Technicolor Delivery Technologies Belgium TG585V7 ADSL Modem User Manual ST585v6 InstallSetup en

Technicolor Delivery Technologies Belgium ADSL Modem ST585v6 InstallSetup en

Contents

Manual 1

PowerWLANEthernetDSLInternetThomson ST585(v6)Installation and Setup Guide
Thomson ST585(v6)Installation and Setup Guide
CopyrightCopyright ©1999-2007 Thomson. All rights reserved. Distribution and copying of this document, use and communication of its contents is not permitted without written authorization from Thomson. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by Thomson. Thomson assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.Thomson Telecom BelgiumPrins Boudewijnlaan, 47 B-2650 Edegem Belgium http://www.thomson-broadband.comTrademarksThe following trademarks are used in this document:>DECT is a trademark of ETSI.>Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.>Ethernet™ is a trademark of Xerox Corporation.>Wi-Fi® and the Wi-Fi logo are registered trademarks of the Wi-Fi Alliance. "Wi-Fi CERTIFIED", "Wi-Fi ZONE", "Wi-Fi Alli-ance", their respective logos and "Wi-Fi Protected Access" are trademarks of the Wi-Fi Alliance.>UPnP™ is a certification mark of the UPnP™ Implementers Corporation.>Microsoft®, MS-DOS®, Windows® and Windows NT® are either registered trademarks or trademarks of Microsoft Corpo-ration in the United States and/or other countries.>Apple® and Mac OS® are registered trademarks of Apple Computer, Incorporated, registered in the United States and other countries.>UNIX® is a registered trademark of UNIX System Laboratories, Incorporated.>Adobe®, the Adobe logo, Acrobat and Acrobat Reader are trademarks or registered trademarks of Adobe Systems, Incor-porated, registered in the United States and/or other countries.Other brands and product names may be trademarks or registered trademarks of their respective holders.Document InformationStatus: v1.0 (January 2007)Reference: E-DOC-CTC-20060911-0041-Short Title: Installation and Setup Guide ST585(v6) R6.2
E-DOC-CTC-20060911-0041- v1.0 iContentsAbout this Installation and Setup Guide..................................  11 Introducing the Thomson Gateway........................................... 32 Basic Installation.......................................................................... 52.1 Mounting your Thomson Gateway .................................................................. 62.2 Installing your Thomson Gateway .................................................................. 72.2.1 Guided Installation ................................................................................................................................. 82.2.2 Manual Installation............................................................................................................................... 162.3 The Setup CD ................................................................................................ 182.4 Thomson Gateway Connection Essentials .................................................... 202.5 Connections Overview and Powering ........................................................... 212.5.1 Wireless Setup...................................................................................................................................... 222.6 Basic Security ............................................................................................... 243 Web-Based User Interface ........................................................ 274 Troubleshooting ........................................................................ 294.1 Checking the Hardware................................................................................. 304.2 LED Diagnostics ............................................................................................ 314.3 Web Diagnostics ........................................................................................... 334.4 Thomson Gateway Setup CD Troubleshooting ............................................. 354.5 Windows Zero Configuration ........................................................................ 384.6 Easy Setup Troubleshooting ......................................................................... 404.7 Reset to Factory Defaults ............................................................................. 41
E-DOC-CTC-20060911-0041- v1.0Contentsii
E-DOC-CTC-20060911-0041- v1.0 1About this Installation and Setup GuideAbout this Installation and Setup GuideSymbols UsedTerminologyGenerally, the Thomson ST585(v6)(i) will be referred to as Thomson Gateway in this Installation and Setup Guide.Typographical ConventionsFollowing typographical convention is used throughout this manual:>Sample text indicates a hyperlink.Example: For more information, visit us at www.thomson-broadband.com.>Sample text indicates an important content-related word.Example: To enter the network, you must authenticate yourself.>Sample text indicates a GUI element (commands on menus and buttons, dialog box elements, file names, paths and folders).Example: On the File menu, click Open to open a file.Documentation and software updatesThomson continuously develops new solutions, but is also committed to improving its existing products.For suggestions regarding this document, please contact documentation.speedtouch@thomson.net.For more information on Thomson's latest technological innovations, documents and software releases, visit us at http://www.thomson-broadband.com.iA note provides additional information about a topic.!A caution warns you about potential problems or specific precautions that need to be taken.
E-DOC-CTC-20060911-0041- v1.02About this Installation and Setup Guide
E-DOC-CTC-20060911-0041- v1.0Chapter 1Introducing the Thomson Gateway31 Introducing the Thomson GatewayIntroductionIn a minute you will be able to access the Internet using your Thomson Gateway.This Installation and Setup Guide will show you how to set up your Thomson Gateway and how to connect a computer or a Local Area Network (LAN) to the Internet.Identifying your Thomson GatewayThe label on the bottom of your Thomson Gateway informs you about the Thomson Gateway’s:>Product name>Model number>Serial number>Power requirementsDSL variantsThe Thomson Gateway comes in two ADSL variants:>POTS: The Thomson ST585(v6) connects to an analogue Plain Old Telephone Service (POTS) line.>ISDN: The Thomson ST585(v6)iconnects to an Integrated Service Digital Network (ISDN) line, enabling residences with an ISDN line to use the ADSL service.You can easily identify your variant by checking the product name printed on the label on the bottom of your Thomson Gateway.!Do not remove or cover the label.The ... variant supports ...POTS ADSLADSL2ADSL2+RE-ADSLISDN ADSLADSL2ADSL2+!Only use the Thomson Gateway variant which is appropriate for the DSL service provided to your premises.
E-DOC-CTC-20060911-0041- v1.0Chapter 1Introducing the Thomson Gateway4
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation52 Basic InstallationBefore you beginMake sure you read the safety instructions and regulatory notices first. You can find the safety instructions on the Setup CD (see “2.2 Installing your Thomson Gateway” on page 7). They may also be provided as a printed booklet.ADSL serviceThe ADSL service must be up and running on your telephone line.If both conventional telephone and ADSL service are simultaneously available from the same copper pair, you will need a central splitter or distributed filters for decoupling ADSL and telephone signals.Computer requirements>To connect computer(s) via Ethernet, make sure the computer(s) are equipped with an Ethernet network interface card (NIC).>For wireless networking, you will need a wireless 802.11 b/g compatible client adapter for each computer you intend to connect wirelessly.Wireless client adaptersYou can use one of the following wireless client adapters:>Thomson ST110g CardBus>Thomson ST121g USB adapter>Thomson ST122g USB adapter>Any other Wi-Fi certified WLAN clientInternet connection detailsYou need the following connection details from your Internet Service Provider (ISP): >Your ISP’s method for connecting to the Internet (for example PPPoE)>The VPI/VCI (for example 8/35)>Your user name and password to connect to the InternetYou must have received this information when you subscribed to DSL at your Internet Service Provider (ISP). You will be prompted for this information at a given step in the installation procedure.!Public telephone lines carry voltages that can cause electric shock. Only try to set up splitter/filters that have been designed to be installed by unqualified personnel. For further assistance, contact your Internet Service Provider.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation62.1 Mounting your Thomson GatewaySetup possibilitiesYou can mount the Thomson Gateway on a wall or simply place it on a desk.Wall mountProceed as follows to mount the Thomson Gateway on a wall or other vertical surface:1Drill two holes in the wall or other vertical surface where you want to place the Thomson Gateway.2Fasten two screws in the wall holes. The screws should protrude five millimetres from the surface of the wall.3Attach your Thomson Gateway on the wall using the two mounting slots on the bottom.iIf you install the Thomson Gateway onto plasterboard, use dowels to secure the screws. Otherwise the strain of the cables connected to the Thomson Gateway rear panel connectors could pull the Thomson Gateway from the wall.MODEM ACCESS CODE: 0123456789MAC: AAABCCCDDEEETHOMSON TELECOM*ACCESS CODE 0123456789**MACADDRESS AAABCCCDDEEE* SSID:SoeedTouchVVVVVVWEP (hex):1234ABCDEFWPA PSK: 1234ABCDEFTCM: 12345670SpeedTouch ZZZDSLBSFFFFF RQQIS/N:CPYYWWPPXXX (CC)*DSLBSFFFFF RQQI*DSLBSFFFFF RQQI*MACADDRESS AABCCCDDEEE*RATED INPUT: 18V~1000mA!
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation72.2 Installing your Thomson GatewayInternet connectivity setupThere are different ways to set up your Thomson Gateway. The best way depends on your operating system.If you use the following operating systemthe recommended way to set up your Thomson Gateway isMicrosoft Windows (98 SE, Millennium, 2000 or XP)the Home Install Wizard, as described in “2.2.1 Guided Installation” on page 8.Mac OS X, provided you use a wired connection to your Thomson GatewayAny operating system (provided you have IP connectivity)the Easy Setup, as described in “2.2.2 Manual Installation” on page 16.Mac OS X, wirelessly connected to your Thomson Gateway and provided you have IP connectivity
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation82.2.1 Guided InstallationIntroductionOn the CD, a Quick-Install Wizard is provided that will guide you through the first installation and setup of your Thomson Gateway.The Quick-Install Wizard will:>Provide important safety and regulatory information.>Show you how to make the necessary connections to your Thomson Gateway.>Show you how to turn on your device.>Prepare you to smoothly run the Thomson Gateway Home Install Wizard.The subsequent Home Install Wizard will then prepare your Thomson Gateway and your local computer(s) to connect to the Internet.The Home Install Wizard will:>Guide you through connecting your computer(s) to your Thomson Gateway.>Prepare the Thomson Gateway to connect to the Internet.Connecting the cables: wait!Do not plug in any cables until you are prompted to do so by the Quick-Install Wizard and/or the Home Install Wizard.Starting the CD for the first time To start the Thomson Gateway Setup:1Insert the Setup CD into your computer's CD-ROM or DVD-ROM drive. Microsoft Windows: The CD should autostart.Mac OS X: Double-click Menu in the window with the content of the CD.2Select the language of your choice and click OK.3The procedure continues with the Quick-Install Wizard.Proceed with “ Quick-Install Wizard” on page 8.Quick-Install WizardThe Quick-Install Wizard guides you through the first setup of your Thomson Gateway.1On the Welcome page, click Next to continue. !You need administrative rights to run the applications on the Setup CD on a Microsoft Windows 2000 or XP operating system, or Mac OS X computer.!If not, see ”The Thomson Gateway CD does not start automatically” on page 35.!If you ran the CD on this computer before, the Quick-Install Wizard is not shown; the CD menu appears instead (see “2.3 The Setup CD” on page 18 for more information).
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation92Select your Thomson Gateway from the list of supported devices and click Next.The Thomson Gateway Safety Instructions and Regulatory Notices are displayed. 3Scroll down and read all the instructions carefully, select I have read and I fully understand the Safety Instructions and Regulatory Information to confirm your reading, and then click Next.4Subsequent screens guide you through the preliminary hardware setup of your Thomson Gateway.Follow all the instructions carefully and click Next each time your are ready to proceed.5Click Set up my THOMSON ST to continue.6The procedure continues with the Home Install Wizard.Proceed with “ Home Install Wizard” on page 10.iA product picture helps you to easily identify your Thomson Gateway. If you are not sure what device you have, check the label on the bottom of your Thomson Gateway.!Your Thomson Gateway is designed and tested to meet the latest safety standards. However, to ensure safe use of this product, it is important that you carefully read and comply with the Safety Instructions and Regulatory Notices shown and/or available in the Safety and Regulatory booklet before you install the Thomson Gateway.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation10Home Install WizardThe Home Install Wizard guides you through your local network connections and prepares the Thomson Gateway to connect to the Internet. Proceed as follows:1On the Welcome page, click Next to continue.The Software License Agreement window appears.2You must accept before continuing. Click Yes to accept.The Home Install Wizard checks your system and invites you to connect the Thomson Gateway to your computer.!If you accepted the Software License Agreement in a previous configuration setup, this window will not be shown.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation113Make one of the following connections:Connect the yellow RJ-45 Ethernet cable to the yellow (indicated) Ethernet port on your Thomson Gateway and the other end to the computer’s Ethernet port.For wireless networking, plug a wireless card or adapter into your computer.4Once the hardware is installed and connected to the Thomson Gateway, the procedure continues with configuring your Internet connection.Proceed with “ Configuring the Internet connection” on page 12.iIn case of problems or for advanced information, see “2.5.1 Wireless Setup” on page 22.iIf the wizard does not detect a connection, an error message will be displayed. Refer to “The wizard does not detect a connection” on page 35.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation12Configuring the Internet connectionProceed as follows:1If prompted, enter the User name and Password for your Thomson Gateway security settings and click OK.2Select the appropriate Region, Provider and Service for your Internet connection as specified by your Internet Service Provider and click Next.3Your connection to the Internet connectivity is set up:Select the VPI/VCI - and, if required, the Connection Type - as specified by your Internet Service Provider and click Next.Enter the User Name and Password for your Internet account settings as specified by your Internet Service Provider and click Next.4The procedure continues with some additional configurations.Proceed with “ Configuring the Thomson Gateway (and your computer)” on page 13.iThe factory default user is ‘Administrator’ and its password is blank. It is advisable to specify another user name and password during the configuration procedure to protect your Thomson Gateway from security violation. See “2.6 Basic Security” on page 24 for more information.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation13Configuring the Thomson Gateway (and your computer)Proceed as follows:1Depending on the selected service profile and your ISP’s requirements, you may have to fill in some additional settings during the Home Install Wizard, like Dynamic DNS Service, Time Configuration or other.Enter the information provided by your ISP and click Next whenever requested.2To protect the wireless connections to your Thomson ST, move the slide control to the desired security mode.The following security modes to secure traffic between the Thomson Gateway and connected wireless stations are available:Low, which implies in fact that no security measures are taken at all.Medium, implying that traffic is encrypted by means of a static encryption key (WEP).High, providing the highest security standard available (WPA) for encrypting all wireless traffic.iFor an overview of all Thomson Gateway wireless security features, see “ Securing your wireless network” on page 24.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation143Provide a user name and password to protect your Thomson Gateway from unauthorised access. Each time a user wants to access a Thomson Gateway management interface, the user will be prompted to provide this user name and password before access is granted.Click Next to continue.4The procedure continues with the final steps of configuring your Thomson Gateway and your computer.Proceed with “ Finishing the Home Install Wizard” on page 15.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation15Finishing the Home Install WizardThe Home Install Wizard will configure the Thomson Gateway and your computer according to the service profile. Proceed as follows:1You can follow the configuration progress in following window:2Click Finish to close the wizard.The following steps will happen automatically:After some seconds, the Internet  LED on your Thomson Gateway will be lit green to indicate Internet connectivity. If not, refer to “4.2 LED Diagnostics” on page 31. If needed, you can test your Internet connection as described in “ Testing your Internet Connection” on page 33.The CD Menu is displayed. See “2.3 The Setup CD” on page 18 for more information.You are redirected to the embedded Thomson Gateway pages automatically (unless you cleared the http://dsldevice.lan check box in the last window of the Home Install Wizard). These pages allow you to configure the Thomson Gateway firewall, Thomson Gateway settings, your wireless access point settings, and so on. See the User’s Guide for more information.More on IP settings In most cases, the computer’s networking interface used during the Home Install Wizard procedure will be configured for obtaining its IP configuration dynamically. This is the most convenient configuration and should not be changed.iFor fixed or advanced IP configurations, please follow the instructions of your ISP.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation162.2.2 Manual InstallationWeb-based Easy SetupWith the help of the Easy Setup, your Internet connection is set up in a few clicks. The Easy Setup is Operating System independent.PreconditionsMake sure that:>Your Thomson Gateway is correctly set up and turned on.>Your computer is connected to the Thomson Gateway. In case of a wireless connection, a wireless client adapter has to be installed on your computer and correctly configured to connect to your Thomson Gateway.>Your host computer is configured as DHCP client or with a valid fixed IP address. For more information, refer to the Help of your browser.>Your Web browser is not using a proxy server. For more information, see “ Disable proxy server” on page 40.HTTP interceptProceed as follows:1Open a Web browser. Browse to an arbitrary Web site, for instance http://www.thomson-broadband.com. As long as no Internet connection has been set up, you will be automatically redirected to the Thomson Gateway Welcome page. 2Click Set up my SpeedTouch to start the Easy Setup wizard. 3Proceed with “ Using Easy Setup” on page 17.iSee “ Wiring” on page 20 for a comprehensive overview of all Thomson Gateway connections.iIn case of problems, you can give the host computer a fixed IP address in the same subnet as your Thomson Gateway (If the Thomson Gateway is in its default settings, that is an address between 192.168.1.1 and 192.168.1.253). In case you use fixed IP addresses, the Thomson Gateway has to be configured as DNS server.iIf you are not redirected automatically, go to “ Starting the Easy Setup wizard” on page 17.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation17Starting the Easy Setup wizardYou can also start the Easy Setup wizard from within the embedded Web pages. Proceed as follows:1Browse to the Thomson Gateway pages on http://dsldevice.lan or on its IP address, 192.168.1.254 by default).2In the menu, click SpeedTouch.3In the Pick a task list, click Set Up.Using Easy SetupIn the Easy Setup wizard:1Click Next to proceed. If for some reason you want to abort the wizard, click Cancel.2Choose the Service provided by your ISP (Router or Bridge) and click Next.3Select the appropriate VPI/VCI - and, if required, the Connection Type (PPPoE or PPPoA) - provided by your ISP, and then click Next.4For a Routed service, fill in the Internet Account settings (PPP user name and password) provided by your ISP, and then click Next.5Fill in a Security user name and Password for your Thomson Gateway.6In the next window you can review your settings, before starting the configuration of your Thomson Gateway. If something is missing or incorrect, click Back. To confirm your settings, click Start.7Wait until the configuration is finished, and then click Finish.iThe factory default user is ‘Administrator’ and its password is blank. It is advisable to specify another Administrator user name and password to protect your Thomson Gateway from security violation, as described in “2.6 Basic Security” on page 24.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation182.3 The Setup CDSetup CDYour Thomson Gateway comes with a Setup CD. If you insert the Setup CD into a Microsoft Windows PC or Mac OS X computer, an intuitive CD Menu guides you through the features and contents of the Setup CD and allows you to easily browse for user documentation, Thomson Gateway system software, service templates, etc.CD menuThe CD menu appears automatically each time you insert the CD, or after running the Quick-Install Wizard and subsequent Home Install Wizard:Select:>Run Quick Installation to start the Quick-Install Wizard and Home Install Wizard.>Maintenance to:Reconfigure your Thomson Gateway via the Home Install Wizard.Check for software upgrades.>Documentation and Help to:Consult user documentation for your Thomson Gateway.Consult user documentation for Thomson networking products.See more information on Thomson products and solutions.If you connect to the Internet, the document list will automatically be updated with the latest documentation.iIf you have problems viewing the documentation, see “ I cannot view the Thomson Gateway documentation” on page 36.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation19>Visit Thomson Broadband to visit the online support sections on www.thomson-broadband.com.>View CD Contents to open a new window to view the Setup CD contents.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation202.4 Thomson Gateway Connection EssentialsWiringThe image below shows all possible types of connection to the Thomson Gateway.Making connectionsIn most cases, the Quick-Install Wizard and Home Install Wizard will guide you through the process of making all the required connections to your Thomson Gateway.If you want to make the required connections yourself, see “2.5 Connections Overview and Powering” on page 21 for more information.Ethernet1432DSLReset1243ON/OFFiIt is recommended to wait to make any of these connections until the wizard prompts you to do so. See “2.2 Installing your Thomson Gateway” on page 7 for more information.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation212.5 Connections Overview and PoweringIntroductionIf you want to make the required connections yourself without using the guided installation procedure as recommended, you must:>Read the safety instructions and regulatory notices first.>Follow the order as indicated below.DSL connectionUse the grey DSL cable to connect the Thomson Gateway DSL port to your telephone wall outlet or distributed filter.Powering the Thomson GatewayPlug the coaxial jack of the electric power supply adapter into the Thomson Gateway power inlet port and the other end into the wall outlet.To turn on the Thomson Gateway, press the power button on the Thomson Gateway rear panel.During the start-up procedure, the power LED on the front panel is lit red for some seconds. As soon as the power LED is solidly lit green, your Thomson Gateway is ready for service. After another couple of seconds, also the DSL LED will light green.If these LEDs do not light, please refer to ”Checking the LEDs” on page 31. A comprehensive LED overview can be found in the User’s Guide.Use the same button to turn off your Thomson Gateway.Network connectionsYour Thomson Gateway allows you to connect your computer(s) via: >Ethernet>Wireless networkingiYou can find the safety instructions on the Setup CD (see “2.2 Installing your Thomson Gateway” on page 7). They may also be provided as a printed booklet.iThe Thomson Gateway electrical power requirements are indicated on the label on the bottom side of your Thomson Gateway. In case you need to use another power supply than the one provided, make sure that the spare supply complies with the Thomson Gateway power requirements.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation222.5.1 Wireless SetupWireless client adaptersIf you want a wireless connection to your Wi-Fi certified Thomson Gateway, you need a wireless 802.11 b/g compatible client adapter.You can use one of the following wireless client adapters:>Thomson ST110g CardBus>Thomson ST121g USB adapter>Thomson ST122g USB adapter>Any other Wi-Fi certified WLAN client>A built-in Wi-Fi certified WLAN adapter, if present in you computeriTo install hardware on a Microsoft Windows 2000 or a Microsoft Windows XP operating system, you need administrative rights on your computer.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation23Installing your wireless client adapterProceed as follows when the Home Install Wizard prompts you to plug in the wireless client adapter:1Plug in the wireless client adapter. The hardware is being installed.2Enter your Thomson Gateway’s serial number and click Next.A progress window appears, showing the setup of the wireless connection to your Thomson Gateway.3Continue with ”Configuring the Internet connection” on page 12.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation242.6 Basic SecurityDefault user name and passwordThe Thomson Gateway comes with a default user. Its user name is ‘Administrator’ and the default password is blank.Changing your passwordFor security reasons, it is recommended to set a password to access the Thomson Gateway. Proceed as follows:1Go to the Thomson Gateway home page (http://dsldevice.lan or 192.168.1.254).2In the left pane, choose Toolbox > User Management. 3In the Pick a task list, click Change my password.4Enter a new password and confirm.  Default wireless security settingsAlso for wireless connections to your Thomson Gateway, by default there are no security settings, so the Thomson Gateway is initially accessible to all wireless devices:>The Network Name (SSID) is broadcast.>The security level is initially set to Low (that is: no encryption is used).>The Access Control List (ACL) is open and empty. New stations are automatically allowed to access the Thomson Gateway.It is recommended to change these Thomson Gateway wireless access point settings either automatically via the Thomson Gateway Home Install Wizard, either manually as described in the Thomson Gateway User’s Guide.Securing your wireless networkTo secure your wireless network, you can:>Allow or deny access based on the MAC address of the wireless client(s). Known MAC addresses are kept in the Access Control List (ACL). If the Thomson Gateway is configured to allow new stations via registration, unknown computers will have to register before they can connect.>Turn off the broadcast of the wireless Network Name (SSID). New wireless clients that are scanning for available networks will not see your network appear in their list.iDo not forget this logon information or you will be forced to reset the Thomson Gateway back to its default configuration.iFor the ACL you have the following options: >Allowed (automatically): All new stations can access the Thomson Gateway.>Allowed (via registration): Only allowed stations in the ACL have access. You can add new stations via the Association / Registration button.>Not allowed: Only allowed stations in the ACL have access.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation25>Encrypt the data that will be sent over the wireless network. You can choose different encryption methods or levels of security:High: Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) encryption, the highest form of security available. This can only be used if your wireless client and client manager support it.Medium: Wired-Equivalent Privacy (WEP) encryption.Low: no encryption, no security.iFor more information, see the Thomson Gateway User’s Guide.
E-DOC-CTC-20060911-0041- v1.0Chapter 2Basic Installation26
E-DOC-CTC-20060911-0041- v1.0Chapter 3Web-Based User Interface273 Web-Based User InterfaceEmbedded pagesThe Thomson Gateway comes with embedded web pages, providing an interface to the software installed on the device. It allows Easy Setup and management of the Thomson Gateway via your web browser from any computer connected to the Thomson Gateway.AccessProceed as follows to access the pages:1Open your Web browser.2In the address bar, type http://dsldevice.lan or your Thomson Gateway’s IP address (the default IP address is 192.168.1.254) and press ENTER. 3Enter your Thomson Gateway security user name and password. 4The Thomson Gateway’s home page will be displayed in your browser. From here - depending on the rights of your user account - you have access to the other pages.TasksAmong others, you can:>View the Thomson Gateway’s current settings and status.>Configure the Thomson Gateway to connect to your Service Provider with the settings provided.>Set the Thomson Gateway’s firewall to work with specific applications.>Set up security features.>Enable remote management access.>Back up your configuration settings.>Reset the Thomson Gateway’s default settings.Using the Web pagesWhen making changes to the Thomson Gateway configuration via the Web pages, the configuration is stored automatically whenever you click Apply. For more information on the embedded pages, refer to the Help in the upper right corner of the notification and navigation area or refer to the Thomson Gateway User’s Guide.iThe default user name is ‘Administrator’ and the default password is blank.
E-DOC-CTC-20060911-0041- v1.0Chapter 3Web-Based User Interface28Site MapThe following Site Map gives you an overview of the main pages:ToolboxFirewallHome NetworkSpeedTouchBroadband ConnectionInformationConfigurationEvent LogsDSL ConnectionInternet ServicesRemote AssistanceParental ControlIntrusion DetectionDynamic DNSUser ManagementGame & Application SharingDevicesInterfaces
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting294 TroubleshootingWhat to checkThe first things to check if you cannot access the Internet, are:>Power>Hardware connections>LEDsConfiguration problemsIf your Thomson Gateway is unreachable due to misconfiguration, you might consider a hardware reset to factory defaults as described in “4.7 Reset to Factory Defaults” on page 41.If the suggestions in this chapter do not resolve the Internet connection problem, please contact your Internet Service Provider.!However, note that resetting the Thomson Gateway to its factory settings will revoke all the changes you made to the configuration.
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting304.1 Checking the HardwareCheck the wiringPlug in properly all the cables you need. Make sure that the cables between your Thomson Gateway, computers and telephone socket are plugged in firmly. Loose connections can affect your Internet connection.Damaged cables can interfere with your Internet connection. Check for damage along the cables and loose connections at the end of the cable. Replace any damaged cables.Test the telephone lineTo eliminate the possibility of a fault with the telephone line itself, check for a dialling tone by using a telephone connected to the telephone master socket. If you are using ADSL, check whether a splitter has been installed or that micro-filters have been correctly fitted. Contact your telephone company if there is no dialling tone.Restart your computerLoss of Internet or network connectivity may be caused by the computer. Restarting your computer may solve the problem.Power-cycle the Thomson GatewayTo restart your Thomson Gateway, simply turn it off. Wait five seconds and turn it back on.
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting314.2 LED DiagnosticsChecking the LEDsAfter establishing a connection with the Internet, at least the following LEDs should solidly light green: Power, DSL, Internet.LED status Possible solutionsNo LEDs are lit The Thomson Gateway is not turned on, or turned off.>Make sure the Thomson Gateway is plugged into an electrical outlet.>Make sure you are using the correct power supply for your Thomson Gateway. The Thomson Gateway electrical power requirements are indicated on the label on the bottom of your Thomson Gateway.>Make sure the Thomson Gateway is turned on.>Unplug the Thomson Gateway, restart your computer and then plug the Thomson Gateway back in.Power LED is lit red or flashing amberThe Thomson Gateway is malfunctioning or not able to start up.>Fully unplug the Thomson Gateway from your computer and disconnect it from its power supply. Wait five seconds, connect the Thomson Gateway again and turn it back on.DSL LED is flashing green or no DSL LEDYour DSL service is unable to synchronise.>Make sure the Thomson Gateway is plugged into the DSL-enabled phone line.>Make sure micro-filters are correctly fitted (if not, it is very likely that your regular telephone service is not working properly).>Make sure you have the correct Thomson Gateway variant (ISDN or POTS) according the DSL/phone service provided to your premises.>If you have previously had a working connection, call your ISP to check for service outages.No Ethernet LEDNo Ethernet port’s Link Integrity/Activity LEDNo Ethernet connectivity: >Make sure the Ethernet cable(s) are firmly connected to the 10/100Base-T port.>Make sure you are using the correct cable type for your Ethernet equipment.>Make sure the Ethernet NIC driver is correctly installed and enabled on your computer. Power safe options for the Ethernet NIC should preferably be disabled.
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting32You can find a comprehensive LED overview in the User’s Guide.WLAN LED is flashing or not lit>The WLAN LED flashes if there is wireless LAN activity and can have different colours:Green: The Thomson Gateway wireless access point is operating in the highest security mode (WPA). Make sure to use the same WPA encryption on the WLAN client.Amber: The Thomson Gateway wireless access point is operating in medium security mode (WEP). Make sure to use the same WEP encryption on the WLAN client.Red: The Thomson Gateway wireless access point uses no security.>The WLAN LED is not lit if the Thomson Gateway wireless access point is disabled. For wireless networking, make sure the WLAN is enabled on the Thomson Gateway. Proceed as follows:1Go to the Thomson Gateway Web pages.2In the menu select Home  Network > Interfaces.3Click WLAN.4Click Configure.5Select Interface Enabled.- OR - 1Press and hold the Association / Registration button until the WLAN LED is lit (green, amber or red).2The WLAN LED is toggling between red and green: If new stations are only allowed via registration and if you pressed the Association / Registration button, the ACL will be unlocked for 30 seconds during which you can connect new wireless clients.Red Internet LED or No Internet LED>There was an authentication failure. This will usually present itself as an error message regarding an incorrect password.Check whether your user name is correct. For ADSL connections, the user name is normally in the form of username@ISP.Check whether your password is correctly entered. The password is case sensitive.If you continue to get password failures, contact your ISP.>The wrong service profile was selected. Restart the setup of your Thomson Gateway, and make sure to select the correct service profile.LED status Possible solutions
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting334.3 Web DiagnosticsTesting your Internet ConnectionAfter setting up the Internet connection, there is an easy way to check whether your configuration is fine. Proceed as follows:1Go to the Thomson Gateway home page (http://dsldevice.lan or 192.168.1.254). 2In the menu, click SpeedTouch. 3In the Pick a task list, click Check connectivity to the Internet.4In the Internet Service to Check box, select the Internet service you want to check.5Click Check Connectivity.If the test is successful, you will see a list of green check marks as shown in the example below:Otherwise a red cross will help you to diagnose the problem:Test result ExplanationYour DSL line is not synchronised.>Check whether your telephone line is correctly connected to your Thomson Gateway.>Check the DSL LED, as described in “ Checking the LEDs” on page 31.No ATM activity detected on your DSL line.
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting34No Ethernet activity.If you are connected through a protocol other than PPPoE, this check is not applicable as the result will always be ‘No Ethernet activity’. >Authentication failed: check your user name and password. The user name is in most cases in the form of username@ISP.>Your connection is disconnected.>Could not bring up link.No IP No IP address or no DNS server has been configured. During IP address negotiation, there was an IPCP error or a DHCP error. No Internet This test sends 1 ping to each address of a configured list of IP addresses. The test succeeds if all addresses can be reached. If your primary and secondary DNS server are part of the list, reaching one of both is enough.No DNS The DNS service provided by your ISP may have a problem. Test result Explanation
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting354.4 Thomson Gateway Setup CD TroubleshootingThe Thomson Gateway CD does not start automaticallyProceed as follows:>In Microsoft Windows:1In the Windows task bar, click the Start button. 2Select Run.3In the Open field, enter the following path: D:\Setup.exe, where D stands for the drive letter of your CD-ROM drive.>In Mac OS X: 1On your desktop, double-click the CD icon.2Double-click Menu.The wizard does not detect a connectionIf the Home Install Wizard does not detect a connection to your Thomson Gateway, an error window appears. If this is the case, check whether:>The Thomson Gateway is turned on and fully initialised.>Your computer has a valid IP address, that is any address but 0.0.0.0. In Microsoft Windows:1In the taskbar, click the Start button.2Select Run.3In the Open field, type cmd.4Click OK.A black window will appear with a flashing cursor.
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting365Type ipconfig /all and press ENTER.Your IP address is displayed. In Mac OS X:1Go to Dock > System Preferences.2Click Network.3Click the TCP/IP tab.Your IP address is displayed.>No dedicated firewall device or router is placed between your computer and the Thomson Gateway.>No personal network security software (for example firewall software) is running on your computer.>Your computer is correctly connected to the Thomson Gateway, or the WLAN client is correctly associated with the Thomson Gateway.1In the Windows XP notification area, click the Wireless Network Connection icon   or the Thomson Gateway Client Manager icon  .2Check whether the displayed network has your Thomson Gateway network name (SSID).To repeat the search for your Thomson Gateway, click Back or restart the wizard. As soon as the wizard finds your Thomson Gateway, you can continue with “ Configuring the Thomson Gateway (and your computer)” on page 13.The Thomson Gateway is not respondingIf the completion window does not appear after running the Thomson Gateway Home Install Wizard, this means that the Thomson Gateway is not responding or not accessible anymore.There are two possibilities:>This might be due to the reconfiguration of the Thomson Gateway’s IP settings or wireless access point settings. In this case, the last window of the Home Install Wizard will not be shown. Your Thomson Gateway is correctly set up though and you will be able to surf the Internet.>If you did not reconfigure the Thomson Gateway’s IP settings or wireless access point settings, restart the Home Install Wizard.If the problem persists, refer to the Service Provider’s instructions for more information.I cannot view the Thomson Gateway documentation To be able to view the Thomson Gateway documentation pages on the Setup CD, JavaScript must be enabled in your Web browser. For more information, refer to the Help of your Web browser.To allow active content on a Microsoft Windows XP system, see “ I get a warning about active content in Internet Explorer” on page 37.iIn Microsoft Windows 98 or Microsoft Windows Millennium, type winipcfg and then press ENTER.iIf you are not connected, this icon will have a red cross: iIf the setup fails over a wireless connection, try to set up your Thomson Gateway using a wired connection.
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting37I get a warning about active content in Internet Explorer When opening documentation pages from the Setup CD, a warning might be displayed. This may be the case when the pages are opened in Internet Explorer and you are using Microsoft Windows XP with Service Pack 2.Proceed as follows to view the documentation:1In Internet Explorer, the following message will appear in the Information Bar:2Click the Information Bar (with the warning).3Select Allow Blocked Content.A security warning is displayed:4Click Yes.You can now view or print the Thomson Gateway documentation pages.iThis warning will be displayed every time you consult the documentation. If you do not want this message to be shown in the future, you must allow CDs to run active content on your computer:1In the Internet Explorer menu, select Tools > Internet Options.2Click the Advanced tab.3Under Security, select Allow active content from CDs to run on My Computer.
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting384.5 Windows Zero ConfigurationAbout Windows Zero Configuration (WZC)The Windows Zero Configuration (WZC) service allows you to automatically configure your wireless connections. WZC is a part of Windows XP SP 2 and above. When you install a Thomson Gateway wireless networking product, it will automatically use WZC whenever possible. If not, a dedicated client utility is installed. How to Open the WZC ServiceBy default, WZC should be active. To open the service click Start > Connect to > Wireless Network Connection.This opens the Wireless Network Connection window : The installation of your wireless network adapter may have disabled WZC. In this case,the following will appear: You should use the utility corresponding with your wireless network adapter to connect to your wireless network, or restore WZC. Refer to the documentation of your wireless product and the microsoft knowledge database on www.microsoft.com for more information.
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting39How to Establish a Wireless Connection using the WZCProceed as follows to start and use the WZC service: 1Open the Wireless Network Connection window (see above)2From the list, double-click the network you wish to connect to, or select it and click Connect.Result: The WZC may prompt you for an SSID and a WPA or WEP Key (in case of a secure network):  3If applicable, fill in the SSID and the key and click Connect.Result: a wireless connection to your Thomson Gateway will be established. When the connection is ready, Windows informs you through a popup balloon in the notification area: iThe typical SSID is SpeedtouchXXXXXX where XXXXXXrepresents a set of alphanumerical characters. You can find the SSID and the key on the label on the bottom of the Thomson Gateway.iFor more detailed information about starting and using the WZC service, visit the Microsoft knowledge base on http://support.microsoft.com.
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting404.6 Easy Setup TroubleshootingPrerequisitesBefore you run the Easy Setup on the embedded Thomson Gateway pages, make sure that:>The necessary connections are made.>The Thomson Gateway is turned on.>Your host computer is configured as DHCP client or with a valid fixed IP address.Supported Web browsersYour Web browser must be able to run JavaScript.Disable proxy serverThe Easy Setup only works if the proxy server is disabled or bypassed for local addresses. For more information, refer to the Help of your Web browser.Proceed as follows to disable a proxy server in Internet Explorer:1In the Internet Explorer menu, choose Tools > Internet Options.2Click the Connections tab.3Click the LAN settings... button. 4Clear the Use proxy server box and the Use automatic script box. iIf you have any problems, you can give the host computer a fixed IP address in the same subnet as your Thomson Gateway (If the Thomson Gateway is in its default settings, that is an address between 192.168.1.1 and 192.168.1.253).If you use fixed IP addresses, the Thomson Gateway has to be configured as DNS server (default).!It is recommended to disable all other network connections on your computer first, except the one connecting to your Thomson Gateway.Proceed as follows to disable a network connection:1In the Windows XP taskbar, click the Start button.2Choose (All) Programs > Control Panel > (Network and Internet Connections >) Network Connections.3Right-click the network interface icon you want to disable and choose Disable.
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting414.7 Reset to Factory DefaultsResetting your Thomson GatewayYou might consider a reset to factory defaults as described below.A reset to factory default settings deletes the configuration profile settings. Therefore, after the reset, a reconfiguration of your Thomson Gateway will be needed.Reset to default configurationProceed as follows:1Make sure the Thomson Gateway is turned on.2Use a pen or an unfolded paperclip to push the recessed reset button on the back panel. The reset button is marked with a red circle. Push it until the power LED lights red - this will take about 7 seconds.3Release the reset button.4The Thomson Gateway restarts.!Be aware that a reset to factory defaults will revoke all configurational changes you made to the Thomson Gateway.Ethernet1432DSLReset1243ON/OFF
E-DOC-CTC-20060911-0041- v1.0Chapter 4Troubleshooting42
THOMSON Telecom BelgiumPrins Boudewijnlaan 472650 Edegemwww.thomson-broadband.com© Thomson 2007. All rights reserved.E-DOC-CTC-20060911-0041- v1.0.

Navigation menu