TCL Technoly Electronics PS000023 Auvio Stereo Bluetooth Speaker User Manual

TCL Technoly Electronics (Huizhou) Co., Ltd. Auvio Stereo Bluetooth Speaker

User Manual

2 3 4 5 6 7 8 9stereo bluetooth® speakerWe hope you enjoy your AUVIO Stereo Bluetooth Speaker with True Wireless stereo sound capability. This water-resistant speaker is designed with a built-in mic and speakerphone so you can take calls as well as listen to music from your smartphone. Please read this user's guide before using your new speaker.Package Contents • Speaker • USB Charging Cable • User’s GuideSpecificationsBattery .................Rechargeable 3.7V / 700mAh lithium polymer Battery Charging Voltage ..........................................DC 5V, 500mACharging Time ............................................................. approx. 4 hoursPlay Time ............................................................................ up to 5 hoursFrequency Response .............................. (speaker) 110 Hz – 20 kHzOutput Power.................................................................................2 × 3WImpedance ................................................................................... 4 OhmsDriver ................................................. 2 × 1.5 in" (38mm) neodymiumBluetooth Protocol .............. V4.2 with A2DP, AVRCP, HFP ProfileOperation Range ................................................................ 33 ft. (10m)Water resistance ...............................................................................IPX5Specifications are subject to change and improvement without notice. Actual product may vary from the images found in this document.Charge Your Speaker1. Lift the cover on the side to access the jacks. Then connect the supplied charging cable to the DC IN jack and a USB power source. G LED lights red during charging and turns o when fully charged.2. Unplug after charging, and rmly replace the cover to protect the jacks from water, dust or dirt.User’s Guide4000768 / 4000769Notes: • The speaker will disconnect and power down from your device if they are too far apart, or left idle. To reconnect, move the speaker closer to the device within 3 minutes. • The last volume setting used on the speaker is memorized after switching o. • Music playback is paused during call functions and resumes when the call is ended.Clear Bluetooth PairingYour speaker automatically reconnects to the most recently paired device when switched on. If you want to change to other Bluetooth devices, or in case of problems pairing, press G and hold + for 3 seconds. Multipoint ConnectionThis speaker is multipoint-enabled. This allows you to easily access and play music or take a call through the speaker from either one of two connected Bluetooth devices.1. To use multipoint, make sure you pair each of your devices separately. See Pairing a Bluetooth Device.2. There is no need to switch o the speaker to pair your second device. Press and hold / 2 seconds to start Bluetooth pairing your second device. Bluetooth status on your rst device will automatically disconnect.3. After your second device is successfully paired and connected, to enjoy multipoint, go to the Bluetooth menu on your rst device to reactivate Bluetooth connection status. Both your devices are now connected.Side ViewDC INConnect the included USB charging cable here to charge. AUXFor line-in listening option. /Call functions on speakerphoneStart/disconnect Bluetooth pairingAnswer, end, reject and switch between callsIndicator Flashes quickly - pairing / incoming call, connecting Bluetooth / True WirelessLights steadily - Bluetooth connected, engaged in callUsing True Wireless ModeTo play your music from your smartphone or other Bluetooth-enabled device, for best sound performance you'll need an additional AUVIO BTS300 speaker. Conveniently, there is no need to pair the second speaker.True Wireless ActivationBefore you start activation or when using True Wireless mode, make sure of the following: • Your rst speaker is paired before you setup True Wireless mode. • Both speakers are on and in stop mode. • If you are using multipoint connection, you need to turn o multipoint on one of your 2 Bluetooth devices.1. Press the button on one speaker. The / indicator ash quickly.2. On another speaker, press the button, the / indicators ash quickly.3. When True Wireless is successfully activated, the a nd / indicators light steadily on both your speakers.4. To swap left/right channel sound on your two speakers, press and hold button for 2 seconds on either speaker. 5. To exit True Wireless, press the button on either speaker. Notes: • Smart Power O: During True Wireless playback, press and hold G on either speaker for 2 seconds to switch o both speakers simultaneously. • Smart True Wireless: Once activated, True Wireless is memorized by your speakers. True Wireless is the default playback mode when you next switch on the two speakers. •Troubleshooting TW Activation: In case of diculty activating, turn o each speaker. Then switch the rst speaker on again, followed by the second speaker, and start playing a song. Wait a few seconds to hear if True Wireless has been activated. If not, repeat True Wireless Activation and complete steps 1-3 above within 3 minutes. Connecting with AUXFor device players without Bluetooth functionality, use an ⅛" (3.5mm) audio cable (not included) to connect to the speaker’s AUX jack.Note: Bluetooth functionality is automatically deactivated when AUX has been played music.Resetting the SpeakerIn case the speaker's buttons are not functioning properly during operation, press and hold + and - at the same time for 5 seconds to reset and switch o the speaker. Any previous TW activation will not be lost. FCC InformationThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and To... Button PressTurn on/ o speaker G...and hold 2 secStart Bluetooth pairing /Disconnect Bluetooth pairingVolume up/ down +/ −...quickly, or press and holdCallsAnswer/ end call /×1Reject an incoming call /...and hold 2 secSwitch to an incoming call and end the current callTrue Wireless (TW)Activate on rst speaker×1Activate on 2nd speakerDeactivate True WirelessSwap left/ right channel ...and hold 2 secControls Overview+/−Adjust volumeon, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. • Consult your dealer or an experienced radio/TV technician for help.If you cannot eliminate the interference, the FCC requires that you stop using your equipment. Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Limited WarrantyGo to www.radioshack.com/help for details.RadioShack Customer Relations300 RadioShack Circle, Fort Worth, TX 76102G Turn on/o speakerIndicatorRed - ChargingFlashes red slowly - low batteryActivate / deactivate Tru e Wire lessSwap L/R channels when two speakers are connectedIndicator Lights steadily - True Wireless activated© 2016 General Wireless Operations Inc.All rights reserved. AUVIO is a registered trademark used by General Wireless Operations Inc. dba RadioShack.07A164000768 4000769Printed in China Complies with the European Union’s “Restriction of Hazardous Substances Directive,” which protects the environment by restricting specic hazardous materials and products.www.radioshack.comNotes: • You can charge the speaker and use it at the same time. • When the battery is low, the G LED ashes red slowly, and the speaker will eventually automatically turn o.Lithium Battery Notes: • Charge batteries on a reproof surface away from ammable items or liquids. Follow the instructions for charging the speaker and do not charge longer than recommended. • Recycle lithium batteries. Do not dispose of them in the trash. Do not burn or bury batteries. Do not puncture or crush. Do not disassemble. • If the electrolyte in the cells should get on your skin, thoroughly wash with soap and water. If in the eyes, rinse thoroughly with cool water. Immediately seek medical attention.Pairing to a Bluetooth Device1. Press and hold G for 2 seconds to turn on the speaker. The / LED ashes blue quickly as your speaker searches for Bluetooth devices.2. When pairing to a device for the rst time, press and hold / for 2 seconds to start Bluetooth pairing.3. Activate your device’s Bluetooth function (refer to your device’s user’s guide). When your device locates AUVIO BTS300, select this from the device list. When paired, the / indicator lights blue steadily.4. Use the controls on your device to play music. To adjust volume, you can use the speaker's +/− buttons, or your device's controls.The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by General Wireless Operations Inc. is under license.AUX4000768_69_UG_EN.062216.indd All Pages 7/5/2016 11:35:22 AM

Navigation menu