Technicolor Delivery Technologies Belgium 589VACV2HP Technicolor xDSL Gateway User Manual TG589vac v2 QIG indd

Technicolor Delivery Technologies Belgium Technicolor xDSL Gateway TG589vac v2 QIG indd

Contents

User Manual

11.  Before you startCarefully read the Safety Instructions and Regulatory Notices booklet included in the box before continuing with the installation of the MediaAccess Gateway.2.  Check the content of your boxYour box contains the following items: BAFLINEDSL PHONEGEDHCItem DescriptionA   This Quick Installation Guide.B   One Safety Instructions and Regulatory Information booklet.C   One MediaAccess TG589vac v2.In this document we will refer to it as MediaAccess Gateway.D   One power adapter.E   One DSL cable with grey connectors.F   One DSL splitter/fi lter (optional).G   One Ethernet cable with yellow connectors.H   One Ethernet cable with red connectors (optional)23.   Connect the MediaAccess Gateway to the Broadband serviceChoose your setupTo connect the MediaAccess Gateway to the Internet you can either: Directly connect the MediaAccess Gateway to your service provider’s DSL network. In this setup the MediaAccess Gateway is used as DSL gateway. Follow the instructions from “Option A: DSL Gateway setup” on page2. Place the MediaAccess Gateway behind another Internet access device (for example, an optical network terminal for fi bre). In this setup the MediaAccess Gateway is used as local router. Follow the instructions from “Option B: Local router setup” on page3. Option A: DSL Gateway setupDSL1  Plug the DSL cable into the grey port labelled DSL of the MediaAccess Gateway.2  If your delivery: Does not include a DSL splitter, plug the other end of the DSL cable into your telephone wall socket. Includes a DSL splitter, plug the other end of the DSL cable into the DSL/Modem port of the DSL splitter. Plug the (LINE) cable of the DSL splitter into your telephone wall socket.3 Option B: Local router setupWAN1  Plug the Ethernet cable with the red connectors into the red port labelled WAN.2  Plug the other end of the Ethernet cable into your Internet access device’s Ethernet port.4.  Power on the MediaAccess Gateway1  Plug the connector of the electric power supply adapter into the MediaAccess Gateway power inlet port ( ). Plug the adapter into a nearby power outlet.2  Press the power button ( ) on the back panel.If the   LED is blinking green or orange, the MediaAccess Gateway is updating its software. If this is the case, wait until the   LED becomes solid on. This can take several minutes! Do not power o  your device or unplug any cables!4ChecChecboth ConYou c A1 2 3 4 5 5.  Connect your wired (Ethernet) devicesIf you want to connect a device using a wired (Ethernet) connection:1  Take the Ethernet cable with the yellow connectors.2  Connect one end of the Ethernet cable to one of the yellow Ethernet ports on your MediaAccess Gateway.3  Connect the other end of the Ethernet cable to your device.4  Connect your other Ethernet devices.5  We recommend you to fi rst confi gure the MediaAccess Gateway (see “7. Confi gure your MediaAccess Gateway from your browser” on page6) before connecting your wireless clients (see “6. Connect your wireless devices” on page4).6.   Connect your wireless devicesAfter you have connected the fi rst device, confi gure the MediaAccess Gateway fi rst (see “7. Confi gure your MediaAccess Gateway from your browser” on page6) before connecting the other wireless clients.MediaAccess Gateway access pointsThe MediaAccess Gateway has two wireless access points: The 5 GHz access point o ers superior transfer rates, is less sensitive to interference and allows you to connect IEEE802.11a/n/ac wireless clients. The 2.4 GHz access point allows you to connect IEEE802.11b/g/n wireless clients. Use this access point for wireless clients that don’t support 5 GHz.
5Check the status of the wireless access pointsCheck the status of the   and   LEDs on the MediaAccess Gateway’s top panel. If both LEDs are o  then briefl y press the   button to re-enable the wireless access points.If all LEDs are o  except the   LED, then briefl y press the   button to temporarily activate the status LEDs.Connection procedureYou can connect to an access point: Automatically using WPS:1  Start WPS Push Button Confi guration (PBC) on your wireless device.2  If your wireless device prompts you to select your access point from a list, select the item that uses the Network Name printed on the bottom label of your MediaAccess Gateway.3  Briefl y press the WPS ( ) button on the side panel of the MediaAccess Gateway.Network NameWPS4  The WPS ( ) LED on the top panel starts blinking orange.5  After maximum two minutes, the WPS  LED will be in either of the following states: Solid green: the registration was successful.  Blinking red: the MediaAccess Gateway could not fi nd your wireless device. Try again or connect your wireless devices manually.r ure way ce Use 6 Manually:Confi gure your wireless device with the Network Name and Wireless Key printed on the bottom label of your MediaAccess Gateway.Network NameWireless Key7.  Confi gure your MediaAccess Gateway from your browserStep 1: Browse to the MediaAccess Gateway user interface1  Browse to http://192.168.1.1 on a computer or device that is currently connected to your MediaAccess Gateway (either wired or wirelessly).2  The MediaAccess Gateway user interface appears. By default, you are logged in as guest. This means that some items are hidden. To view all items, click Sign In and enter admin as user name and the ACCESS KEY printed on the bottom of the MediaAccess Gateway as password.ACCESS KEYStep 2: Check your Internet connectionUnder Internet Access, check the status of your Internet connection. If it is not connected, click Internet Access, enter the Username and Password for your Internet connection and then click Save.7Step 3: Confi gure your wireless access points1  Click Wireless. The Wireless page appears. The 2.4 GHz access point is selected in menu on the left.2  Change the following settings under Access Point:1  In the SSID name box, type the network name that you want to use for this access point (if you do not want to use the default one).2  In the Security Mode list under Access Point, select the security mode that you want to use for this access point. We recommend to use WPA+WPA2-PSK. Do not use WEP or None, since they are not secure. WPS will be disabled if you select WEP.3  In the Wireless Password box, type the wireless key that you want to use for this access point. The key must consist of 8 to 63 alphanumeric characters. For example:MyKey123.3  Click Save.4  In the menu on the left, click the 5 GHz access point, confi gure the Access Point settings (as in step 2) and click Save.5  Reconnect your wireless client(s) to the MediaAccess Gateway using these new security settings.QUICK INSTALLATION GUIDEMediaAccess TG589vac v2Copyright 2015 Technicolor. All rights reserved. All referenced are service marks, trademarks, or registered trademarks of their respective companies. Specifi cations subject to change without notice.  DMS3-QIG-25-190 v1.0.*DSL37325630*DSL37325630

Navigation menu