THALES DIS AlS Deutschland ELS31-V LTE Module User Manual hid

Gemalto M2M GmbH LTE Module hid

UserManual.wiki >

THALES DIS AlS Deutschland >

ELS31 V User Manual

User Manual

 M2M.GEMALTO.COMCinterion® ELS31-V/ELS51-VHardware Interface OverviewVersion: 00.502DocId: ELS31-V_ELS51-V_HIO_v00.502

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview Contents35ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 1 of 35Contents1 Introduction ................................................................................................................. 21.1 Key Features at a Glance .................................................................................. 21.2 ELS31-V / ELS51-V System Overview .............................................................. 52 Interface Characteristics ............................................................................................ 62.1 Application Interface .......................................................................................... 62.1.1 USB Interface........................................................................................ 62.1.2 Serial Interface ASC0 ........................................................................... 72.1.3 Serial Interface ASC1 (ELS51-V Only) ................................................. 82.1.4 UICC/SIM/USIM Interface..................................................................... 92.1.5 GPIO Interface.................................................................................... 112.1.6 I2C Interface ........................................................................................ 122.1.7 SPI Interface ....................................................................................... 132.1.8 Pulse Counter ..................................................................................... 132.1.9 HSIC Interface (ELS51-V Only) .......................................................... 132.1.10 SDIO Interface (ELS51-V Only).......................................................... 132.1.11 Control Signals.................................................................................... 132.1.11.1 Status LED .......................................................................... 132.1.11.2 Fast Shutdown .................................................................... 132.2 RF Antenna Interface....................................................................................... 142.2.1 Antenna Installation ............................................................................ 152.3 Sample Application .......................................................................................... 163 Operating Characteristics ........................................................................................ 183.1 Operating Modes ............................................................................................. 183.2 Power Supply................................................................................................... 194 Mechanical Dimensions, Mounting and Packaging............................................... 204.1 Mechanical Dimensions of ELS31-V / ELS51-V .............................................. 205 Regulatory and Type Approval Information ........................................................... 225.1 Directives and Standards................................................................................. 225.2 SAR requirements specific to portable mobiles ............................................... 245.3 Reference Equipment for Type Approval......................................................... 255.4 Compliance with FCC and IC Rules and Regulations ..................................... 266 Document Information.............................................................................................. 286.1 Revision History............................................................................................... 286.2 Related Documents ......................................................................................... 286.3 Terms and Abbreviations................................................................................. 286.4 Safety Precaution Notes .................................................................................. 327 Appendix.................................................................................................................... 337.1 List of Parts and Accessories........................................................................... 33

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview Tables35ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 1 of 35TablesTable 1: Signals of the SIM interface (SMT application interface) ................................. 9Table 2: GPIO lines and possible alternative assignment............................................ 11Table 3: Return loss in the active band........................................................................ 14Table 4: Overview of operating modes ........................................................................ 18Table 5: Directives ....................................................................................................... 22Table 6: Standards of North American type approval .................................................. 22Table 7: Standards of Verizon type approval............................................................... 22Table 8: Standards of GCF type approval.................................................................... 22Table 9: Requirements of quality ................................................................................. 22Table 10: Standards of the Ministry of Information Industry of the People’s Republic of China............................................................................ 23Table 11: Toxic or hazardous substances or elements with defined concentration limits............................................................................................................... 23Table 12: Antenna gain limits for FCC and IC................................................................ 26Table 13: List of parts and accessories.......................................................................... 33Table 14: Molex sales contacts (subject to change) ...................................................... 34

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview Figures35ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 1 of 35FiguresFigure 1: ELS31-V / ELS51-V system overview.............................................................. 5Figure 2: USB circuit ....................................................................................................... 6Figure 3: Serial interface ASC0....................................................................................... 7Figure 4: Serial interface ASC1....................................................................................... 8Figure 5: External UICC/SIM/USIM card holder circuit ................................................. 10Figure 6: Schematic diagram of ELS31-V / ELS51-V sample application..................... 17Figure 7: ELS31-V– top and bottom view...................................................................... 20Figure 8: Dimensions of ELS31-V / ELS51-V (all dimensions in mm)........................... 21Figure 9: Dimensions of ELS31-V / ELS51-V (all dimensions in mm) - bottom view .... 21Figure 10: Reference equipment for Type Approval ....................................................... 25

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview1 Introduction5ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 2 of 351 IntroductionThis document1 describes the hardware of the Cinterion® ELS31-V and ELS51-V modules for Verizon Network. It helps you quickly retrieve interface specifications, electrical and mechani-cal details and information on the requirements to be considered for integrating further compo-nents.The ELS31-V and ELS51-V modules include a baseband, a complete dual band RF frontend, memory and required circuitry to meet 3GPP E-UTRA (Long Term Evolution - LTE, Release 10 set of specifications) and Verizon Wireless LTE UE specifications.The module variants differentiate a follows:- ELS31-V provides LTE connectivity with IP Services- ELS51-V adds a Linux execution environment available for customer applicationsNote: Throughout the document ELS31-V refers to ELS31-V Release 2.1.1 Key Features at a Glance1. The document is effective only if listed in the appropriate Release Notes as part of the technicaldocumentation delivered with your Gemalto M2M product.Feature ImplementationGeneralFrequency bands LTE dualband: B4, B13Output power Class 3 (+23dBm +-2dB) for LTE AWS, LTE B4Class 3 (+23dBm +-2dB) for LTE 700, LTE FDD B13Power supply 3.3V to 4.5VOperating temperature (board temperature) Normal operation: -30°C to +80°CExtended operation: -40°C to +90°CPhysical Dimensions: 27.6mm x 18.8mm x 2.2mmWeight: approx. 3gRoHS All hardware components fully compliant with EU RoHS DirectiveLTE features3GPP Release 9 DL 10Mbps, UL 5MbpsLTE Cat. 1 data ratesSMS Point-to-point MT and MOText and PDU modeStorage in mobile equipmentSoftwareAT commands Hayes, 3GPP TS 27.007, TS 27.005, product specificSIM Application Toolkit SAT Release 99Firmware update Generic update from host application over ASC0 or USB modemOTA over ASC0 and over USB

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview1.1 Key Features at a Glance5ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 3 of 35InterfacesModule interface Surface mount device with solderable connection pads (SMT application interface). Land grid array (LGA) technology ensures high solder joint reli-ability and allows the use of an optional module mounting socket.For more information on how to integrate SMT modules see also [4]. This application note comprises chapters on module mounting and application layout issues as well as on SMT application development equipment.USB USB 2.0 High Speed (480Mbit/s) device interface, Full Speed (12Mbit/s)compliant2 serial interfaces ASC0:• 8-wire modem interface with status and control lines, unbalanced, asyn-chronous• Default baud rate: 115,200 baud• Adjustable baud rates: 1,200 to 921,600, no autobauding support• Supports RTS0/CTS0 hardware flow control. • indication of incoming data/SMS on RING0 (can be used to wake uphost from power down modes)ELS51-V only:ASC1 (shared with GPIO lines):• 4-wire, unbalanced asynchronous interface• Default baud rate: 115,200 baud• Adjustable baud rates: 1,200bps to 921,600bps• Supports RTS1/CTS1 hardware flow controlUICC interface Supported SIM/USIM cards: 3V, 1.8VEmbedded UICC Module is prepared for an embedded UICCGPIO interface 20 pads of the application interface programmable as GPIO pads (17) or GPO pads (3):GP(I)Os can be configured as COUNTER, FST_SHDN, ASC0, ASC1, and SPI signal linesProgramming is done via AT commandsI2C interface Supports I2C serial interfaceSPI interface Supports SPI interfaceSDIO ELS51-V only:4 wire interface.HSIC ELS51-V only:High Speed Interchip Communication interface. ADC Analog-to-Digital Converter with one unbalanced analog input.Digitial audio interface Hardware prepared for future use.Antenna interface pads 50 LTE main antenna, 50LTE diversity antennaFeature Implementation

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview1.1 Key Features at a Glance5ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 4 of 35Power on/off, ResetPower on/off Switch-on by hardware signal ON Switch-off by AT command Switch off by hardware signal GPIO4/FST_SHDN instead of AT commandAutomatic switch-off in case of critical temperature and voltage conditions Reset Orderly shutdown and reset by AT commandEmergency reset by hardware signal EMERG_RSTEvaluation kitEvaluation module ELS31-V / ELS51-V module soldered onto a dedicated PCB that can be connected to an adapter in order to be mounted onto the DSB75.DSB75 DSB75 Development Support Board designed to test and type approve Gemalto M2M modules and provide a sample configuration for application engineering. A special adapter is required to connect the ELS31-V / ELS51-V evaluation module to the DSB75.Feature Implementation

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview1.2 ELS31-V / ELS51-V System Overview5ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 5 of 351.2 ELS31-V / ELS51-V System OverviewFigure 1: ELS31-V / ELS51-V system overviewGPIO interfaceI2CUSBASC0ASC0CONTROLPOWERANTENNA (LTE dual band)ModuleSIM interface(with SIM detection)SIM cardApplicationPower supplyEmergency resetONSerial modem interfaceSerial modem interfaceI2C34452112USBAntenna /div. Antenna2GPIOs7Status LED1FST_SHDN Fast shutdown11ADC ADC1COUNTER Pulse counter1GP(I)OsHSICSDIO43HSICSDIOSPI SPI3SPI SPI2ASC1 Serial interface4

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2 Interface Characteristics17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 6 of 352 Interface CharacteristicsELS31-V / ELS51-V is equipped with an SMT application interface that connects to the external application. The SMT application interface incorporates the various application interfaces as well as the RF antenna interfaces. 2.1 Application Interface2.1.1 USB InterfaceELS31-V / ELS51-V supports a USB 2.0 High Speed (480Mbit/s) device interface that is Full Speed (12Mbit/s) compliant. The USB interface is primarily intended for use as command and data interface and for downloading firmware. The VUSB line is used for cable detection only, this is to be supplied by the external device. The USB circuitry in the ELS31-V / ELS51-V is designed to meet the USB 2.0 specification for self-power.2.0”1.Figure 2: USB circuitTo properly connect the module's USB interface to the external application, a USB 2.0 compat-ible connector and cable or hardware design is required. Furthermore, the USB modem driver distributed with ELS31-V / ELS51-V needs to be installed.1. The specification is ready for download on http://www.usb.org/developers/docs/VBUSDPDNVREG (3V075)BATT+USB_DP2)lin. reg. GNDModuleDetection only VUSB_INUSB part1)RING0Host wakeup1) It is recommended to add EMI suppression filter (see section 2.1.3.1)USB_DN2)2) If the USB interface is operated in High Speed mode (480MHz), it is recommended to take special care routing the data lines USB_DP and USB_DN. Application layout should in this case implement a differential impedance of 90Ohm for proper signal integrity.SMT

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2.1 Application Interface17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 7 of 352.1.2 Serial Interface ASC0ELS31-V / ELS51-V offers an 8-wire unbalanced, asynchronous modem interface ASC0 con-forming to ITU-T V.24 protocol DCE signalling. The electrical characteristics do not comply with ITU-T V.28. The significant levels are 0V (for low data bit or active state) and 1.8V (for high data bit or inactive state). ELS31-V / ELS51-V is designed for use as a DCE. Based on the conventions for DCE-DTE connections it communicates with the customer application (DTE) using the following signals:• Port TXD @ application sends data to the module’s TXD0 signal line• Port RXD @ application receives data from the module’s RXD0 signal lineFigure 3: Serial interface ASC0Features:• Includes the data lines TXD0 and RXD0, the status lines RTS0 and CTS0 and, in addition,the modem control lines DTR0, DSR0, DCD0 and RING0.• Configured for 8 data bits, no parity and 1 stop bit. • ASC0 can be operated at fixed bit rates from 1200bps up to 921600bps.• Supports RTS0/CTS0 hardware flow control. Communication is possible by using only RXDand TXD lines, if RTS0 is pulled low. • Wake up from SLEEP mode by RTS0 activation (high to low transition).

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2.1 Application Interface17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 8 of 352.1.3 Serial Interface ASC1 (ELS51-V Only)ELS51-V provides a 4-wire unbalanced, asynchronous modem interface ASC1 conforming toITU-T V.24 protocol DCE signalling. The electrical characteristics do not comply with ITU-TV.28. The significant levels are 0V (for low data bit or active state) and 1.8V (for high data bitor inactive state). With ELS31-V, ASC1 can only be used as data interface.ELS51-V is designed for use as a DCE. Based on the conventions for DCE-DTE connectionsit communicates with the customer application (DTE) using the following signals:• Port TXD @ application sends data to module’s TXD1 signal line• Port RXD @ application receives data from the module’s RXD1 signal lineFigure 4: Serial interface ASC1Features• Includes only the data lines TXD1 and RXD1 plus RTS1 and CTS1 for hardware hand-shake. • On ASC1 no RING line is available.• Configured for 8 data bits, no parity and 1 or 2 stop bits.• ASC1 can be operated at fixed bit rates from 1,200 bps to 921600 bps.• Supports RTS1/CTS1 hardware flow control. Communication is possible by using only RXDand TXD lines, if RTS1 is pulled low.• Wake up from SLEEP mode by RTS0 activation (high to low transition).

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2.1 Application Interface17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 9 of 352.1.4 UICC/SIM/USIM InterfaceELS31-V / ELS51-V has an integrated UICC/SIM/USIM interface compatible with the 3GPP 31.102 and ETSI 102 221. This is wired to the host interface in order to be connected to an external SIM card holder. Five pads on the SMT application interface are reserved for the SIM interface. The UICC/SIM/USIM interface supports 3V and 1.8V SIM cards. The CCIN signal serves to detect whether a tray (with SIM card) is present in the card holder. Using the CCIN signal is mandatory for compliance with the GSM 11.11 recommendation if the mechanical design of the host application allows the user to remove the SIM card during oper-ation. To take advantage of this feature, an appropriate SIM card detect switch is required on the card holder. For example, this is true for the model supplied by Molex, which has been test-ed to operate with ELS31-V / ELS51-V and is part of the Gemalto M2M reference equipment submitted for type approval. See Section 7.1 for Molex ordering numbers.Note: No guarantee can be given, nor any liability accepted, if loss of data is encountered after removing the SIM card during operation. Also, no guarantee can be given for properly initializ-ing any SIM card that the user inserts after having removed the SIM card during operation. In this case, the application must restart ELS31-V / ELS51-V.Table 1: Signals of the SIM interface (SMT application interface)Signal DescriptionGND Separate ground connection for SIM card to improve EMC.CCCLK Chipcard clockCCVCC SIM supply voltage.CCIO Serial data line, input and output.CCRST Chipcard resetCCIN Input on the baseband processor for detecting a SIM card tray in the holder. If the SIM is removed during operation the SIM interface is shut down immediately to prevent destruc-tion of the SIM. The CCIN signal is by default low and will change to high level if a SIM card is inserted.The CCIN signal is mandatory for applications that allow the user to remove the SIM card during operation. The CCIN signal is solely intended for use with a SIM card. It must not be used for any other purposes. Failure to comply with this requirement may invalidate the type approval of ELS31-V / ELS51-V.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2.1 Application Interface17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 10 of 35The figure below shows a circuit to connect an external SIM card holder.Figure 5: External UICC/SIM/USIM card holder circuitThe total cable length between the SMT application interface pads on ELS31-V / ELS51-V and the pads of the external SIM card holder must not exceed 100mm in order to meet the specifi-cations of 3GPP TS 51.010-1 and to satisfy the requirements of EMC compliance.To avoid possible cross-talk from the CCCLK signal to the CCIO signal be careful that both lines are not placed closely next to each other. A useful approach is using a GND line to shield the CCIO line from the CCCLK line.SIMCCVCCCCRSTCCIOCCCLK220nF1nFCCINV180

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2.1 Application Interface17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 11 of 352.1.5 GPIO InterfaceELS31-V / ELS51-V offers a GPIO interface with 17 GPIO and 3 GPO lines. The lines areshared with other interfaces or functions: Fast shutdown (see Section 2.1.11.2), status LED(see Section 2.1.11.1), a pulse counter (see Section 2.1.8), ASC0 (see Section 2.1.2), ASC1(see Section 2.1.3), SPI (see Section 2.1.7), and HSIC (see Section 2.1.9).The following table shows the configuration variants for the GPIO pads. All variants are mutu-ally exclusive, i.e. a pad configured for instance as Status LED is locked for alternative usage.After startup, the above mentioned alternative GPIO line assignments can be configured usingAT commands (see [1]). The configuration is non-volatile and available after module restart.Notes:• GPO5, GPO23 and GPO26 are GPOs only.Table 2: GPIO lines and possible alternative assignmentGPIO Fast Shutdown Status LED Pulse Counter ASC0 ASC1 SPI HSICGPIO1 DTR0GPIO2 DCD0GPIO3 DSR0GPIO4 FST_SHDNGPO5 LEDGPIO6GPIO7GPIO8 COUNTERGPIO16 RXD1 AP_WAKEUPGPIO17 TXD1 HOST_ACTIVEGPIO18 RTS1 CP_WAKEUPGPIO19 CTS1 SUSPENDGPIO20GPIO21GPIO22GPO23GPIO24 RING0GPIO25GPO26 SPI_CS1GPIO27 SPI_CS2

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2.1 Application Interface17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 12 of 352.1.6 I2C InterfaceI2C is a serial, 8-bit oriented data transfer bus for bit rates up to 400kbps in Fast mode. It con-sists of two lines, the serial data line I2CDAT and the serial clock line I2CCLK. The module actsas a single master device, e.g. the clock I2CCLK is driven by the module. I2CDAT is a bi-direc-tional line. Each device connected to the bus is software addressable by a unique 7-bit ad-dress, and simple master/slave relationships exist at all times. The module operates as master-transmitter or as master-receiver. The customer application transmits or receives data only onrequest of the module.The I2C interface can be powered via the V180 line of ELS31-V / ELS51-V. If connected to theV180 line, the I2C interface will properly shut down when the module enters the Power Downmode.Note: Good care should be taken when creating the PCB layout of the host application: Thetraces of I2CCLK and I2CDAT should be equal in length and as short as possible.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2.1 Application Interface17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 13 of 352.1.7 SPI InterfaceFour ELS31-V / ELS51-V GPIO interface lines can be configured as Serial Peripheral Interface(SPI). The SPI is a synchronous serial interface for control and data transfer between ELS31-V / ELS51-V and the external application. Only one application can be connected to the SPIand the interface supports only master mode. The transmission rates are up to 6.5Mbit/s. TheSPI interface comprises the two data lines MOSI and MISO, the clock line SPI_CLK a well asthe chip select lines SPI_CS1 and SPI_CS2.2.1.8 Pulse CounterThe GPIO8 line can be configured as pulse counter line COUNTER. The pulse counter inter-face can be used, for example, as a clock (for GPIOs see Section 2.1.5). 2.1.9 HSIC Interface (ELS51-V Only)TBD2.1.10 SDIO Interface (ELS51-V Only)TBD2.1.11 Control Signals2.1.11.1 Status LEDThe GPO5 interface line can be configured to drive a status LED that indicates different oper-ating modes of the module (for GPIOs see Section 2.1.5). GPO and LED functionality are mu-tually exclusive.2.1.11.2 Fast ShutdownThe GPIO4 interface line can be configured as fast shutdown signal line FST_SHDN. The con-figured FST_SHDN line is an active low control signal.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2.2 RF Antenna Interface17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 14 of 352.2 RF Antenna InterfaceThe RF interface has an impedance of 50. ELS31-V /ELS51-V is capable of sustaining a total mismatch at the antenna line without any damage, even when transmitting at maximum RF power.The external antenna must be matched properly to achieve best performance regarding radi-ated power, modulation accuracy and harmonic suppression. Antenna matching networks are not included on the ELS31-V / ELS51-V module and should be placed in the host application if the antenna does not have an impedance of 50.Regarding the return loss ELS31-V / ELS51-V provides the following values in the active band:Table 3: Return loss in the active bandState of module Return loss of module Recommended return loss of applicationReceive > 8dB > 12dBTransmit not applicable > 12dB

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2.2 RF Antenna Interface17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 15 of 352.2.1 Antenna InstallationThe antenna is connected by soldering the antenna pads (RF_OUT, pad #59 and DIV_ANT, pad 56) its neighboring ground pads (GND, i.e., pads #55, #57, #58 and #60) directly to the application’s PCB. The antenna pad is the antenna reference point (ARP) for ELS31-V / ELS51-V. All RF data specified throughout this document is related to the ARP.The distance between the antenna RF pads and its neighboring GND pads has been optimized for best possible impedance. On the application PCB, special attention should be paid to these 3 pads, in order to prevent mismatch.The wiring of the antenna connection line, starting from the antenna pad to the application an-tenna should result in a 50 line impedance. Line width and distance to the GND plane needs to be optimized with regard to the PCB’s layer stack. To prevent receiver desensitization due to interferences generated by fast transients like high speed clocks on the application PCB, it is recommended to realize the antenna connection line using embedded Stripline rather than Micro-Stripline technology. For type approval purposes, the use of a 50 coaxial antenna connector (U.FL-R-SMT) might be necessary. In this case the U.FL-R-SMT connector should be placed as close as possible to ELS31-V / ELS51-V‘s antenna pad.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2.3 Sample Application17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 16 of 352.3 Sample ApplicationFigure 6 shows a typical example of how to integrate a ELS31-V / ELS51-V module with anapplication. Usage of the various host interfaces depends on the desired features of the appli-cation.Because of the high RF field density inside the module, it cannot be guaranteed that no selfinterference might occur, depending on frequency and the applications grounding concept. Thepotential interferers may be minimized by placing small capacitors (47pF) at suspected lines(e.g. RXD0, VDDLP, and ON). While developing SMT applications it is strongly recommended to provide test pointsfor certain signals, i.e., lines to and from the module - for debug and/or test purposes.The SMT application should allow for an easy access to these signals. For details onhow to implement test points see [4].The EMC measures are best practice recommendations. In fact, an adequate EMC strategy foran individual application is very much determined by the overall layout and, especially, the po-sition of components. For example, mounting the internal acoustic transducers directly on thePCB eliminates the need to use the ferrite beads shown in the sample schematic. Note: ELS31-V / ELS51-V is not intended for use with cables longer than 3m.DisclaimerNo warranty, either stated or implied, is provided on the sample schematic diagram shown inFigure 6 and the information detailed in this section. As functionality and compliance with na-tional regulations depend to a great amount on the used electronic components and the indi-vidual application layout manufacturers are required to ensure adequate design and operatingsafeguards for their products using ELS31-V / ELS51-V modules.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview2.3 Sample Application17ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 17 of 35Figure 6: Schematic diagram of ELS31-V / ELS51-V sample applicationELS31-V/51-VMain AntennaDiv. AntennaBATT+RFBATT+BBGPIOsLEDPWMCOUNTERI2CCLKI2CDATGNDSDIOHSICONFST_SHUTDOWNASC0ASC1USBV180CCINCCVCCCCIOCCRSTCCCLKPower Supply33pF 33pF + 150µFLow ESR!2k2 2k2V180BlockingWiFiµC1nF 10pF10pF220nFSIMUSBInterfaces available only on ELS51-V

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview3 Operating Characteristics19ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 18 of 353 Operating Characteristics3.1 Operating ModesThe table below briefly summarizes the various operating modes referred to throughout the document. Table 4: Overview of operating modesMode FunctionNormal opera-tionLTE IDLE No data transfer is in progress and the USB connection is suspended by host (or is not present) and no active communication via ASC0/ASC1. In IDLE mode, the software can be active or in SLEEP state.LTE DATA LTE data transfer in progress. Power consumption depends on network settings and data transfer rate. Power Down Normal shutdown after sending the power down command. Software is not active. Inter-faces are not accessible. Operating voltage remains applied.Airplane mode Airplane mode shuts down the radio part of the module, causes the module to log off from the LTE network and disables all AT commands whose execution requires a radio connec-tion.Airplane mode can be controlled by AT command (see [1]).In Airplane mode, the software can be active or in SLEEP state.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview3.2 Power Supply19ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 19 of 353.2 Power SupplyELS31-V/ ELS51-V needs to be connected to a power supply at the SMT application interface - 2 BATT lines and GND. There are two separate voltage domains for BATT:• BATT_BB with a line mainly for the baseband power supply.• BATT_RF with a line for the RF power amplifier supply.Please note that throughout the document BATT refers to both voltage domains and power supply lines - BATT_BB and BATT_RF.The power supply of ELS31-V / ELS51-V has to be a single voltage source at BATT_BB and BATT_RF. It must be able to provide the current for all operation modes of the module. All the key functions for supplying power to the device are handled by the power management section of the analog controller. This IC provides the following features:• Stabilizes the supply voltages for the baseband using low drop linear voltage regulators anda DC-DC step down switching regulator.• Switches the module's power voltages for the power-up and -down procedures.• SIM switch to provide SIM power supply.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview4 Mechanical Dimensions, Mounting and Packaging21ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 20 of 354 Mechanical Dimensions, Mounting and Packaging4.1 Mechanical Dimensions of ELS31-V / ELS51-VFigure 7 shows the top and bottom view of ELS31-V / ELS51-V and provides an overview of the board's mechanical dimensions. For further details see Figure 8. Figure 7: ELS31-V– top and bottom viewProduct labelTop viewBottom view

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview4.1 Mechanical Dimensions of ELS31-V / ELS51-V21ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 21 of 35Figure 8: Dimensions of ELS31-V / ELS51-V (all dimensions in mm)Figure 9: Dimensions of ELS31-V / ELS51-V (all dimensions in mm) - bottom view

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview5 Regulatory and Type Approval Information27ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 22 of 355 Regulatory and Type Approval Information5.1 Directives and StandardsELS31-V / ELS51-V is designed to comply with the directives and standards listed below.It is the responsibility of the application manufacturer to ensure compliance of the final product with all provisions of the applicable directives and standards as well as with the technical spec-ifications provided in the "ELS31-V / ELS51-V Hardware Interface Description".Table 5: Directives2002/95/EC (RoHS 1)2011/65/EC (RoHS 2) Directive of the European Parliament and of the Council of 27 January 2003 (and revised on 8 June 2011) on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS)Table 6: Standards of North American type approvalCFR Title 47 Code of Federal Regulations, Part 22 and Part 24 (Telecommunications, PCS); US Equipment Authorization FCCOET Bulletin 65 (Edition 97-01) Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic FieldsUL 60 950-1 Product Safety Certification (Safety requirements)California Leadfree Man-date Covered by European RoHS requirementsRSS132 (Issue2)RSS133 (Issue5) Canadian StandardTable 7: Standards of Verizon type approvalVerizon Wireless Unified Module Process for Compliance Testing and Approval, October 2014Verizon Wireless Device Requirements LTE 3GPP Band 13 Network Access, October 2014Verizon Wireless Device Requirements LTE 3GPP Band 4 Network Access, October 20143GPP2 C.S0015-A v1.0 Short Message Service for spread spectrum systemsTable 8: Standards of GCF type approval3GPP TS 51.010-1 Digital cellular telecommunications system (Release 10); Mobile Station (MS) conformance specification;GCF-CC V3.58 Global Certification Forum - Certification CriteriaTable 9: Requirements of qualityIEC 60068 Environmental testingDIN EN 60529 IP codes

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview5.1 Directives and Standards27ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 23 of 35Table 11: Toxic or hazardous substances or elements with defined concentration limitsTable 10: Standards of the Ministry of Information Industry of the People’s Republic of ChinaSJ/T 11363-2006 “Requirements for Concentration Limits for Certain Hazardous Sub-stances in Electronic Information Products” (2006-06).SJ/T 11364-2006 “Marking for Control of Pollution Caused by Electronic Information Products” (2006-06).According to the “Chinese Administration on the Control of Pollution caused by Electronic Information Products” (ACPEIP) the EPUP, i.e., Environmental Protection Use Period, of this product is 20 years as per the symbol shown here, unless otherwise marked. The EPUP is valid only as long as the product is operated within the operating limits described in the Gemalto M2M Hardware Interface Description.Please see Table 11 for an overview of toxic or hazardous substances or elements that might be contained in product parts in concentrations above the limits defined by SJ/T 11363-2006.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview5.2 SAR requirements specific to portable mobiles27ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 24 of 355.2 SAR requirements specific to portable mobilesMobile phones, PDAs or other portable transmitters and receivers incorporating a GSM module must be in accordance with the guidelines for human exposure to radio frequency energy. This requires the Specific Absorption Rate (SAR) of portable ELS31V / ELS51-V based applications to be evaluated and approved for compliance with national and/or international regulations. Since the SAR value varies significantly with the individual product design manufacturers are advised to submit their product for approval if designed for portable use. For US markets the relevant directives are mentioned below. It is the responsibility of the manufacturer of the final product to verify whether or not further standards, recommendations or directives are in force outside these areas. Products intended for sale on US marketsES 59005/ANSI C95.1 Considerations for evaluation of human exposure to Electromagnetic Fields (EMFs) from Mobile Telecommunication Equipment (MTE) in thefrequency range 30MHz - 6GHz Please note that SAR requirements are specific only for portable devices and not for mobile devices as defined below:• Portable device:A portable device is defined as a transmitting device designed to be used so that the radi-ating structure(s) of the device is/are within 20 centimeters of the body of the user.• Mobile device:A mobile device is defined as a transmitting device designed to be used in other than fixedlocations and to generally be used in such a way that a separation distance of at least 20centimeters is normally maintained between the transmitter's radiating structure(s) and thebody of the user or nearby persons. In this context, the term ''fixed location'' means that thedevice is physically secured at one location and is not able to be easily moved to anotherlocation.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview5.3 Reference Equipment for Type Approval27ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 25 of 355.3 Reference Equipment for Type ApprovalThe Gemalto M2M reference setup submitted to type approve ELS31-V / ELS51-V(including a special approval adapter for the DSB75) is shown in the following figure1:Figure 10: Reference equipment for Type Approval1. For RF performance tests a mini-SMT/U.FL to SMA adapter with attached 6dB coaxial attenuator is cho-sen to connect the evaluation module directly to the GSM/UMTS test equipment instead of employingthe SMA antenna connectors on the ELS31-V- / ELS51-V-DSB75 adapter as shown in Figure 10. Thefollowing products are recommended:Hirose SMA-Jack/U.FL-Plug conversion adapter HRMJ-U.FLP(40)(for details see see http://www.hirose-connectors.com/ or http://www.farnell.com/Aeroflex Weinschel Fixed Coaxial Attenuator Model 3T/4T(for details see http://www.aeroflex.com/ams/weinschel/pdfiles/wmod3&4T.pdf)AntennaGSM / GPRS / UMTS Antenna with 1m cable ASC0PCPower supplyLTEBase stationDSB75ASC1USBApproval adapter for DSB75SMAEvaluation moduleELS31-VELS51-VUSBEvaluation moduleELS31-VELS51-VSIM cardTop viewBottom view

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview5.4 Compliance with FCC and IC Rules and Regulations27ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 26 of 355.4 Compliance with FCC and IC Rules and RegulationsThe Equipment Authorization Certification for the Gemalto M2M reference application de-scribed in Section 5.3 will be registered under the following identifiers:• ELS31-V:FCC Identifier: QIPELS31-V (not yet granted)Industry Canada Certification Number: 7830A-ELS31V (not yet granted)Granted to Gemalto M2M GmbH • ELS51-V:FCC Identifier: QIPELS51-V (not yet granted)Industry Canada Certification Number: 7830A-ELS51V (not yet granted)Granted to Gemalto M2M GmbH Manufacturers of mobile or fixed devices incorporating ELS31-V / ELS51-V modules are au-thorized to use the FCC Grants and Industry Canada Certificates of the ELS31-V / ELS51-V modules for their own final products according to the conditions referenced in these docu-ments. In this case, an FCC/ IC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains FCC ID: QIPELS31-V" / "Contains FCC ID: QIPELS51-V", and accordingly “Contains IC: 7830A-ELS31V“ / “Contains IC: 7830A-ELS51V“. The integration is limited to fixed or mobile categorised host devices, where a separation dis-tance between the antenna and any person of min. 20cm can be assured during normal oper-ating conditions.For mobile and fixed operation configurations the antenna gain, including cable loss, must not exceed the limits in the following Table 12 for FCC and IC.IMPORTANT: Manufacturers of portable applications incorporating ELS31V / ELS51-V modules are required to have their final product certified and apply for their own FCC Grant and Industry Canada Cer-tificate related to the specific portable mobile. This is mandatory to meet the SAR requirements for portable mobiles (see Section 5.2 for detail).Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). These limits are designed to provide reasonable protection against harmful inter-ference in a residential installation. This equipment generates, uses and can radiate radio fre-quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference Table 12: Antenna gain limits for FCC and ICOperating band FCC limit IC limit UnitMaximum gain in lower operating bands with f< 1GHz(LTE Bd13)10.4 7.4 dBiMaximum gain in higher operating bands with f=1700MHz(LTE Bd4)6.5 6.5 dBi

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview5.4 Compliance with FCC and IC Rules and Regulations27ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 27 of 35will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.• Consult the dealer or an experienced radio/TV technician for help.This Class B digital apparatus complies with Canadian ICES-003.If Canadian approval is requested for devices incorporating ELS31V / ELS51-V modules the above note will have to be provided in the English and French language in the final user docu-mentation. Manufacturers/OEM Integrators must ensure that the final user documentation does not contain any information on how to install or remove the module from the final product.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview6 Document Information32ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 28 of 356 Document Information6.1 Revision HistoryNew document: "Cinterion® ELS31-V/ELS51-V Hardware Interface Overview" v00.5026.2 Related Documents[1] ELS31-V / ELS51-V AT Command Set[2] ELS31-V / ELS51-V Release Note[3] Application Note 40: Thermal Solutions[4] Application Note 48: SMT Module Integration[5] Universal Serial Bus Specification Revision 2.0, April 27, 20006.3 Terms and AbbreviationsChapter What is new-- Initial document setup.Abbreviation DescriptionADC Analog-to-digital converterAGC Automatic Gain ControlANSI American National Standards InstituteARFCN Absolute Radio Frequency Channel NumberARP Antenna Reference PointASC0/ASC1 Asynchronous Controller. Abbreviations used for first and second serial interface of the modueB Thermistor ConstantBER Bit Error RateBTS Base Transceiver StationCB or CBM Cell Broadcast MessageCE Conformité Européene (European Conformity)CHAP Challenge Handshake Authentication ProtocolCPU Central Processing UnitCS Coding SchemeCSD Circuit Switched DataCTS Clear to SendDAC Digital-to-Analog Converter

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview6.3 Terms and Abbreviations32ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 29 of 35DAI Digital Audio InterfacedBm0 Digital level, 3.14dBm0 corresponds to full scale, see ITU G.711, A-lawDCE Data Communication Equipment (typically modems, e.g. Gemalto M2M module)DCS 1800 Digital Cellular System, also referred to as PCNDRX Discontinuous ReceptionDSB Development Support BoxDSP Digital Signal ProcessorDSR Data Set ReadyDTE Data Terminal Equipment (typically computer, terminal, printer or, for example, GSM application)DTR Data Terminal ReadyDTX Discontinuous TransmissionEFR Enhanced Full RateEGSM Enhanced GSMEIRP Equivalent Isotropic Radiated PowerEMC Electromagnetic CompatibilityERP Effective Radiated PowerESD Electrostatic DischargeETS European Telecommunication StandardFCC Federal Communications Commission (U.S.)FDMA Frequency Division Multiple AccessFR Full RateGMSK Gaussian Minimum Shift KeyingGPIO General Purpose Input/OutputGPRS General Packet Radio ServiceGSM Global Standard for Mobile CommunicationsHiZ High ImpedanceHR Half RateI/O Input/OutputIC Integrated CircuitIMEI International Mobile Equipment IdentityISO International Standards OrganizationITU International Telecommunications Unionkbps kbits per secondLED Light Emitting DiodeLi-Ion/Li+ Lithium-IonLi battery Rechargeable Lithium Ion or Lithium Polymer batteryLTE Long Term EvolutionAbbreviation Description

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview6.3 Terms and Abbreviations32ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 30 of 35Mbps Mbits per secondMMI Man Machine InterfaceMO Mobile OriginatedMS Mobile Station (GSM module), also referred to as TEMSISDN Mobile Station International ISDN numberMT Mobile TerminatedNTC Negative Temperature CoefficientOEM Original Equipment ManufacturerPA Power AmplifierPAP Password Authentication ProtocolPBCCH Packet Switched Broadcast Control ChannelPCB Printed Circuit BoardPCL Power Control LevelPCM Pulse Code ModulationPCN Personal Communications Network, also referred to as DCS 1800PCS Personal Communication System, also referred to as GSM 1900PDU Protocol Data UnitPLL Phase Locked LoopPPP Point-to-point protocolPSK Phase Shift KeyingPSU Power Supply UnitPWM Pulse Width ModulationR&TTE Radio and Telecommunication Terminal EquipmentRAM Random Access MemoryRF Radio FrequencyRLS Radio Link StabilityRMS Root Mean Square (value)RoHS Restriction of the use of certain hazardous substances in electrical and electronic equipment. ROM Read-only MemoryRTC Real Time ClockRTS Request to SendRx Receive DirectionSAR Specific Absorption RateSAW Surface Accoustic WaveSELV Safety Extra Low VoltageSIM Subscriber Identification ModuleSMD Surface Mount DeviceAbbreviation Description

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview6.3 Terms and Abbreviations32ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 31 of 35SMS Short Message ServiceSMT Surface Mount TechnologySRAM Static Random Access MemoryTA Terminal adapter (e.g. GSM module)TDMA Time Division Multiple AccessTE Terminal Equipment, also referred to as DTETLS Transport Layer SecurityTx Transmit DirectionUART Universal asynchronous receiver-transmitterURC Unsolicited Result CodeUSSD Unstructured Supplementary Service DataVSWR Voltage Standing Wave RatioAbbreviation Description

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview6.4 Safety Precaution Notes32ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 32 of 356.4 Safety Precaution NotesThe following safety precautions must be observed during all phases of the operation, usage, service or repair of any cellular terminal or mobile incorporating ELS31-V. Manufacturers of the cellular terminal are advised to convey the following safety information to users and operating personnel and to incorporate these guidelines into all manuals supplied with the product. Fail-ure to comply with these precautions violates safety standards of design, manufacture and in-tended use of the product. Gemalto M2M assumes no liability for customer’s failure to comply with these precautions.When in a hospital or other health care facility, observe the restrictions on the use of mobiles. Switch the cellular terminal or mobile off, if instructed to do so by the guide-lines posted in sensitive areas. Medical equipment may be sensitive to RF energy. The operation of cardiac pacemakers, other implanted medical equipment and hear-ing aids can be affected by interference from cellular terminals or mobiles placed close to the device. If in doubt about potential danger, contact the physician or the manufac-turer of the device to verify that the equipment is properly shielded. Pacemaker patients are advised to keep their hand-held mobile away from the pacemaker, while it is on. Switch off the cellular terminal or mobile before boarding an aircraft. Make sure it can-not be switched on inadvertently. The operation of wireless appliances in an aircraft is forbidden to prevent interference with communications systems. Failure to observe these instructions may lead to the suspension or denial of cellular services to the offender, legal action, or both.Do not operate the cellular terminal or mobile in the presence of flammable gases or fumes. Switch off the cellular terminal when you are near petrol stations, fuel depots, chemical plants or where blasting operations are in progress. Operation of any elec-trical equipment in potentially explosive atmospheres can constitute a safety hazard.Your cellular terminal or mobile receives and transmits radio frequency energy while switched on. Remember that interference can occur if it is used close to TV sets, radios, computers or inadequately shielded equipment. Follow any special regulations and always switch off the cellular terminal or mobile wherever forbidden, or when you suspect that it may cause interference or danger.Road safety comes first! Do not use a hand-held cellular terminal or mobile when driv-ing a vehicle, unless it is securely mounted in a holder for speakerphone operation. Before making a call with a hand-held terminal or mobile, park the vehicle. Speakerphones must be installed by qualified personnel. Faulty installation or opera-tion can constitute a safety hazard.IMPORTANT!Cellular terminals or mobiles operate using radio signals and cellular networks. Because of this, connection cannot be guaranteed at all times under all conditions. Therefore, you should never rely solely upon any wireless device for essential com-munications, for example emergency calls. Remember, in order to make or receive calls, the cellular terminal or mobile must be switched on and in a service area with adequate cellular signal strength. Some networks do not allow for emergency calls if certain network services or phone features are in use (e.g. lock functions, fixed dialing etc.). You may need to deactivate those features before you can make an emergency call.Some networks require that a valid SIM card be properly inserted in the cellular termi-nal or mobile.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview7 Appendix34ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 33 of 357 Appendix7.1 List of Parts and AccessoriesTable 13: List of parts and accessoriesDescription Supplier Ordering informationELS31-V Gemalto M2M Standard module Gemalto M2M IMEI:Packaging unit (ordering) number:L30960-N4500-A200Module label number:S30960-S4500-A200-1ELS51-V Gemalto M2M Standard module Gemalto M2M IMEI:Packaging unit (ordering) number:L30960-N4530-A100Module label number:S30960-S4530-A100-1ELS31-V Evaluation Module Gemalto M2M Ordering number: L30960-N4501-A200ELS51-V Evaluation Module Gemalto M2M Ordering number: L30960-N4531-A100DSB75 Evaluation Kit Gemalto M2M Ordering number: L36880-N8811-A100DSB MiniCompact Evaluation Board Gemalto M2M Ordering number: L30960-N0030-A100Starter Kit B80 Gemalto M2M Ordering Number L30960-N0040-A100Multi-Adapter R1 for mount-ing ELS31-V/ELS51-V evalu-ation modules onto DSB75Gemalto M2M Ordering number: L30960-N0010-A100Approval adapter for mount-ing ELS31-V/ELS51-V evalu-ation modules onto DSB75Gemalto M2M Ordering number: L30960-N2301-A100SIM card holder incl. push button ejector and slide-in trayMolex Ordering numbers: 91228 91236Sales contacts are listed in Table 14.

Cinterion® ELS31-V/ELS51-V Hardware Interface Overview7.1 List of Parts and Accessories34ELS31-V_ELS51-V_HIO_v00.502 2015-12-07Confidential / PreliminaryPage 34 of 35Table 14: Molex sales contacts (subject to change)MolexFor further information please click:http://www.molex.comMolex Deutschland GmbHOtto-Hahn-Str. 1b69190 WalldorfGermanyPhone: +49-6227-3091-0Fax: +49-6227-3091-8100Email: mxgermany@molex.comAmerican HeadquartersLisle, Illinois 60532U.S.A.Phone: +1-800-78MOLEXFax: +1-630-969-1352Molex China DistributorsBeijing, Room 1311, Tower B, COFCO PlazaNo. 8, Jian Guo Men Nei Street, 100005BeijingP.R. ChinaPhone: +86-10-6526-9628 Fax: +86-10-6526-9730Molex Singapore Pte. Ltd.110, International RoadJurong Town, Singapore 629174Phone: +65-6-268-6868Fax: +65-6-265-6044Molex Japan Co. Ltd.1-5-4 Fukami-Higashi,Yamato-City,Kanagawa, 242-8585 JapanPhone: +81-46-265-2325Fax: +81-46-265-2365

Navigation menu

Upload a User Manual

Namespaces

Wiki Guide
HTML
PDF
Info

Views

User Manual
Discussion / Help

Navigation

© 2024 UserManual.wiki | Privacy Policy

Contact Us
DMCA