TVS Electronics MSP250 Printer User Manual OUTER

TVS Electronics Limited Printer OUTER

users manual

FORWARD MICROFEED REVERSE MICROFEEDPAPER PARKMENUMODECOPYMODESingle SheetInsertion66Selecting and Loading paper Paper Select Lever for Continuous feedInstalling the Printer Ribbon11Installing your PrinterPower Switch Location Connection Parallel Interface CableComponents in your printer223344Paper Insertion Bottom Feed(Pull Tractor Option)88Printing Continuous Paperwith Tractor Unit in Pull Position77Tractor Select Lever55Printing in Single Sheets991010 Control PanelMSP 9 wire printer Operating the control panelONLINE light glows, the printer is in Normal Operation Mode.OFFLINE will pause printing.LF moves one line forward.FF moves one page forward.FONT to select a style of the character.PITCH to select the size of the characterMSP 24 wire printer Operating the control panelONLINE light glows, the printer is in Normal Operation Mode.OFFLINE will pause printing.LF moves one line forward.FF moves one page forward.FONT to select a style of the character.PITCH to select the size of the characterMail back your warranty registration card todaySelect LeverPrinting Continuous Stationeryin Push Tractor ModeSelect LeverInsertionPlatenParallelInterfaceInserting Continuous Paper in Push TractorHelpful Hints• Use Normal Density MSP Ribbons for 9 wire Printers. Use of improper ribbon may  damage the print head and invalidate the warranty.• Use only High Density MSP Ribbons for 24 wire Printers. Use of improper ribbon may  damage the print head and invalidate the warranty.• If you are replacing a ribbon be sure the printer of OFF and the print head has cooled.• Carefully read the instructions for correct ribbon placements. Improper placement can  cause smudged printing and may jam the ribbon.• ONLINE is the printer's normal operating mode. When the printer is ONLINE, it can  receive data from your computer and print. When the printer is OFFLINE, it stops  printing and responds only to control-panel instructions, such as moving the paper.• To completely cancel the print job, first cancel the job in your software application. Then clear the data from the printer buffer.• Because of advanced paper-handling features it is seldom necessary to turn the paper  feed knob. More frequently turning the paper feed knob causes misalingment. Use the Control panel instead.• Paper tear off, top-of-form adjustment and paper parking are not available when using  tractor in PULL mode.• Do not rotate the PLATEN KNOB when the printer is in power ON condion.• The top margin is usually set by your software. You may not need to change the top-of- form setting very often.• For serial interface connection you need to install an optional serial interface board.  Please contact your nearest TVS-E dealer. Serial interface cable comes with a board.• If the printer is used heavily or in a dusty environment consult TVS-E service centre for  advice on periodic cleaning and lubrication. www.tvs-e.comQuick Reference Guide
Federal Communications Commission (FCC) Requirements, Part 15 This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ---Reorient or relocate the receiving antenna. ---Increase the separation between the equipment and receiver. ---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ---Consult the dealer or an experienced radio/TV technician for help. NOTE THIS MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

Navigation menu