Symbol Technologies MC18N0 MC18 Personal Shopper - Barcode Scanner User Manual

Symbol Technologies Inc MC18 Personal Shopper - Barcode Scanner

UserManual.wiki >

Symbol Technologies >

MC18N0 User Manual >

User Manual (1 of 2).pdf

MC18Product Reference GuideMN000834A01Rev. AJune 2014

ii MC18 Product Reference Guide© 2014 by Symbol Technologies, Inc. All rights reserved.No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Symbol Technologies. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. Symbol Technologies grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Symbol Technologies. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a licensed program in a network without written permission from Symbol Technologies. The user agrees to maintain Symbol Technologies copyright notice on the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof.Symbol Technologies reserves the right to make changes to any software or product to improve reliability, function, or design.Symbol Technologies does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.No license is granted, either expressly or by implication, estoppel, or otherwise under any Symbol Technologies, Inc., intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in Symbol Technologies products.

iiiRevision HistoryChanges to the original manual are listed below:Change Date Description01 Rev. A 06/27/14 Initial release.

TABLE OF CONTENTSRevision History.............................................................................................................................. iiAbout This GuideIntroduction ..................................................................................................................................... xiDocumentation Set ................................................................................................................... xiConfigurations................................................................................................................................. xiiSoftware Versions..................................................................................................................... xiiiOEM Software........................................................................................................................... xiiiFusion Software........................................................................................................................ xiiiChapter Descriptions ...................................................................................................................... xivNotational Conventions................................................................................................................... xvRelated Documents and Software .................................................................................................. xvService Information......................................................................................................................... xviChapter 1: Getting StartedIntroduction .................................................................................................................................... 1-1Unpacking ...................................................................................................................................... 1-1Features ......................................................................................................................................... 1-2Accessories ................................................................................................................................... 1-4LED Indicators ............................................................................................................................... 1-5Keypad ........................................................................................................................................... 1-5Getting Started ............................................................................................................................... 1-6 Connecting the Battery ................................................................................................................. 1-6Charging the Battery ................................................................................................................ 1-9Manual Release of MC18 from the Cradle ............................................................................... 1-10Software Release of MC18 from the Cradle ............................................................................ 1-11Starting the MC18 .......................................................................................................................... 1-12Touch Screens ............................................................................................................................... 1-13Data Capture ................................................................................................................................. 1-13Scanning Considerations ......................................................................................................... 1-13Scanning Bar Codes ................................................................................................................ 1-13Scanning Tips .................................................................................................................... 1-14LED Indications ........................................................................................................................ 1-14

vi MC18 Product Reference GuideResetting the MC18 ....................................................................................................................... 1-15Performing a Warm Boot ......................................................................................................... 1-15Performing a Cold Boot ............................................................................................................ 1-15Replacing the Bezel ....................................................................................................................... 1-16Chapter 2: Staging and ProvisioningIntroduction .................................................................................................................................... 2-1Staging ........................................................................................................................................... 2-1Bar Code Staging ..................................................................................................................... 2-2On-Demand Staging ................................................................................................................ 2-4ActiveSync Connection Mode ............................................................................................ 2-4Already existing IP Connection Mode ................................................................................ 2-4Well-known WLAN Connection Mode ................................................................................ 2-4RD Client Main Menu ............................................................................................................... 2-6Client Info ........................................................................................................................... 2-6Log Menu ........................................................................................................................... 2-7View Log ............................................................................................................................ 2-7View Job Log ..................................................................................................................... 2-8Set Log Level ..................................................................................................................... 2-8Set Job Log Level .............................................................................................................. 2-9Package List ...................................................................................................................... 2-9Provisioning ................................................................................................................................... 2-11MSP Agent ............................................................................................................................... 2-11MSP Agent Main Menu ............................................................................................................ 2-11Monitor Processing ............................................................................................................ 2-12Force Check-In .................................................................................................................. 2-12Package List ...................................................................................................................... 2-12Client Info ........................................................................................................................... 2-13Log Menu ........................................................................................................................... 2-13View Log ............................................................................................................................ 2-14View Job Log ..................................................................................................................... 2-14Set Log Level ..................................................................................................................... 2-15Set Job Log Level .............................................................................................................. 2-15Hide UI ............................................................................................................................... 2-16Chapter 3: Wireless ApplicationsIntroduction .................................................................................................................................... 3-1802.11d Overview .......................................................................................................................... 3-1Configuring My Country for Use with WLAN on an MC18 ............................................................. 3-1Enabled 802.11d Network ........................................................................................................ 3-2Disabled 802.11d Network ....................................................................................................... 3-2Create WCS Options Registry File .................................................................................... 3-2Update MC18 via 802.11d Enabled Staging Network ........................................................ 3-2Connect to the Non-802.11d Network ................................................................................ 3-3Wireless Application on the MC18T/MC18U ................................................................................. 3-3Signal Strength Icon ...................................................................................................................... 3-4Turning Off the Radio .................................................................................................................... 3-5

Table of Contents viiChapter 4: ActiveSyncActiveSync ..................................................................................................................................... 4-1Installing ActiveSync ...................................................................................................................... 4-1MC18 Setup ................................................................................................................................... 4-2Setting Up an ActiveSync Connection on the Host Computer ....................................................... 4-2Setting up a Partnership .......................................................................................................... 4-3Chapter 5: Using the Windows CE DesktopIntroduction .................................................................................................................................... 5-1ActiveSync ..................................................................................................................................... 5-1Remote Control Software ............................................................................................................... 5-1Connection to Host Computer ........................................................................................................ 5-1Programming Cable Removal .................................................................................................. 5-5App Launcher Window ................................................................................................................... 5-6Windows CE 7.0 Desktop .............................................................................................................. 5-7Status Icons ............................................................................................................................. 5-7Battery Unknown Icon .............................................................................................................. 5-8Start Button .............................................................................................................................. 5-9Programs Menu ....................................................................................................................... 5-9Desktop Display Button ............................................................................................................ 5-10Entering Information Using the Keyboard Input Panel ............................................................. 5-10Task Bar and Start Menu Properties ........................................................................................ 5-10Properties ........................................................................................................................... 5-10Advanced Tab .................................................................................................................... 5-11Screen Calibration ......................................................................................................................... 5-11Waking the MC18 .......................................................................................................................... 5-12Chapter 6: Special ConsiderationsIntroduction .................................................................................................................................... 6-1Fonts .............................................................................................................................................. 6-1Asian Font Installation .............................................................................................................. 6-2Software Development Considerations .......................................................................................... 6-2Tips for Improving Battery Charge Time ........................................................................................ 6-2Cradle-Backlight Feature ......................................................................................................... 6-3Tips for Improving Battery Life ....................................................................................................... 6-3Changing the Power Settings .................................................................................................. 6-4Changing the Display Backlight Settings ................................................................................. 6-4MC18U Support ....................................................................................................................... 6-5Chapter 7: Pocket BrowserIntroduction .................................................................................................................................... 7-1Sample Application ........................................................................................................................ 7-1Chapter 8: Cradle InstallationIntroduction .................................................................................................................................... 8-1Installation of the Cradle ................................................................................................................ 8-1Removing the Front Cover ....................................................................................................... 8-1

viii MC18 Product Reference GuideMounting the Cradle ................................................................................................................. 8-2Wiring ............................................................................................................................................. 8-4Assembly ....................................................................................................................................... 8-5Cradle Location Bar Code ........................................................................................................ 8-6System Cabling .............................................................................................................................. 8-7Mounting the Power Supply Housing ............................................................................................. 8-9Chapter 9: Application DeploymentSoftware Installation on Development PC ..................................................................................... 9-1Device Configuration Package ................................................................................................. 9-1Platform SDK ........................................................................................................................... 9-2Enterprise Mobility Developer Kits ........................................................................................... 9-2Installing Other Development Software ................................................................................... 9-2Deployment .................................................................................................................................... 9-3ActiveSync ............................................................................................................................... 9-3IPL ............................................................................................................................................ 9-4Creating Hex Images ..................................................................................................................... 9-5Starting Terminal Configuration Manager ................................................................................ 9-5Defining Script Properties ........................................................................................................ 9-7Creating the Script for the Hex Image ...................................................................................... 9-8Opening a New or Existing Script ...................................................................................... 9-8Updating TCM 1.X Scripts ................................................................................................. 9-8Copying Components to the Script .................................................................................... 9-8Saving the Script ................................................................................................................ 9-9Building the Image ................................................................................................................... 9-9Sending the Hex Image Using IPL ................................................................................................. 9-10TCM Error Messages ............................................................................................................... 9-14IPL Error Detection .................................................................................................................. 9-16Creating a Splash Screen ........................................................................................................ 9-18Splash Screen Format ............................................................................................................. 9-18OS Update ..................................................................................................................................... 9-19MC18 ....................................................................................................................................... 9-19MC18 ....................................................................................................................................... 9-21Flash Storage ................................................................................................................................ 9-23FFS Partitions .......................................................................................................................... 9-23Working with FFS Partitions ..................................................................................................... 9-23RegMerge.dll ...................................................................................................................... 9-23CopyFiles ........................................................................................................................... 9-24Non-FFS Partitions .................................................................................................................. 9-24Downloading Partitions to the MC18 ........................................................................................ 9-25Chapter 10: Maintenance and TroubleshootingIntroduction .................................................................................................................................... 10-1Maintaining the MC18 .................................................................................................................... 10-1Battery Safety Guidelines .............................................................................................................. 10-1Battery Management ..................................................................................................................... 10-2Clearing the Battery ................................................................................................................. 10-2Long Term Storage ........................................................................................................................ 10-3Cleaning ......................................................................................................................................... 10-4

Table of Contents ixMaterials Required ................................................................................................................... 10-4Cleaning the MC18 .................................................................................................................. 10-4Housing .............................................................................................................................. 10-4Display ............................................................................................................................... 10-4Scanner Exit Window ......................................................................................................... 10-4Connector ........................................................................................................................... 10-4Cleaning Cradle Connectors .................................................................................................... 10-5Cleaning Frequency ................................................................................................................. 10-5Troubleshooting ............................................................................................................................. 10-6MC18 ....................................................................................................................................... 10-6Cradle ...................................................................................................................................... 10-9Appendix A: Technical SpecificationsTechnical Specifications ................................................................................................................ A-1Cradle ...................................................................................................................................... A-3Cable Specifications ...................................................................................................................... A-6Power Supply Cable, Y-type .................................................................................................... A-6Cradle Interconnection Cable .................................................................................................. A-6Appendix B: AirBEAM Smart ClientIntroduction .................................................................................................................................... B-1AirBEAM Package Builder ............................................................................................................. B-1AirBEAM Smart Client .................................................................................................................... B-2AirBEAM License ..................................................................................................................... B-2Configuring the AirBEAM Smart Client .................................................................................... B-2Packages(1) Tab ................................................................................................................ B-2Packages(2) Tab ................................................................................................................ B-3Server Tab ......................................................................................................................... B-4Misc(1) Tab ........................................................................................................................ B-4Misc(2) Tab ........................................................................................................................ B-5Misc(3) Tab ........................................................................................................................ B-6Misc(4) Tab ........................................................................................................................ B-7Synchronizing with the Server ............................................................................................ B-8Manual Synchronization ..................................................................................................... B-9Automatic Synchronization ................................................................................................. B-9AirBEAM Staging ..................................................................................................................... B-9Appendix C: App Launcher ConfigurationConfiguration .................................................................................................................................. C-1GlossaryIndex

ABOUT THIS GUIDEIntroductionThis guide provides information about setting up and configuring MC18 mobile computers and installing its accessories.Documentation SetThe documentation set for the MC18 is divided into guides that provide information for specific user needs.MC18 documentation includes:•MC18 Quick Reference Guide - describes basic set up and operation of the MC18 and it’s cradles. The guide also includes regulatory and safety information.•MC18 Product Reference Guide (this guide) - describes how to set up, operate and program the MC18 and it’s accessories.•Microsoft Applications for Windows Mobile and WinCE 7.0 User Guide - describes how to use Microsoft developed applications.• Application Guide for Symbol Technologies Enterprise Mobility Devices - describes how to use Symbol Technologies developed applications.•EMDK Help File - provides API information for writing applications.Software VersionsThis guide covers various software configurations and references are made to operating system or software versions.OEM SoftwareUse this procedure to determine the OEM software version on the MC18:NOTE Some screens or windows shown in this guide may differ from the actual screens shown on the MC18.

xii MC18 Product Reference Guide1. Connect the MC18 to a host computer (see Connecting the MC18 to a Host Computer on page 4-2).2. Click Start > Settings > Control Panel > System Info icon.3. Make sure that the OEM software version on the MC18 is 99.42.00 or greater:Fusion SoftwareTo determine the Fusion software version on MC18 with OEM version X_2.01.0.0.062R or greater:Start > Programs > Fusion > Wireless status > Versions.Chapter DescriptionsTopics covered in this guide are as follows:•Chapter 1, Getting Started, describes the features and basic operation of the MC18, lists the accessories for the MC18 and explains how to install and charge the batteries and start the MC18 for the first time.•Chapter 2, Staging and Provisioning, provides information for staging and provisioning the MC18 using Mobility Software Platform (MSP).•Chapter 3, Wireless Applications, provides instructions for configuring the wireless adapter.•Chapter 4, Sync with Host Computer, provides instructions on installing a sync application and setting up a partnership between the MC18 and a host computer.•Chapter 5, Using the Windows CE Desktop, provides instructions for connecting the MC18 to a host computer and using the OS desktop of the MC18.

About This Guide xiii•Chapter 6, Special Considerations, provides information to consider when using and developing applications for the MC18.•Chapter 7, Pocket Browser, provides information on Sample Pocket Browser (mobile application development tool) provided with the MC18.•Chapter 8, Cradle Installation, provides installation instructions for the MC18 cradles and other accessories.•Chapter 9, Application Deployment, provides instructions for installing the Device Configuration Package (DCP) for MC18 and the EMDK for C on the host computer and downloading software and files to the MC18.•Chapter 10, Maintenance and Troubleshooting, includes instructions on cleaning and storing the MC18, and provides troubleshooting solutions for potential problems during MC18 operation.•Appendix A, Technical Specifications, includes a table listing the technical specifications for the MC18 and accessories.•Appendix B, App Launcher Configuration, provides information for configuring the App Launcher application.Notational ConventionsThe following conventions are used in this document:•“Mobile computer” refers to the Symbol Technologies MC18 of mobile computers. •Italics are used to highlight the following:•Chapters and sections in this guide•Related documents•Bold text is used to highlight the following:•Dialog box, window and screen names•Drop-down list and list box names•Check box and radio button names•Icons on a screen•Key names on a keypad•Button names on a screen.•Bullets (•) indicate:•Action items•Lists of alternatives•Lists of required steps that are not necessarily sequential.Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.NOTE This symbol indicates something of special interest or importance to the reader. Failure to read the note will not result in physical harm to the reader, equipment or data.CAUTION This symbol indicates that if this information is ignored, the possibility of data or material damage may occur.

xiv MC18 Product Reference GuideRelated Documents and SoftwareThe following documents provide more information about the MC18 mobile computers.•MC18 Quick Reference Guide, p/n MN000835A01•Microsoft Applications for Windows Mobile and CE 7.0 User Guide, p/n 72E-78456-xx•Enterprise Mobility Developer Kits, available at: •Device Configuration Package (DCP for MC18 v99.45.00xx) and Platform SDK for MC18 with Windows CE 7.0, available at: http://www.motorolasolutions.com/support•Latest ActiveSync (Windows xp) or Windows Mobile Device Center (Windows 7) software, available at: http://www.microsoft.com.For the latest version of this guide and all guides, go to: http://www.motorolasolutions.com/supportService InformationIf you have a problem with your equipment, contact Symbol Technologies Global Customer Support for your region. Contact information is available at: http://www.motorolasolutions.com/support. When contacting Symbol Technologies Global Customer Support, please have the following information available:•Serial number of the unit•Model number or product name•Software type and version number.Symbol Technologies responds to calls by E-mail, or telephone within the time limits set forth in support agreements.If your problem cannot be solved by Symbol Technologies Global Customer Support, you may need to return your equipment for servicing and will be given specific directions. Symbol Technologies is not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty.If you purchased your Symbol Technologies business product from a Symbol Technologies business partner, contact that business partner for support.WARNING!This symbol indicates that if this information is ignored the possibility that serious personal injury may occur.

CHAPTER 1 GETTING STARTEDIntroductionThis chapter describes the features of the MC18 and explains how to install and charge the battery, how to capture data using the integrated Imager and how to reset the MC18.UnpackingCarefully remove all protective material from the MC18 and save the shipping container for later storage and shipping.Verify that box contains all the equipment listed below:•MC18•Lithium-ion battery •Quick Reference GuideInspect the equipment for damage. If you are missing any equipment or if you find any damaged equipment, contact Symbol Technologies Support immediately. See Service Information on page xiv for contact information.Removing the Screen Protection FilmA screen protection film is applied to the MC18 screen to protect the screen during shipping. To remove the screen protector, carefully lift the thin film off the display.

1 - 2 MC18 Product Reference GuideFeaturesFigure 1-1 Front ViewMobile Computer SeriesStatus LEDDisplayScan KeyBranding Plate Slot

Special Considerations 1 - 3Figure 1-2 Back ViewBattery CoverSpeakerPower ConnectorScan Exit WindowBranding Plate Slot

1 - 4 MC18 Product Reference GuideAccessoriesTable 1-1 AccessoriesAccessory Part Number DescriptionMC18 Lithium Ion Battery BTRY-MC18-27MAG-01 MC18 Lithium Ion Battery.BTRY-MC18-27MAG-10 MC18 Lithium Ion Battery (QTY-10).High Density (HD) Three Slot Cradle (Locking).CRD-MC18-3SLCKH-01The cradle is used for docking up to three MC18 units in HD installation configuration. The cradle slots are equipped a mechanism that locks the MC18 units inside the slots.Three Slot Cradle Requires PWRS-14000-241R, DC line cord and Country Specific AC line cord sold separately.High Density (HD) Three Slot Cradle (Non-Locking)CRD-MC18-3SLOTH-01 The cradle is used for docking up to three MC18 units in HD installation configuration. Requires PWRS-14000-241R, DC line cord and country specific AC line cord (sold separately).Super High Density (SHD) Three Slot Cradle (Locking)CRD-MC18-3SLCKS-01 The cradle is used for docking up to three MC18 units in SHD installation configuration. The cradle slots are equipped a mechanism that locks the MC18 units inside the slots. Requires PWRS-14000-241R, DC line cord and country specific AC line cord sold separately.Single Slot CradleCRD-MC18-1SLOT-01 The cradle is used for docking a single MC18. Requires power supply unit (PWRS-14000-241R), DC line cord and country specific AC line cord sold separately.Release Key. KT-MC18-CKEY-20 Tool used to mechanically unlock the MC18 from a Three Slot Cradle. MC18 Terminal Reboot Tool KT-MC18-REBOOT-05 Tool used for cold reboot of the MC18 (QTY-5).Three Slot Cradle Front Panel Removing ToolKT-MC18-CTOOL-01 Tool used for removing the cradle cover. Deployment KitKT-MC18-CSTKIT-01 Includes: •20-pack of Release Key (KT-MC18-CKEY-20)•5-pack of Terminal Reboot Tool KT-MC18-REBOOT-05)•One Three Slot Cradle Front Panel Removing Tool (KT-MC18-CTOOL-01)Single Slot Cradle Release Key PSS-3KY01-00R Key used to mechanically unlock the MC18 from a single slot cradle (QTY-20).

Special Considerations 1 - 5Cart Holder Mounting Kit PSS-3SH01-00R Kit for mounting the MC18 on a shopping cart.Programming Cable CBL-MC18-USB1-01USB communication cable for connecting the MC18 to a host computer.Interconnection Cable 25-66431-01RAn extension cable (12.6 Inch / 32 centimeter) for connection three slot cradle to DC “Y” charging cable that is connected to power supply unit (PWRS-14000-241R). Power Extension Cable CBL-MC18-EXINT1-01Cable (12.6 Inch / 32 centimeter) for daisy chain connection of two Three Slot Cradles to one power supply unit (PWRS-14000-241R).DC Charging Cable 25-66420-01RDC charging cable (19.5 Inch / 49.5 centimeter) used to connect a power supply unit (PWRS-14000-241R) to one single-slot cradle.DC “Y” Charging Cable Long 25-67592-01RDC “Y” charging cable (39.7 Inch / 1 meter). Connects a power supply unit (PWRS-14000-241R) to two separate Three Slot Cradles.DC “Y” Charging Cable Short 25-66210-01RDC “Y” charging cable (19.5 Inch / 1 meter). Connects a power supply unit (PWRS-14000-241R) to two separate Three Slot Cradles.Power Supply UnitPWRS-14000-241R100-240VAC, 12VDC, 9A. Requires country specific AC line cord and DC cable - all sold separately. AC Line Cord 23844-00-00RAC Line Cord, 7.5 feet long, grounded, three wire for power supplies. Associated Country: United StatesAC Line Cord50-16000-221RAC Line Cord, 1.8 meter, meter grounded, three wire, USA NEMA 5-15P. Associated Country: United StatesAC Line Cord 50-16000-671RAC Line Cord, 1.8 meter, grounded, three wire, CIE 23-16 plug. Associated Country: Italy.AC Line Cord 50-16000-217RAC Line Cord, 1.9 meter, grounded, three wire, AS 3112 plug. Associated Country: Australia, New GuineaAC Line Cord 50-16000-218RAC Line Cord, 1.8 meter, grounded, three wire, NEMA 1-15P plug. Associated Country: Japan.AC Line Cord50-16000-219RAC Line Cord, 1.8 meter, grounded three wire, BS1363 plug. Associated countries: Hong Kong, Iraq, Malaysia, Singapore, United Kingdom.Table 1-1 AccessoriesAccessory Part Number Description

1 - 6 MC18 Product Reference GuideAC Line Cord50-16000-220RAC Line Cord, 1.8 meter, grounded three wire CEE 7/7plug. Associated countries: Europe, Abu Dhabi, Bolivia, Dubai, Egypt, Iran, Russia, Vietnam.AC Line Cord 50-16000-257RAC Line Cord, 1.8 meter, grounded three wire, IEC 60320 C13 plug. Associated Country: China.AC Li nd Cord50-16000-669R1.9 meter grounded three wire, BS 546 Plug. Associated country: India.AC Li nd Cord50-16000-672R1.9 meter grounded three wire, S132 Plug. Associated country: Israel.AC Li nd Cord50-16000-678R36 Inch grounded three wire.Associated country: United StatesTable 1-1 AccessoriesAccessory Part Number Description

Special Considerations 1 - 7Status LED The Status LED indicates the condition of the MC18. Table 1-2 describes the Status LED indications.Figure 1-3 MC18 Status LEDScan KeyThe scan key operates the imager camera when a scanning application is active. When turned off, pressing the scan key powers on the MC18. Note that Scan Key functions can be changed by an application so the MC18’s Scan Key may not function exactly as described. Refer to the EMDK Help file for detailed information for programming the Scan Key.Figure 1-4 Scan KeyTable 1-2 Status LED IndicationsLED State IndicationOffNormal operation or MC18 is turned off.Single Green blinkSuccessful Decode.Status LEDMobile Computer SeriesScan Key

1 - 8 MC18 Product Reference GuideGetting StartedTo start using the MC18 for the first time:•Install the battery•Charge the battery.Installing the BatteryTo start using the MC18, the battery must be installed and charged.To install the battery:1. Using Torx T8 drive, remove two screws that secure the battery cover.2. Lift the battery cover from the handle.3. Guide and press the battery cable connector into the female connector inside the battery compartment. The connector is designed to only fit one way. 4. Place the battery inside the battery compartment. 5. Place the battery cover onto the handle. 6. Secure the battery cover with the two Torx screws using a T8 Torx drive. Torque the screws to 3.6 Kgf-cm (3.1 in-lb).Figure 1-5 Installing the BatteryBattery CoverBatteryBattery CompartmentBattery Cable Connector

Special Considerations 1 - 9Removing the BatteryTo remove the battery:1. Use T8 Torx drive to remove the two screws that secure the battery cover.2. Lift the battery cover from the handle.3. Inside the battery compartment, press down the plastic tab of the Battery cable connector and slide it out of the female connector.4. Remove the battery from the battery compartment.Figure 1-6 Removing the BatteryCharging the Battery Before using the MC18 for the first time, charge the battery. The battery fully charges in approximately four hours.Use this procedure to charge the battery:1. Ensure the cradle is connected to the appropriate power source. See Chapter 8, Cradle Installation for more information.Battery CoverBatteryBattery CompartmentBattery Cable ConnectorPress down plastic tab to releaseCAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 10-1.NOTE Battery life is based upon the following; MC18 usage, WLAN radio is set to maximum power mode, WLAN is associated with an Access Point and display backlight set to 25% brightness.

1 - 10 MC18 Product Reference Guide2. Dock the MC18 in a cradle. The MC18 starts to charge automatically and is shown on the taskbar.Figure 1-7 Docking MC18 into CradleThree Slot CradleSingle Slot Cradle

Special Considerations 1 - 11Starting the MC18 The MC18 starts automatically as soon as power is applied; either with a charged battery installed or when inserted into the cradle.If charged battery is installed and the MC18 is turned off, hold the scan key pressed for five seconds to turn on. If the MC18 does not power on, perform a cold boot (see Performing a Cold Boot on page 1-17).When the MC18 is powered on for the first time, it initializes its system. The splash screen appears for a short period of time.Figure 1-8 Splash ScreenOn the MC18, the splash screen is followed by the App Launcher window.Figure 1-9 App Launcher WindowNOTE App Launcher window may vary depending upon the MC18 operating system version.

1 - 12 MC18 Product Reference GuideData CapturingThe MC18 uses a imager to allow collection of data by scanning bar codes.The scanner has the following features:•Reads a variety of bar code symbologies, including the most popular linear, postal, and 2-D code types (see Appendix , Technical Specifications).•Contains advanced intuitive aiming light for easy point-and-shoot operation.Scanning ConsiderationsTypically, scanning is a simple matter of aim, scan/decode and a few quick trial efforts master it. However, two important considerations can be used to optimize any scanning performance:•RangeAny scanning device decodes well over a particular working range — minimum and maximum distances from the bar code. This range varies according to bar code density and scanning device optics.Scanning within range brings quick and constant decodes; scanning too close or too far away prevents decodes. Move the MC18 closer and further away to find the right working range for the bar codes being scanned. However, the situation is complicated by the availability of various integrated scanning modules. The best way to specify the appropriate working range per bar code density is through a chart called a decode zone for each scan module. A decode zone simply plots working range as a function of minimum element widths of bar code symbols.•AngleDon’t scan at too sharp an angle; the scanner needs to collect scattered reflections from the scan to make a successful decode. Practice quickly shows what tolerances to work within.Scanning Bar Codes1. Ensure that a scan enabled application (for example: Scanning Sample) is loaded and enabled on the MC18.2. From the App Launcher screen, touch Demo Applications > Scanning Sample.3. Aim the scan exit window at the bar code.4. Press the scan key. Ensure the red aiming dot is at the center of the bar code. The LED changes from red to green and audible beep sounds if bar code was decoded successfully. Figure 1-10 Imager Aiming PatternNOTE Contact the Symbol Technologies Global Customer Support if chronic scanning difficulties develop. Decoding of properly printed bar codes should be quick and effortless. WrongRightRed Illumination LightRed Aiming Dot

Special Considerations 1 - 135. Release the Scan key. The bar code data is displayed on the screen.Figure 1-11 Scanning Sample Application ScreenScanning TipsOptimal scanning distance varies with bar code density and scanner optics.•Hold the scanner farther away for larger symbols.•Move the scanner closer for symbols with bars that are close together.DataWedgeDataWedge is an application that reads data from a scanning source, processes the data and sends the data to an application as if the user is entering it on a keyboard. By default, DataWedge is disabled. To use DataWedge Enable DataWedge.Enable DataWedgeUse this procedure to enable DataWedge:1. Select Start > Settings > Control Panel > DataWedge icon.2. Select Basic Configuration.3. Select 1. Scanner input.4. Select Low cost Imager:5. Select 1. Enabled.6. Click 0. Back.7. Click 0. Back.NOTE Scanning procedures depend on the application and MC18 configuration. An application may use different scanning procedures from the one listed above.

1 - 14 MC18 Product Reference Guide8. Click 0. Back.9. Click 0. Exit.Figure 1-12 DataWedge Stopped10. Select Running to start the DataWedge process. The DataWedge Status changes to Ready.Figure 1-13 DataWedge Running11. Click OK to exit.Disable DataWedgeUse this procedure to disable DataWedge:1. Select Start > Settings > Control Panel > DataWedge icon.2. Select the Running option to end the DataWedge process. The DataWedge Status changes to Stopped.3. Select OK.Using DataWedge to Read bar CodesTo read bar codes with DataWedge:1. Enable DataWedge.2. Open an application and select a text box or field for entering the bar code data.3. Use one of the optional scanners and capture the bar code data. The data appears in the text box.

Special Considerations 1 - 15Manual Release of MC18 from CradlesThe MC18 cradles contain a locking mechanism that locks the MC18 inside the cradle when docked. The MC18 releases from the cradle when a software command is received from the system. If the MC18 fails to un-lock during normal operation, use a release key to un-lock the MC18.Manual Release of MC18 from the Single-Slot CradleTo release a locked MC18 from a single slot cradle:1. Insert the release key into the slot located at the bottom side of the cradle.2. While pressing the release key all the way into the slot, remove the MC18 from the cradleFigure 1-14 Manual Release of MC18 from a Single Slot CradleThree Slot CradlesTo release a locked MC18 from a three slot cradle:1. Insert the release key straight into the slot, to a point where the bend stops.2. Hold the release key pressed inside the slot and remove the MC18 from the slot.NOTE The MC18 also can be released by software command using the PocketBrowser application (see Sample Application on page 7-1).ABRelease KeyNOTE The cradle includes models that do not have locking mechanism. To identify the model of cradle, refer to Table 1-1 on page 1-4.NOTE The MC18 also can be released by software command using the Cradle Utility application (see Setting and Controlling the Cradle on page 6-9).

1 - 16 MC18 Product Reference GuideFigure 1-15 Manual Release of MC18 from a Three Slot CradleResetting the MC18There are two types of resets, warm boot and cold boot. A warm boot restarts the MC18 by closing all running programs.A cold boot also restarts the MC18, but erases all stored records and entries in RAM. In addition it returns formats, preferences and other settings to the factory default settings.Perform a warm boot first. This restarts the wearable terminal and saves all stored records and entries. If the wearable terminal still does not respond, perform a cold boot.Performing a Warm BootUse this procedure to perform a warm boot:1. From the Start menu, click Programs to launch the Programs menu. 2. Click Warm Boot.Figure 1-16 Performing a Warm BootRelease Key

Special Considerations 1 - 17Performing a Cold BootA cold boot restarts the MC18 and erases all user stored records and entries that are not saved in flash memory (Application and Platform folders). Never perform a cold boot unless a warm boot does not solve the problem.Performing Cold Boot when the MC18 is Docked Inside the CradleUse this procedure to perform a cold boot when the MC18 is docked inside the cradle:1. Press and hold the scan key for 10 seconds until the display powers off.2. Release the scan key when the MC18 re-boots.Performing Cold Boot when MC18 is Out of the CradleUse this procedure to perform a cold boot when the MC18 is out of the cradle:1. Insert the terminal reboot tool into the MC18 power connector and then press and hold the scan key for 10 seconds until the display powers off - the MC18 reboots. 2. Release the scan key and remove the terminal reboot tool from the MC18.Figure 1-17 Terminal Reboot Tool NOTE Any data previously synchronized with a computer can be restored during the next ActiveSync operation.Terminal Reboot ToolScan KeyPower Connector

2 - 2 MC18 Product Reference GuideFigure 2-1 RD Bar Code Printout SampleBar Code StagingWhen the MC18 boots for the first time (or after a cold boot) the App Launcher window appears. The RD Client option is highlighted.Use this procedure to set bar code:1. Obtain the appropriate RD bar code sheet from the MSP Administrator.2. On the App Launcher screen, click Rapid Deployment Client.3. Result: The Scan Barcodes To Deploy window displays.NOTE If the App Launcher screen does not display see your administrator.

2 - 6 MC18 Product Reference GuideFigure 2-9 Staging Complete WindowUse Options > Exit button in RD client application to exit.RD Client Main MenuThe RD Client Main Menu contains the following options:•Search Connected Networks. See On-Demand Staging on page 2-4 for detailed information.•Search Unconnected Networks. See On-Demand Staging on page 2-4 for detailed information.•Scan Barcodes See Bar Code Staging on page 2-2 for detailed information.•View Client Info•Log Menu•Package List•Exit - Closes the RD Client application.Figure 2-10 RD Client Main MenuClient InfoUse the Client Info window to view the following information:•RD Client version•Product name

Staging and Provisioning 2 - 7•Operating system type•Plug-in type.Select View Client Info option.Figure 2-11 Client Info WindowPress the OK to return to the Main Menu.Log MenuThe Log Menu contains the following options:•View Log•View Job Log•Set Log Level•Set Job Log Level.Select Log Menu option.Figure 2-12 Log Menu WindowPress OK to return to the Main Menu.View LogUse the View Log option to display a list of events that have occurred.

2 - 8 MC18 Product Reference GuideSelect View Log option.Figure 2-13 View Log WindowReturn to the Log Menu.View Job LogUse the View Job Log option to display a list of jobs that have be processed.Select View Job Log option.Figure 2-14 View Job Log WindowReturn to the Log Menu.Set Log LevelUse the Set Log Level option to set the level of the information that appears in the log.

Staging and Provisioning 2 - 9Figure 2-15 Set Log Level WindowSelect a level option.Set Job Log LevelUse the Set Job Log Level option to set the level of the information that appears in the Job log.Figure 2-16 Set Job Log Level WindowSelect a level option.Package ListUse the Package List option to display the packages that have been installed on the MC18.Select the Package List option.

2 - 10 MC18 Product Reference GuideFigure 2-17 Package List WindowReturn to the Main Menu.

Staging and Provisioning 2 - 11ProvisioningProvisioning is the process of installing software packages onto the MC18 mobile computers.MSP AgentThe Provisioning Client is responsible for implementing device-side provisioning activities as defined by a policy. A policy is evaluated on the MSP 3.X system and delivered to mobile computers as job documents via relay servers.The MSP 3.X Provisioning Client is 100% backward compatible to prior versions of the AirBEAM Client. Existing AirBEAM Smart users can use the MSP 3.X Provisioning Client as a 100% backward compatible replacement for prior versions of AirBEAM Client, when used in classic AirBEAM mode with existing FTP servers.Existing MSP 2.X users can use the new Provisioning Client as a 100% backward compatible replacement for previous versions of AirBEAM Client, when used in Level 2 Agent and Level 3 Agent modes with existing MSP 2.X Appliances.For more detailed information on MSP Agent (Provisioning Client), refer to the MSP 3.X User's Guide (p/n 72E-100158-xx).MSP Agent Main MenuThe MSP Agent Main Menu contains the following options:•Monitoring Processing•Force Check-In•Package List•View Client info•Log Menu•Hide UI•Exit - exits the MSP Agent application.Figure 2-18 MSP Agent Main MenuNOTE MSP Agent is also known as MSP 3.X Provisioning Client.

2 - 12 MC18 Product Reference GuideMonitor ProcessingUse the Monitor Processing option to view the status of packages being processed.Select the Monitor Processing option.Figure 2-19 Monitor Processing WindowPress Main Menu to return to the Main Menu.Force Check-InUse the Force Check-In option to check instantly for pending package downloads instead of waiting for the next automatic check that the client performs.Select the Force Check-In option.Figure 2-20 Force Check-in WindowPress Main Menu to return to the Main Menu.Package ListUse the Package List option to display the packages that have been installed on the MC18.Select the Package List option.

Staging and Provisioning 2 - 13Figure 2-21 Package List WindowPress OK to return to the Main Menu.Client InfoUse the Client Info window to view the following information:•RD Client version•Product name•Operating system type•Plug-in type.Select View Client Info option.Figure 2-22 Client Info WindowPress OK to return to the Main Menu.Log MenuThe Log Menu contains the following options:•View Log•View Job Log•Set Log Level•Set Job Log Level.

2 - 14 MC18 Product Reference GuideSelect Log Menu option.Figure 2-23 Log Menu WindowPress OK to return to the Main Menu.View LogUse the View Log option to display a list of events that have occurred.Select View Log option.Figure 2-24 View Log WindowPress OK to return to the Log Menu.View Job LogUse the View Job Log option to display a list of jobs that have be processed.Select View Job Log option.

Staging and Provisioning 2 - 15Figure 2-25 View Job Log WindowPress OK to return to the Log Menu.Set Log LevelUse the Set Log Level option to set the level of the information that appears in the log.Figure 2-26 Set Log Level WindowSelect a level option.Set Job Log LevelUse the Set Job Log Level option to set the level of the information that appears in the Job log.

2 - 16 MC18 Product Reference GuideFigure 2-27 Set Job Log Level WindowSelect a level option.Hide UIUse the Hide UI option to minimize the MSP Agent application. The MSP Agent application runs in the background while minimized.To un-hide the application, select the MSP Agent icon in the task tray and select the UnHide UI menu item.Figure 2-28 UnHide UI SelectionMSP Agent Icon

CHAPTER 3 WIRELESS APPLICATIONSIntroductionWireless Local Area Networks (WLANs) allow the MC18 mobile computers to communicate wirelessly and send captured data to a host device in real time. The MC18 supports the 802.11a, 802.11b, 802.11g and 802.11n standards. Before using the MC18 on a WLAN, the facility must be set up with the required hardware to run the wireless LAN and the MC18 must be configured. Refer to the documentation provided with the access points (APs) for instructions on setting up the hardware.To configure the radio in the MC18, use the Fusion APIs in the Enterprise Mobility Developer’s Kit (EMDK). Refer to the EMDK Help file for detailed information.The MC18 contain the Wireless Applications to allow configuration of the WLAN radio. On the MC18, use the touch screen to access the Wireless Application. MC18 requires the use of remote control software. See Chapter 4, Sync with Host Computer for more information.802.11d OverviewIEEE 802.11d, is an amendment to the IEEE 802.11 specification that adds support for additional regulatory domains. This includes additional country information to beacons, probe requests, and probe responses. The country information simplifies the creation of 802.11 wireless access points (APs) and clients that meet the different regulations enforced in various parts of the world.Fusion fully supports 802.11d for Regulatory purposes. By using 802.11d, the MC18 can easily connect to a wireless network and use only the valid channels for the country specified in the AP's beacons. By default, the MC18 software enables 802.11d mode to determine regulatory requirements.Configuring My Country for Use with WLAN on the MC18Configuration can be done on:•an enabled 802.11d network•a disabled 802.11d network.

3 - 4 MC18 Product Reference GuideFigure 3-1 Wireless Applications MenuSignal Strength IconThe Signal Strength icon in the task tray indicates the MC18 wireless signal strength as follows:Signal Strength IconTable 3-1 Wireless Applications Icons, Signal Strength DescriptionsIcon Status ActionExcellent signal strength Wireless LAN network is ready to use.Very good signal strength Wireless LAN network is ready to use.Good signal strength Wireless LAN network is ready to use.Fair signal strength Wireless LAN network is ready to use. Notify the network administrator that the signal strength is only “Fair”.Poor signal strength Wireless LAN network is ready to use. Performance may not be optimum. Notify the network administrator that the signal strength is “Poor”.Out-of-network range (not associated)No wireless LAN network connection. Notify the network administrator.

3 - 6 MC18 Product Reference Guide3. Click Next on New Connection wizard to start device discovery.4. Select the printer and choose next to start pairing process.5. Enter the PIN. Once the printer is paired with MC18, services of printer are listed.6. Choose serial printer service and connect. 7. Select the port MC18 to connect to printer.

CHAPTER 4 SYNC WITH HOST COMPUTERTo communicate with a host computer, the host computer requires a synchronization program. After synchronizing the MC18 with a host computer, changes made on the MC18 or host computer appear in both places.To communicate with a host computer running Windows XP, install Microsoft ActiveSync (version 4.5 or higher). To communicate with a host computer running Windows 7, install Windows Mobile Device Center (WMDC version 6.1 or higher). Using a synchronization software:•Allows working with MC18-compatible host applications on the host computer. The synchronization software replicates data from the MC18 so the host application can view, enter, and modify data on the MC18.•Synchronizes files between the MC18 and host computer, converting the files to the correct format.•Backs up the data stored on the MC18. Synchronization is a one-step procedure that ensures the data is always safe and up-to-date.•Copies (rather than synchronizes) files between the MC18 and host computer.•Controls when synchronization occurs by selecting a synchronization mode, e.g., set to synchronize continually while the MC18 is connected to the host computer, or set to only synchronize on command.•Selects the types of information to synchronize and controls how much data is synchronized.Installing the Synchronization SoftwareTo install ActiveSync or Windows Mobile Device Center software on the host computer, logon to Microsoft web site at http://www.microsoft.com. Refer to the installation instructions included with the software.

4 - 2 MC18 Product Reference GuideConnecting the MC18 to a Host ComputerPerform this procedure to connect the MC18 to a host computer:1. Ensure that synchronization program (ActiveSync for Windows XP or Windows Mobile Device Center for Windows 7) is installed properly on the host computer.2. Using a T8 Torx drive, remove the two Torx screws securing the battery cover to the back housing of the MC18 (see Figure 4-1).Figure 4-1 Remove Battery Cover3. Align the connector on the programming cable panel with the sync connector on the MC18 and lower the panel to fit on the MC18.4. Hand-tighten the two T8 Torx screws securing the programming cable panel to the MC18.Battery CoverCAUTION Do not remove the battery cover while the MC18 is on and do not operate the MC18 with the battery cover removed. Follow proper Electro-Static Discharge (ESD) precautions to avoid damaging the MC18. Proper ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.

Sync with Host Computer 4 - 3Figure 4-2 Installing the Programming Cable5. Set the switch on programming cable of the programming cable panel to the side marked with a dot (see Figure 4-2).6. Connect the USB connector of the programming cable panel to the Host Computer. The host computer automatically detects the MC18 and starts ActiveSync or Windows Mobile Device Center - the synchronization program window appears on the host computer screen.Dot ConnectorProgramming CableProgramming Cable PanelHost ComputerSync ConnectorSwitch

4 - 4 MC18 Product Reference GuideFigure 4-3 Synchronization Program Windows7. For ActiveSync, select the Yes radio button to create a partnership with the host computer or No radio button to connect as a guest.For Mobile Device Center, select Set up your device or select Connect without setting your device to connect as a guest.8. For ActiveSync, click Next. The Microsoft ActiveSync window indicates that it is connected to the MC18.For Windows Mobile Device Center, select the required option.Figure 4-4 ActiveSync / Windows Mobile Device Center Connected WindowWindows Mobile Device CenterActiveSyncWindows Mobile Device CenterActiveSync

Sync with Host Computer 4 - 5Removing the Programming Cable PanelPerform this procedure to remove the programming cable panel.1. Using a T8 Torx drive, loosen the two screws securing the programming cable panel to the MC18.2. Lift the programming cable panel straight up.Installing the Battery Cover1. Align the battery cover on the MC18 and lower the panel to fit on the MC18.2. Using a T8 Torx drive, secure with battery cover to the MC18 using the two Torx screws. Torque the screws to 3.6 kgf/cm (3.1 in-lbs).Setting Up an ActiveSync Connection on the Host Computer (with Windows XP)Use this procedure to start ActiveSync:1. Select Start > Programs > Microsoft ActiveSync on the host computer. The ActiveSync window displays.Figure 4-5 ActiveSync Window2. In the ActiveSync window, select File > Connection Settings. The Connection Settings window appears.CAUTION Follow proper Electro-Static Discharge (ESD) precautions to avoid damaging the MC18. Proper ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.NOTE The normal function of the product may be disturbed by Strong Electro Magnetic Interference (for example, static electricity). If so, simply remove and re-insert the MC18 to resume normal operation. In case the function does not resume, please use the product in another location.NOTE Assign each MC18 a unique device name. Do not try to synchronize more than one MC18 to the same name.

4 - 6 MC18 Product Reference GuideFigure 4-6 Connection Settings Window3. Select Allow USB connections check box.4. Select the Show status icon in Taskbar check box.5. Select OK to save any changes made.Setting up a PartnershipUse this procedure to set up a partnership:1. If the Get Connected window does not appear on the host computer, select Start > All Programs > Microsoft ActiveSync.Figure 4-7 New Partnership Window2. Select if you want to set up a partnership. Select either the Yes or No radio button.3. Click Next.4. If No is selected, skip to step 7.

Sync with Host Computer 4 - 7Figure 4-8 Select Synchronization Setting Window5. Select the appropriate settings and click Next.Figure 4-9 Setup Complete Window6. Click Finish.7. The Microsoft ActiveSync window displays.

4 - 8 MC18 Product Reference GuideFigure 4-10 ActiveSync Connected WindowDuring the first synchronization, information stored on the MC18 is copied to the host computer. When the copy is complete and all data is synchronized, the MC18 can be disconnected from the host computer.For more information about using ActiveSync, start ActiveSync on the host computer, then see ActiveSync Help.Setting Up a Windows Mobile Device Center Connection on the Host Computer (with Windows 7)To set up a Sync connection using Windows 7:1. Select Start > All Programs > Windows Mobile Device Center on the host computer.Figure 4-11 Windows Mobile Device Center (WMDC) WindowNOTE The first ActiveSync operation must be performed with a local, direct connection. To retain partnerships after a cold boot, capture partnership registry information in a .reg file and save it in the Flash File System, See the detailed information provided in the EMDK Windows CE Help File for Mobile Computers.

Sync with Host Computer 4 - 92. In the WMDC window, under Mobile Device Settings, click Connection settings.Figure 4-12 Connection Settings Window3. Select Allow USB connections and adjust any additional settings as needed.4. Click OK to save your settings.Setting up a PartnershipTo set up a partnership:1. In the WMDC window, under Mobile Device Settings, click Set up your device.2. Check the Files check box and click Next.Figure 4-13 Select Synchronization Setting Window

4 - 10 MC18 Product Reference Guide3. Set your device name and click Set Up - the Connected Window will display.Figure 4-14 Setup Complete WindowFigure 4-15 Connected WindowDuring the first synchronization, information stored on the MC18 is copied to the host computer. When the copy is complete and all data is synchronized, the MC18 can be disconnect from the host computer.For more information about using WMDC, start the application on the host computer, then see Help.

CHAPTER 5 USING THE WINDOWS CE DESKTOPIntroductionThe MC18 runs Windows CE 7.0 operating system and the operating system is only available for configuration when connected to a host computer via sync program.The MC18 enabled device is available using the user interface (UI).App Launcher WindowThe App Launcher window allows the user to launch specific applications by tapping on a menu an item. If the App Launcher window is closed, launch the App Launcher window by touching the App Launcher shortcut on the MC18 desktop or selecting AppLauncher.exe in the Start > Programs > Windows Explorer directory.See Appendix B, App Launcher Configuration for instructions on modifying the App Launcher menu.NOTE App Launcher window may vary depending upon the operating system version.

5 - 2 MC18 Product Reference GuideFigure 5-1 App Launcher WindowTable 5-1 App Launcher Item DescriptionsItem DescriptionRapid Deployment ClientLaunches the Rapid Deployment application.File ExplorerFile Explorer enables working with files, folders and network on the MC18.UtilitiesProvides easy access to most used applications such as Internet Explorer.Cradle ApplicationsProvides for cradle software update, control and settings and diagnostics applications.Demo ApplicationsProvides applications that demonstrate the operation of the MC18 such as scan application.Test ApplicationsProvides applications for performing diagnostics and testing of the MC18.AboutDisplays information about the App Launcher.ExitCloses the Up Launcher window.

Using the Windows CE Desktop 5 - 3Windows CE 7.0 DesktopThe following paragraphs describe the Windows CE 7.0 desktop. Depending upon the customer’s configuration of the MC18, the desktop may not be available.Status IconsThe Taskbar at the bottom of the window displays the active programs, battery status and communication status. The taskbar (at the bottom of the screen) displays the Start button, active programs, battery status and communication status. The taskbar icons are described in Table 5-2. The taskbar icons display the function status, indicate what programs are active and indicate the battery charge status. The Taskbar buttons are used to access menus, select/deselect functions or to change display windows.•Active Programs Icons: The active applications icons are displayed on the taskbar. If more than one program is active, icons can be used to toggle between the open programs (applications). Touch on a taskbar application to maximize the application. •AC Power/Battery Status Icons: The AC Power/Battery Status icons are shown in the taskbar to indicate the present power supply status of the MC18. The battery status icons provide the battery status in 10% increments from 10% to 100%. The Taskbar is shown on the lower part of the MC18 screen. To set the properties of the taskbar, see Properties on page 5-6.Figure 5-2 TaskbarNOTE The Windows CE 7.0 desktop may not be visible because the App Launcher application is active. To view the desktop, close all running applications.Start Button Status IconsTask b a r

5 - 4 MC18 Product Reference GuideFigure 5-3 TaskbarStart ButtonTouch the Start button to launch the Start menu.•Programs: Use to access available programs.•Favorites: Displays files in Favorites directory.•Documents: Displays files in Documents directory.•Settings: Accesses the Control Panel, the Network and Dial-up Connections and the Taskbar and Start menu.•Help: Accesses the Windows CE Help.•Run . . . : Runs a program or application.•Suspend: Places the MC18 in the suspend state.Table 5-2 Taskbar IconsIcon DescriptionIndicates that the battery is charging.Indicates that the battery is fully charged (100% charged).The battery status icons provide the battery status in 10% increments from 10% to 100%.Indicates that the battery is fully charged and the MC18 is running on external power.Indicates IP status. Only displays when the MC18 is in emulation mode.Indicates that the Sync application is running.Indicates that the wireless application radio is connected to a wireless LAN network with excellent signal strength.Indicates that the wireless application radio is not connected to a wireless LAN network. Start ButtonTask Bar with Status IconsKeyboard Input Panel ButtonDesktop Display ButtonCurrently Open Programs Scroll Status Icons

Using the Windows CE Desktop 5 - 5Figure 5-4 Start MenuPrograms MenuFrom the Start menu, click Programs to launch the Programs menu. Refer to the Application Guide for Symbol Technologies Enterprise Mobility Devices, p/n 72-68901-xx and the Microsoft® Applications for Windows Mobile and WinCE 7.0 User Guide, p/n 72E-78456-xx for application information.Figure 5-5 Programs MenuDesktop Display ButtonUse the Desktop Display button to minimize all open programs and display the desktop.Entering Information Using the Keyboard Input PanelsUse the keyboard input panels (soft keyboard) to enter information in any program. To launch the keyboard input panel, click the button on the taskbar. Select the type of input panel (Keyboard or XAMLIM). Touch a key to enter the value. Touch the keyboard input panel button to display or to hide the keyboard input panel.

5 - 6 MC18 Product Reference GuideFigure 5-6 Keyboard Input PanelTask Bar and Start Menu PropertiesUse the Properties functions to set display and clock options.Properties1. Touch Start > Settings > Taskbar and Start Menu ... . The Taskbar and Start Menu window displays.Figure 5-7 Taskbar and Start Menu- General Tab2. This window provides taskbar options:•Check the Always on Top check box to keep the taskbar on top of all other windows. •Check the AutoHide check box to make the taskbar disappear, click the bottom of the display to make the taskbar return.•Check the Show Clock check box to display the clock on the taskbar.3. Tou c h OK to save the settings and exit the window.Advanced Tab1. Touch the Advanced tab.KeyboardXAMLIM

Using the Windows CE Desktop 5 - 72. Touch the Clear button to delete all of the documents listed in the Start > Documents entry, see Start Button on page 5-4. Typically this list is empty, but if there were documents in the list the Clear button would delete them.3. Touch the Expand Control Panel check box to display the entire contents of the Control Panel in list form, rather than icons.Figure 5-8 Taskbar and Start Menu-Advanced Tab4. Touch OK to save the settings and exit the window.Waking the MC18The wake up conditions define what actions wake up the MC18 after it has gone into suspend mode. The MC18 can go into suspend mode automatically by control panel time-out settings. These settings are configurable and the factory default settings are shown in Table 5-3. To set the wake up conditions select Start > Settings > Control Panel > Power icon > Wakeup tab.Figure 5-9 Wakeup TabTable 5-3 Wakeup Default SettingsCondition for Wakeup Automatic Time-outTouch Panel (Screen) NoTrigger 1 (Scan key) YesUSB Cable Yes

CHAPTER 6 SPECIAL CONSIDERATIONSIntroductionThe chapter provides information for:•Using language fonts•software development considerations•Improving battery charge time•Improving battery life•Cradle applications•MC18 Hardware DiagnosticsFontsThe MC18 supports the following language fonts:•English•French•Italian•German•Spanish•Swedish•Russian•Greek (fonts support only)•Arabic (fonts support only)The MC18 supports the installation of font libraries for use with application and web development. Simplified Chinese, Korean, and Japanese font libraries are available on the Support Central Web site, http://supportcentral.motorola.com. Other standard UTF-8 encoded fonts are available from third party font

6 - 2 MC18 Product Reference Guidevendors. Developers should refer to Microsoft and third party vendor documentation for development and usage details.It should be noted that installing a language font library will not change the language configuration of the operating system image, i.e., Windows messages will still be displayed in the language designated in the factory supplied operating system image.

$Special Considerations 6 - 51. Select Start > Settings > Control Panel > Backlight icon > Battery Power tab.2. Select the On battery power: Disable backlight if not used for: check box and select a value from the drop-down list box.3. Select the Brightness tab.4. Select the Disable backlight check box to completely turn off the display backlight.5. Use the slider to set the brightness of the backlight. Set it to a low value to save battery power.6. Select OK.The display backlight value can also be set using a registry setting.Key Name: [HKEY_CURRENT_USER\ControlPanel\BackLight]"BatteryTimeout"=dword:00000000 ; timeout set to never"ACTimeout"=dword:00000000 ; timeout set to neverNOTE By default, backlight is set NOT to time-out on user inactivity – this can be modified using the Backlight control panel applet.$