)activate one of the services just dial the corresponding code on your phone. For example, to activate Call Hold dial *94; to deactivate the service dial #94.To know which code to use:1Browse to the Technicolor Gateway GUI.For more information, see “4.1 Technicolor Gateway GUI” on page 34.2On the Toolbox menu, click Te l e p h o n y.3In the Navigation bar, click Configure.4In the Pick a task list, click View Telephony Services.5In the Te lephony Services table, you can find the activation and deactivation codes.
566 TELEPHONYDMS-CTC-20101206-0033 v0.16.3.2 Common Telephony ServicesIntroductionThis section provides an overview of the functions that will be available if you activate one of the following services:Call Hold serviceCall Waiting serviceConference Call (3 Party) serviceCall TransferFor more information on the other services, please contact your service provider.Call Hold serviceIf the Call Hold service is activated, you can use the following functions:To . . . Press... IllustrationPut an active call on hold and enable a call set up (the dial tone is generated)R, 2BAYouon holddial toneBAYouactiveYou pressR, 2Terminate the call on hold R, 0BAYouactiveBAYouactive on holdYou pressR, 0Terminate an active call and switch to the call on hold R, 1BAYouactiveBAYouactive on holdYou pressR, 1Retrieve the call on hold (when there is no active call) R, 1BAYouactiveBAYouon holdYou pressR, 1Terminate an active call and enables a call set up (the dial tone is generated)R, 9BAYoudial toneon holdBAYouactive on holdYou pressR, 9
576 TELEPHONYDMS-CTC-20101206-0033 v0.1Call Waiting serviceIf the Call Waiting service is activated, you can use the following functions:To . . . Press... IllustrationTerminate an active call and switch to an incoming call R, 1BAYouactiveBAYouactive incomingYou pressR, 1Reject an incoming call R, 0BAYouactiveBAYouactive incomingYou pressR, 0Switch between an active call and a call on hold R, 2BAYouon hold activeBAYouactive on holdYou pressR, 2Switch between an active call and an incoming call R, 2BAYouon hold activeBAYouactive incomingYou pressR, 2Conference Call (3 Party) serviceIf the Conference Call (3 Party) service is activated, you can use the following functions:To . . . Press... IllustrationEstablish a conference call (or 3 party connection) R, 3BAYouactive activeBAYouon hold activeYou pressR, 3During a conference call: put B and C on hold R, 2BAYouon hold on holdBAYouactive activeYou pressR, 2During a conference call: retrieve B and C when they are on holdR, 3BAYouactive activeBAYouon hold on holdYou pressR, 3
586 TELEPHONYDMS-CTC-20101206-0033 v0.1Call TransferIf the Call Transfer service is activated, you can use the following functions:To . . . Press... IllustrationTransfer a call R, 4BAYouactiveBAYouon hold activeYou pressR, 4
596 TELEPHONYDMS-CTC-20101206-0033 v0.16.4 Viewing Call LogsIntroductionThe Call Logs page on the Technicolor Gateway GUI lists:Successful incoming calls.Missed incoming calls.Successful outgoing calls.Failed outgoing calls.Viewing the telephony statisticsProceed as follows:1Browse to the Technicolor Gateway GUI.2On the Toolbox menu, click Te l e p h o n y.3The Te l e p h o n y page appears:On this page you can see an overview of your last calls.4To view more detailed statistics, click View telephony statistics and logs in the Pick a task list.Used iconsThe call logs use the following icons to illustrate the call type:Icon Ty p eSuccessful outgoing phone callSuccessful incoming callFailed outgoing callFailed incoming callCalling a contact from the call logYou can immediately start a new call to one of these contacts by clicking the button in the Remote Number column.
606 TELEPHONYDMS-CTC-20101206-0033 v0.1
617 SAVING ENERGY WITH YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.17 Saving Energy with Your Technicolor GatewayCode of ConductTo prove its commitment to protect the environment, Technicolor has signed the Code of Conduct, a global agreement to reduce the power consumption of broadband access devices.For more information, see “7.1 Code of Conduct” on page 62.Technicolor power saving innovationsTo further reduce the power consumption, Technicolor has developed the ECO Manager. This system constantly monitors the services provided by the Technicolor Gateway and automatically switches unused services to an ECO-friendly state. For more information, see “7.2 ECO Manager” on page 63.Next to this automated tool, you can also choose to manually disable services that you will not be using. For more information, “7.3 Manually Switching Off Services to Reduce Power” on page 64.
627 SAVING ENERGY WITH YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.17.1 Code of ConductPower statesCode of Conduct provides rules for the power consumption in:Full power state:This is the normal operation mode of the device, where all functionality is enabled.Low power state:When there is no user traffic on the device, the device should switch to low power mode. This is a state in which devices are only allowed to use a limited amount of energy to be able to power its components and respond to user activity.ExampleTake the following example:The user switches off his computer at 20:00.There are no other devices connected to the Technicolor Gateway.The Technicolor Gateway switches to low power mode. This results in a considerable drop in the overall power consumption of the Technicolor Gateway.No user trafficUser trafficTimePowerConsumptionFull power limitLow power limit20:00
637 SAVING ENERGY WITH YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.17.2 ECO ManagerIntroductionThe Technicolor Gateway constantly monitors the user activity and uses this information to optimise the power consumption:For example:The Technicolor Gateway reduces the clock frequency of the central processor when there is no or low user activity. This lowered clock frequency will result in a lower power consumption of the Technicolor Gateway.Disable the USB port(s) when they are not usedSwitch the wireless interface to power reduction mode.Wireless access point power reduction modeWhen the Technicolor Gateway access point switches to power reduction mode, the access point is switched off and is only power on periodically to be able to detect new clients. If new clients are detected the wireless access point is fully powered again. This is only possible if there are no devices connected to the Technicolor Gateway.Power reduction is disabled by default, but it is possible to enable it via the Technicolor Gateway GUI.To enable power reduction:1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2Under Home Network, click Wireless.3In the Navigation bar, click Configure.4Under Configuration:Select Power Reduction Enabled to enable power reduction.Clear Power Reduction Enabled to disable power reduction.5Click Apply.ExampleIf we use the same example as in the previous section, you can see that the Technicolor Gateway is now able to further reduce the power consumption in periods where less action is required from the Technicolor Gateway.Enabling power reduction may have impact on the reliability of your wireless connection. This feature is intended for advanced users only.No User TrafficUser TrafficTime20:00 TimePowerConsumptionFull power limitLow power limit
647 SAVING ENERGY WITH YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.17.3 Manually Switching Off Services to Reduce PowerECO buttonIf you are not using the wireless access point of your Technicolor Gateway, you might consider to disable the wireless access point permanently. This allows you to further reduce the power consumption.To turn the wireless interface:Off, press the ECO ( ) button until the Wireless LED is off.On, press the ECO ( ) button until the Wireless LED is on.Zero power consumptionIf you will not be using your Technicolor Gateway for a longer time (for example: you are going on holiday), you should consider to turn off the Technicolor Gateway. This way no energy will be consumed at all.However, be aware that if you turn off the Technicolor Gateway, all services provided by the Technicolor Gateway that require access to the Internet will not be available. For example:No VoIP calls can be made/receivedYou will no longer be able to make or receive phone calls over the Internet. Your phone calls will automatically be done via the traditional phone network (if available).No Digital TV is providedIf your set-top box is connected to your Technicolor Gateway, it will no longer be able to connect to the Internet, hence not be able to service your TV set.
658 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.18 Sharing Content on your Technicolor GatewayIntroductionThe Technicolor Gateway allows you to share the content stored on your USB storage device with other users on your network or even access this shared content from the Internet.FeaturesThe Technicolor Gateway supports USB 2.0The following file systems are supported:NTFS (optional)FAT32FAT16HFS+ (optional)EXT2/EXT3 (optional)You can connect up to five USB storage devices (via a USB hub).Each USB storage device can have up to 10 partitions. If your device has more partitions the extra partitions will be ignored.Content Sharing ServersThe Technicolor Gateway offers three types of services to share your content. The following table gives a you a brief overview of the main functions:Network File Server UPnP AV Media Server FTP ServerFunction Store and access your data on your local network.Make media files available for UPnP AV capable devices like Media players, Set-Top boxes from your local network.Store and access your data from the Internet.Access Read and write Read-only Read and writeAccessible from Local network Local network Internet and Local networkType of content shared All files from all partitions and disks that are connected.Media files (music, movies and pictures) from all partitions and disks that are connected.All files that are stored in the Shared folder of the managed partition.For more information, see...“8.1 The Network File Server” on page 67“8.2 The UPnP AV Media Server” on page 70“8.3 The FTP Server” on page 74
668 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.1ConfigurationAll servers are enabled by default. The only thing that you need to do is to plug your USB memory stick or external hard disk in (one of) the USB port(s) of your Technicolor Gateway.By using a USB hub, you can connect up to five USB mass storage devices to the Technicolor Gateway.Do not remove your USB storage device without stopping it first, otherwise data might be lost! For more information, see “8.5 Safely Removing your USB Storage Device” on page 78.
678 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.18.1 The Network File ServerIntroductionThe Network Server allows you to share the content on your USB storage device(s) with other devices that are connected to your local network (mostly computers).These devices have read and write access to this USB device(s).ConfigurationThe Network File Server is enabled by default and ready for use.To change the default settings, proceed as follows:1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2On the Tools menu, click Content Sharing.3In the Navigation bar, click Configure.4Under Network File Server (Windows Networking), you can change the following settings:Server Name:Enter the name that you want to use to access the Technicolor Gateway.Server Description:Add a short description for what kind of data is stored on the USB storage device.Workgroup:Enter the same workgroup as used by your computer(s).Server Enabled:Select this option to enable the Network File Server5Click Apply.6All users connected to the Technicolor Gateway can now access the data on stored your USB storage device.7If you want to limit the number of folders that can be accessed, continue with “8.4 Managing your Shared Content” on page 76.Accessing the shared content on WindowsProceed as follows:1Open Windows Explorer.2In the address bar, type two backslashes followed by the name that you entered in the Server Name box (default: \\Technicolor).If you did not provide a server name, type \\192.168.1.253.
688 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.13An Explorer windows appears. The storage devices that are attached to your Technicolor Gateway are listed as folders.If the storage device has multiple partitions an index number will be added at the end (for example: Disk_a1 and Disk_a2).If multiple storage devices are inserted the first one is listed as Disk_a1, the second one as Disk_b1, and so on.If the partition is a managed partition, only the Media and Shared folders of the managed partition are displayed:For more information on managed partitions, see “8.4 Managing your Shared Content” on page 76.4If you plan to frequently use this folder, it might be useful to map this folder as a network drive. For more information, see the help of your operating system.Accessing the shared content on MacProceed as follows:1On the Go menu, click Connect To Server.2The Connect To Server window appears.In the Server Address box, type smb://<server name>, where <server name> is the Server Name you assigned to your USB storage device (default: smb://Technicolor).If you did not provide a server name, type smb://192.168.1.253.
698 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.13The following window appears:Select Guest and click Connect.4If prompted, select the partition that you want to open and click OK:5Your USB storage device is now mounted and is displayed on your desktop.
708 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.18.2 The UPnP AV Media ServerIntroductionYour Technicolor Gateway has a built-in DLNA-certified UPnP AV media server. This section describes how to use and configure this media server.UPnP AVUPnP AV (AV stands for Audio and Video) is a protocol especially designed to share media files on your local network.DLNA-certifiedThe Digital Living Network Alliance (DLNA) is an organisation that imposes requirements to ensure the interoperatability of your media devices and standardize the communication between them.Buying a DLNA-certified device like the Technicolor Gateway guarantees you that it will seamlessly integrate with your other DLNA-certified devices.To allow you to access your media in a quick and easy way, the Technicolor Gateway scans your storage device for meta data information (for example, title, artist, album) and stores it in a database. When you are looking for a file, the Technicolor Gateway can simply query the database instead of having to go through all the files.UPnP AV network componentsA UPnP AV network consists of the following components:The UPnP AV server is directly connected to your media files and makes them available on the network. In your network the Technicolor Gateway will fulfil this role.The UPnP AV client is a software application or hardware device that allows you to play or view the media files provided by your UPnP AV media server.This database will only be created if the following conditions are met:Your disk or partition must have at least 250MB of free spaceYour disk or partition must not be read-only.
718 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.18.2.1 Configuring the UPnP AV Media ServerIntroductionThe Network File Server is enabled by default and ready to use.Enabling/disabling the UPnP AV Media ServerProceed as follows:1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2On the Tools menu, click Content Sharing.3In the Navigation bar, click Configure.4Under UPnP AV Media Server, click Server Enabled.5Click Apply.Media DatabaseWhen you plug in your USB storage device, the Technicolor Gateway will automatically start building the media database. This database contains all meta data of the media files stored on your USB storage device.To view the status of the media database:1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2On the Tools menu, click Content Sharing.3In the Navigation bar, click Configure.4Under UPnP AV Media Server, you can find the Database Status.5If you want to rebuild the database, click Rebuild.
728 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.18.2.2 Using the UPnP AV Media ServerIntroductionThe UPnP AV Media Server lists all audio, video and picture files located on the connected USB storage device. All UPnP AV renderers (for example, a DLNA-certified Set-Top box) that are connected to your network are able to view this list and play or view items from this list.On your UPnP AV renderer, the Technicolor Gateway’s UPnP AV media server will be listed as Technicolor TGXXX. Below you can find a screenshot taken on a smartphone with a UPnP AV client.Via this entry, you can browse to your media files.Windows 7Windows 7 has native support for UPnP AV. It automatically detects UPnP AV and makes your media files available for playback on your Windows Media Player.Proceed as follows:1On the Windows Start menu, click Network.
738 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.12The Network window appears:Under Media Devices you will find the Technicolor Gateway’s UPnP AV Media Server (displayed as Technicolor TGXXX).3Double-click the Technicolor Gateway’s UPnP AV Media Server to access your media files.4 Windows Media Player starts up.Your Technicolor Gateway’s UPnP AV Media Server is listed on the left. This entry allows you to browse to your media files.
748 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.18.3 The FTP ServerIntroductionThe Technicolor Gateway allows you to access your shared content by FTP. This can be useful if you want to be able to access your shared content from the Internet.Via FTP you can download and upload all types of files both from your local network and the Internet.Setting up the FTP serverProceed as follows:1Protect your account with a password.2Enable the FTP Server and select the managed partition.Protect your account with a passwordIf you did not yet configure your login to the Technicolor Gateway GUI with a password:1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2On the Toolbox menu, click User Management.3In the Pick a task list, click Change my password.4Leave the Old Password box empty.5Type your new password both in the New Password box and Confirm New Password box.Enable the FTP Server and select the managed partitionProceed as follows:1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2On the Tools menu, click Content Sharing.3In the Navigation bar, click Configure.4Under FTP Server, click Server Enabled.5Under List of connected disks, click the radio button next to the partition to make it managed.6The Technicolor Gateway now creates a Media and Shared folder on the selected partition. The Shared folder will be used as root location for FTP sessions.7Click Apply.
758 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.1ResultThe Shared folder and its subfolders are now accessible using FTP. The other folders are not accessible via FTP.If you are connected to the Internet, the link to the FTP server is displayed under FTP Server:On the Technicolor Gateway network, you can also access the FTP server using its local address (192.168.1.253).Additional configurationBecause most service providers use dynamic IP addresses, the IP address of your Internet connection may change frequently. This implies that the link to the FTP server will also change every time the public IP changes. With Dynamic DNS, you can assign a host name to the IP address (for example mygateway.dyndns.org). For more information, see “9.3 Dynamic DNS” on page 89.
768 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.18.4 Managing your Shared ContentManaged PartitionIf you select your drive or partition as managed partition, users only have access to the following folders:MediaSharedAll other folders will be hidden from the user. These hidden folders are still on the USB storage device, but you can not access them. If you connected more than one USB storage device, those devices will also be hidden.Media folderUse the Media folder to share your audio, video and picture files. This folder can only be accessed via the following servers:The Network File ServerFor more information, see “8.1 The Network File Server”.UPnP AV Media Server.For more information, see “8.2 The UPnP AV Media Server”.Shared folderThe Shared folder is a folder to share files both on the local network and the Internet. This folder can only be accessed via the following server:The Network File ServerFor more information, see “8.1 The Network File Server”.FTP ServerFor more information, see “8.3 The FTP Server”.Ummanaged vs. managedThe following table compares the two modes:Setting up the managed partitionProceed as follows:1Browse to the Technicolor Gateway GUI.2On the Tools menu, click Content Sharing.3In the Navigation bar, click Configure.4Under List of connected disks, click the radio button next to the partition you want to configure as Managed Partition.If your partition is managed, the UPnP AV server will only use the media files that are located in the Media folder.The FTP Server can only be used with a managed partition.Access via Accessible foldersUnmanaged ManagedNetwork File Server All Media and Shared folder.UPnP AV Media Server All Media folder.FTP Server Not available in this mode. Shared folder.
778 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.15Click Apply.ResultThe Technicolor Gateway creates following folders:Media:Use this folder to share your media files with others users on your network. You can store your media files in following subfolders:MoviesMusicPicturesShared:Use this folder to share your other data with other users on your network. Optionally, users can also access this folder using FTP. For more information, see “8.3 The FTP Server” on page 74.If the above folders already exist, the existing folders are used.
788 SHARING CONTENT ON YOUR TECHNICOLOR GATEWAYDMS-CTC-20101206-0033 v0.18.5 Safely Removing your USB Storage DeviceIntroductionIf you just unplug your USB storage device from the Technicolor Gateway you may loose your data. To avoid this you must first stop your USB storage device.Stopping your USB storage deviceProceed as follows1Browse to the Technicolor Gateway GUI.2On the Toolbox menu, click Content Sharing.3In the Navigation bar, click Configure.4Click Stop.5Unplug your USB storage device from the Technicolor Gateway.
799 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.19 Technicolor Gateway Network ServicesIn this chapterIn this chapter we will take a closer look at following features:Feature availabilityDepending on the configuration offered by your service provider, some features may not be available on your Technicolor Gateway. For more information, contact your service provider.To p i c Page9.1 UPnP 809.2 Assigning a service (HTTP, FTP,...) to a Computer 879.3 Dynamic DNS 89
809 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.19.1 UPnPIntroductionUPnP is designed to automate the installation and configuration of a (small) network as much as possible. This means that UPnP-capable devices can join and leave a network without any effort of a network administrator.Supported Operating SystemsThe following operating systems support UPnP:Windows 7Windows VistaWindows XPUPnP and the Technicolor GatewayUPnP offers you the following functions:You can access the Technicolor Gateway GUI without having to remember the address of the Technicolor Gateway. For more information, see “9.1.1 Accessing Your Technicolor Gateway via UPnP” on page 81.If you are using a PPP connection to connect to the Internet, you can enable/disable your Internet connection without having to open the Technicolor Gateway GUI.For more information, see “9.1.2 Managing your Internet connection via UPnP” on page 82.You do not have to manually create port mappings to run services on a computer. The automatic port configuration mechanism for UPnP-enabled games and applications will do this for you. If the application is UPnP-enabled, UPnP will create these entries automatically. For more information, see “9.2 Assigning a service (HTTP, FTP,...) to a Computer” on page 87.If your computer is running Windows XP, you first have to install the UPnP component. For more information, see “9.1.4 Installing UPnP on Windows XP” on page 85.
819 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.19.1.1 Accessing Your Technicolor Gateway via UPnPWindows 7/VistaIf you computer runs Windows 7/Vista:1On the Windows Start menu, click Network.2The Network window appears:3Right-click your Technicolor Gateway (displayed as Technicolor TGXXX) and click View device web page.4The Technicolor Gateway GUI appears.Windows XPIf you computer runs Windows XP:1Go to My Network Places.2The My Network Places window appears:3Double-click your Technicolor Gateway (displayed as Technicolor TGXXX).4The Technicolor Gateway GUI appears.
829 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.19.1.2 Managing your Internet connection via UPnPApplicabilityThis section only applicable if you are using a PPP connection to the Internet.Windows 7/VistaIf you computer runs Windows 7/Vista:1On the Windows Start menu, click Network.2The Network window appears:3Right-click your Technicolor Gateway (displayed as Technicolor TGXXX).4If you are currently:Connected to the Internet, click Disable to disconnect from the Internet.Not connected to the Internet, click Enable to connect to the Internet.Windows XPProceed as follows:1On the Windows Start menu, click (Settings >) Control Panel.2The Control Panel window appears.Click (Network and Internet Connections) > Internet Connections.
839 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.13The Network Connections window appears;4If you right-click the Internet Connection icon, you can connect/disconnect your connection to the Internet.Disabling this featureTo prevent that users can connect/disconnect you can enable Extended Security. This feature is enabled by default.For more information, see “9.1.3 Configuring UPnP on the Technicolor Gateway” on page 84.
849 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.19.1.3 Configuring UPnP on the Technicolor GatewayIntroductionOn the Technicolor Gateway GUI you can:Enable/Disable UPnP.Enable/Disable Extended Security.Enable/Disable UPnPProceed as follows:1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2On the Toolbox menu, click Game & Application Sharing.3Under Universal Plug and Play:Select the Use UPnP check box, to enable UPnP.Clear the Use UPnP check box, to disable UPnP.4Click Apply.Extended SecurityIf Extended Security is enabled, only limited UPnP operation between the host and the Technicolor Gateway is allowed:A local host is not allowed to connect/disconnect the Technicolor Gateway Internet connection. You can then only connect/disconnect the Internet connection via the Technicolor Gateway GUIAddress translation mappings can only be added or changed via UPnP for the host on which the UPnP application is running.Enable/Disable Extended SecurityProceed as follows:1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2On the Toolbox menu, click Game & Application Sharing.3Under Universal Plug and Play, select Use Extended Security.4Click Apply.
859 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.19.1.4 Installing UPnP on Windows XPAdding UPnPIf you are running Microsoft Windows XP, it is recommended to add the UPnP component to your system.Proceed as follows:1In the Start menu, click (Settings >) Control Panel.2The Control Panel window appears.Click Add or Remove Programs.3The Add or Remove Programs window appears.Click Add/Remove Windows Components.4The Windows Components Wizard appears:In the Components list, select Networking Services and click Details5The Networking Services window appears: Select Universal Plug and Play or UPnP User Interface and click OK.6Click Next to start the installation and follow the instructions in the Windows Components Wizard.7At the end of the procedure the wizard informs you that the installation was successful. Click Finish to quit.Adding IGD Discovery and ControlYour Windows XP system is able to discover and control Internet Gateway Devices (IGD), like the Technicolor Gateway on your local network. Therefore, it is recommended to add the IGD Discovery and Control client to your system.Proceed as follows:1On the Windows taskbar, click Start.
869 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.12Select (Settings >) Control Panel > Add or Remove Programs.3In the Add or Remove Programs window, click Add/Remove Windows Components.4The Windows Components Wizard appears:Select Networking Services in the Components list and click Details.5The Networking Services window appears:Select Internet Gateway Device Discovery and Control Client and click OK.6Click Next to start the installation and follow the instructions in the Windows Components Wizard.7At the end of the procedure, the wizard informs you that the installation was successful. Click Finish to quit.
879 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.19.2 Assigning a service (HTTP, FTP,...) to a ComputerIntroductionThe Technicolor Gateway allows you to use one Internet connection for multiple computers. This means that all your computers share one public IP address, as if only one computer were connected to the outside world.IssueWhen the Technicolor Gateway receives an incoming message, the Technicolor Gateway has to decide to which computer it has to send this message.If the incoming message is a response to an outgoing message originating from one of your computers, the Technicolor Gateway sends the incoming message to this computer.If your are running a server or an application that acts as a server (for example a HTTP server, Internet game), the initial message will come from the Internet and the Technicolor Gateway has no information to decide to which computer it should forward the incoming message.SolutionTo avoid this problem you can do either of the following:Enable UPnP.Assign a game or application to a local networking device.UPnPUPnP is a technology that enables seamless operation of a wide range of games and messaging applications. Your computer will use UPnP to communicate to the Technicolor Gateway which services are running on the computer.For example, when you start a UPnP-enabled application on your computer, it will automatically create the necessary port mappings on this computer and on the Technicolor Gateway.For more information on UPnP, see “9.1 UPnP” on page 80.InternetInternet?
889 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.1Assign a game or application to a local networking deviceIf you assign a game or application to a local networking device, you will basically tell the Technicolor Gateway that if it receives requests for a specific game or application, it has to forward these messages to a specific computer.Proceed as follows to do so:1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2On the Toolbox menu, click Game & Application Sharing.3In the Pick a task list, click Assign a game or application to a local network device.4In the Game or application list, click the service you want to run on the computer. For example, HTTP Server (World Wide Web).5In the Device list, select the computer to which you want to assign the service. Your computer will be listed with its computer name.6All incoming requests for the selected service will now be directed to the selected device. The Technicolor Gateway will also configure its firewall to allow this service.If the service is not available in the list, click Create a new game or application in the Pick a task list. For more information, click Help on the Technicolor Gateway GUI.
899 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.19.3 Dynamic DNSIntroductionThe Dynamic DNS service allows you to assign a dynamic DNS host name (for example mywebpage.dyndns.org) to a broadband connection even if it is using a dynamic IP address. As soon as the device gets a new IP address, the dynamic DNS server updates its entry to the new IP address.What you needBefore you can configure Dynamic DNS, you first have to create an account at a Dynamic DNS service provider. For example:www.dyndns.orgwww.no-ip.comwww.dtdns.comProcedureProceed as follows: 1Browse to the Technicolor Gateway GUI.For more information, see “Accessing the Technicolor Gateway GUI” on page 35.2On the Toolbox menu, click Dynamic DNS.3On the Navigation bar, click Configure.4Select the Enabled check box.5If necessary, select the broadband connection to which you want to assign the Dynamic DNS host name in the Interface list.6Type the user name and password of your Dynamic DNS service account in the corresponding fields.7In the Service list, click the name of your Dynamic DNS service provider.8In the Host box, type the host name that you got from the Dynamic DNS service provider (for example mywebpage.dyndns.org).9Click Apply.
909 TECHNICOLOR GATEWAY NETWORK SERVICESDMS-CTC-20101206-0033 v0.1
9110 INTERNET SECURITYDMS-CTC-20101206-0033 v0.110 Internet SecurityOverviewThe Technicolor Gateway offers various options to secure your network and network connection:To p i c Page10.1 Parental Control 9210.2 Firewall 97
9210 INTERNET SECURITYDMS-CTC-20101206-0033 v0.110.1 Parental ControlIntroductionThe Technicolor Gateway allows you to deny access to specific web sites.Access Denied pageWhen a user tries to access a page that is being blocked, the following page is displayed:Address-based filteringWith address-based filtering (or URL-filtering) you can block web sites based on their address (for example www.porn.com).Content-based filteringAs you know, the Internet consists of a large number of web sites, and that number still increases every day. This makes it almost impossible to keep the list of addresses up-to-date.To solve this problem Technicolor Gateway introduced content-based filtering.With content-based filtering you can block web sites based on their content category (for example pornography) instead of their URL. This way, you only need to select the appropriate categories and the content category server takes care of the rest. This content category server is updated at regular intervals.Combining the two filtersAddress-based filtering has priority over content-based filtering. This means that when you are blocking a specific category, you can still access a specific address provided you create a rule to allow access to that URL.For example, if you are blocking content from the Finance / Investment category, you can create a rule to make an exception for netbanking.mybank.com.Activating content-based filteringBefore you can use content-based filtering you must first activate it by purchasing a license key at your service provider or by activating the 30-day trial.Proceed as follows:1Browse to the Technicolor Gateway GUI.2On the Toolbox menu, click Parental Control.3In the Pick a task list, click Activate Web Filtering License.4The Web Filtering Activation page appears. Under License Type, select:30-days evaluation if you first want evaluate this feature.Standard if you have already purchased a license key. The License key box appears as soon as you select this option. Type the license key that you received from your service provider in this box.5Click Apply.
9310 INTERNET SECURITYDMS-CTC-20101206-0033 v0.1Option 1: content-based filter (combined with the address-based filter)If you want to use the content-based filtering:1Browse to the Technicolor Gateway GUI.2On the Toolbox menu, click Parental Control.3On the Navigation bar, click Configure.4Make sure that the Use Content-Based Filter check box is selected.5Configure the content-based filter. For more information, see “10.1.1 Configuring Content-based Filtering” on page 94.6If you want to make exceptions for specific web sites, add the necessary rules in the address-based filter. For more information, see “10.1.2 Adding Rules for Address-Based Filtering” on page 95.Option 2: address-based filter onlyTake this option if content filtering is not available on your Technicolor Gateway or you don’t want to use it.To configure address-based filtering:1Browse to the Technicolor Gateway GUI.2On the Toolbox menu, click Parental Control.3On the Navigation bar, click Configure.4Make sure that the Use Address-Based Filter check box is selected.5In the Action for Unknown Sites, select:Allow as the default rule if you want to allow access to all web sites and manually specify which web sites may not be accessed.Block as the default rule if you want to deny access to all web sites and manually specify a number of web sites that may be accessed.6Click Apply.7If you want to make exceptions for specific web sites, add the necessary rules in the address-based filter.For more information, see “10.1.2 Adding Rules for Address-Based Filtering” on page 95.
9410 INTERNET SECURITYDMS-CTC-20101206-0033 v0.110.1.1 Configuring Content-based FilteringRequirementsContent-based filtering must be activated on your Technicolor Gateway.For more information, see “Activating content-based filtering” on page 92.Accessing the configuration pageProceed as follows:1Browse to the Technicolor Gateway GUI.2On the Toolbox menu, click Parental Control.3On the Navigation bar, click Configure.4Under Content-Based Filtering you can change the settings of the content-based filter.ConfigurationUnder Content-Based Filtering:1Select Use Content-Based Filter check box (if needed).2In the Action for uncategorised sites list, select a default action for sites that have not yet been categorised.3Under Content Level, select the content level you want to use.If you want a more detailed view of the content that will be blocked for this level, click the Edit link next to the content level.If needed, you can change the Name, Description and Configuration of the content level.4Click Apply after you have made your changes.Creating your own content levelProceed as follows:1In the Pick a task list, click Create a new content level.2Enter a Name and Description for your content level and click Next.3Under Configuration, select:Clone Existing Level if you want to start from an existing level. You can now select the level that you want to clone.White list if you want to block everything and select which content should be allowed.Black list if you want to allow everything and select which content should be blocked.Click Next.4Under Configuration:Select the check boxes of the categories/groups you want to allow.Clear the check boxes of the categories/groups you want to block.5Click Apply.6Configure the content-based filter with the new level. For more information, see “Configuration” on page 94.
9510 INTERNET SECURITYDMS-CTC-20101206-0033 v0.110.1.2 Adding Rules for Address-Based FilteringIntroductionAddress-based filtering has a higher priority than content-based filtering. This means that when you are blocking a specific category, you can still access a specific site if you allow it in the address-based filter.ExampleIf you block content from the Finance / Investment category and allow access to netbanking.mybank.com, netbanking.mybank.com will still be accessible.OptionsWith the address-based filter you can:Deny access to a specific web site.Allow access to a specific web site.Redirect a web site.Redirect all web sites.Deny access to a specific web siteProceed as follows:1Browse to the Technicolor Gateway GUI.2On the Toolbox menu, click Parental Control.3Make sure the Use Address-Based Filter check box is selected.4Type the URL of the Web site you want to block (for example “mail.provider.com”) in the Web Site box.5In the Action list, click Block.6Click Add.Allow access to a specific web siteProceed as follows:1Browse to the Technicolor Gateway GUI.2On the Toolbox menu, click Parental Control.3Make sure the Use Address-Based Filter check box is selected.4Type the URL of the Web site you want to allow (for example “netbanking.bank.com”) in the Web Site box.5In the Action list, click Allow.6Click Add.Redirect a web siteProceed as follows:1Browse to the Technicolor Gateway GUI.2On the Toolbox menu, click Parental Control.3Make sure the Use Address-Based Filter check box is selected.4Type the URL of the Web site you want to redirect (for example “cracks.am”) in the Web Site box.5Click Redirect in the Action list.
9610 INTERNET SECURITYDMS-CTC-20101206-0033 v0.16Type the URL of the Web site you want to redirect to (for example “mycompany.com/internetpolicy.htm”) in the Redirect box.7Click Add.Redirect all web sitesProceed as follows:1Browse to the Technicolor Gateway GUI.2On the Toolbox menu, click Parental Control.3Make sure the Use Address-Based Filter check box is selected.4Type “*” in the Web Site box.5Click Redirect in the Action list.6Type the URL of the Web site you want to redirect to (for example “mycompany.com/internetpolicy.htm”) in the Redirect box.7Click Add.
9710 INTERNET SECURITYDMS-CTC-20101206-0033 v0.110.2 FirewallIntroductionThe Technicolor Gateway comes with an integrated firewall that helps you protect your network from attacks from the Internet. This firewall has a number of predefined levels to allow you to adjusted the firewall to your needs.The Firewall is disabled by default. This means that all traffic passing through the Technicolor Gateway (from and to the Internet) is allowed.Predefined security levelsThe Technicolor Gateway has a number of predefined security levels. The following levels are available:BlockAll: All traffic from and to the Internet is blocked. Game and Application Sharing is not allowed by the firewall.Standard: All outgoing connections are allowed. All incoming connections are blocked, except for inbound connections assigned to a local host via Game and Application Sharing.Disabled: All in- and outgoing traffic is allowed to pass through your Technicolor Gateway, including Game and Application Sharing.This is the default firewall level.Changing the security levelProceed as follows:1Browse to the Technicolor Gateway GUI.2On the Toolbox menu, click Firewall.3The Firewall page appears. In the upper-right corner, click Configure.4Under Security Settings, select the security level of your choice and click Apply.Creating your own security levelProceed as follows:1 In the Toolbox menu click Firewall.2 In the Firewall section, go to the Configure page.3 In the Pick a task list, click Create a new Security Level.4 In the Name box, type a name for the new security level and select an existing security level to clone from.5Click Apply.6A page with the firewall settings of your newly created security level appears. Click Edit.7 Enter the following information:The Name of the firewall rule.Although BlockAll will block all connections, some mandatory types of traffic such as DNS will still be relayed between LAN and WAN by the Technicolor Gateway.Once you create a security level, you can not delete it anymore. It will always available in the list of available security levels.
9810 INTERNET SECURITYDMS-CTC-20101206-0033 v0.1The Source Interface and IP Address (range).Or you can type a User-defined IP address (range).The Destination Interface and IP Address (range)Or you can type a User-defined IP address (range).The Service type of the traffic; this can be a protocol (DNS, SMTP,...) or a specific Technicolor Gateway system service.8 Select an Action that should be done on traffic for which the firewall rules applies:Accept: to allow the traffic to passDeny: to drop the traffic (without notification)Count: to let the traffic pass, but count it (Hits)9Click Apply.Use Any as IP address in case all traffic for the interface should be parsed.Use Any as IP address in case all traffic for the interface should be parsed.
9911 SUPPORTDMS-CTC-20101206-0033 v0.111 SupportIntroductionThis chapter suggests solutions for issues that you may encounter while installing, configuring or using your Technicolor Gateway.If the suggestions do not resolve the problem, look at the support pages on www.technicolor.com or contact your service provider.To p i c sThis chapter describes the following topics:To p i c Page11.1 Setup Troubleshooting 10011.2 General Technicolor Gateway Troubleshooting 10111.3 Wired Connection Troubleshooting 10311.4 Wireless Connection Troubleshooting 10311.5 Voice over IP Troubleshooting 10411.6 Reset to Factory Defaults 105
10011 SUPPORTDMS-CTC-20101206-0033 v0.111.1 Setup TroubleshootingIntroductionIf you have trouble to install your Technicolor Gateway with the Setup CD, try the suggested solutions in this section.The Setup CD does not start automaticallyIf your computer runs:Microsoft Windows 7 and Vista:aClick the Windows Start button.bIn the Search programs and files box, type the following path: D:\Setup.exe, where D stands for the drive letter of your CD- or DVD-ROM drive.cPress ENTER.Microsoft Windows XP:aClick the Windows Start button.bClick Run.cIn the Open field, type the following path: D:\Setup.exe, where D stands for the drive letter of your CD- or DVD-ROM drive.Mac OS X:aOn your desktop, double-click the CD icon.bDouble-click Menu.Your Technicolor Gateway has not been foundIf you see this error during setup, make sure that:The Technicolor Gateway is turned on and fully initialized.Your computer has a valid IP address, that is any address but 0.0.0.0. For more information, consult the help of your operating system.No dedicated firewall device or router is placed between your computer and the Technicolor Gateway.No personal network security software (for example firewall software) is running on your computer.Your computer is correctly connected to the Technicolor Gateway.
10111 SUPPORTDMS-CTC-20101206-0033 v0.111.2 General Technicolor Gateway TroubleshootingNone of the LEDs light up (Technicolor Gateway does not work)Make sure that:The Technicolor Gateway is plugged into a power socket outlet.You are using the correct power supply for your Technicolor Gateway device.The Technicolor Gateway is turned on via the push button or rocker switch on the back panel.The Broadband LED does not light up or is blinkingMake sure that:The DSL cable is correctly connected. For more information, see “3.1 Connecting the Technicolor Gateway to your Service Provider’s Network”.The DSL service is enabled on your telephone line. For more information, contact your Internet Service Provider.The Internet LED does not light upIf you must authenticate to connect to the Internet, make sure that your user name and password are correct.Proceed as follows:1Browse to the Technicolor Gateway GUI.2On the Broadband menu, click Internet Services.3Under Internet, click View More.4Check your user name 5Re-enter your password.6Click Connect.Technicolor Gateway unreachableIf you can not access your Technicolor Gateway via your web browser or the Setup wizard, you might consider a hardware reset as described in “11.6 Reset to Factory Defaults” on page 105.The power requirements for your Technicolor Gateway are clearly indicated on the identification label of the Technicolor Gateway. Only use the power adaptor supplied with your Technicolor Gateway.
10211 SUPPORTDMS-CTC-20101206-0033 v0.111.3 Wired Connection TroubleshootingEthernet LED does not light upMake sure that:The Ethernet cable is securely connected to the Ethernet port on your Technicolor Gateway and your computer.You are using the correct cable type for your Ethernet equipment, that is at least UTP CAT5 with RJ-45 connectors.
10311 SUPPORTDMS-CTC-20101206-0033 v0.111.4 Wireless Connection TroubleshootingNo Wireless ConnectivityTry the following:Make sure that the wireless client adapter is enabled (message like “radio on”).Make sure that the wireless client is configured for the correct wireless settings (Network Name, security settings).If the signal is low or not available, try to reposition the Technicolor Gateway or (if available) redirect the antenna(s) of the Technicolor Gateway for optimal performance.Change the wireless channel.Poor Wireless Connectivity or RangeTry the following:Check the signal strength, indicated by the wireless client manager. If the signal is low, try to reposition the Technicolor Gateway or (if available) redirect the antenna(s) of the Technicolor Gateway for optimal performance.Change the wireless channel.Use WPA(2)-PSK as encryption.For more information, see “5.3 Securing Your Wireless Connection” on page 45.Change the wireless channelProceed as follows:1Browse to the Technicolor Gateway GUI.2Under Home Network, click Wireless3The Wireless Access Point page appears.4In the Navigation bar, click Configure.5Under Configuration, select the channel of your choice in the Channel Selection list.6Click Apply.Can not connect via WPSIf you are having trouble connecting your wireless client via WPS, try to configure it manually. For more information, see “5.2 Connecting Your Wireless Client without WPS” on page 44.
10411 SUPPORTDMS-CTC-20101206-0033 v0.111.5 Voice over IP TroubleshootingIntroductionIf you cannot make or receive any phone calls via your Technicolor Gateway, try the suggestions in the following sections. Calling over VoIPIf you have problems calling via VoIP, check whether:Your phone is correctly connected to the Technicolor Gateway.Your phone is working on the traditional telephone network (PSTN):Connect your phone directly to the telephone wall outlet.Try to make a phone call.Your phone number, user name, and password are configured correctly.The registrar’s and proxy server’s IP address and port number are configured correctly.The Power, Broadband and Voice LEDs are on.Calling over the traditional telephone network (PSTN)If you have problems calling via the traditional telephone network, check whether:Your phone is correctly connected to the Technicolor Gateway.Your phone is working on the PSTN network:Connect your phone directly to PSTN.Try to make a phone call.The Forced FXO service is activated, this means that your service provider may request you to dial an extra prefix for making calls via PSTN.Problems with Telephony ServicesIf you have a problem with a service, check whether the service is activated. For more information, see “6.3.1 Activating a Telephony Service on your Technicolor Gateway” on page 55.This is not possible on the VoIP-only variants. For more information, see “Applicability” on page 49.This is not possible on the VoIP-only variants. For more information, see “Applicability” on page 49.If the Technicolor Gateway is turned off, phone calls are always routed over PSTN.
10511 SUPPORTDMS-CTC-20101206-0033 v0.111.6 Reset to Factory DefaultsResetting your Technicolor GatewayIf at some point you can no longer connect to the Technicolor Gateway or you want to make a fresh install, it may be useful to perform a reset to factory defaults.WarningA reset to factory default settings deletes all configuration changes you made. Therefore, after the reset a reconfiguration of your Technicolor Gateway will be needed.Also your wireless clients will have to be re-associated, as described in “5 The Technicolor Gateway Wireless Access Point” on page 41.MethodsYou can choose between:Resetting the Technicolor Gateway via the Technicolor Gateway GUIReset the Technicolor Gateway via the Reset buttonResetting the Technicolor Gateway via the Technicolor Gateway GUIProceed as follows:1Browse to the Technicolor Gateway GUI.2On the Technicolor Gateway menu, click Configuration.3In the Pick a task list, click Reset my Technicolor Gateway.4The Technicolor Gateway restores the initial configuration and restarts.5The Technicolor Gateway returns to the Technicolor Gateway home page (unless the IP address of your computer is not in the same subnet as the default IP address of the Technicolor Gateway, being 192.168.1.254).Reset the Technicolor Gateway via the Reset buttonProceed as follows:1Make sure the Technicolor Gateway is turned on.2Push the Reset button for 7 seconds and the release it.
10611 SUPPORTDMS-CTC-20101206-0033 v0.13The Technicolor Gateway restarts.Your system administrator may have disabled the physical reset button of the Technicolor Gateway. In this case, a hardware reset to defaults is not possible.
Copyright 2011 Technicolor. All rights reserved. All tradenames referenced are service marks, trademarks, or registered trademarks of their respective companies. Specifications subject to change without notice.DMS-CTC-20101206-0033 v0.1TECHNICOLOR DELIVERY TECHNOLOGIES BELGIUM NVPrins Boudewijnlaan 472650 EdegemBelgiumwww.technicolor.com

Navigation menu